Benzotrimmer energy industry how to collect and dry. What is a fuel mixture and how to cook it?

Proper operation of a trimmer for grass for grass

In every summer village, village, suburb and in the city itself you can see these devices: they work tirelessly, aligning the lawn grass, cleansing the space of squares and parks, gardens and gardens from thickets of burdock, wormwood and weeds. The noise and crackle from the trimmers are heard from the beginning of summer to autumn, until the growth of the grass is so much so that it will no longer need to trim it. Automatic braid for grass deserved its popularity for the simplicity of the device and operation. It is easy for her to use, it is easy to care for, and in case of breakdown it is not possible to easily fix it without difficulty. The article will just tell you how to use a trimmer for grass correctly.

As with any other technique, in working with the trimmer there are rules. First you need to make sure that the main nodes and assemblies: screw, rods, handles and motor. If the device has not yet been assembled, then it should be correctly assembled according to the instructions.

Gasoline unit

In the case of a gasoline trimmer, it is necessary to check the gearbox for lubrication. Also, do not forget to add lubricants to the fuel tank, if the instruction manual is evidenced. As a rule, gas and oil are mixed in a ratio of 45 to 1, but these indicators may vary depending on the model and manufacturer, so you should carefully study all the technical requirements for the device. The fuel container must be filled on the very neck. If all technical fluids are flooded, then you can try to start the device. But it’s not worth mowing right away, it will be better to let the trimmer work without load so that the engine works to the flooded fuel. A few minutes will be enough, after which you can give the motorcycle full load.

Elektokos

With an electric trimmer, everything is much easier. Having made sure that the gearbox has the required amount of lithol, you can start work. No additional measures are required. Unless it is necessary to make sure that the carrying does not run on the path of mowing in order to avoid possible damage.

When the device itself is ready to work, you should make sure that there is nothing around that could interfere with the work. If possible, the estimated mowing area should be cleaned of snags, glass, stones and other solid objects that can damage a knife or fishing line for a trimmer.

benzotrimmer, collect, fuel, mixture

It is better if other people do not approach the trimmer while working. Usually the recommended distance is at least 10-15 meters in order to avoid small debris (mulch) in the eye and on the face.

Depending on the upcoming work, you need to choose a nozzle for a trimmer for the grass: a screw-knife for weeds and hay, a fishing line for a trimmer for lawn grass or a disk saw for shrubs. Mowing should be in the opposite direction from people, if possible, moving away from buildings and buildings. You should not get too close to the fence and other designs, since the fishing line for a trimmer can catch on sharp edges, and the screw-knife will bend if it accidentally offends it a hard object.

The preparation of the device itself will not take much time, all modern models of devices are designed to facilitate and simplify their operation, starting to work in the shortest possible time.

We run up a gasoline trimmer for grass

Most often, the running.in is used in a motorcycle (trimmer for gasoline grass). The running.in is the operation of the engine at low speeds, without loads. To run, it is necessary to start a motorcycle and let it work at idle. It is best to produce the first mowing with a fishing line, since when mowing lawn grass is a less high load on the engine than when working with hay or shrubs.

The load must be increased gradually, in stages increasing engine speed. If you start operating with high speeds, the engine can be poorly developed, which will affect the entire further operation of motorcycles.

Do not produce the entire temporary resource during the first engine start. It will be best after working at idle by idle for 10-15 minutes to mow, then drown out the device and let it cool a little. Use a motorcycle system carefully, without sudden movements, in order to avoid collisions with solid objects (stones). The stab on the stone can poorly affect the work of the unfortunate nodes. In some cases, backlash, noise and hum during operation appear. This can be easily avoided if the trimmer for the grass is correctly running.

– Unpacking

We will analyze the example of a popular fubag fpt43 chain.alcohol. It is easy to manage and a very reliable unit with the most running engine for 1.3 kW.

A braid for grass is delivered in a disassembled form and consists of: motor unit, rod, T-shaped Handles and protective casing. The set includes instruction manual.

This model allows you to work both fishing line on the grass and a cutting disk on dry stems and branches. both are already in the kit.

In addition to the main parts, which is very pleasant, Fubag equips a braid with a set of tools, a container for gasoline mixture, belt and reliable protective glasses.

– Assembly of braids for grass

So, first you need to properly assemble the lawn mower. It is very simple.

1) Combine the bar and the engine. To do this, align the bar with respect to the engine so that the spindle is located in the same plane with the fuel tank of the engine.

2) install the bar flange in the engine and fix it with 4 screws.

To do this, unscrew the screw “lamb” on the top cover of fasteners. And remove the top cover. Next, insert the handle into the fasteners, set the lid, tighten the screw. We put the control handle on the pipe and fix the screw. On this trimmer, the adjusting screw allows you to configure the handle for the user: you just need to loosen the “lamb” and move to the required distance, and then fix it.

To do this, we compatrate the holes in the protective casing with holes in the mounting bar and fix the protective casing on the bar with screws with washers using the key. The key is included. Pay attention to the fastening of the casing. On the Fubag FPT43 model, they are metal and on both sides. this guarantees the reliability of fastening and the safety of your work.

We connect the triss of the throttle to the engine and insert its end into the hinges of the throttle. We connect the red wire of the control handle to the red wire of the engine, and black to black.

The fastening of the cable to the hinge of the throttle must be carried out in such a way that when pressing the gas trigger on the handle there is some free stroke of the cable, and only then the opening of the damper. This is necessary so that the engine does not have increased speed at idle.

To do this, you need to combine the hole in the flange washer with the hole in the gearbox cup. Next. insert a metal stopped rod into the hole of the gearbox cup and into the hole of the flange washer.

Remove the cup from the shaft, leaving the flange washer and install the cutting knife on the flange washer. Check that the cutting knife is correctly specified and lies on the puck groove. Now we install a clamping puck, on the shaft of the mount, make a nut. Holding the stopped rod with one hand, reliably tighten the nut with a tubular key, turning it counterclockwise.

8) If we need a coil with a fishing line: combine a hole in a flange washer with a hole in a cup of the gearbox. You also need to insert a metal stopped rod into the hole of the gearbox cup and into the opening of the flange washer. Unscrew the nut from the hub of the product clockwise and remove the cup from the shaft, a clamping puck, leaving only a flange.

9) holding the rod, twist the coil with a fishing line counterclockwise until it stops. It remains to install a biceps belt. We attach the carabiner of the shoulder belt to the ring for fastening the shoulder belt. Adjust the position of the ring on the bar of the product and fix it with a fixing screw. Adjust the length of the shoulder belt.

T.to. On this model, a single.cylinder two.stroke engine, then it works, respectively, from the fuel mixture.

Launching a lawn mower with an unfinished engine

For the first launch of the lawn mower, find the air damper lever and put it in position “Closed”. Turn on the ignition on the handle. If your model has a manual fuel pump, the people are called a suction, then click on it 3-5 times until you see the fuel mixture inside the primer. Now the tool is ready to launch. Put a trimmer for grass on a flat surface to ensure a stable position. Smoothly stretch the trigger cable until you feel its resistance, and then pull the cord with a sharp movement 3-5 times.

If the engine started after 5 jerks, then open the air damper. If this does not happen, still open the air damper (with an open damper and continuation of attempts to start the engine, the fuel flows a candle and you will have to dry it, and this is extra waste).

If the engine does not start, with an open damper, then close it to continue to pull the cord. The first launch may be quite difficult and demand up to 15 jerks. After the engine has begun to work, click once on the gas lever, so you will use idle. Now let the engine work and warm up. After that, it can be stopped by pressing the “Stop” button.

The main malfunctions of the starter of the trimmer for grass

It is not difficult to determine the cause of the breakdown of the starting device. There are several main options:

These details are shown in the photo below.

It may happen that the starting mechanism will be accidentally broken. The consequences will turn out to be deplorable if the ragged rope is wound around the flywheel of a working internal combustion engine: then the spring bursts, the pulley will tear off. But such cases when a complete replacement of the starting node is required, they rarely occur. In most cases, to fix the mechanism, it is enough to put a new spring or replace the cord.

Removing and disassembling the starter, replacing broken parts

To repair the starter of the trimmer for the grass, you will need to disassemble it first, and then collect it. This process is not a particularly difficult occupation. For work, you will need a screwdriver with the tip of the desired shape.

Everything should be done carefully, observing safety precautions, mainly that the spring does not injure the master if an accident.

Parsing the starting node

They disassemble the launch mechanism in order to install new parts instead of broken in the following sequence:

  • spin a screw with a screwdriver, fixing the pulley with a starter lid;
  • take out a spring and antennae;
  • Remove carefully with the pulley (you need to unscrew the head or work, having dressed the glasses and gloves before);
  • determine why the launch mechanism has broken;
  • If the spring collapses almost completely, then it is replaced;
  • When the spring exits from the hook, it is installed in the original place, bending the antennae before this (the photographs show the laying process);

To change the spring, you should work carefully and accurately: it can, under the influence of the effort caused by the installation of it in place, accidentally burst. Even if you carefully remove the video, then the spring strip flies very quickly from the coil and can injure your hand with its sharp edges.

Immediately putting a springy plate in the same place does not always work. It often slips, so attempts are required to repeat until the desired result is achieved.

Starter assembly

The assembly of the starting node is carried out in a number of stages:

When making the stated manipulations, it is necessary to lay two goals. If this is not done, then the spring over time damage the plastic cup, and when it is pulled. Because of this, a feeling appears, as if the spring had flown. To eliminate such a drawback, you need to install this part of a larger length or an additional goal.

When such spare parts are absent, you can just unscrew the screw a little, and the starter knot will begin to work without shaken. But this option is temporary. it is better to repair qualitatively as quickly as possible.

Spring tension

After installing the spring, it should be pulled. The following actions are performed for this:

  • Remove the handle from the starter cord;
  • Then the rope is inserted into the coil groove;
  • They stretch the spring, rotating the coil in the direction opposite to the clock of the clock arrow (reviews);
  • make the desired number of revolutions specified in the instructions for the use of the trimmer model used and the corresponding length of the cord used;
  • At the very end, the rope is threaded into a hole designed for this, located in the starter cover;
  • put the handle in place, fixing it with a node.

If after the repair the spring continues to fly, then you can get rid of this in the following ways:

  • Squeeze the suitable piece of the plate into the groove at the location of the spring hook;
  • drill holes on two sides of the groove in the coil, into which the spring hook is inserted and fix it using a wire.

Replacing a torn cord

A torn rope is replaced in the following sequence:

  • The old cord is removed;
  • choose a suitable rope (thickness and length);
  • Having reached it through a special hole in the coil, a knot is tied;
  • Sprinkle a spring, producing the required number of revolutions;
  • Fix the pen.

It is better to stretch the spring plate along with the partner so that the edge of the cord does not hit the starter mechanism.

It is easy to assemble a starter on a trimmer and wound a spring, only you should do it carefully and with caution. For different models, the gas tanks of the launching mechanisms are the same, so they are repaired in a similar way. In this case, there are some nuances associated with their constructive features.

Rules for working with raw weather

The gasoline tool is operated in any climatic conditions. Internal combustion engines tolerate well humidity, so they work flawlessly even after rain. Please note that during a rain for most trimmers, operation is prohibited. Manufacturers indicate this in the equipment passport.

Electric motors are more vulnerable to moisture than gasoline. If the motor is located at the top, then the probability of wetting is reduced. With the help of motorcycles, you can perform mowing herbs in a humid state, but it is definitely impossible to work during the rain. When water enters the extension cage, a short circuit or sparking occurs on the network, which leads to a breakdown of the tool. There is also a probability of current operator damage.

How to mow grass with a trimmer in areas with different relief?

During the summer season, it is recommended to regularly clean the air filter, control the condition of the cooling radiator. Polluted elements lead to engine overheating. Inspect the tool for visible damage, follow the service and repair schedule, and then the trimmer for the grass will last you for several years without fail.

The online store “Khoznovysh” offers to order a lawn mower through a website catalog with a quality guarantee. We will provide a detailed advice on the assortment, help make a choice. To do this, call us 7870.

How to start a motorcycle

The peculiarity of any technique with a two.stroke engine is a hard algorithm of cold launch, which must be strictly observed.Good afternoon, dear subscribers and guests of the channel.

The other day, a man asked me to see his mower.

The complaint was that the tool would not start. The client said that he bought a mower recently, worked only once. An attempt to start a motorcycle for a second time was unsuccessful.

Such leaks indicate that the mower shifts fuel, but the user practically did not work, and as I later found out from the client, they appeared during an unsuccessful launch.

Now everything fell into place. This lawn mower is completely serviceable, but the client would not be bad to read the instructions, especially the section in which the process of “cold” launch is described.

The result of proper run.in a gasoline trimmer for grass

After you have been running the lawn mower by the instructions, as a result, we get a tool ready to work. Of course, it is best not only to read the stages, but also to see the crowding on the video from specialists. The result of the correct actions will be obtained:

  • trouble.free operation of the benzo tool for a long time;
  • high.quality start of the device and stability of the submitted power;
  • lack of unforeseen repairs of a trimmer for grass after high.quality pounding;
  • Lack of overheating.

In this regard, the primary processing of the Chinese braid for grass is an integral part of the quality work of the device that can work flawlessly using benzos knives or cutting fishing lines of different diameters when processing territories available in the special store “Spit for grass”.

Modeling recommendations

Do not immediately, filling the mixture, go into a difficult fight with thick vegetation. It is necessary to start with the run.in, which will help to develop moving parts to each other and strengthen the skills with the device.

  • Do not immediately run the engine for maximum speed. It is best to dwell on the maximum torque moment.
  • Overheating is not allowed. However, you can’t mow on an unheated engine too!
  • The engine cannot be overloaded. The throttle should be opened by 2/3 of the course.
  • After running in, the oil drains.

These rules will allow an increased lubrication of parts of the piston group, which will become a guarantor of a long operation of the entire device.

How to properly serve a motorcycle

The device consists of the following mandatory elements:

Trimmer care involves monitoring the technical condition of each of them.

Engine care

When caring for a gasoline engine, it is worth paying special attention to the cleanliness of the air filter. it should not have sawdust and dirt. Foam filter should be constantly moistened with oil. Check should be carried out weekly, quickly change the filter as necessary. Before starting each work, you should check how the nuts and screws are tightened. It is also necessary to clean the muffler and candles from the carbon fiber as it is contaminated.

In the electric version, it is enough to follow the operating time prescribed by the manufacturer.

Serving cutting discs

If we talk about disks, then you should focus on how carefully the facets of the blades are sharpened. The sharpening should be carried out correctly, otherwise such a disk in the work will load the motor, which will only reduce the resource of the latter. A regular coup of bilateral discs should be carried out 180 ° for uniform wear.

Monitoring of the condition of the fishing line

How to care for the cordial part? The most important thing in this case is the use of a specially designed mowing fishing line.

What Is Biomass?

In no case should you replace the fishing line for a trimmer with metal cables or wire. this is traumatic.

  • The fishing line for the trimmer must be periodically changed;
  • The diameter specified by the manufacturer is set;
  • Winding of the cord goes tightly, but without the intersection of the turns;
  • The head must be constantly cleaned of dirt and regularly lubricated;
  • Carefully monitor the degree of wear (otherwise the gearbox or shaft is deformed).

How to monitor the corner gearbox

The priority task of the user is to prevent the accumulation of dirt on it. This circumstance will not allow the details to cool normally. The second requirement is to use consistent lubricant (such as Husqvarna or like), designed for a reducer pair. Usually enough annual lubrication procedure.

What you need to know about the casing to protect

It is forbidden to work without a protective casing. initiative can be dangerous for the user and others. But it is impossible to select such details from among the non.violent, it is necessary to use the recommended by the manufacturer. Damaged casing should be changed in a timely manner.

Casings can be attached both on the bar and on the gearbox. In universal models (working and fishing line and disk) two different kokhuzha are attached. A special cutting plate that cuts off the excess cord can also be located on the “forest”.

We summarize what has been said about the main points of departure in this maintenance of the Hitachi brand Motokos:

Serious technique: storage of cultivators and motoblocks

A large number of details and not the complete accessibility of all parts of this technique does not always allow a full preparation for winter storage, but it is necessary to do several stages of preparation:

  • First of all, it is necessary to prepare the engine. After the fuel is merged and the remains are developed, you need to change the oil while the engine is still warm.
  • We clean the filters: we update paper, my foam rubber, dry and soak in machine oil. We clean the fuel filter.
  • The spark plug must be cleaned, dipped in gasoline. While it dries, fill the oil into the cylinder and distribute it using a thicket of shaft. After wrap the candle back.
  • The engine and muffler are thoroughly cleaned of contaminants. The gearbox should not be cleaned with metal scrapers, you can damage protection and get consequences in the form of rust. It is better to use wooden devices, washing all the elements. After contacts of parts with water, they need to be dried;

The 3.96 BN Renewable Energy Project

Where to store: options and necessary conditions

Sarai or equipped housekeeping block is on the house territory of almost every summer resident. These storage places are the most common. The main conditions for storage of gas technicics in sheds or utility rooms are low humidity and stable temperature without sharp jumps.If the room is insulated, it will be an additional plus.

Another place for storing benzotechnics is a garage. Do not place the equipment close to the car, and also, by suspending it, you need to make sure that in the event of a fall it will not touch the car.

This method is not very popular in the countries of the post.Soviet space. But if there are no other options, find the company that provides these services is possible.

What you should pay attention to:

| Denial of responsibility | Contacts |RSS