Can an impact drill drill drill drill into concrete?

Step by step drilling process

Consider how to drill a brick wall with an ordinary drill. But the latter must necessarily have a percussion mechanism. Because without it, the tool will quickly overheat. And this is highly undesirable, as it will lead to early wear and tear.

Can you drill with an impact driver?

The power of the drill should not be less than 600 W. And the speed of the drill. above two thousand revolutions per minute. It is believed that the more this figure, the better. This is partly true. And for professionals, the priority is a tool that has a smooth speed control.

Before drilling, make sure that the process does not disturb any communications, in the form of electrical wiring or water pipes. If there is no paper plan of the location of the latter, you must use a portable metal detector. The device is able to indicate any iron, which is located no deeper than one centimeter from the surface.

Detailed instructions on how to drill a brick wall:

  • A marking is put on the surface.
  • By punching the core cutter at the desired point, an indentation is made, which will help to fix the drill in a straight position.
  • In the planned place, the tip of the nozzle is installed.
  • Keeping the drill straight, start the drill at a low RPM.
  • While gently pressing on the tool, gradually increase the speed of rotation, gradually bringing them to the maximum.
  • The process is periodically interrupted to cool the cutting part of the drill.
  • The operation is carried out either until the tip of the nozzle comes out on the other side of the wall, or until the desired depth of the hole is reached.

Throughout the entire process, the position of the drill must be checked. Its displacement from perpendicular can lead to drill breakage. And if it is necessary to make a through hole, the tool must be long enough.

Selecting the power for the drills

When drilling concrete, it is best to use a device with power from 600 watts and 2500 rpm. In order to choose the speed more accurately, you should read the recommendations of the drill manufacturer. The crumbling method is used to drill out the concrete, which does not require large revolutions.

impact, drill, concrete

Bosch PSB 650 RE impact drill

How to drill a concrete wall with a hammer drill

How to drill a concrete wall with an ordinary drill?. This is the question many craftsmen used to ask when they had to hang shelves, cornices and other.

Concrete is a durable material and therefore lends itself to drilling extremely bad. Even how to drill a wall in a panel house, the task may seem unsolvable.

Although, if you know certain secrets, this process can be greatly simplified.

Choose your tool

So, the first question a home handyman should ask himself is not how to drill a concrete wall with rebar, but with what. The main helper in this case will be a peorator, because it is designed for stone and concrete. At the same time, even powerful drills can not cope with a wall width of more than 12 cm. Although if we are talking about foam concrete, it turns out it is preferable to drill, as the peorator will simply break it.

The quality of the drill bit also determines whether or not you can drill a hole in a concrete wall.

One of the best options. to use drill bits designed specifically for percussion drilling. Their working part is a plate made of hard metal. With these drills, the question of how to drill a thin concrete wall can be considered solved.

There are also ring drills that have a diamond coating. They are very strong, they are used in special drilling rigs, so they cost quite a lot. Because to solve their problem, how to drill a hole in a concrete wall at home, it is impractical at least.

See also  How to disable the impact mode in a drill

Using drill bits

It is often necessary to get a large-diameter hole in the wall for the socket. How to drill a load-bearing wall in this case? Then use core bits, which have metal tips on their circumference. The crowns come in a variety of sizes, but the most popular are 68-centimeters, which are designed just for the sockets. When working with these parts, the impact mode must be turned off.

There are also drill bits for drills. But they have a different kind of plating. of cobalt-tungsten alloy. Use them conveniently, as drill a hole in the wall of concrete and simultaneously make a hole in the tile she is quite able to. Such drill bits are used only with powerful drills.

Drills. another device than to drill a concrete wall. Their diameters are varied. Experienced craftsmen advise to make a selection based on the diameter of dowels.

Drilling concrete peoratorom

So, how to drill a hole in a concrete slab using a peorator? The procedure is not complicated:

  • The drill is switched to percussion mode, and then the drilling begins; the tool must be held strictly at right angles;
  • after some time the drill bit is moistened with water, this will help to avoid overheating;
  • After you have succeeded in drilling through a reinforced concrete wall, the drill bit must be removed without turning off the machine itself;
  • To clean the resulting hole of dust, the drill is run into it several times.

It is not possible to drill the wall? The drill bit hits something hard? So, you need to try to make a hole in another place.

Do it with a drill

How to drill a concrete wall without a torch? The question of using a regular drill to work with concrete remains unsolved. So whether you can drill through a concrete wall, everyone decides for himself. The tool can break, can’t it? Yes, and the procedure takes longer.

Drill a hole in the concrete with a drill is possible, if you use a special tool. a puncher. It’s easy to operate: put the sharp end to the place where the hole will be located, hit it several times with a hammer, and then you can start drilling.

In doing so it is important not to overheat the tools.

As soon as the drill bit hits an insurmountable obstacle, you need to activate the punch again until the desired goal is reached. Here’s how to properly drill a concrete wall with a drill. Although it takes more time and effort, if you don’t have a torch, you can use it too.

Diamond drilling

Another easy way to drill through a concrete wall. However, only professionals with special equipment (high-powered electric motor and the like) use it.

How to drill a stud wall? No problem, because diamond drilling makes it possible to drill holes of large diameters and depths. and without irritating dust. Water is pumped directly onto the drill bit so that it cools down. As a result, the holes obtained have a neat appearance, and the appearance of cracks is completely excluded.

How to drill through tiles without cracking? see here. What is a drill jig for drilling holes? Read this article.

Drilling of concrete walls with this method is usually carried out by professionals of specialized firms. So it does not make sense to stock up on a diamond drill rig for independent work.

Read also:. for installing locks in metal doors. Oven repair at home. Repair of interior doors. Repair of plastic windows with their own hands. Shower cabin with their own hands from the tiles in the photo and tips for making. Door lock repair: how to do it yourself?

Diamond drilling is performed in 2 ways. dry and wet. In the second case, during drilling, water is constantly flowing onto the work surface. It cools the drill and reduces noise, dust settles in it. However, if there are electrical wires nearby, or permanent access to water is not possible, use the dry method.

Drill Masonry with an Impact Driver. Hex Shank Multi Material Drill Bits

Choice of drill bit

From the drill directly depends on the quality of the future hole. It will turn out neat and will not fall apart only if the drill was picked up perfectly correctly. It is recommended to use drills made of durable alloys, as concrete is a rather dense material. Other elements can easily bend because of the high resistance.

See also  The attachment on the drill saber saw with his own hands

If the drill can’t advance any further, it’s best not to continue. Otherwise even a sturdy drill bit will get damaged in the problem area. It is better to use a puncher or a perforator. They can help drill the hole further and then a regular drill can be used again.

Hammer Drill vs Drill | Which is Faster in Concrete?

How to make a hole in concrete

Concrete is characterized by high strength properties, which makes it difficult to make holes in the base. This is why it is important to choose the right tool and auxiliary equipment. Then you can avoid a lot of dust, destruction of the walls, and the work takes less time and effort.

It is not possible to make a hole in a solid base without destroying the entire wall. The only correct approach is to drill the concrete. For this purpose, manufacturers make several variants of removable tooling. selection is determined according to parameters of the necessary hole and power of used power tool.

Drill or drill

Such a drill is presented in the form of a rod. There is a shank on one side. This is the part that is installed in the seat of the power tool. The main section has a spiral-shaped notch and a groove for dust extraction. T-shaped working tip is a cutting plate made of hard alloys. On its characteristics depends the durability of the tackle and the quality of its work.

To understand which drill bit to drill concrete or drill, you need to understand the difference between the gear. It consists of the following:

  • The shank can be made as a hexagonal cylinder or with longitudinal grooves. Drills are suitable for the chuck of a drill, and drills (second) under the peorator and are marked as SDS.
  • The strength of the material from which the tool is made. The holes are drilled with reciprocating movements, which means that the concrete is subjected to a hammering force. The auger therefore has a higher hardness and wear index than the drill.
  • The drilling tool has a special groove in the main part of the rod to divert mineral chips from the hole.

To drill a hole in concrete, manufacturers supply three types of tools to commercial sites. They can be designed for rotary, reciprocating or combined. Accordingly, the safety margin of the latter parts will be higher than that of the former.

The tungsten carbide tip of the drill bit can be pobedite (tungsten-cobalt alloy) or diamond.

In a drill, only the first option is possible, because diamond is a fragile material. Depending on the parameters of the required hole, one of the three bits is used:

Drill bits are selected according to the type of shank and diameter. The size should be slightly smaller than the specified hole, so during the formation of holes the walls of the hole are slightly destroyed as the nozzle moves deeper into the wall.

It is also important to understand that you can only drill a hole in concrete with a drill of small parameters. This can be explained by the fact that the power tool mechanism is designed for rotary motion only. Peorator additionally performs the function of a baffle, so choose a drill for it.

The peculiarity of concrete walls is the presence of iron rebar. If a hammer bit or diamond bit hits it, it will quickly break down. Therefore, for such a case, you need to change the drill bit to one that is designed to work with metal.

Crown

For sockets with switches, ventilation routing with pipes need holes of larger diameter than for fasteners. For this purpose they use nozzles, which are called drill bits. The tool also has a drill bit, but in addition between the shank and the tip there is a hollow cylinder with a diameter of 30 mm or more. Its outer edge is the cutting element of the tool.

The edge of the bit for concrete is equipped with special hard teeth. Their performance depends on the quality of work, the speed of hole formation and durability of the nozzle. Based on this there are three types of tools:

  • Pobedite bits are used for impact drilling holes of diameter from 20 to 100 mm. Material fails when exposed to temperature fluctuations, so it is acceptable to work only in dry mode. In case of contact with reinforcing steel, chipping of the tip is possible.
  • The tungsten-carbide bit has a reinforced coating. This bit is designed to make a hole in a concrete wall without a torch. The nozzle accurately copes with brick and tile, so it is used for work with tiled bases. often such bits are sold in sets with interchangeable inserts of different diameters. There is only one disadvantage. the tool fails because of the metal.
  • The diamond edge is used to work with a hammerless or percussion drill. Acceptable dry drilling method and with periodic wetting. The face of the bowl is divided into segments, which are coated with diamond dust or chips. It is not afraid of metal, practically does not form chips and has a high working life. The latter is relevant for the formation of many holes.
See also  How to attach the painting to the wall without a drill

Features

Concrete structures are characterized by high strength, so it is quite difficult to drill them yourself.

This is due to the fact that rubble is used to create concrete products, and when during the performance of drilling, you get on it, the process is greatly hampered.

The need to drill a concrete wall arises quite often, it is necessary for the installation of shelves, cabinets, air conditioning, wallpapering, lighting fixtures, when attaching insulation or during plastering walls to fix beacons.

To solve this problem, there are several ways:

To make holes with a large diameter or to cut through a doorway, diamond-coated ring drills are used. To use such a tool, you need to use special installations, they allow you to make holes with a diameter of up to 250 mm.

Since the cost of such equipment is high, it is easier to hire professionals or you can rent it.

Choice of tool and work with it

When choosing a tool to drill a hole, you should understand that your job depends on it. A good drill accurately drills a concrete wall, or other necessary material, simplifies the process of drilling, while a bad drill will require a lot of time, may not cope with the task, or complicate it. What you need to pay attention to when choosing a drill:

  • Can the drilling speed be changed??. This point is important because adjusting the speed setting will ensure that the drill works accurately, helping it not damage the surface.
  • Is there a possibility of percussive drilling and depth adjustment?. Impact drilling can be used on problematic areas by softening them.
  • Can the core drill be held with both hands?. A drill is not a light instrument and for this reason, preference should be given to models that are equipped with handles.
  • Is the power of the tool satisfactory for your work?

Once you have decided on a drill, you have to get the hang of it before you start. Hold the core drill in one hand like a pistol and put your other hand on the tool’s handle (if it is not designed for a handle, put it next to the chuck). It is necessary to hold the drill strictly horizontally in the hands, so that the hole is not obtained with skewness and at the wrong angle. Wait until the core drill has reached ambient temperature before starting it up. Dramatic temperature fluctuations can cause condensation. If you decide to rest during work. unplug the tool from the mains.

Can an impact drill drill drill drill into concrete?

Each of us has repeatedly encountered the need to mount various objects on the walls, which add variety to the interior, create comfort, or simply remind of pleasant moments of life. Most often it is necessary to mount lamps and sconces, pictures and photographs, mirrors and shelves, to install an air conditioner or a TV on a concrete surface. If in the case of a small painting or a picture you can do with hammering a nail into the wall, then when the question is about more massive and heavy objects, there is a question of drilling holes. To avoid misunderstandings when working with concrete, for example, drill bit breakage, blunting of the same, it is worth to prepare the partition competently, choose a quality tool and correctly select the drill bit.

| Denial of responsibility | Contacts |RSS