Can I cut the laminating foil?

Can I laminate paper with an iron? Lamination of paper: heating plastic at home. Can I cut the film for laminating

Turn the laminator on, let it heat up and wait for the ready light or buzzer to beep. Carefully place the document in the opened laminating bag. Leave a reserve of film around the edges to ensure a secure bond.

Only feed the bag/film into the laminator with the sealed end first. If the film is mis-fed and fed with the loose end, there is a high chance of warping and jamming the document.

After laminating is complete, lay the document down on a table and let it cool for 30 seconds to help keep it flat.

Fellowes recommends not using films from other manufacturers especially from unknown Chinese producers because of high risk of laminator damage and breakage. The cheaper films save on the PET base and use more glue to keep the thickness of the film. During lamination the excess of adhesive comes out from under the film and falls on the laminator rollers that may lead to further winding of the film and jamming of the laminator. Only a service technician is able to restore the laminator’s functionality.

Different temperature settings are used for different film thicknesses. The thicker the film the higher the temperature needed for gluing. Home laminators can have 1 universal temperature setting for films 80. 125 µm. The quality of the lamination is good in this case, but ideal results are achieved when a different temperature range is set for each film thickness. Advanced laminator models can have 1 temperature mode and the film heating can be adjusted by changing the lamination speed.

Cold lamination is designed for materials that may be sensitive to high temperatures, such as antique papers or photographs. In this case the laminator rollers are not heated but the film is glued due to the pressure of the rollers on the film. The laminator should be equipped with a special mode for cold lamination.

Cold lamination films are used in very rare cases and are therefore not popular, also because of their high price. You can use films from other manufacturers for cold lamination.

The laminator can be cleaned of excess glue, dirt and dust with the special Cleaning Sheet fs-53206. At the end of the day you just need to run the cleaning sheet (without film!) in hot lamination mode. The sheet will absorb dirt and adhesive residue from the rollers. If necessary, the cleaning process can be repeated several times.

If there is no peel-off sheet handy, a normal folded sheet of paper can be used. Insert into the laminator with the folded side facing forward.

The lamination process is irreversible. a document cannot be taken out of a sealed film. The document itself tears when peeling the film. Be careful and cautious when adjusting the laminator and choosing the film. We recommend that you always pre-laminate sheets of paper/ drafts that are of no value.

Check the temperature setting of the laminator and run the document through the laminator a second time. Always use an original film for a consistently high lamination result.

The film for lamination should be chosen according to your task. 80 μm film provides basic protection against dust and dirt and makes the colors of the document more vivid. 100 and 125 μm film offers better document protection including protection against premature fraying. 175 and 250 micron films offer maximum protection and give the document extra rigidity.

Please note that laminating higher weights in 175 and 250 micron films requires a laminator with the proper temperature settings.

For the right laminating film please use the online film guide.

Each laminator has been designed for a certain daily workload. Entry-level laminators, for example, are designed to laminate up to 10-20 documents a day or even a week. Based on this kind of workload the reliability of the drive and heating system is calculated. Simple laminators can handle more, but their service life will eventually be reduced by several times. For high lamination volumes it is preferable to choose an office laminator.

On the one hand a simple entry level laminating machine with 1 temperature setting will do for laminating 80 microns film. But 100 sheets per day would be too much for this laminator as its mechanism is not sized to withstand the intensive use of the machine. We therefore recommend choosing a laminator paying attention to the size of the office and the recommended load first of all. In our case, these will be models designed for intensive work in a large office. Neptune 3, Jupiter 2, Venus 2. In addition to increased reliability, they have higher lamination speed. The Venus 2, for instance, operates at speeds of up to 110 cm/min and lets you laminate an A4 sheet in 17 seconds, which is three times faster than conventional models.

External heated rollers are considerably cheaper and are used in low cost laminators. The rollers are heated by an electric spiral affixed inside the laminator body. Internal heating rollers, as the name already implies, are heated from inside. Internal heating rollers have a constant temperature over the entire surface of the rollers, which means that the quality of the lamination will be perfect over the entire sheet area. Because of the high cost the internal heating rollers are only used in professional models of laminators.

Batch laminators are easier to use and are better suited for everyday use in the office. This laminating machine is designed to laminate into packages (2 films with an adhesive layer, sealed on one side). Sacks or film for lamination may come in several formats, such as A3, A4, A5, A6, etc. No special skills are required to operate such laminators.

Bundles for laminating are most commonly referred to as laminating film.

In a roll laminator the film is fed in rolls. Laminators are designed for professional high volume lamination and require a trained, qualified operator.

Is it possible to laminate a document at home??

With clear instructions, the document can be laminated at home, and, answering the most popular question, no, the resulting paper will not differ from its counterpart made by a specialist. There are several ways to laminate papers at home, some of them require using external equipment and materials, others are extremely easy to perform and do not require significant cost. Let’s look at a few of the most popular ways.

See also  How to start a STIHL fs 55 brushcutter

How to choose a film for laminating

There are many kinds of products for lamination, which differ in manufacturing method and application, thickness, composition, format, etc. To choose the right one, it is worth considering each criterion:

  • Thickness. Laminating consumables are available in thicknesses from 20 to 250 microns. When choosing, it is worth taking into account that if you plan to cover the file on both sides, then this indicator should be multiplied by 2. As a rule 75-80 micron thick films are used which provide normal protection of documents against moisture, dirt. reliable against mechanical damage will be coating with a strength of 100-125 microns. For creating a hard layer (on signs, badges, menus, etc.).) use consumables with 175-250 microns thickness.
  • Size. As a rule, sheet formats A3, A4, A5 or A6 are used, and the package must be slightly larger than the document itself to allow the film to seal around the edges. An optimum allowance is 2-4 mm on each side to achieve a good sealing. If you need to laminate a non-standard size document, consumables of the nearest bigger format should be chosen and the excess of material should be cut off along the edges after finishing processing.
  • Invoice. Gloss enhances colors, giving documents brightness, so it is ideal for drawings, photos, presentation products. A mat cover makes the picture softer, removing glare.
  • Laminating method. Cold method is in demand for those documents that can lose their properties and integrity under the influence of high temperatures. In all other cases you can use hot lamination, because it is much cheaper and guarantees an excellent sealing.

How to laminate paper

wikiHow is a wiki, which means that many of our articles are written by more than one author. Volunteer authors worked on editing and improving this article.

Number of views on this article: 38 022.

When you laminate paper, you protect it from dirt, creasing, aging, and discoloration. You can either decide to laminate a very important document, such as a marriage certificate, or a document that you use frequently, such as a menu. This article shows you how to laminate paper, with or without a laminating machine.

Choose the right laminating machine for you. Mostly buy machines that are suitable for laminating a standard sheet of paper. (216 mm by 279 mm).

Turn the machine on and give it time to warm up. Most machines have an indicator light that tells you the machine is ready to use.

  • If the film is slightly larger than your document (for example, if you want to laminate business cards in special business card film)), you will need to carefully place your document in the center of the film so that you have an even edge all around.
  • If your document is much smaller than your film, you don’t have to center it, because you can trim all the edges later.

Place your document film in the feed tray. The glued edge of the film should fit against the closed opening of the tray. There are two sheets of heavy cardboard there to prevent the glue from collecting from the lamination.

Place the tray in the machine. Feed the film with the glued end forward until the machine engages that edge. Don’t push the tray, the paper should pass slowly through the machine itself to bind the pages together.

Trim the edges, if necessary, with a paper cutter or scissors. Leave a minimum edge of 2 mm.

Buy a self-adhesive laminating sheet. The best one has a grid on the back side that will allow you to rearrange the paper if you put it down wrong the first time.

Remove the mesh to expose the adhesive side. Keep it around the edges so it doesn’t leave your fingerprints on it. If the foil has a grid, keep it to help you position your document properly.

Open the adhesive side. Lay the film on your work surface with the adhesive side up and the mesh underneath. You can use the grid you just removed from the tape, or a sheet of lined paper, or a grid you drew on a regular piece of paper. Attach this mesh to the table so it doesn’t move around.

Put your document in the center of your sheet. If you have small sheets for large laminating film, it will be very important to align everything. You may have to move the film over the mesh.

Tape the rest of the paper to the laminating film. Straighten your paper so it lies flat and there are no folds or bubbles.

Put a second sheet of paper on top of the first. Start at one corner and gently flatten the paper to remove all creases and bubbles. You can also use a device such as a roller to straighten a sheet of paper, or a credit card can help you.

What you cannot laminate

Do not use hot lamination for documents that are afraid of heat, such as receipts from cash registers, ultrasound photos. Such documents turn black when heated in the laminator, which means that everything that was on them will be gone.

laminating, foil

For these documents there is cold lamination, which does not heat up and only bonds the plastic film through pressure in the laminator.

laminating, foil

You can laminate any documents in this way. The only question is how.

Keywords: lamination printing, cold, hot, laminate document, unlaminate, image on paper, can you laminate, printing, Why use lamination, all the secrets of lamination

Hi all. I want to share my experience that I bought half an hour ago. I firmly declare that the documents can be de-laminated easily enough.What you need to arm yourself to do this procedure 1) Heat Gun (I do not know how this tool is called in Russia), but it looks like a drill and instead of a drill bit nozzle which emits hot air. the temperature needs to be higher than a normal hair dryer. 2) A long knife with a blunt end. 3) And patience and free time, the process of cleaning a document the size of A4 took 3 hours. If you start speeding up the process there is a big chance that you will ruin the document. Sync by honeybunny. My wife received her U.S. citizenship two days ago and was given a Certificate of Naturalization, the most important document. which must be countersigned, without which it is invalid. She forgot about the signature and laminated it, and then went to send the documents for the passport. That’s where she was in trouble. The documents were not accepted for two reasons, no signature and laminated document is not valid 😯 She ran back to where she laminated but they said that there were no options, the film has an adhesive that is soldered to the paper when heated:oops: She went home in tears because in a month we have to go on vacation and to restore the certificate will take at least a year. The car is great, but it needs a skilled care: Well, I started to go in with my own two hands:roll::lol:The procedure. First I put the glass as a flat surface to work on. Trimmed the edges of the film evenly around the edges of the document. Then started heating from the corner

See also  How to cut a window in an aircrete wall

When the plastic became soft I very carefully began to stick the knife between the front side of the document and the plastic. The plastic started to peel off nicely without damaging the paper

This procedure is done without haste. The Neat Gun I use has two positions. one very hot and it burns the plastic immediately. And the second is considered weak, but at this position it also melts the plastic. So I had to experiment with the distance

It is very important not to overheat the plastic. Because it hardens after melting and crumples the document in places that have not yet peeled off

When the film was completely removed, there was a layer of glue on the paper, which I cleaned with the same heater and scraper:-P After the procedure, the document looks like it has never been laminated. I hope my advice is helpful to someone. good luck everyone.

How to choose a film for laminating

The selection of the material that will be used to protect the documents in the future is an important process. A quality lamination film should have:

  • High transparency and adhesion;
  • Ability to withstand UV radiation. this is important if you do not want laminated documents to fade over time from exposure to sunlight.

The type of coating (glossy or matte) is chosen depending on where the documents will be used. If you need reliable protection against moisture, choose a thicker material.

In the selection process you must also take into account what kind of film for laminating. Look at the composition and labels provided by the manufacturer. This will help you determine whether you are laminating with cold or hot sheets.

Laminating process

Sooner or later, many people wonder how to laminate paper. It is not difficult, you just need to prepare everything you need and follow a few simple steps.

To laminate the paper at home, you need to have :

What to do if you have decided to laminate paper?

  • . It can be batch or roll. In roll-to-roll laminators, a sheet of paper is rolled up into the film, which is fed from the rolls at the top and bottom. After completion, cut sheets of the required size. Can be matte, glossy, textured.
  • Everything from children’s drawings to documents can be laminated. If you want to laminate a document, first think about whether it is necessary. Not every official or notary will be willing to accept the laminated document. There is no direct prohibition on accepting such documents, but authenticity cannot be established under laminated paper, and the law requires working with originals. In addition, laminated paper cannot be stamped or marked.
  • Place the sheet to be laminated on top of the connecting tape. On the side that will be separated, make a mark, leaving an allowance on all sides. Cut out the resulting piece. Then make another one of these same marks.
  • Now you separate the tape from the backing paper and place it with its adhesive surface up and in the middle of the document. The paper should lie flat.
  • Separate the second piece of tape from the paper. Place it with its sticky side down on the object to be laminated. Be careful not to spoil it.
  • Place the document in a laminating bag and drop it into the laminator The latter retracts it and outputs a ready laminated sheet.
  • The film has adhered to the sheet of paper. now they form one unit. The document is reliably protected from negative external influences.

To laminate the paper means to cover a sheet with a film. This is to protect it from soiling, moisture, or rapid deterioration.

Special workshops are engaged in lamination. You can use their services if you need to laminate some important documents.

However, in everyday life we often have to solve the problem of preservation of some printed materials. It can be photos, textbook covers, all kinds of cards for the child’s development. In most cases, you use a wide adhesive tape, but it’s not aesthetically pleasing. You can see the joints, the slightest mistake. and it is impossible to correct the resulting folds.

People craftsmen have adjusted to laminate the paper at home. First of all, you need to prepare everything you need. You will need film and an iron. The iron is in every home, but the film will have to buy, and it is not very cheap (the price depends on quality), but it will be much cheaper than in the studio, in addition, you get pleasure from the process itself.

So we choose the film. It’s not sold individually, but in sets. Sets differ in the number of film sheets, their size and thickness. The amateurs believe that the format of A-4 is the most optimal. and the thickness of the film is better to take thinner. 75-80 microns. Of course, thicker film is more durable, but it also costs more. In order to save money, thin paper can be glued to cardboard and then laminated. The price range of films also varies depending on the manufacturer, but here everyone is guided by their finances.

Each sheet of film is a The inside of the film is coated with a layer of glue. This is the side on which it is glued to the paper, so it is important not to mix it up. Don’t be embarrassed by the fact that the film is matte.

You have to get the hang of heating the iron. It should be hot enough to stick the film but not so hot as to deform it.

When the iron is hot, put a sheet of paper or a photo in the and start ironing the film from the end where it joins together. There’s no hurry. It is necessary to gradually expel the air. The frosted film will become transparent as a result of the temperature. It becomes much stiffer when it cools. Sometimes it is recommended that you iron the film over a piece of paper. But it is not necessary, a moderately heated iron does not stick to the foil unless of course you mix it up and put it on the other side.

See also  Hydraulic press with electric drive with your own hands

At first, when there is little experience, there may be an air bubble under the film. Don’t try to peel it off and redo it. The situation can be saved in a less radical way. Put a damp cloth over the foil first and try ironing again. If this does not help, then carefully pierce the bubble with a needle and iron it again. As a rule, the film will straighten out perfectly and the puncture will not be visible.

When your piece is hardened, you should cut out laminated cards on a special liner. It is better to do it not with scissors, but with a metal ruler and a mounting knife. If you want to round off the corners, use a pair of nail scissors.

Another advantage of laminating with an iron rather than a laminator is that you can laminate only one side of the paper if you want to (this is often done in order to save money). This method is usually suitable when laminating thick cardboard and only one side has an image. Then carefully separate the two parts of the film and apply it only on one side of the paper. So half as much film is used.

Laminating paper at home to do yourself is very easy. In the stationery department, I bought a hot melt film for only 25 In a roll of 1.5 meters of film, this amount is enough to laminate a fairly large amount of A4 paper.

  • thermal adhesive film
  • scissors
  • white A3 sheet of paper
  • And the paper or documents to be laminated

What do you need the film for laminating?

With the help of this consumable material can significantly improve the appearance of promotional products, business cards, posters, calendars, packaging, covers for books and pamphlets. Paper lamination can extend the shelf life of a wide variety of documents. The film for lamination has these positive qualities:

For different tasks there are different types of films which differ not only in their thickness but also in their texture. The ratio of the thickness of the adhesive to the polymer layer determines the stiffness. If the polymer layer is thicker than the glue layer, the film will be hard, and if vice versa. soft. Either type of coating gives the product a more spectacular appearance. Depending on the method of processing there is a film for cold lamination or for hot. An important indicator is the texture of the film.

Matte film for lamination

This coating practically does not give glare, it is used if the image will fall on the directional light. Matte laminating film allows to draw on such a surface a pen or a pencil, and traces of it can be removed with an ordinary eraser. Scratches are less visible on this film, but it dulls the color, and the picture underneath loses its contrast. It is often used in promotional products.

Glossy laminating film

Such a film, on the contrary, enhances color of any image making its shades brighter and more saturated. Products coated with a glossy film have a smooth, pleasant to the touch surface. However, this lamination film produces glare that makes it hard to see fine details and makes the text unreadable. In addition, scratches can occur on such a coating.

Texture laminating foil

There are several varieties of film, which differ in texture: in the form of leather or linen, in the form of goosebumps, sand or frost patterns, with a holographic effect, and so on. Scratches are hardly visible on textured surfaces. This film-billet for laminating can be used in decorating the surface of any image. Textured film is used in the manufacture of stand photo panels for various exhibitions. This lamination film is the most expensive.

What to replace the lamination film?

If you have no special film at hand, you can use for laminating these improvised materials:

  • File. Use scissors to cut the side edges for filing. Insert the desired sheet into the file. On the bottom and top edges of the file glue strips of wide tape. The laminated document is ready, you can attach it to the wall and so on.
  • Wide tape. Some documents can also be laminated with it. Cut strips of tape to the width of the product (with an allowance on both sides) and accurately glue them one by one, carefully smoothing them out. After pasting the whole sheet of paper, fold the excess tape over the edges to the back of the item. This option is best used for laminating small documents.
  • Self-adhesive film for laminating. On its outer side there is an adhesive layer, covered with a special strip. It is necessary to cut the film to the necessary size, remove the base, and, having laid it on the paper with the adhesive side, smooth out the surface well. This self-sticker can be both sheet and roll.

Scrapbooking. almost all masters who are fond of needlework know it. This unusual type of creativity originated in England as a decoration of personal diaries. Now all over the world in this technique decorate photo albums, postcards and other products.

Weaving from newspaper tubes. a hobby that has recently enjoyed great popularity. It originated in the East and has taken over the world, because it is much easier and easier to handle paper than the traditional straw or vine.

Papier-mâché is considered one of the oldest and most accessible types of creativity. Such a mass can be made from old newspapers, napkins, toilet paper using different formulas of glue, and make both simple crafts and real masterpieces.

Mask of toilet paper in some situations, can be an alternative to the medical, which, for several reasons, can not be purchased at the drugstore. Such a product at a very low cost can be made in just a couple of minutes.

| Denial of responsibility | Contacts |RSS