Can tiles be cut with a glass cutter?

How to cut a mirror tile

For qualitative cutting of mirror tiles the best choice would be a diamond glass cutter. This is due to the fact that the facing material is similar in structure to glass.

Many craftsmen prefer to use an oil glass cutter with kerosene as a lubricant. The step by step instructions do not differ from the actions when cutting tiles. The material is broken, aligning the resulting groove with the edge of the table. The movement should be sharp and applied to the middle of the piece to be cut.

Mirrored tiles with facets are ideally not cut. It is selected in such a way that the parts are placed entirely on the desired surface.

Getting ready to work

Before you start cutting tiles, you need to prepare for work. In addition to the cutting process itself, it is necessary to clarify some points on the work.

Choosing a glass cutter

If you have settled on the glass cutter as your main tool for cutting ceramic tiles, there are three models to choose from:

By far the simplest and easiest to use is the roller-type glass cutter. A small roller (also called roller) as a cutting tool, provides a thin line of cut without chipping at the edges. A good alternative is the oil-type glass cutter, which has the same operating principle as the roller cutter.

Using a tile cutter to cut mirror or glass tiles

Only it is equipped with an automatic fluid-oil feed to the cutting mechanism. The oil is in the cylinder of the rod of the handle and gives lubrication during cutting, which makes the work much easier. Both of these models of the roller glass cutter do not require special training, a novice craftsman can easily cope with them.

The diamond glass cutter requires an “experienced” hand. Only a ceramic tile cutter with this tool should be used by a specialist who has firsthand knowledge of how to use it and has “adjusted” to the diamond cutter. Otherwise a lot of tile material will be spoiled.

Don’t worry if the edges of the cut are not as sharp as they should be. The uneven depth of cut can be caused not only by lack of experience and inexperience in using the cutting tool, but also by the poor quality of the ceramic material itself.

tiles, glass, cutter

In such a situation, a sanding paper (sandpaper) with medium or coarse grain, which grinds the ends of the cuts, will correct the situation, resulting in a perfectly smooth edge.

Additional tools

To make a quality tile/tile cutting you need the following set of tools:

Cutting Ceramic Tile with a Glass Cutter

  • The glass cutter itself (roller, diamond or automatic oil feed);
  • A marker to apply the cutting scythe, preferably water-based, so that the marking can be easily removed without leaving traces.
  • A metal square or ruler that is used to measure and as a guide when cutting tiles/tile;
  • A table with a stable horizontal surface;
  • Wooden bar (pencil) for lining the place of the break;
  • Medium and coarse sanding paper;
  • Protective gloves;

Nuances, advantages and disadvantages of cutting tiles with the glass cutter

Special mechanical tools and electric devices are much more convenient for cutting ceramic products than the glass cutter. But such special devices also cost much more. Therefore, if tile cutting is done at home with small amounts of work, it is more practical to use a glass cutter. After all, it is not at all reasonable to use expensive tools when only a few tiles need to be trimmed.

See also  How to increase the output of the compressor

The glass cutter has some advantages over other tile cutting tools:

But the use of the glass cutter has significant disadvantages:

  • it is not suitable for large amounts of work;
  • the tool is not able to cut through dense tiles;
  • there is a risk of damaging the tile.

The use of such a tool is not very convenient. The glass cutter has a small roller that makes shallow grooves. Therefore, you have to finish the tile by hand, which causes the risk of cracking the tile or break it unevenly. Because of these sequential procedures of marking, notching and breaking the entire process of cutting the clay plate comes out quite long and tedious. Therefore, it is not recommended to use the glass cutter for large amounts of work.

The glass cutter is also unable to cut through heavy-duty porcelain tile with its small roller. It is also unlikely to scratch a thick floor tile to the depth you need to break it. The tool is only capable of cutting thin wall tiles. Therefore, for large amounts of work or cutting powerful products, it is better to buy a special tile cutter.

Don’t miss: Preparing the floor for tile laying. instructions

Safety precautions

Before you start finishing work and, in particular, cutting tiles, you need to take care of your workplace.

The table or any other surface must be well secured.

Check working tools and the right equipment.

If the room is not sufficiently lit, you must use portable lights that operate from 12-42V outlets. Pay attention to cleanliness in the workplace. unnecessary tools and construction debris lying around underfoot can lead to injury.

tiles, glass, cutter

Workers must be provided with protective clothing and personal protective equipment according to safety standards. About this in more detail:

  • A suit of thick fabric. protects the body from possible cuts and injuries when working with the cutting tool;
  • Goggles. protect your eyes from splinters and dust. Glasses should be of plastic or unbreakable material;
  • Respirator. protects respiratory organs from dust generated when cutting tile material. This means of protection is used if there is a large amount of work.
  • Gloves. protect your fingers from getting cut by the sharp edges of the tile. In some cases rubberized ones are used, if the surface of tiled material is glossy or has been degreased.

When cutting tile material, you must be extremely focused and attentive, use the working surface, and not break the tile on the cutting line by weight or against the knee.

Compliance with safety rules, the use of protective clothing and personal protective equipment makes it possible to cut tile material without injury and with maximum efficiency.

How to cut tiles with a glass cutter?

Of course, to cut the tiles is not necessary to use a glass cutter, the following tools can also help you:

But here’s what to do if you don’t have anything but the aforementioned glass cutter?

Important! You should understand that you can’t cut 5 mm off a tile with a glass cutter, because you will at some point remove the tile by “breaking” it, and that’s hard to do when you have to separate 5 mm or less.

Next. in general, you first need to figure out if you can cut your tiles with a glass cutter. Earlier it was no problem, but now the manufacturers produce such a number of ceramic tiles, which will be difficult to cut, even if you have a hand-held tile cutter, and what to say about the glass cutter! Therefore, it will not be superfluous to practice on broken tiles. in general, whether the tool you choose will take your tile?

Features of cutting with a glass cutter

Of course, to cut the tiles is not necessary to use a glass cutter, you can help and the following tools:

See also  How to attach the snow ploughs to a single-axle tractor correctly

But here’s what to do if you do not have anything other than the aforementioned glass cutter?

Important! You should understand that you certainly can not cut 5 mm off the tile with a glass cutter, you will at some point take the tile to “break”, and it is difficult to do when you need to separate only 5 mm or less.

Next. in general, you first need to figure out whether you can cut your tile with a glass cutter. Earlier it was no problem, but now manufacturers produce such a number of ceramic tiles, which will be difficult to cut, even with a hand tile cutter, and what to say about the glass cutter! Therefore, it is not superfluous to practice on broken tiles. in general, whether the tool you choose will take your tile?

Possible errors

What can be the reason for the appearance of chips and marriage:

  • Poor quality of the sanding disc. cracks, damage, poor sharpening.
  • The cutting wheel is installed on the wrong side or is not properly selected. the thickness or height of the edge is low, the diamond layer is missing.
  • Mismatch between the blade of the roller and the planned line.
  • Insufficient fixation. in the process of cutting the tile vibrates and shifts.
  • The operation is performed in several steps, which increases the percentage of defects.
  • Powerful tools are used, quick, sharp movements, strong pressure.

The final result depends on the availability of special skills of the master and the correct selection of cutting tools.

Cutting porcelain stoneware at home is carried out with the help of various devices. Let’s talk about them.

Cutting Ceramic Tile with a Glass Cutter_ITRK SUPPLY

How to cut ceramic tiles with a glass cutter yourself?

Tile work at home. kitchen, bathroom, floor in the hallway Who of us has not encountered such tasks? What are the right tools for that?? What to cut a tile? The answer is simple. a handheld glass cutter. For small amounts of tile work, it is the ideal choice. Handheld glass cutter will allow you to implement all your plans to improve the interior space, while not driving into debt after a home repair.

Other ways to cut tiles

Although the glass cutter can be good for cutting tiles, it is not the only tool that can do this job. Below, we will consider a few more ways to cut a piece of ceramic tile with other devices, without using a tile cutter. So, what other tools can be used to cut tiles:

angle grinder

Pretty effective, but not the highest quality way to cut tiles. The saw blade is chipped and requires further work with emery paper. The work requires a diamond disc (not segmented), and, of course, an angle grinder.

The principle of operation is very simple. Lay the tile on a flat surface, mark the fishing line and make the cut, slightly leaning the disk against the surface of the tile. It is not necessary to cut through the tile completely, it’s enough to get an even groove and make a break in it. For less dust, before working, moisten the tile with a wet rag.

The drill

A very convenient way to cut round holes, by using special attachments on a drill or an electric screwdriver. There are 3 types of special bits: diamond drill bits, ballerina drill bits and regular drill bits for glass and tile. The most perfect cut and the highest price come with drill bits. Next in quality and cost comes the ballerina. Special drills are the cheapest, and they can be used to get any shape of cut, but it is necessary to sand down the edges with sandpaper.

If everything is clear with diamond drill bits and ballerinas, then regarding the tile drill there are sometimes a few questions. The principle of operation is as follows:

Saws

A budget and quite accurate way to cut tiles. Can be used for straight lines and shaped cuts. From the disadvantages it can be noted the low speed of work. All you’ll need is a hacksaw and tungsten carbide or diamond-coated thread.

See also  How to cut tiles without a tile cutter

Sawing tiles with this device is not difficult even for beginners finishers. Tighten the thread in the hacksaw and start sawing. If you want to make a circle inside the tile, then first we drill a hole in it, then we put a thread through it, fix it in the hacksaw and saw from the inside.

Jigsaw

Like the previous method is based on sawing tiles with a carbide blade. Has a fairly high speed, but can be used mainly for straight cuts rather than curved cuts. Electric jigsaw can cut a circle, but the chance of chipping tiles are many times higher compared to the hand saw. Special ceramic or metal blades are needed for the work.

To improve the quality of the cut and reduce chips, it is recommended to work at medium and low speed.

Before you start renovating your bathroom or kitchen with your own hands, it is better to know how to cut tiles with a glass cutter, because it is a very simple and cheap way. After all, to resort to the help of a master is expensive, as well as to acquire special equipment for cutting tiles. Therefore, with a small amount of work, it is better to do everything yourself and with a simple tool. The only thing necessary in this case. it is necessary to be careful not to chip the edge of the ceramic product with the glass cutter, and everything will turn out.

Can tiles be cut with the glass cutter?

The history of tile goes back many thousands of years. Suffice it to mention the fact that it was used to decorate the magnificent palaces of ancient Rome and Greece. Since then, craftsmen have mastered different ways to apply mosaic (the progenitor of tiles), creating amazing works on the walls of temples.

It is known that even then masters were able to properly manufacture and produce mosaics of a certain shape, but it is not known exactly with what tool they used for cutting them.

Only one thing is absolutely clear, the method of making a tile has not changed much over the centuries. Already today it is made of clay with the addition of sand and subsequent baking.

Glass cutter

Since tile cutter and glass cutter have a similar principle of action. to make a groove on the outer covering. the latter is often used in the absence of the former.

Glass cutter. a small instrument, resembling a pen, with a diamond-coated disc instead of a rod with ink. When working with it is also desirable to soak the tile in water for 30-40 minutes.

After this time on the outside of the tile should be marked with a pencil or marker, put a ruler to the resulting line and spend the glass cutter in one not very strong movement. Then you need to put a pencil or wire under the resulting groove and press the tile on the sides parallel to the cut. If you go too far with the pressure, you will get chipping on the glaze.

There are also oil glass cutters. Inside the “handle” there is a tank which is filled with a mixture of kerosene and machine oil. Due to this, a better slip is achieved, and therefore you get fewer chips on the enamel.

Such cutting is quite time-consuming, so it is not suitable for large volumes. Also, difficulties may arise when working with thick floor tiles. most likely, even breaking it evenly will not work, even putting a pencil under the marking.

| Denial of responsibility | Contacts |RSS