Basopiles flowing gasoline from the gas tank Partner. Gasoline in a chainsaw flows?…

The chainsaw oil flows out when it lies If everything is in order with the ignition system, then we go further and check the fuel supply system of the chainsaw. Disconnect the fuel hose from the carburetor and look, flows out of it fuel or not. Eliminate oil leaks on a chainsaw | Video on.…

Read More

Replacing the springs of the Champion chainsaw starter. The device of the chainsaw starter

How to wind a spring on a starter of the GAMPION Lawn Mushrooms In the rarest situations, the starter mechanism is broken with inaccurate operation of the tool. The consequences can be nasty: deformed cord wound on a flywheel of a working motor, tears the pulley, and the spring bursts. But these are isolated cases,…

Read More

Oil consumption for a chainsaw per hour. Merged containers

Chain oil consumption At least some two.stroke chatefering engine works on the consistency of gasoline with oil, respectively, on the property and the correct consistency of these components, it depends on how long it will last. Also in the chainsaws, the tire and the chain, and the quality of the lubricant is not the last…

Read More

How to disassemble the OLEO-MAC chain electric saw. Additional Information:

Trimmeres repair (benzos, electrocos) OLEO-MAC (OLEO-MAC) When buying a chainsaw, the carburetor has factory settings and adjusted to optimal operating modes. However, during operation, the engine (ICE), the fuel pump, the carburetor wear out, as a result of which they are required to carry out their repair, maintenance and settings. In this case, the role…

Read More

The chainsaw is started and immediately stalls. Saw and stalls

Frequent malfunctions of the Husqvarna chainsaw 236-240 If it is impossible to start the engine, it is necessary, observing the sequence, to perform the following actions: The location of the air filter and the spark plug. Check the presence of gasoline in a tank. Replace fuel if it was stored for more than a month.…

Read More

Chain saw does not twist the chain. The chain lubrication system

Does not twist the chain on the chainsaw of Husqvarna. The chain works but the chain does not spin. The final adjustment of the carburetor of the chainsaw Despite the simplicity of the construction of the chainsaw, if interruptions arose in its work, and sometimes with the complete failure of the unit, it is quite…

Read More

How to check the anchor of a chain saw. If there is no ohmmeter?

Checking the anchor for an interval circuit Electric machines consist of a rotor and stator. The stator is fixed windings laid in the case. An anchor is a mobile part, therefore, as a rule, particles of dirt and lubrication fall on it and an oxidized plaque forms under the influence of temperature. It can cause…

Read More

How many degrees is chain sharpening?. Mechanized sharpening on a machine

How to sharpen the chain saw blade with your own hands? If the blunt end of the saw blunts the cutting performance. You will report a lot of force, but you won’t get a good cut. And the risk of injury caused by a chainsaw with a blunt blade is greatly increased. There are various…

Read More

How to know the size of a chainsaw tire.

Chain marking for chain saws This is the defining parameter, and depending on its value, all existing chains are divided into five groups with 1/4”, 0.325”, 3/8”, 0.404” and 3/4”’ pitch.1/4″ (6.35 mm) pitches are typical for small chains mounted on low-powered single-handled saws. Chains in 0.325″ (8.25 mm) and 3/8″ (9.3 mm) pitch are…

Read More

How much oil to put in your chainsaw. Characteristics of Domestic Chainsaws

What oil to use for petrol cutters and chainsaws #short #like #shortvideo #shorts #top #trending What’s the right oil to gasoline ratio for a chainsaw? Hi there! This article is about the right oil to gasoline ratio for a chainsaw. This is probably the most important thing to know when operating this machine. Lack of…

Read More
| Denial of responsibility | Contacts |RSS