Cord -dressing in the trimmer head Champion. What is needed to replace the cord

How to install a fishing line for a trimmer coil for a champion grass

The main elements of the trigger is a mowing spike, which is a cylindrical case with a coil inserted inside (bobbin). A fishing line for a trimmer (cord) is refueling into it. The heads differ from each other in the method of supply and refueling of the cord. There are three types of heads in total:

  • Automatic. The fishing line is submitted after that, as the user reduces engine speed. Automatic supply of the cord is very convenient when you need to do a large amount of work. The minus of such a head is a large thread consumption.
  • Semi.automatic. The use of such a head does not require the user to perform any complex manipulations. The principle of its operation is arranged so that the fishing line for a trimmer begins to automatically lengthen at a time when a trimmer for grass works at full speed. It is only necessary to slightly hit the apparatus with the head on the ground (this will remove the locking of the fishing line), and the cord due to centrifugal force will move out of the bobbin. Then the fishing line for the trimmer is cut to the required length with a knife, which is located on a protective casing.
  • Manual. To lengthen the cord, it is necessary to stop the device. After that, the fishing line for the trimmer will need to be pulled manually.

Trimmer coil device for grass

Cassyle heads for trimmers come in different designs. both simple and complex. The figure below shows a semi.automatic trimmer head from the Husqvarna motorcycle (Husqvarna).

This type of head is present in the configuration of most benzocosyles and electrimmers such as Stihl (Stihl), Patriot (Patriot), Champion (Champion), Bosch (Bosch), Huter (Huter) and others. The device of the braid head is quite simple. It includes the following details:

  • the base of the mowing head;
  • button for semi.automatic supply of the cord;
  • Spulk (coil), into which a fishing line for a trimmer is refuel;
  • spring;
  • eyes. through them a fishing line for a trimmer goes outside;
  • trimmer head cover;
  • Trimmer fishing line (cord).

There are also simpler trimmer heads shown in the next photo.

All these nozzles do not allow you to change the length of the fishing line in semi.automatic mode (after pressing the button). In the case of a break in the cord, you have to stop the mower and change it manually.

The fishing line for the trimmer does not extend automatically

If, with a light blow, the trimmer coil button for grass on the ground is not lengthened for a trimmer, then the reasons for this may be the following.

Option 1. there was a snack, t.e. Squeezing the cord between turns. This problem usually appears if the user wound a fishing line for a trimmer to the coil unevenly, with the intersection of the turns, or wound it with insufficient tension. In the latter case, when the mowing head is rotated at large revolutions under the influence of centrifugal force, the cord begins to drag on, as a result of which the interitral clamping of the fishing line is possible. To eliminate the problem, you will have to disassemble the coil on the trimmer and rewind the cord correctly, that is, with even turns with good tension.

Stihl Line Trimmer- How to Quickly Exchange the Head in 20 seconds.

Option 2. too short ends protrude from the head. A fishing line for a trimmer may not exit when hitting the ground, if its ends sticking out of the head, insufficient length (short). In this case, the centrifugal force is not enough for the fishing line for the trimmer to stretch. Therefore, it is required to stop the unit (drown out the engine or turn off the ethletric trimmer for grass from the network) and pull the fishing line for the trimmer manually, after pressing the button.

Option 3. a fishing line for a trimmer was soldered inside a mowing head. This leads to the fact that the coil is stopped and does not spin when the button is pressed. Basically, this happens for several reasons: poor quality of the cord, overheating of the coil with prolonged operation of the unit, a fishing line on solid items.

  • In the first case, the cord of third.party manufacturers can be made of low.quality and fusible materials that do not withstand the mechanical and temperature load. Therefore, preference should be given to “branded” fishing.
  • But, if you still purchased a fishing line for a trimmer of unknown quality, and it is often soldered during operation, then you can follow the example of some users who, after refueling the cord, moisten it either with silicone grease (from the spray can) or mineral oil). This procedure greatly reduces the likelihood of soldering a fishing line among themselves.
  • Also, a fishing line for a trimmer can sleep if during a mowing it hit a hard object (stone, fence, dry branch, etc.D.). As a result of this, it is slightly stretched and draws back into the head with high speed. The cord is heated from friction, and its turns are sticking together. The only thing that can be done to eliminate this malfunction is to open a trimmer coil for grass and rewind a fishing line for a trimmer.

Preparation. remove and disassemble the rogue

In most models of electroly and benzotrimmers, to replace the fishing line, you will need to remove the coil. Fubag tool allows you to skip this stage. For the instruction to be universal, we will still consider it in detail: 1.

Fix the shaft. Insert a stop element into the corresponding hole. They may be a thin screwdriver or a metal rod.

Unscrew the spool body. In our example. strictly in the direction clockwise.

Unscrew the lid in accordance with the direction indicated on the case.

The preparatory stage has been passed. You can go to the winding of the fishing line.

Method 1. how to correct the fishing line for a trimmer or put it on a coil and choose the required length

To implement this method, you will need to pre.prepare a fishing line for a trimmer of the required length (usually up to 4 meters). It all depends on the thickness of the equipment used, as well as the design of the coil. There is a simple way to find out the required amount of fishing line, the refueling of which will be needed to charge the coil. To do this, the equipment should be wound inside the coil until it is equal to lateral protrusions. At the same time, the equipment should not go out for these extreme ledges.

The thicker the equipment used, the less its length will need and vice versa, the thinner, the longer the segment will need.

Instructions on how to properly tie the equipment into a tip of a trimmer for grass or motorcycles is the following look:

  • To begin with, a segment of the fishing line, which was prepared to install in a coil, must be folded in half. In this case, one edge should be more than the second by 10-15 cm
  • After that, the second end is taken from the other side, and doubles. Move to it so that the measured ledge 15 cm is preserved
  • There is a slot in the internal partition of the coil, into which the resulting loop should be brought. The slot in the wall is shown in the photo below
  • Next, find out the direction of the winding of the fishing line. If you wrap the equipment in the wrong way, then it will not function correctly, and you will need to redo the work. To insert a fishing line for a trimmer, and wind it in the right direction, you should examine the surface of the coil. It should indicate the direction of winding (in 99% of cases this direction is indicated). What does the direction indicator look like on the coil shown in the photo below
  • This indicator in the form of an arrow can also have a designation, as an example above “Wind Line”, which means the direction of winding. If the arrow indicator is absent on the coil, then you need to look at the head. There is a direction of its rotation on the head, and in order to correctly wind the fishing line for the trimmer, you should wind it on the drum in the opposite direction of the indicator of the arrow pointer. So, if the shooter is on the tip, then you need to wind in the indicated direction, and if it is not there, then you should wind against the direction of the arrow on the surface of the head
  • Having decided on the direction of rotation, you should proceed to the winding. Each end should be carried out in its groove. If there is no separator, then the equipment is necessary in the corresponding distribution order
  • When almost the entire fishing line for the trimmer is wound on the coil, you will need to perform the following-place a short part in the hole of the side wall of the tip, which should be up to 10-15 cm, and then similarly to do the procedure with another end, placing it in the holes from the parallel side
  • We insert the coil into the head, pre.letting the ends of the fishing line into the holes of the drum

We install the drum in place and, pulling the ends of the fishing line, remove them from the engagement with temporary clamps in the coil wall. After that, you can put on the lid until the latch is triggered

With how to put the drum in place, no difficulties arise. There is a second way to charge mowing equipment into a motorcycle. How is it different, and how the second method of refueling the fishing line to the coil of motorcycles is carried out, we will find out in detail.

How to wind a fishing line for a trimmer to a trimmer coil for grass?

Despite the fact that garden equipment has been used for a long time, for some owners of private houses, it is still novelty. That is why questions often arise about how to correctly Win A fishing line for a trimmer for an electric or gasoline trimmer for grass.

cord, dressing, trimmer, head, champion

This is essentially a simple operation, but all its stages need to be performed correctly in order to achieve the desired result. over, in the operating instructions, only a few manufacturers give an answer to this sore question. Study the article and find out how the fishing line for a trimmer is wound on a trimmer coil for grass.

The procedure for winding the fishing line on the coil of a trimmer for grass

First of all, you should know that trimmers for grass have different working nozzles. The coil can be designed for different lengths and thickness of the fishing line. this moment should be taken into account when purchasing consumables.

So, how to charge a fishing line for a trimmer into a trimmer coil for grass? All work is divided into several stages:

  • First you need to disassemble the head of the trimmer for the grass.
  • Unscrew the nozzle, rotating the drum to the right.
  • Press your fingers on two latches located from different sides of the pilots, and remove the top cover of the nozzle. You can put the lid with a screwdriver. This should be done neatly: the drums with automatically feed the fishing line have a spring, which can forcefully discard the lid along with all the contents of the coil.
  • Remove scraps of old fishing line.
  • Now you need to find the middle of the fishing line. To do this, shake it for the required length (for example, 10 m), cut and fold it in half.
  • Hook the middle of the fishing line for the existing recess or insert into the hole, specially intended for this. And start winding. The direction is indicated by the arrow, which is usually applied to the body of the coil of the trimmer for grass (usually against rotation of the drum). Some models have a bilateral coil: in this case, wrap a fishing line for a trimmer in different directions: one end. one direction, the other. to the other, the loop of the fishing line must be brought into the dividing gap located in the middle.
  • Leave the free ends of the fishing line about 20 cm long each. Later they will need to be fixed in the recesses.
  • And finally, the last step will be the assembly of the drum. Install the washers and spring in place. There are two recesses on the upper ring of the coil, where you need to season the antennae of the fishing line. Pass them in the holes and set the coil in the drum, trying to tighten the fishing line for the trimmer and at the same time do not shift the spring.
  • Place the drum cover on top and close it with your fingertips. The latches will become in their place with a characteristic click.

HUSQVARNA WEED EATER TRIMMER HEAD REPLACEMENT

When you turn on the trimmer for the grass, the excess fishing line for the trimmer itself is cut off with a blade of cutting.

As you can see, it is not difficult to wrap a fishing line for a trimmer to a trimmer coil for the grass: the main thing is to do everything right. And here are a few more tips that will be useful to you when choosing a fishing line, its winding and subsequent work:

  • Fishing line for a trimmer can be of different thicknesses and with a different section. The best option for winding is the “native” fishing line for this model for a trimmer;
  • In no case do not use a fishing fishing line for a trimmer or metal cables for a trimmer for grass. Such a replacement may seem effective, but it is very dangerous. Having jumped off the working trimmer for the grass, the cable can seriously injure not only the lawn mower itself, but also others;
  • The fishing line for a trimmer is cut off when a working trimmer for grass is in contact with solid objects. Try not to allow this, otherwise you will have to stop every time, turn off the device and again wind the fishing line for the trimmer to the coil;
  • For cutting lawn grass, use a regular fishing line for a trimmer, and for rough weeds. a fishing line for a trimmer in the shape of a pigtail. It is more durable, and will not constantly cut off.

How to put a chain instead of a fishing line on a trimmer for grass

You can additionally “pump” the unit to mow not only grass, but also weeds and young growth. This does not require expensive tools or special skills. As they say, everything is brilliant just!

  • chain from the old chainsaw;
  • A cup bent inside, which is used to attach a trimmer for grass;
  • washer and nut;
  • vise, marker and ruler;
  • welding machine;
  • drill;
  • Metal for metal.

The length from the ends of the chain to the puck should be the same.

What can be used instead of fishing line

Many users of trimmers are wondering: how to replace the cord, by default used in this kind of devices? Unsafe experiments begin to carry out, installing metal or copper wire, metal cables or strings in a mowing head, as well as a regular fishing fishing line for a trimmer.

If you install a metal cable instead of fishing line, then a trimmer for grass turns into a dangerous device not only for the user, but also for others. This fact is explained by the fact that during the operation of the unit, the steel cable will be gradually shut up, its ends are gradually released, and small pieces of wire will fly in different directions at high speed.

A similar one happens when using steel or copper wire, only with the difference that the torn pieces will be larger and can cause a significant injury.

And if you accidentally hook your or someone’s leg, working as an unit with a steel cable (wire), then a strong and deep section of the fabrics, and in some cases, amputation of the fingers are provided with you. The manufacturer is not in vain for these purposes, nylon uses, since it is quite light and durable, and when separating he does not fly away and cannot cause injury.

It is possible to use a fishing fishing line for a trimmer in a trimmer instead of a standard one, of course, but this will add unnecessary trouble, because it quickly wears out, breaks, mows slowly and does not fit for cutting hard grass. In addition, during the work, a lot of time is lost to replace the broken tool more than once.

In practice, the installation of a regular fishing line is justified if the user is going to mow grass near the fence, especially if he is from a rabid grid. In this case, in order to protect the standard and sometimes expensive cord from wear, it changes to a fishing fishing line for a trimmer, which is not a pity. Usually, in order to change the cord to a fishing line for a trimmer, it must be selected the greatest thickness-2-3 mm.

Replacing the fishing line with a disk or knife

When ennobleing a personal plot, park zones and other places where various plants are required, it is often necessary to change the cutting tool in the trimmer. This is dictated by the fact that the standard cord installed in a mowing head can only cope with herbs. But when a shrub or young growth of trees appears on the path of an employee, a fishing line for a trimmer cannot cope with such a task, and it requires a change to a more effective cutting tool.

Manufacturers of trimmers provided such situations, and complemented their products with a mass of nozzles in the form of knives with several “petals” or in the form of disks similar to circular saws.

If you replace a fishing line for a trimmer with a knife with several “petals”, then such a tool can be mowed by both high grass and plants with thick and dry stems. And changing the fishing line for the trimmer to the disk, the user of motorcycles has the opportunity to cut shrubs or small trees.

Knives and discs are installed according to the following algorithm.

  • The first thing you need to remove, stagnating the shaft, a mowing head (twist clockwise) or a nut with anthers if the unit has not yet been used.
  • Set a saw or cutting knife so that they put on a small ledge (sleeve).

For a better understanding of the process of changing the tool, you can watch this video.

Preliminary preparation

First of all, to wind the fishing line, it is required to remove the coil (bobbin, spool) from the trimmer for the grass. specific actions will depend on the complexity of the configuration and the type of product itself:

  • Small electric trimmers for grass with a working location of the engine and coils in the lower part, as a rule, have side keys on both sides of the bobbin. With the simultaneous press on them, the upper part of the coil, along with the internal contents for winding the fishing line, is disconnected, while the lower remains on the trimmer. It is advisable to analyze the bobbing in an even smooth place, so that the spring does not jump out and not be lost;
  • Electric and gasoline trimmers for grass with a curved rod without the ability to install a knife, as a rule, have coils with a special lamb: in such structures, you should hold the spool in a fixed position with one hand, and rotate the fixing bobbin on the bar with a barack’s baracks. After disconnecting the nut, the whole bobin is removed.
  • Electric and gasoline trimmers for grass with the ability to install a knife on a straight rod (for example, trimmers for STIHL grass) have a hole. For the immobility of the bar, a screwdriver or another suitable object is inserted into this hole and, with slow rotation, such a mutual arrangement is achieved when the screwdriver enters the hole and the bob is fixed. After that, the coil body is scrolled clockwise (with the left thread) and removed from the trimmer for the grass.

For the second and third cases, the coil, depending on the design, are versed in various ways. In the bobbins with a lamb, lamb is twisted, in the reels with latches, latches-fixers are pressed and one part of the coil is freed from the other. If the halves of the spool are connected by thread, then it is enough to turn them with your hands in the opposite directions until they are completely developed.

Types of trimmer heads for coils

The main parts of the trigger is a mowing spike, which is a cylindrical case with a snut.inserted coil (bobbin). A fishing line for a trimmer (cord) is refueling into it. The heads differ from each other in terms of supply and dressing of the cord. There are three types of heads in total:

  • Automatic. The supply of the fishing line is carried out after which, as the user reduces the speed of the motor. Automatic supply of the cord is very comfortable when it is necessary to perform a large amount of work. The minus of such a head consists in a large expenditure of the thread.
  • Automatic. The use of such a head does not ask the user to do some complex manipulations. The principle of its operation is arranged so that the fishing line for a trimmer begins to automatically lengthen at a time when a trimmer for the grass works at full speed. It is only necessary to hit the apparatus with the head of the apparatus a little (this will remove the locking of the fishing line), and the cord will move out of the keyboard due to the centrifugal force. Then the fishing line for the trimmer is cut to the desired length with a knife, which is placed on a protective casing.
  • Manual. To lengthen the cord, you need to suspend the device. After that, the fishing line for the trimmer will need to be pulled manually.

Which line for trimmer is used for a trimmer for grass?

The type of cross section of the cutting thread should correspond to the vegetation that needs to be mowed.

If you need to change the fishing line for the trimmer, then you need to select specifically the type that is recommended by the manufacturer specifically this model of the trimmer for grass, in other words, the thickness of the cutting thread should be suitable for the power of the motor and the size of the unit.

It is better to choose a specialized cutting thread. It is worth soaking a fishing line for a trimmer for some time if you plan to change it in a coil.

After soaking, it acquires an elastic look and becomes stronger.

The cutting thread can be made of various components. Often found in the middle of them. nylon.

cord, dressing, trimmer, head, champion

This material is characterized by the highest degree of wear resistance, the ability to withstand different temperatures and the highest loads.

A fishing line for a nylon trimmer can be stored for a long time, it does not dry out and does not lose its hardness.

cord, dressing, trimmer, head, champion

Therefore, its service life can be quite long.

Coils or heads for motorcycles have a different structure:

How to refuel a fishing line for a trimmer for Champion grass

Warranty production of the factory refueling of a trimmer for the grass will be in demand to change fishing line. Having a very indicative idea of ​​what is really, how to fill the fishing line for a trimmer to the coil of a trimmer for grass without the help of others, the brand new without hunting take up this matter. But with some abilities, the development of this simple science does not represent any difficulties, and the similar annotation presented below will greatly facilitate this common hearing process.

First, for winding the fishing line, it is necessary to remove the coil (bobbin, spool) from the trimmer for the grass. certain acts will depend on the difficulty of configuration and the type of product itself:

  • Small electronic trimmers for grass with a working location of the motor and coils in the bottom, you have side buttons on both sides of the bobbin. With the simultaneous press there, the highest part of the coil, coupled with the internal contents for winding the fishing line, is disconnected, although the lower one remains on the trimmer. The analysis of the bobbin is better to create in an even smooth place, so that the spring entering the design does not jump out of it;
  • Electronic and gasoline trimmers for grass with a curved rod without the ability to install a knife, you have coils with a special lamb: in similar structures, you should hold a spool in a motionless position with one hand, and turn the fixing bobbin on the stalk a barack nut. After disconnecting the nut, the whole bobin is removed.
  • Electronic and gasoline trimmers for grass with the ability to install a knife on a straight rod (for example, trimmers for STIHL grass) have a hole. For the immobility of the bar, the screwdriver is inserted into this hole as it is also called another suitable object and, with unhurried rotation, such mutual placement is achieved when the screwdriver enters the openings, and the bobbin is fixed. After that, the coil body is scrolled clockwise (with the left thread) and removed from the trimmer for the grass.

How to replace a fishing line for a trimmer champion t266

For both cases, a fishing line for a trimmer 2-3 m long is taken. In a single.bona coils, the fishing line for a trimmer extends into the through hole, its ends (antennae) are folded together and aligned, then they are wound in the back of the rotation of the bobbin on the bar the side. the arrow of the arrow is exaggeratedly indicated the correct direction of the winding. In the presence of fixing grooves, the ends of the fishing lines are threaded there in other words, hold the fingers of the free hand, spread into the through hole of the outer half of the bobin, the spool is locked and attached to the bar of the trimmer product.

The difference in the winding of the fishing line in the two-drummer coils is that the line of the fishing line 2-5 m long is in half (to determine the middle fold), and the bend loop is inserted into a special groove between the grooves. Both strains of the fishing line are wound up who on their own groove, fixing antennae and assembly of the coil is similar to the option considered above with one groove.

The 1st implementation of this process, you will seem long and quite labor-cost, but over time and experience, this problem will be solved significantly more frequent and easier.

The video below will clearly show how to tuck a fishing line for a trimmer to the coil of a trimmer for the grass and correctly wrap it. this operation is not any difficulties and, with some patience, will certainly be crowned with a furorur:

There is a type of coils where the automatic mechanism performs winding without the help of others. from the user it is quite true to season the fishing line for the trimmer. The fishing line for the trimmer is passed through the hole on the inside of the case, its antennae without winding are tied through the hole on the outer case, the bobbin is assembled, and when rotating the winding button for the trimmer, the snitches are wound without the help of others. It is unrealistic to make the winding erroneous in such a spool: the mechanism itself will determine the correct direction, since it can only spin in one direction.

Option

In this version, the head is twisted onto the gear shaft. To remove it, you need to fix this shaft. To do this, in such trimmers, for example, in the Huter and Champion devices, a hole is provided through which you can insert either a thin screwdriver or a metal rod.

So, to remove the bobbin, take 2 simple steps.

  • Insert the screwdriver into the hole and stall the shaft.
  • Take the head of the head and start twist it clockwise. It should be twisted in this direction for the reason that the thread cut on the shaft is left.

How to remove the coil and replace the fishing line for the trimmer

The owners of the trimmer for grass, mostly beginners, are confused, the boundaries with panic, when it becomes necessary to change the cutting tool or fishing line for the trimmer in the coil. Too often, when trying to unscrew the lawn mowing head, users simply make it unsuitable for use, not suspecting that it is unscrewed in the opposite direction. To avoid this, if you need to replace the tool, it is recommended to read step.by.step instructions below.

  • Before inserting a fishing line for a trimmer into a coil, turn off the booster engine or turn off the electric trimmer for the grass to avoid injuries that may occur if the cutting tool accidentally begins to rotate.
  • Unscrew the attached nozzle of the transfer shaft. To do this, fix the shaft, combining the openings on the puck and on the axis and inserting a metal rod or screwdriver.
  • Unscrew the nozzle. You should know that the thread on the shaft remains. Therefore, turn the coil of the trimmer for grass to the right, that is, clockwise.
  • Disassemble the mowing head. Most often the main cover is attached on the clips. To remove it, you will need to lower these clamps onto the case, squeezing the edges of the lid. If your trimmer for grass has a semi.automatic mower with a button below, carefully disassemble the nozzle, as you can lose a spring that sometimes pops up when removing the cover.
  • Cut the required amount of fishing. Usually its length is 5 meters. Use the cord with the diameter indicated in the instrument guide. It is not recommended to exceed the maximum diameter of the mowing fishing line, as this will increase the load on the engine and increase the gas mileage.
  • Find the middle of a piece of cord, folding it in half. You will get a loop.
  • Cut the coils of special grooves (there may be holes). Insert the loop of the fishing line into this groove.
  • Wind a fishing line for a trimmer to a coil, turning it counterclockwise. It is necessary to fill the cord as evenly as possible, the turns should be carried out without ceiling and with good tension. After the winding is completed, leave the free ends of the fishing line about 20 cm long and fix them in grooves on the sides of the coil.
  • Collect the mowing head. Before you finally collect the nozzle, do not forget to insert a spring and washer (if available). Insert the coil into the housing and push the ends of the cord through the holes or eye.
  • Put on the lid and fix it with latches.
  • Screw the nozzle back to the gear shaft, also fixing it with a screwdriver. Turn the coil of the trimmer for the grass to the left (counterclockwise).

How to remove the head of a trimmer for grass: Basic rules

It is necessary to remove the trimmer head, adhering to the elementary rules in working with a motorcycle and an electric counterpart, and the main ones we will call:

Jam the gearbox for unscrewing the head with a special hexagon or neatly screwdriver, immersing it in a special hole

The latter can greatly clog with grass and merge with a common color, therefore. delicately clean and find it; It is necessary to jam so that the shaft does not turn; Especially carefully work with the dismantling of a broken or cracked coil. its elements can be everywhere; Many users of a benzo.wrap today are looking for a “trimmer for grass to remove the head” today, and in instructive articles and videos we also make Accent on different types of threads. take into account the nuances of your tool; For ease of work, it is practiced to turn the tool down down the engine, laying on a horizontal surface; Shock and sharp efforts attached when removing the mowing head are inappropriate, since the plastic delicate case can be damaged; Install a new coil or old, if it is still suitable, you need to be a cleaned tool. The new tackle must meet the parameters of the old. Installation of another component, the characteristics of which do not meet the power of braids for grass, can negatively affect its elements and the operation of the mechanism as a whole; We recommend working with a cleaned tool to avoid getting garbage and small particles of grass into the holes; Blocking the gearbox by threading into the groove of the screwdriver is a mandatory procedure when installing a new coil or removing the old; Remember the prevailing of the left thread on the gearbox of most trimmers; Do not forget to remove the screwdriver from the groove groove at the end of the installation of the coil in place; All fixations and removal must be carried out delicately, remembering that the coil is made of thin plastic; It is not worth it to tighten the new coil (or the old one in its place), since after the working hours it will be impossible to remove it at the next time withdrawal

It is also not necessary to fix too easily. weigh the load laid on this node during operation and the resistance of the cutting material; If you need to determine a knife or spool instead of a trimmer for a trimmer for grass. analog cutting tackle, then the gearbox block is also carried out, twisting is carried out according to the same scheme, but the installation itself is slightly different due to the specifics of each individual gear. Mount the knives on a trimmer for grass with a coil if the tool functionally works with different types of gear.

How to remove the coil and replace the fishing line for the trimmer

The owners of the trimmers, mainly beginners, confuse, bordering on panic, when it becomes necessary to change the cutting tool or fishing line for a trimmer in a reel. Very often, when trying to unscrew the mowing head, users simply make it unusable, not suspecting that it is unscrewed in the opposite direction. So that this does not happen, if you need to replace the tool, it is recommended to familiarize yourself with the step.by.step instructions given below.

  • Before refueling the fishing line for the trimmer to the coil, drown out the engine of motorcycles or de.energize the ethletric trimmer for the grass to avoid injuries that may occur in case of accidental rotation of the cutting tool.
  • Unscrew the nozzle mounted on the gearbox shaft. To do this, the shaft must be fixed by combining holes on the puck and on the axis, and inserting a metal rod or screwdriver into them.
  • Unscrew the nozzle. You should know that the thread on the shaft is left. Therefore, to twist the coil of the trimmer for the grass should be right, that is, clockwise.
  • Disassemble the mowing head. Most often, the head cover is attached to the fixers. To remove it, you need to drown these latches into the case, pressing the edges of the lid. If your trimmer has a semi.automatic mowing head, which has a button from below, then disassembling the nozzle should be done carefully, since you can lose a spring that sometimes flies away when removing the cover.
  • Cut the required amount of fishing line. Usually its length is 5 meters. Use the cord of the diameter that is indicated in the instructions for the tool. It is not recommended to exceed the maximum diameter of the fishing line, since this will lead to increased load on the engine and greater consumption of gasoline.
  • Find the middle of the segment of the cord, folding it in half. You will get a loop.
  • Special grooves are cut out inside the coil (there may be holes). Insert the loop from the fishing line into this groove.
  • Wind a fishing line for a trimmer to a coil, turning it counterclockwise. You need to refuel the cord as evenly as possible, the turns should be laid without ceiling and with good tension. When the winding is finished, leave the free ends of the fishing line about 20 cm long and fix them in the grooves located on the sides of the coil.
  • Collect the braid head. Before you finally collect the nozzle, do not forget to insert a spring and washer (if it is available). Install the coil in the case, and prone the ends of the cord through the holes or eye.
  • Dress the lid and fix it with latches.
  • Screw the nozzle back to the gear shaft, also fixing it with a screwdriver. Tighten the coil of the trimmer for the grass will need to go to the left (against h. Arrows).

Is it possible to make a coil for a trimmer for the grass with your own hands

On sale there are a large number of trimmer heads (not automatic), which have a low price and good quality. But sometimes situations arise, for example, in the country, when the trimmer coil broke, and its repair is impossible, the store is far away, and you need to mow. In this case, you can quickly, literally in a few minutes, make a simple trimmer nozzle to fix the fishing line from ordinary plywood 10-12 mm thick.

  • Take a piece of plywood or textolite and draw a circle with a diameter of about 14 cm on it.
  • Cut the disk with a jigsaw or hacksaw for metal.
  • Drill a hole in the center of the disk, suitable in diameter to the gear shaft. Do not forget before installing a disk on the shaft, put a puck on it.
  • You can fasten small corners along the edges of the disk or make 1-2 holes on the opposite sides. They will serve for refueling fishing lines in them.
  • To fix the fishing line for a trimmer, you can screw several screws into the plywood.

Such a homemade mowing nozzle is fixed on the shaft with a nut. Twist or unscrew the nut without fixing the shaft will not work. To replace the cord, it will be enough to release the screws, insert a segment of the fishing line of the required length and press it again.

Also, a mowing nozzle for fixing the fishing line on it can be made from a metal sheet. How to do this can be understood from the next video.

| Denial of responsibility | Contacts |RSS