Do -it -yourself motor boat from a trimmer for grass. Advantages of using a trimmer for grass

Alteration of a trimmer for grass in the boat motor

Motor boats are the most effective tool for moving through water. They are popular among fishermen and tourists, and among other lovers of outdoor water rest. However, the wide distribution of motor boats is prevented by a fairly high cost of engines directly for them. That is why many are interested in the question of replacing mass.produced boat engines with an alternative, cheaper engine. As one of the most popular options, it should be noted the manufacture of a boat motor from a trimmer for grass. How can this be done. in the material further.

In fairness, it should be noted that domestic craftsmen learned to use internal combustion engines from lawn mowers and chainsaws as a boat engine. However, the most simple option in the manufacture of a home.made engine to motor is the use of a gasoline trimmer for grass, which, in addition to a small cost:

  • has a set of all the elements and mechanisms necessary for controlling;
  • has a built.in fuel tank;
  • characterized by the minimum fuel consumption and high reliability in work;
  • It differs in small weight, which allows you to use it on rubber or plastic boats;
  • ensures the tightness of the structure and.

Nevertheless, in order to use a motorcycle as the basis of the motor for the boat, it will need to be modified. This is due to the fact that initially the engine of the trimmer for the grass should function at maximum speeds at a low torque, and for the motor for the boat, another mode of operation is required. However, remaking the trimmer for grass will require certain skills in the performance of locksmithing work. In addition, he will need to develop drawings of some details and have the necessary set of tools at hand.

Refinement of a trimmer for grass by means of a finished set

The choice of a gasoline trimmer for grass as a fundamental device for a boat engine, which is not inferior in its technical characteristics of mass-produced models, such as the “centified ml-5241rd” and others, is due to the presence of a number of nodes that do not need to be finalized. Among them:

  • an economical engine of internal combustion;
  • bar, equipped with a hard shaft;
  • motor launch mechanism (starter);
  • Unbrued fuel tank, so that there is the possibility of visual control of the amount of combustible mixture.

Choosing a trimmer for grass to turn it into an engine into a boat, you should decide on its power. For example, for a small rubber boat “Ufimka-22” a trimmer for grass with a capacity of 0.7-1.0 kW is suitable. A craft equipped with such an unit will be able to develop a speed of about 5-8 km/h. If it is necessary to set in motion a heavier boat, then a trimmer will need for the grass more powerful.

On a note! Choosing the power of motorcycles by weight and dimensions of the existing boat, it is necessary to take into account the mass of the most hinged engine.

You can turn a trimmer for grass into a boat motor in various ways. For example, you can buy a set of finished parts necessary for revision, and use the management attached to it. With it, for a short time (no more than 1 hour), you can turn the motorcycle into the engine to the boat.

The kit for the nozzles for remaking a trimmer for grass in the motor for the boat includes the following details:

  • propeller screw;
  • a special drive, which is made of stainless steel;
  • a set of adapters and nozzles for different types of trimmers (universal);
  • Control handle (room), equipped with a muffler button and a gas adjustment handle;
  • a clamp for attaching a trimmer for grass on the sausage of boats, etc.

, But the engine itself is not part of it.

Important! By mounting the components of the kit per trimmer for the grass, the owner will need to attach the gas control cable to the motor, and then fix the muffler cable, unfolding it towards the rowing screw.

Nozzle for remaking a trimmer for grass in the boat motor. the principle of operation

The idea of ​​a very lightweight hinged motor for small boats, including the simplest ones, is interested in many hunters and fishermen today. It is important to note that the cost of such a motor is quite high and maintenance, however, like details. In this case, many very often began to use the motor trimmers for grass, which are now very popular and common.

What is a nozzle for remaking a trimmer for grass in the boat motor

  • Clamp for installing a homemade boat motor with a trimmer on the boat transmission. This option is more affordable, but at the same time a very effect. Thus, a trimmer for grass is used as a rowing screw. It plays the role of the most ordinary motor, but at the same time it is much less and at the same time requires a little work from the installation.
  • “Propeller screw”. Everything is a little more complicated here, the truth is not a lot. To install this device, you must first look on the Internet. There are a large number of options and at the same time, you need to choose the most suitable ones. for example, the most powerful trimmer for the grass will incorrectly purchase a rubber boat, since otherwise, the boat can simply roll over in front. over, there are a huge number of online stores on the Internet where you can buy trimmers for grass. Their sets include a special drive that is made of stainless steel, as well as a sufficiently large number of adapters to the main (flexible shaft) in the trimmer. Such adapters make it possible to make a universal motor.
  • Another option is the finalization of the lawn mower for the engine for the boat. The best option in terms of price and quality ratio is a standard trimmer for Weedwacker grass, which operates on gasoline. Its total weight is 4.5 kg.

Principle of operation

The trimmer for grass has a higher speed speed of the blades, which makes it possible to move around the water with higher speed, which will begin to proceed with fishing faster than with a motor. Everyone saw how the work of a trimmer for grass. how the lawn and ordinary grass cuts, but here, its blades are turned the other way and at the same time, performs the function of the most economical motor.

And the most important thing is that absolutely everyone can control it. the most important thing is to understand, the higher the blades themselves are to the surface of the water, the faster the speed of turnover and thereby. higher speed.

But if the trimmer for the grass is lower, the speed will be lower. But the most important drawback of the trimmer compared to ordinary boat engines is that they are very loud and you should not use them to the full, if you do not want to frighten off the fish.

Is it worth buying a nozzle to remake a trimmer for grass in the boat motor

It is impossible to give an unambiguous answer to this question, since someone is very accustomed to the motors for boats, while others have never used them. At the same time, if you want a really powerful boat for yourself, then naturally the most profitable and effective solution will be the installation of a standard trimmer for grass. But it should be borne in mind that this option is universal. As mentioned above. the most important thing is to competently combine.

Many experts recommend the blades similar to the blades of your old motor. It is very important that it is necessary to install in strict accordance with the instructions.

It is best to install together with a person who has already carried out such operations and is ready to help at the most difficult moments of transforming a trimmer for grass into a boat motor.

In addition, you should also pay attention to at that time that additional fuel must be taken with yourself, and as well as an ordinary lawn mower, you should give the opportunity to “relax” because due to very long use, a trimmer for grass-motor can simply get out of building right on the water.

The larger the blades, the more effective the trimmer itself will be for the grass.

Alteration Motokosa is as follows:

Initially, there is an alteration of the main bent shaft: first a regular nut is removed from the bobbin with a special fishing line. It seems to be a small tube, the length of which is 20 mm.

At the same time, the nut should be preserved, since the thread on the motorcycles is unusual and it is almost impossible to find the same.

Then the plastic lining with keys is removed. After that, at the very end of the most bent pipe, there is a standard bronze sleeve (often called a sliding bearing). it must be carefully cut out, after that you need to remove the diral shaft, unscrew the nut and metal shaft.

The most important thing is to choose the right blades. Everything here directly depends on what dimensions your boat has.

It is very important to turn its attention to the fact that the best solution will be to enter in the search “Motors to the boat” and on the first site that fall on the site, where the motors are sold and ask a question to the consultant who will offer you his help. you say your own dimensions car, and then, when you get a suitable motor, you need to look at the technical characteristics and find out the dimensions of the blades.

Advantages of trimmers

Many naturally ask why the trimmer for the grass. It has a number of undeniable advantages:

  • light;
  • comfortable;
  • economical;
  • very powerful;
  • It has the main controls: starter, gas handle;
  • It is supplemented specially with a “foot”, which allows you to adjust the power.

How to make a homemade boat motor from a trimmer for grass

Redaying a regular boat, even rubber, is easier in motor: you need to install a gasoline engine on it. Electric is not valued by our fishermen: a heavy, small margin and recharge it during prolonged fishing there is no way. However, the cost of even the simplest option for the boat is fair is 20-30 thousand. R.

#1 EASIEST Way To Edge A Sidewalk (How The Pros Do It)

Trimmer motor for grass: Features

Idea, to use as a boat engine from something else, it occurred to more than one home master. As a result, the engine for the boat with their own hands learned to make from the lawn mower, electric screwdriver, and, of course, the lawn mower. Of course. because the cost of the lawn mower compared to the engine is an order of magnitude less, and the drive power is quite acceptable.

A motor from a trimmer for grass is easiest to make, since the device has all the necessary mechanisms:

  • economical engine. especially when it comes to four.stroke. In most cases, of course, two.stroke is used, since its cost is lower;
  • built.in fuel tank, almost always transparent, so that the fuel level is easily controlled;
  • ready.made controls. starter, gas;
  • a rod with a hard shaft, which transfers torque.

The only difficulty in reinstalling the motor is different tasks for which engines were developed. The gas.cream drive works with large revolutions and a small torque, while the boat should do the opposite. Therefore, in order to build a boat motor from a trimmer for grass, both tools and drawings are needed. In the photo. an example of using a lawn mower as a drive.

Necessary tools and materials

  • Trimmer for grass. for a small rubber boat, a device of 0.7-0.8 kW is enough. According to users, even with such a drive, the boat moves at a speed of 5-7 km/h. For steel, more powerful drives are used. In this case, you also need to take into account the weight of the machine.
  • Duralumin for screw, thickness 2 mm.
  • Clamp or other device in order to fix the engine on the boat.
  • Welding machine. you can do without it only if all the necessary details are purchased.

Manufacturing technology

Trimmers from a trimmer for grass are made in two ways: all parts, like a screw, are bought or produced with their own hands. The second decision will require more effort, but also less costs.

As such, a drawing is needed not for the drive itself, but in the manufacture of a home.made screw. The dimensions of the latter depend on the power of the drive and weight of the boat. A screw with parameters of 10030 mm is quite capable of moving transport weighing up to 120 kg.

  • It is easier and faster to build a motor for a boat from a trimmer for grass, if you choose a model with a straight shaft. If a device with a curved shaft is used. a bent rod, it will have to be redistributed almost completely, since the steel cable in principle cannot transmit a delivery torque. In this case, the tube will need to be made with your own hands from the duralumin, then put a bronze sleeve into it, remaining after disassembling the bent shaft, and insert a re.fitted plastic holder.
  • The homemade screw is cut out of the duralumin plate according to the drawing, the edges are pulled. The blade should have a curved shape, for this they are in turn bend 10 mm. The screw can always be adjusted by cutting or bending more than the blade, if its work during the tests is unsatisfactory.
  • The screw is installed instead of a trimmer head. It is necessary to use a ring nozzle, otherwise the blades can breed the material of the boat or damage it. In the photo. screw fastening.
  • Via the Internet you can find ready.made sets for remaking the lawn mower in the boat. It includes a drive and adapters to the shaft. Adapters are universal, which allows you to do without alterations of a curved bar and shaft. Often such a set includes a clamp. In this case, all work is reduced to the assembly of modification.
  • Control. starter handle, can be used from a trimmer for grass. But if it is uncomfortable, which happens often, it is replaced by any suitable switch. from a bicycle, for example.
  • Homemade boat motors from a trimmer for grass are fixed with clamp on the boat mince.

Necessary tools and materials

Manufacturing technology

Trimmers from a trimmer for grass are made in two ways: all parts, like a screw, are bought or produced with their own hands. The second decision will require more effort, but also less costs.

As such, a drawing is needed not for the drive itself, but in the manufacture of a home.made screw. The dimensions of the latter depend on the power of the drive and weight of the boat. A screw with parameters of 10030 mm is quite capable of moving transport weighing up to 120 kg.

  • It is easier and faster to build a motor for a boat from a trimmer for grass, if you choose a model with a straight shaft. If a device with a curved shaft is used. a bent rod, it will have to be redistributed almost completely, since the steel cable in principle cannot transmit a delivery torque. In this case, the tube will need to be made with your own hands from the duralumin, then put a bronze sleeve into it, remaining after disassembling the bent shaft, and insert a re.fitted plastic holder.
  • The homemade screw is cut out of the duralumin plate according to the drawing, the edges are pulled. The blade should have a curved shape, for this they are in turn bend 10 mm. The screw can always be adjusted by cutting or bending more than the blade, if its work during the tests is unsatisfactory.
  • The screw is installed instead of a trimmer head. It is necessary to use a ring nozzle, otherwise the blades can breed the material of the boat or damage it. In the photo. screw fastening.
  • Via the Internet you can find ready.made sets for remaking the lawn mower in the boat. It includes a drive and adapters to the shaft. Adapters are universal, which allows you to do without alterations of a curved bar and shaft. Often such a set includes a clamp. In this case, all work is reduced to the assembly of modification.
  • Control. starter handle, can be used from a trimmer for grass. But if it is uncomfortable, which happens often, it is replaced by any suitable switch. from a bicycle, for example.
  • Homemade boat motors from a trimmer for grass are fixed with clamp on the boat mince.

In the video, the process of converting the lawn mower into a boat drive is discussed in more detail.

Popular articles

The advantages and features of the alteration of the trimmer for grass in the boat motor

The use of the lawn mowing available on the farm has a number of advantages. Firstly, the owner of the boat will not overpay for an expensive motor purchased in the store. Secondly, the motor for a boat from motorcycles consumes much less fuel than specialized boat engines. Thirdly, the engine from the lawn mower has an order of magnitude smaller dimensions than the boat engine purchased in the store. There are a number of other factors forcing fishermen to use a trimmer for grass instead of a boat motor.

  • high reliability of engines of modern trimmers;
  • complete tightness inside the body;
  • the presence of all the elements necessary for the control of a home.made engine;
  • The presence of a built.in tank.

Thanks to all these factors, the boat motor from motorcycles is most popular among enthusiasts.

In the process of processing the engine from the lawn mower to the boat engine, it is extremely important to consider that this power unit was produced for other purposes. Trimmer engines operate at small torque, but, at fairly large speeds. In the case of a specialized boat engine, everything happens the other way around. In this regard, to remake a motor from a trimmer for grass, you will need to prepare drawings, equipment and observe a certain procedure.

Despite some difficulties in converting, it is in the trimmer that all the details necessary for the manufacture of the boat engine are a built.in starter and a gas lever, a rod with a hard shaft and a translucent fuel tank.

Ready set of nozzles

At the moment, there are ready.made nozzles for a lawn mower, allowing you to convert your mower into a boat motor with minimal efforts.

The prefix already has a ready.made solution for attaching it to the gasoline engine of a trimmer for grass.

Also, the control handle with the muffler button is attached to the bar. The gas handle is made according to the likeness of the bicycle (meaning a bicycle with speed switching) and has a rattle that fixes the selected position.

This set even includes a special clamp, designed to fix the entire structure on the boat (on the vessel).

The nozzle for a trimmer for the grass is collected without difficulty, since its design is very simple. Only remains:

If you read the reviews on the Internet about this device, then they are mainly positive.

.

Ready set of nozzles

At the moment, there are ready.made nozzles for a lawn mower, allowing you to convert your mower into a boat motor with minimal efforts.

The prefix already has a ready.made solution for attaching it to the gasoline engine of a trimmer for grass.

Also, the control handle with the muffler button is attached to the bar. The gas handle is made according to the likeness of the bicycle (meaning a bicycle with speed switching) and has a rattle that fixes the selected position.

This set even includes a special clamp, designed to fix the entire structure on the boat (on the vessel).

The nozzle for a trimmer for the grass is collected without difficulty, since its design is very simple. Only remains:

If you read the reviews on the Internet about this device, then they are mainly positive.

.

Do.it.yourself motor motor

The easiest way is to make a motor for a boat from a trimmer for grass with a straight bar and a hard shaft. If your unit has a curved bar, then it will have to be redone.

Alteration of the curved shaft

First of all, it is necessary to get a full.time nut under the number 2 shown in the diagram below. It looks like a cylinder 2 cm high with a thread chopped inside it.

Important! All unscrewed nuts must be saved, since non.standard threads are cut into them (not metric and not inch).

Further, the alteration of the rod is as follows.

  • Remove the metal flexible shaft (9) and Deadwell Val (8) from the bar, promoting the nut (4).
  • Since the end of the bent bar does not contain any bearings, and their role is played by a bronze sleeve (6), it is required to cut it out.
  • After the bronze sleeve (6) will be extracted, you need to knock out the plastic tread (10). Since the pipe is metal and curved, it will not be possible to align it, you can safely throw it away.
  • Pick up a duralumin, with a similar diameter (internal) instead of an emitted pipe. It will be better if the diameter is slightly smaller than the diameter of the previously extracted sleeve.
  • It is necessary to press the bushing (6) from bronze into the pipe. You may need to squeeze the pipe a little.
  • Express the groove bushing (5) using a hammer. You need to do this very carefully, without making a lot of effort, so as not to deform the sleeve (6).
  • Tread (10) is cut to the desired diameter and tightly inserted into the bar.
  • In the case when the tube you have chosen will have a large external diameter, and you cannot insert it into the hole of the motor head, you will have to pave it to the desired size.
  • Instead of a flexible shaft, you can take a steel rod and connect it to the edwal shaft (you will need the help of a turner).
  • The screw is fixed to the shaft using a nut (2).
  • The bar with an internal shaft is attached to the motor with adapters made specifically in a lathe. There is no universal drawing of adapters, since different models of trimmers can have their own design features.

Using a gearbox from an angular grinder

Also, for the independent manufacture of a boat engine, based on a trimmer for grass, a gearbox is often used from corner grinder, but with some improvements.

  • It is necessary to disassemble the gearbox, and instead of a shaft with a gear, order a new, longer one (respectively, a trimmer for grass). The end of the shaft is made similarly to the extracted (short) so that you can use the same bearings and gear.
  • It is advisable in the place where the bearing is installed, install the oil seal so that the water does not fall into the gearbox.
  • The gearbox body is twisted using sealing gum and sealant.
  • You can fill the lubricant inside the gearbox, or cover the gears abundantly with thick grease.

Production of a screw

To make a screw for the boat engine, you can use a small piece of duralumin 2 mm thick. For the screw, you will need a strip of 30 mm wide and 100 mm long. Make it according to the drawing below.

By step step, the following is meant: if you place the propeller on the table, then from its surface to the blade there should be a distance equal to 10 mm. The angle of inclination of the blades is easy to adjust with the help of pliers, after preliminary annealing duralumin.

This option is not final, and on the Internet you can find a lot of screw drawings with two blades, with three blades, as well as different dimensions. In each case, the size of the propeller is selected individually.

Boat motor

How nice in warm summer weather to ride in a boat. One bad thing. I don’t want to pick up the oars. Smoking comes to the rescue.

And what if you adapt to the boat a motor from an electric screwdriver using improvised tools for this?

What is easier to apply the following materials for this “idea”:

The essence of the idea is the following. In a rabbit (in this situation. a rowing screw), an equal to metal stiletto is drilled in diameter. The screw is installed on the hairpin and securely fixed. The long hairpin itself is inserted into an electric screwdriver that turns the hairpin with the screw. The engine for the boat is ready!

It remains only to come up with some kind of metal structure that will reliably fix the electric screwdriver on the boat itself. But this is too simple a task to discuss it. And every amateur will be able to show his inventive abilities in this matter.

We lower the screw on the hairpin into the water and turn on the electric screwdriver. It remains only in a hurry to swim and enjoy those beauties of nature that you see around. There is only one but. really evaluate the capabilities of the batteries and “do not swim for buoys”.

Principle of operation

The trimmer for grass has a higher speed speed of the blades, which makes it possible to move around the water with higher speed, which will begin to proceed with fishing faster than with a motor. Everyone saw how the work of a trimmer for grass. how the lawn and ordinary grass cuts, but here, its blades are turned the other way and at the same time, performs the function of the most economical motor.

And the most important thing is that absolutely everyone can control it. the most important thing is to understand, the higher the blades themselves are to the surface of the water, the faster the speed of turnover and thereby. higher speed.

But if the trimmer for the grass is lower, the speed will be lower. But the most important drawback of the trimmer compared to ordinary boat engines is that they are very loud and you should not use them to the full, if you do not want to frighten off the fish.

What can be done from a trimmer for grass?

The amount of equipment that can be made on the basis of a gasoline braid for grass is a fairly large. The endurance and supply of torque of the motor motorcycles makes it possible to collect homemade dampers that will be highlighted by high speed and stability when working in any operational conditions.

The engine from motorcycles can become a suitable basis for the manufacture of a motor that can drive a small rubber boat in motion. The maximum speed of the water vehicle will be approximately 15–20 km/h. At the same time, two adults can be on board the boats and their luggage.

To make an boat engine boat from a trimmer for grass, a gearbox and a metal rowing screw will definitely be required. The gearbox will take rotational effort from the motor, and transfer it to the screw. The latter, during its rotation, will create a force that can push the boat. It is very important that the screw is made of stainless steel. Otherwise, due to constant contact with water, the node will eventually begin to succumb to corrosion.

When remaking motorcycles to the boat motor, you need to leave the standard fuel tank motorcycles. For refueling the boat engine, the fuel mixture prepared in the same proportion should be used as for the operation of a garden tool.

Snowman from a trimmer for grass

Do.it.yourself home.made homemaries with your own hands often include a snowman. This type of household equipment will make it possible to clear small areas from freshly conquered snow. If the power of the used trimmer for grass exceeds 3 liters. With., then a home.made snowman can also be used to clear the territory from ice and snowdrifts, up to 1 m high.

To assemble homemade, you will need a fencing bucket that can be boiled from metal plates. A simpler option is the manufacture of a bucket from an old gas cylinder. For crushing the snow, a screw placed inside the bucket will be responsible.

From the bucket snow and chopped ice will fall into the gutter, for the manufacture of which a round pipe with a diameter of at least 20 cm is required. Snow masses will be thrown out of the gutter to the side, which the operator selects by turning the lever.

An important plus of a home.made snowman lies in a large range of snow discarding. Depending on the engine power, this parameter can be from 2 to 12 m.

Snowman from a trimmer for grass: nozzle for cleaning snow, homemade for the lawn mower two in one, which can be made with your own hands from a corner grinder

Every winter, after the fall of the first snow, you begin to think about buying a snowman. The mechanism that throws back the snowball for you is the dream of many. for such equipment of ordinary people can drive into a stupor. It’s easier to make it yourself from the existing tool. Let the snow remove and do something else. In the article we’ll talk about how to make a snowmaker from a trimmer for grass with your own hands.

“Snowman” from a trimmer for grass and motorcycles. the principle of its work

Options for the manufacture of a snow.offer from motorcycles are many. Let’s dwell on the simplest way. Replace the cutting knife with a rotor. This snowman will work as an ordinary shovel. Just do not have to raise it, you just need to carry it on the ground. She will rake snow and throw it away.

Materials and tools

We are the task: a snow removal car with your own hands from a trimmer for grass. One condition: a braid for grass should be with a straight bar and a gearbox at the end. It is desirable to have a multi.toothing disk in a set for mowing thick grass. Next, we buy beer, Baltic in a large tin barrel.

We drink. We get the main of the materials. metal. A drill, corner grinding, welding machine will come in handy from the tools.

Non.mere people can replace the bottom of the barrel with sheet metal, 1.5 mm. Using the welding to make the necessary parts.

Step.by.step manufacturing of parts and assembly

We start creating spare parts. Cut the barrel in a circle, at an altitude of 150 mm from the bottom. From below we make a hole in which the protruding part of the gearbox is a trimmer for grass. We drill 3 more small holes. They must be located in such a way that coincide with the holes for fastening the shield on the gearbox.

On the side we make a square slot, with dimensions 100 per 100 mm, for snow release.

The upper open part of the workpiece is closed, by a third, a piece of tin. Previously making sure that the emission gap is located in the center of the closed part.

We make a rotor. Cut 4 blanks of rectangular shape, 250 per 100 mm. We betray each blank, cutting one of the corners on the long side. We weld them to the trimmer disk for the grass with a cross. The rotor is ready.

The deflector responsible for the direction of snow emission is also made from the remains of the barrel. Cut the metal strip 150 mm wide and 300 mm long. Lightly bend the workpiece. We weld the sidewalls to it, 100 mm high, preventing the scattering of snow at the output.

The last thing to do is the scapula. We take a piece of metal with sizes 300 by 400 mm. Bend the edges. We get sides 20 mm high.

  • We take the case and weld to it the deflector, in the place where the slot for release.
  • We fix the shoulder blade from below.
  • We insert a trimmer gearbox for grass into the hole and fasten the bolts.
  • Install the rotor like an ordinary motokos knife.

If this instructions are not enough for you, then you can always read this article in which the process of assembling a shovel for a snowman with your own hands is considered in more detail.

yourself, motor, boat, trimmer, grass, advantages

Use this device on full gas. Frequent pressure on the gas trigger will lead to engine breakdown or clutch. Some of the readers may have already thought about the acquisition of a high.quality and reliable apparatus, which will be able to last for many years and if you are one of these people, then follow the link and learn about the self.propelled gasoline snowman Patriot.

complete information on the above

Grinding machine. snowmaker from corner grinder

A snowbox from a corner grinder is made on the basis of wooden sleds, to which the rest of the mechanism is attached. The design contains: deflector, rotor and its casing. A sheet of steel in the shape of a shovel is attached in front. Corner grinder plays the role of the drive, and is responsible for rotation of the blades.

How this miracle of technology works? The operator pushes the sled, rally the snow in front of him. Snowball, falling on a shovel, enters the rotor’s blades and is thrown to the side.

The principle of operation of this device is very similar to a mechanical snowman, which we will talk about here.

What and what to do from

The assembly will require plywood, a thickness of 20 mm, from which a sleigh and a handle will be made. Sheet metal, 1–1.5 mm, is useful for the manufacture of the main parts of the apparatus and raking shovels. Metal tube of small thickness. Semiautomatic type welding machine. Drill, jigsaw and some manual tools.

Let’s start with the manufacture of the base. Drink two blanks in size 610 per 100 mm with a jigsaw, cut one of the edges under 45 degrees. Two pieces of plywood will be required, with a size of 370 by 50 mm, to connect them.

Another detail, 370 to 100, in which a semicircle is cut out in size. Runners are ready, proceed to the creation of a pen

From the same sheet of plywood we make two bars with a width of 50 mm and a long operator growth.

Keep in mind that the handle will be at an angle relative to the runners. Its length can be measured experimentally.

Two more bars. struts similar to the width will provide a durable fastening of the handle. Their length depends on the angle of inclination of the handle.

STIGA electric lawn mowers will give your site a well.groomed view in a matter of minutes.

This article contains useful tips on which chainsaw to choose.

Before purchasing the Buler tractor, you should carefully familiarize yourself with its technical characteristics that are here // MachinSpec.COM/SELSKOXOZYAJSTVENNAYA/TRAKTOR/BUHLER.HTML.

We make a scraper. Iron sheet 570 mm long and 150 mm wide. We bend it in such a way that it turns out a shovel, with a base size of 370 mm, an initial side height of 100 mm and the opposite side of 570 mm.

Let’s proceed to the manufacture of the main details. Cut the strip 330 mm long from metal and 250 mm wide. We turn the resulting workpiece into the ring. We fix it with spot welding. We make the bottom for the learned pipe and weld it in place.

Now you need to make 2 holes. One will be in the center of the bottom. Its diameter should be equal to the protruding part of the gearbox cover of the corner grinder. The other hole is located on the side. Its dimensions are 150 by 200 mm.

We make a deflector who is responsible for the direction of the release. It consists of a rectangular plate of 420 by 150 mm and two side supports of a triangular shape. Long side of the triangle 420 mm height 150 mm. At its base you will have to cut a semicircle for a tight fit to the body.

Humadies from a trimmer for grass: homemade trimmers for grass: DIY snowmaker, drawings, ice drift, motor, engine bicycle, cultivator, snowmobile

For everyday household work, outdoor activities or travel, using a motor from a trimmer for grass, many craftsmen can independently make different devices:

Humes are much cheaper than factory analogues, but at the same time are not inferior in power and efficiency. Using the necessary set of tools and a minimum of knowledge, you can achieve great results in the manufacture of motorcycle equipment with your own hands. Such units are characterized by simplicity of design and minimal financial costs.

yourself, motor, boat, trimmer, grass, advantages

A bicycle with an engine from a trimmer for grass

Homemade bicycle with a motor from a trimmer for grass is a high.tech vehicle that differs from simple analogues of high driving speed, practicality and low cost, using cheap configuration.

The following devices are needed for the assembly of a motorcycle:

  • bicycle in working condition;
  • a motor from a trimmer for grass;
  • chain;
  • tensioner;
  • star;
  • clamp;
  • cable;
  • fuse;
  • controller;
  • exhaust pipe;
  • sleeve, bolts, washers.
  • 2 rubber gaskets are attached to the rear wheel: the first between the knitting needles, the second is behind them.
  • Asterisk should approach a trimmer motor for grass. It is inserted into the sleeve, which is located on the outer part of the wheel. The crescent is attached to the inside.
  • The engine is mounted on the trunk or behind the seat using a clamp bought or made of a steel plate with your own hands.
  • Install the chain on the asterisk and the power unit, regulate the tensioner. Instead of a chain, it is not recommended to use belts. Under the influence of friction force, they often become unusable, their service life is minimal.
  • Gas handle and engine are connected by cable.
  • Fasten the tank for fuel and carburetor.
  • The exhaust pipe is welded by a weld seam.

See »How to make a snowman from a trimmer for grass

Some craftsmen create a braking system and replace standard wheel tires with non.slip. After the assembly of all nodes, they must check the bicycle work. The functionality of the mechanism and its own safety will depend on this.

yourself, motor, boat, trimmer, grass, advantages

Ice Bour

Ledobur from a trimmer for grass is a low.power unit for lovers of winter fishing, characterized by a little weight and convenient transportation. In order to save money on the purchase of new equipment and forces necessary for manual drilling of ice, fishermen make them from old trimmers. This is needed:

At home it is difficult to make ice drift. Details to which you need to pay attention are screws and the base for knives.

  • Calculate the sizes of product segments.
  • Prepare metal blanks, mark, cut the sector, cook segments among themselves. As a result, a steel spring is made on one side.
  • Stretch the spring on a given step on a special machine in order to boil the segments from the other side.
  • Grab the rebid and weld it to the pipe.
  • Boil the joints of the screws and paint.
  • When choosing rotation of the screw, the direction of rotation of the benzo tool is taken into account.

Converting a trimmer for grass in a benzobur is suitable for units with a folding bar. The adapter for the connection is the easiest to prepare.

If it is necessary to increase the rigidity and stability of the mechanism, make a strong frame for attaching the gearbox and motor.

Motoburs. units for laying holes for installing wooden piles, laying the foundation, drilling wells. The principle of operation and the method of manufacture is similar.

Snowmobile or snowfall

Based on the trimmer motor for the grass, you can convert to a self.propelled vehicle for movement along a snowy flat terrain or a simple snowbreaker (motorized sleigh) for steep descent from the mountain.

Self.propelled guns. a frame structure, including:

The frame is made of welded spars, on which racks of 30×30 cm are welded and cross. A steel pipe with a diameter of 14 mm is taken as a drive shaft. Skiing-musculoskel. Moving the snowmobile occurs with a screw or chain transmission.

Homemade RC boats with weed eater engines, NASBOAT!!

What else can be done from a trimmer for grass

Homemade motorized motor vehicle. a vehicle for moving at short distances along the sidewalks and park tracks. The mechanism develops speed up to 40 km/h, due to wheels of small size it has small stability, for large loads and cargo transportation is not intended.

An old scooter is suitable for assembling the product, which mechanize:

  • install stiffeners using a square metal profile to enhance the frame;
  • selected stable and wide wheels, for example from a garden trolley;
  • The gearbox is made to transmit power from the engine to the rear wheel with chain gear;
  • Install brakes, gas handles and cables.

Motorized scooter is a good technique, but it must be remembered that children should not give such a “toy”.

| Denial of responsibility | Contacts |RSS