Grass trimmer gives gas and stops the reason

How to fix a string trimmer that won’t prime (purge bulb doesn’t work / won’t fill)

What to do if the fuel mixture used is fine, but still does not start the grass trimmer gasoline? The cause of the mechanism failure may be excessive moisture in the spark plug passage. To make a diagnosis and fix the problem, you need to do the following:

  • Unscrew the spark plug. Wipe it thoroughly and then dry it.
  • Drain the excess fuel in the chamber through the appropriate spark plug hole.
  • Clean the old candle, if there is soot on its surface. To cope with the task will allow the use of an ordinary nail file or nail file.
  • When installing the element in place, set the gap of 1 mm. To check the parameter, it is enough to place any coin in the gap.
  • Reassemble the functional unit.
  • Try to start the grass trimmer.

It is advisable to dry the spark plug passage for at least half an hour. But you should by no means resort to burning its elements. After all, the heating of the spark plug can lead to its final deterioration. What to do if the service of the functional unit was performed in accordance with the above recommendations, but the grass trimmer does not start, the spark is? In that case it is worth to treat the threaded joints with gasoline. The latter does not need to be abundantly impregnated with fuel. It should be only slightly moistened. You should resort to such actions to ensure the ignition. After all, no matter how strong the spark did not give the plug, in a completely dry chamber will simply be nothing to ignite.

lawn mower stops or suffocates when you press the gas

If even in this case the grass trimmer does not start, it is worth to evaluate the quality of contact between the high-voltage wire and the spark plug. If there is no spark (if there is a reliable connection between the specified elements), most likely the problem is caused by a failure of the ignition unit. In this situation, you will have to turn to the services of craftsmen, who will perform the resetting of the unit.

See also  the grass trimmer does not pick up speed

At high rpm

When the grasshopper stalls at high speeds, it is due to the following malfunctions:

  • The first thing to take care of is the work area where the cut will be made;
  • The carburetor has become misaligned due to vibrations from the mechanism;
  • problems with fuel mixture circulation;
  • Atmospheric air suction;
  • the hose intended for fuel intake is cracked or loose.

Adjust the carburettor based on the instruction manual for your trimmer. To adjust the carburettor, it is often sufficient to loosen its housing. If there are problems with the circulation of the fuel mixture, it can slowly flow into the carburetor. The engine will choke at high engine speeds after the choke has worn out.

What could be broken

Problems with the chain saw, related to the fact that this device does not start, are classified in a specific way by service technicians. They are highlighted by malfunctions with the following nodes of the mechanism:

  • engine, in which a piston and bearings can wear out or fail, crack the crankcase;
  • fuel supply system, with all this there may be a clogged filter or difficulties with the carburetor;
  • mechanical damage to wires, pipes, hoses;
  • the ignition circuit.

Chainsaw stalls when throttle, idling or under load: causes and solutions

The work of the two-stroke engine is based on the interaction with the carburetor and the ignition system, providing fuel, air and spark to the combustion chamber. Malfunctions in these components, as well as the motor piston group itself, can lead to serious malfunctions in the tool. Unscheduled shutdown of a running engine is a frequent occurrence due to defects in key components of the system. Fortunately, in 90% of cases, you can identify the source of the problem and restore performance on your own, with basic skills and minimal monetary or time costs.

At high rpm

When the grasshopper stalls at high rpm, it is due to the following malfunctions:

  • a clogged or stuck valve located on the tank lid;
  • the carburetor has become misaligned due to the vibrations produced by the machine;
  • fuel mixture circulation problems;
  • Atmospheric air inflow;
  • the hose intended for fuel intake is cracked or poorly connected.
See also  How to put on the grass trimmer belt correctly

Top Reasons String Trimmer Starting, Then Stalling — String Trimmer Troubleshooting

Adjust the carburetor, referring to the instruction manual of the trimmer. it is often sufficient to loosen the tightening of the carburetor housing. If there are problems with the fuel mixture circulation, the mixture may slowly flow into the carburettor. Engine stalls at high RPM after running out of fuel.

grass, trimmer, stops, reason

Why does the chain saw start and quit right away?

The chain saw starts and stops right away, the reason for this behavior may lie in the carburetor. A fuel pump malfunction or a problem with the main fuel nozzle may be the cause. The inability to operate the chainsaw after starting, requires a complete diagnosis in a service center.

Read also: Linear guides for NC machine tools

All of the above options for improper engine operation have similar causes, which, depending on their neglect, can have different manifestations. For example, if there is a small amount of air leakage into the crankcase, the operation of the engine will not change much, the engine power will drop slightly, its maximum speed will increase, and it will be able to heat up a little more. Moderate levels of air intake will cause the engine to idle and become hot while running. Severe air intake, will make it impossible for the saw to operate, it will start and immediately shut down.

Parallel to the visible manifestations of malfunctions, for example, the inoperability of the chainsaw after start-up, there will be processes inside the engine at the moment of its malfunction, which irreversibly lead the saw to the most severe consequences, for example, melting of the piston, jamming of the crankshaft.

The air filter is dirty

To check if the air filter is dirty is rather easy. You just need to take it off and start the chain saw without it. If the chain saw is running fine, it is the problem and it just needs to be changed or washed, depending on its type. And don’t be afraid that the chainsaw will run for a while without dust protection if you don’t have a dust cloud around it, then it’s okay.

grass, trimmer, stops, reason

So, removing the air filter. To do this, you have to remove the cover from the back top of the chainsaw, which is attached either with screws or just some locking device that you just have to turn or snap off.

If after the filter is removed the saw works fine after starting it up, it means that it is dirty.

The air filter is either a felt or nylon filter. The first resembles absorbent cotton or sintepon, and the second looks like a fine mesh of nylon threads stretched on a plastic casing. The felt one needs to be replaced with a new one, but the nylon one can simply be washed in soapy water, dried and put back in place.

See also  Hay trimmer for power tiller with his own hands

Nylon filter

felt filter

And then quietly use the chainsaw.

Lawn mower stalls on throttle: Causes and solutions

Lawn mower and gasoline grass trimmer. machines that do not just mow the grass, and mow it up to several times more than their counterparts that have an electric motor. Once the lawnmower or gasoline trimmer stops for a while and the cutting process immediately comes to a standstill.

Right off the bat

Your mower may malfunction immediately after starting if the carburetor is misaligned or not properly adjusted. It causes an uneven fuel supply. As a result, the device clearly vibrates. To correct defects carburetor readjust, following the annotation to the mechanism.

In addition, the engine stops when the fuel valve is clogged. In such cases it is quite easy to clean it. If the hedge trimmer works at first and then shuts down immediately, the fuel might be having some difficulty getting to the carburettor. The problem can be solved by loosening the valve, which ensures the free circulation of consistency in the system.

Weedeater starts but dies. Easy quick fix.

Also stopping can be caused by air leaks in the presence of mechanical damage to the hose (holes, cracks), receiving fuel. In this case, increase the speed of the drive to remove air bubbles from the system faster.

| Denial of responsibility | Contacts |RSS