How to cut a sink hole in a countertop

How to cut the sink into the countertop simply and easily. step by step recommendations with video

From our article you will learn how to properly cut a hole for the sink in the countertop, what you need to consider and what is better to cut a countertop under the sink.

sink, hole, countertop

“To save money, that’s the way to go,” reasoned the thoughtful homeowner. And not only order a budget kitchen, but also plan to cut a hole in the countertop for the sink themselves. True, this operation only seems simple at first glance. To achieve a successful result, you need to:

  • know how to work with this or that material (for example, a quartz countertop will not cause difficulties);
  • Have a set of necessary tools (or know where you can rent one);
  • Understand the nuances so as not to spoil the product (expert advice is important here).

Only then you can achieve maximum quality and after completing all the work to enjoy flawless operation of the kitchen for many years.

Performing the installation of the sink

During the installation of the sink the following actions are required:

  • First it is necessary to cut a hole for the sink.
  • After that, you should position the product in the cut-out opening and make sure that it is stable.
  • Next you need to perform the installation of plastic spigot with the use of a carved gasket.
  • It is necessary to connect all the components, and then check their tightness and tightness.

Please note! In order to avoid cracks and deformations it is necessary to avoid twisting of these elements.

  • Then you need to install the spigot into the siphon and tighten the nut with the sealing ring.
  • Screw the flexible hoses for cold and hot water to the appropriate holes.
  • Then the screw and washers for the mixer body must be inserted.
  • The next step is to proceed in a similar manner with the flexible hoses.
  • Next, with the use of dowels and self-tapping screws, it is necessary to perform installation of brackets.
  • Once you have finished, fit the sink into the countertop hole.

After carrying out these actions it is necessary to make sure that the sink is firmly placed on the brackets, and then you need to make their strengthening up to the stop. Then you can connect the plumbing fittings.

The last step is to seal the joints. If during the application of the composition there is a surplus, it should be removed with a soft rag before curing. Otherwise, it will take more time and effort to remove the silicone or sealant of another variety after curing.

The above described sequence of actions when installing traditional sinks, but it must be remembered that the installation should be carried out taking into account the design features of the sink. For this reason it is also necessary to get acquainted with the nuances of fixing other types of products.

The installation of the sink

When installing it, you should ensure that the placement of the supply and drainage tube was comfortable with the absence of kinks, due to which, over time, elements will crack. This defect may arise due to the small installation space.

The shape of the basin must be outlined. Then you must mark the inner contour to fix the sink. For the convenience of cutting the opening for the sink first thing is required to make a hole, which then must implement the installation of the cutting element of an electric jigsaw.

Important! In order to obtain a durable and long-lasting seal, you must use the gasket that comes as standard with the sink. Additional joint should be made by means of sealant.

Fixing the integrated sink

You must install this type of product butt to butt, observing the gaps, which do not exceed 1-2 mm. They should be grouted with a special compound, sealed and sanded, which makes it possible to achieve a homogeneous appearance.

Extreme care must be taken with the installation of the integrated sink, because otherwise it could easily be damaged. The greatest attention should be paid to the accuracy of marking, which determines the maximum compatibility of the sink with the countertop

Mounting a corner sink

The installation technology of this type of shell does not differ from the above method. The only difference is that the cabinet must be rotated at right angles. The sink must be rotated 45° for comfortable use. In this case, the location of the sink will be right in the center.

When marking, the upper corner of the product should be held towards you, and the wide one near the wall. A correct marking helps to avoid warps and very large gaps between the wash basin and the worktop.

See also  Bosch toaster does not lock the start knob

Fixing stone sinks

These sinks have a considerable weight, which must be taken into account, because for this reason there are a number of certain restrictions on the installation. Sturdy steel brackets are required for the installation of the stone sinks. It is advisable to provide additional supports to increase safety.

Because of the sink’s large mass, it is advisable to install it together with someone else. The product itself in the installation process should be unhurriedly and smoothly immerse in the hole on both sides. As a result, the sink must be placed on the brackets and firmly fasten, and then you need to make the connection of the sanitary equipment.

Protect from moisture

Having previously checked the cutout for unobstructed sink entry and degreased with acetone. Silicone application. Protecting your finger with a glove, carefully rub the silicone into the end face, without sparing it at the same time.Along the edge of the saw cut, make a silicone ring to prevent the penetration of moisture.

Within walking distance of you, placed a service for the calculation of cabinet furniture.

Preparatory work

Before you mortise the sink in the kitchen countertop, you must make sure that the current water supply to the area in which you plan to install the product is reliable, as well as how well established sewage system. One of the tools required for this work is an electric jigsaw. If not, you will need to borrow it from your friends or rent it. If the jigsaw is only needed for the described task, it makes no sense to buy it, but you should not start working without it either. In addition, in the course of installation it is necessary to have a sealant. It is best to give preference to transparent compositions based on silicone.

Together with the sink you may also get a ready-made template for cutting it out, which is its packaging. Otherwise, in the future it will be necessary to carry out its drawing on the countertop, performing the application of the product itself to its surface. If the kitchen set has just been purchased, it is likely that it does not have openings and for the pipes, which, together with the trap and all the necessary hoses for their connection will also have to buy. Together with the sink they are generally not supplied in the package.

sink, hole, countertop

Please note! If the kitchen furniture is still only to assemble, then you do not need to hurry to carry out fixing countertops, as before it is fixed in it is much more comfortable to cut a hole under the sink.

Secrets of installing a square sink

Installation involves the same algorithm that works with sinks of other configuration. The main thing is to draw all the lines correctly: first mark those that run parallel to the edge of the countertop (with an indentation of the width of the sink), and then take the perpendicular ones.

It is noteworthy that the siphon is placed at the intersection of all these lines.

Mounting of the sink

Inserting the sink into the worktop includes a number of consecutive steps.

Preparing materials and tools

Before proceeding to install the sink, check the completeness of the sanitary product. The kit must contain all the necessary fasteners, seals. You should have at hand: silicone sealant, a tape measure, a level, a Phillips screwdriver, an electric screwdriver, an electric jigsaw, a drill.

Execute the marking

The way of marking on the countertop depends on whether there is a cardboard template. Its presence greatly simplifies the work. According to the template, cut out the outer and inner contours of the sink. It is then pasted onto the worktop, fastened with masking tape and traced with a pencil.

The template is placed on the top surface of the countertop Source remontu.com.ua

If the template is not included, it is slightly more difficult to mark the hole. First, the edges of the sink are traced, positioning the sink so that the bowl faces down. Then turn the sink over and place it on top of the countertop as it will be installed in its final position. Fix it with masking tape. Align and trace the contour. On how exactly made the marking, depends on the correctness of installation of the product and convenience of its use. Inside the contour mark a fishing line for the trimmer of the cut.

To perform the marking, it is better to use a pencil Source berkem.ru

Cut the hole

Before you cut a hole for the sink in the countertop, take an electric drill and make 2-3 holes one after another on the cut line to get a single slit. Its length should be such that an electric jigsaw can easily pass inside. Use it slowly and very carefully to cut the hole.

If the jigsaw slightly deviates from the marking line, no big deal. Allow a discrepancy of 2-3 mm. The place of the cut is cleaned from dust and the product is “tried on”. It should fit freely into the hole, but at the same time should not cling and not “walk”. If the sink does not fit completely into the hole, it is slightly enlarged with a jigsaw.

Do not turn the table top upside down while cutting, otherwise splinters might occur Source stopdacha.ru

Detailed installation instructions

Let’s see how you can install an overhead sink from “A” to “Z”, without resorting to hired installers and furniture companies.

The instructions will be useful to everyone who is used to doing all the simple household chores with their own hands, and the sink itself will find a place in the cottage or in the kitchen in the apartment as a temporary replacement.

See also  How to cut ceramic tiles without a tile cutter

Step #1. the selection of materials and tools

To assemble more quickly, the cabinet can be purchased ready-made, but only if it fits the dimensions of the sink.

The second solution is to order in a furniture company, but this option is appropriate only if the cost of the order is low.

One of the options for the finished product. However, self-made bollard has a significant advantage. an individual design, matched to a specific interior

To chip the cabinet and fix the sink to it, you will need the following materials:

  • thin boards, sheets of plywood Particle board or fiberboard;
  • steel sink;
  • kitchen faucet with connectors;
  • fasteners for the sink (self-tapping screws, corners);
  • Sealant or mounting foam;
  • hinges and handle for the door;
  • siphon with sewer fittings;
  • antiseptic impregnation;
  • legs or casters.

To fix the sink to the cabinet, you need only an electric screwdriver or a screwdriver to tighten the screws, but to cut out the walls, base and doors you will need a hacksaw, circular saw or jigsaw.

When using power tools, which significantly reduce the number of chips when cutting Woodchip board, it is recommended to use guides. so that the lines were perfectly flat

To grind the ends you need sandpaper, and to drill holes for screws you need a drill with a thin drill bit. We do not recommend the use of nails: they are more difficult to hammer into the chipboard, in addition, the construction, fastened with nails, becomes indestructible.

It is better to buy all the materials in advance, so that during the assembly process you don’t waste time looking for the right parts. The listed tools are usually available in the home workshops of amateur craftsmen, especially if they are in charge of a cottage economy.

Step #2. making the kitchen drawer

The cabinet under the sink has a design that differs from conventional kitchen cabinets. It has no two elements: the back wall. for free connection to the communications, as well as the countertop, as it is completely replaced by the sink-overlay.

Drawing with the dimensions can be taken in the public domain, although there are universal parameters: height. 850 mm, depth. 600 mm, width. 500-600 mm. A ready-made model can also serve as a sample

Sheets of chipboard, thick plywood or moisture-resistant gypsum board. sometimes it is easier to take some materials left over from the repair. take enough material to make two full walls, the bottom and the parts for the connecting “belt”.

  • First we cut out the large elements. two identical side walls and base, then the horizontal connecting parts;
  • Accurately make the cut and if necessary, clean up and process the edges;
  • If we use planed boards or plywood, before the assembly we need to impregnate all the elements with antiseptic impregnation, varnish or paint;
  • Connect the elements according to the drawing with self-tapping screws and metal corners;
  • on the underside of the base fix legs or rollers.

If possible, we make adjustments to the legs. If desired, the space under the drawer can be closed with a plank. Lastly we hang the door. This is better to do after installing the sink.

To fix the hinges, we take a drill with a suitable diameter drill bit and drill two holes. at the top and bottom. Try not to let the bit penetrate the panel

The carcasses (cross bars) are recommended to be placed directly under the sink and at the bottom. You can also make additional crossbars in the middle, if the design is voluminous.

After assembling the construction, check its strength. Install it in the place you’ve selected, preferably as close as possible to the service lines.

Step #3. Choosing the right sink

Metal sinks for overhead use are sold in plumbing stores, and can also be found in the dacha departments. They are similar, but may differ in design and size.

In addition to single sinks, representing a traditional rectangular or square product with rounded corners of the bowls, there are models with shelves-dryers, which is convenient to put washed dishes, vegetables or fruits.

Selecting the size, you need to consider the dimensions of the cabinet, if it is already ready. In the opposite case, the sink is chosen according to need: single or double, with or without a dryer.

If you need to soak your dishes, it would be better to buy a sink with two compartments. It will also be appropriate for large families, when an additional compartment is needed to accommodate large amounts of dishes or washing vegetables

Check if the bowl has an overflow, an insurance against flooding, as well as a circular shaped grid for the drain opening to trap coarse debris and food debris

The metal of which the sink is made can be shiny (traditionally “steel”) or matte. In terms of technical characteristics, both options are the same.

Next, let’s look at how best to attach the overhead sink to the kitchen drawer.

Step #4. Installing the faucet and siphon

When the cabinet is assembled and adjusted, we can say that the most difficult part of the work is over. It remains to fix the sink, pre-fixing the mixer and siphon on it.

First you can put the faucet, using the fasteners and gaskets that come with.

How to embed a sink in the countertop. let’s work on the glory

Tools needed

In this article we deal with how to embed the sink in the countertop, and if you join us, it means that you have a change in the kitchen and would like to try yourself as a master. Well, let’s try to consider in detail all the pitfalls, not only to carry out the installation, but also to ensure the durability of your new purchase.

See also  How to cut a hole in a ceramic sink

1 Mounting a sink to the countertop. why we choose a sink that is embedded?

There are two ways to organize a sink in the kitchen. overhead and inset. In the first case, along with the dishwashing bowl you also get a pedestal or a pedestal, on which it is placed. And in the second case, the installation of the sink in the countertop of your kitchen set. often the customers prefer the plunge-in variant, though it is more troublesome to install, but it still has a number of advantages, which make us choose it.

The first and most important argument against the overhead sink is the constant moisture in the kitchen, which is formed between the cabinets adjacent to the block with a sink. Users then go on to argue that there are different ranges and aesthetics of inset sinks. Here most often you can find a wide choice of both materials and forms. Ceramics, porcelain stoneware, stone, plastic, stainless steel, copper, bronze. an enviable list, though? And if you diversify it with round, rectangular, angular and various asymmetric shapes, then the eyes will run wild.

Thinking about how to embed the sink in the countertop, you should keep in mind that it can be installed in three ways: exactly at the level of the countertop, slightly below and slightly above. It depends not only on your desire, but also on the configuration of the purchased set. Specify how the bowl should be positioned, what fasteners are used for installation. Also think about how strong they are, and what can affect their life, because sometimes the quality of the sink is good, but it is attached almost on an honest-to-goodness.

2 How to insert the sink into the countertop and prepare for the operation?

Before you deal with how to install a sink in the countertop, you should make sure that you have a reliable supply of water to the place of attachment and also a quality sewage system. From the strategically important tools that will need to look for your friends, perhaps more than one day, if you personally do not have them, you can bring a jigsaw. Without it, to start the work senseless. From purchased materials except the sink must be present sealant, preferably a transparent silicone.

Buying a sink, you can get a pleasant surprise. a template for its mortise (it acts as its packaging), otherwise you will have to draw it on the countertop, applying the sink. Also do not forget that if the kitchen unit is brand new, there are no holes for the pipes, and, in fact, as the pipes themselves, perhaps. That is, the siphon and related hoses are purchased on their own, they are rarely included in the set of sinks.

If you are just assembling the furniture, and you have the opportunity not to fasten the countertop lid yet, then do not do so. It’s more convenient to cut out this way.

How to embed the sink in the countertop, you can be advised by many, but it is difficult to remember and implement everything, so watch the video and refer to our article

[content-egg module=GdeSlon template=compare]

) Fixing the sink with screws on the couplers.

Once you’ve made sure that the sink will be tightly clamped to the screed, you can proceed to complete the installation. At this stage, we can recommend that you immediately install the faucet into the hole on the sink and connect the hot and cold water hoses to it. It’s easier to do with the sink off than later on in an awkward position and lack of space. Before lowering the sink in the prepared aperture, it is necessary to loosen the screws of clamps (counter-clockwise), so as not to damage them against the edge of the countertop. Then the work will be done under the sink (under the countertop):

A tightly fitted sink can be evaluated visually, the gap between the edge of the sink and the countertop should not exceed 1mm (if the gasket allows). On this the installation of a steel sink is considered to be finished! If you have any questions, we are always happy to answer them in the Комментарии и мнения владельцев or on any of our other contacts.

Sinks of stainless steel: round and oval, in Khabarovsk.

Steel kitchen sinks today, perhaps, take the first place among all types of sinks for the kitchen. Sinks are made of stainless steel and have different thickness (1.0,6 mm) and of different.

Desk pull-out sink extension 60mm with USB (drawing, dimensions, parameters)

Extendable recessed extension cord with USB port to power low-voltage devices. Parameters, classification, allowable usage and detailed drawings of the unit (see. picture below).

Table retractable mortise extension 60mm (drawing, dimensions, parameters)

Retractable (vertical) recessed round extension with sockets. Parameters, classification, acceptable use, and detailed drawings of the device (cf. image below). extension.

Shoe cabinet swivel (installation instructions and drawing)

Mounting and fitting dimensions for installing (assembling) furniture shoe boxes. The standard set for making folding shoeboxes includes 2 sidewalls, swivel mounts and stops. Kark.

| Denial of responsibility | Contacts |RSS