How to cut moldings from a composite. Than cutting ecopolymer?

Than cutting moldings?

Polyurethane and gypsum moldings are cut with a hacksaw for metal. Foam can be cut without a bin, just with a mounting knife. Important: in all cases you can use a hacksaw for metal. Small and frequent teeth guarantee a flat and accurate cut.

The canvas of the hacksaw during cutting should move from right to left. We also make a trim of the right skirting board, only placement in Stusl and the direction of the hacksaw we make mirroring the left. The trimming of the outer corner is made in a similar way, only on the lower face of the molding we note the place that falls on the angle of the wall.

How to cut polyurethane moldings?

For this, a stamp is used. In both cases (when installing on glue and on self.tapping screws), the ends of two corner planks must be glued. This is best done before installing the skirting board in place. At the same time, it is worth using glue designed for joints from polyurethane.

  • Take measuring tools, for example, roulette, and pencil
  • Apply molding to the ceiling surface and mark the dimensions;
  • Prepare a knock and a hacksaw for metal
  • Keep a tick with your hand and select the position of the hacksaw in which the corresponding angle of connection will be set.

Now you need to study in detail how to cut an angle on a ceiling plinth.

With a stall

45 degrees skirting boards are much easier to cut in Stusl. Do not try to try on, work for “maybe”. All inclinations are already clearly displayed on the template. By the way, it can be done independently. Here is an instruction for a simple one.time template.

Internal angles

Before cutting a ceiling baseboard in the corners, measure the length and put a mark. Put the rail in the knock also how it will be attached further.

Squeeze it to the far from the wall of the template and hold it with your left hand. Find the slot responsible for 45 start sawing. Cut the second rail in the same way, only now hold with your right hand and use the second slot on the same side.

Now you can dock the ceiling baseboard in the corners. The walls can be littered and their angle will not be even. Then just remove excess material with rough sandpaper or construction cutter.

That’s all, now you know how to correct the ceiling baseboard at the inner corners.

Cut start from the outer part of the molding. Saw at the output tears the edge and remove the burrs to remove.

External sections

Meanwhile, how to cut a ceiling plinth in the corners of external and internal differences a little. Change only the location of the strip of molding, as in the picture.

When there is no

How to correctly cut an angle on a ceiling plinth, if there is no factory? In principle, this is possible, but the accuracy will be limp.

We mark the ceiling

Before cutting the corners on ceiling moldings, mark the wall.

As a pattern, take the molding so that the intersection label gets clearly into the center.

Cut the corners

And so, it’s time to cut off the baseboard. Apply molding to the wall, joining it with markings. The perpendicular fishing line for the trimmer falls on it. this is the intersection point. Draw lines from it to the opposite corner of the rail.

It remains only to cut off the angle of the baseboard. With the 2nd rail, you need to repeat the same procedure.

The plus of this method is that there is hardly no need to join the corners of the ceiling plinth. Even if the slope is not perfect, the point will fall exactly to the area that needs to be cut.

Overlays

In general, you can not suffer at all with the search for angles. It is quite acceptable to buy overlays.

The corners for the ceiling skirting boards from the foam are glued to the site of the walls of the walls.

On their sides they have even planes where you need to glue the ceiling plinth, and you will not need to cut the angle. True, this is not appropriate in any design, and it is difficult to find them in stores.

They have another advantage: if you cut off too long stripes, the baseboard in the corners must be cut at 90, so “not to get” will be more difficult.

You have already learned about how to correctly cut the ceiling skirting boards in the right corners, but non.standard situations also happen. They are found if there was a redevelopment in the apartment, but you did not take into account the molding.

So how to correctly cut a ceiling plinth in indirect angles? There are several recommendations.

Stupid

Dumb name is a slope of more than 90 about. Often it occurs on the protruding parts. Do not even try to find such a slope on Stusl, because in factory models it is not done. A professional saw for corner cuts is suitable, but few people have it at home.

Since make the outer angle of the ceiling plinth even? If the polystyrene molding, just heat it with a hairdryer.

From the temperature it softens and you can give it the necessary shape.

Do not try to cut the corners of the ceiling plinth correctly, it is very difficult to catch the desired slope.

Sharp corners are fitted similarly. Before gluing the ceiling skirting boat from foam. warm the corner and form the desired slope.

Rounded

But how to make a “round” angle on the ceiling plinth correctly? It is harder here, because the foam cannot be warmed up to such plasticity. The only option is to crush it into small parts and glue the ceiling plinth in the corners like that.

Here it is worth considering that at the back of the molding there are often stiffener ribs that do not allow him to go around circles in the necessary form. Therefore, even in small areas, it is better to cut them several times by the longitudinal line.

If the rounding is small, you can cut into such parts.

But in this case, so that the joints are more or less even, cut the corners.

With plastic molding is still easier. It is enough to do the slots on the back edge in this way and bend.

A similar technology works with wooden molding. It must be cut into several cones and collect roundness.

How to cut the corners of a wide ceiling plinth?

Install the strip of the baseboard in the knock so that this position exactly coincides with the placement on the ceiling. The skirting board should be tightly pressed against the opposite wall. Hold and press with a free hand. Put a hacksaw at an angle of 45 ° in a special hole and cut off the part.

  • Special adhesive compounds on a polymer basis. The most common are glues the moment and titanium
  • Liquid Nails. If you want to know what it is better to glue the ceiling skirting board for, then this option is the best option
  • Acrylic.based putty.

How to cut a ceiling plinth at home?

The bar is applied to the ceiling, the size is made in size. Holding on his left hand, the ceiling baseboard is pressed against the closest wall, the knife handle gets closer to the hand. The workpiece is cut off. The response bar is pressed against the nearest wall, while it holds it with the right hand.

As a rule, to make a corner of the ceiling skirting board from PVC, you can use a sharp stationery knife. Bagets made of denser materials can be cut with a saw or hacksaw, but it is best to use a special carpentry tool. a stupid, which is a groove with slots.

How to cut the ceiling plinth correctly. Important little things

Measurements necessary for pruning the baseboard on the ceiling should be done in a special way. To determine and mark the inner angle, the length should be measured from the corner. For the mark of the outer angle, it is necessarily taken into account that in deeper the room the skirting board will protrude at a distance that equals its width.

moldings, cutting

It is not advisable to fix the planks of skirting boards before the moment when their exact location is tried on and the response skirting is cut off. Only after the ideal converging in the corner of both response planks can they begin to install them and fasten. If the work is carried out with polyurethane or wooden skirting boards, defects and flaws can be fixed with a file or file. To adjust the product from foam, you should arm yourself with a sharp knife.

If even after finalizing the skirting boards there remains at least a small gap, do not rush to be upset. it is easy to close up with ordinary putty. Cutting accurately and neatly ceiling skirting boards is not so difficult. But to purchase at least a small skill, first try to practice on small blanks.

How to correct the corners on ceiling skirting boards of various shapes

Tip: instead of a saw that is attached to the strap, it is better to use a regular hacksaw for metal. Its cut is more accurate and even more, which is very important in this process.

Before starting work

The choice of the correct width of the baguette is the key to a beautiful interior. An important role in the sawing process is also played by the method by which you do this. We want to give you a couple of recommendations that will help to achieve their plan.

99% of people don’t know this about a miter sawDO YOU??

So, how to choose the width of the material and how to cut the ceiling baseboard in the corners:

  • The prepared surface of the walls is not a standard of evenness, use planks of smaller width, as they are more flexible and will be able to close the maximum number of defects. Accordingly, the opposite, the more perfect the surface, the larger the width of the molding can be, however, keep in mind. mount a narrow baguette in rooms with low ceilings so as not to reduce them visually;
  • Always apply the left side of the corner to the stitches while dripping on the left, the right. on the right. In addition, it should be the side of the tool closer to you, distant. for floor moldings. Please do not confuse.

How to cut the corners on the ceiling of the baseboard under 45 degrees

Below we will deal with the set task, where you will find out. how to cut the corners of the ceiling plinth correctly and with the greatest quality.

External

There is one nuance of this process that you should never forget about. We always look at the ceiling below, therefore, when the bar is placed in the knock (to the wall closer to you), it must be turned upside down.

The upper part of the molding will then have below, and the lower, respectively, at the top. Thus, there will be no gaps between the planes of the angle when they connect.

In the photo. a knock, a carpenter tool in which the corners of the ceiling plinth is cut

  • Take measuring tools, for example, roulette, and pencil. Start marking from the inner angle, so you will not miss the external. It may happen that there is not enough baguette length and you have to do many joints;
  • Apply molding to the ceiling surface and mark the dimensions;
  • Prepare a knock and a hacksaw for metal. Press the baguette to the instrument near your side;
  • Keep a tick with your hand and select the position of the hacksaw in which the corresponding angle of connection will be set. These can be standard parameters. 45, 90, or 135º, or arbitrary, for which it is necessary to push the knock into the chosen degree;
  • Cut the workpiece with a hacksaw;
  • Install the opposite bar to the near wall of the tool and fix it with your hand;
  • Put the chosen degree on stuplet and cut the workpiece with a hacksaw for metal;
  • Coasten the resulting plinth planks.

Tip: if the walls are interconnected at a right angle, only in this case you will help you in the work of the knock, otherwise you will have to fit your own hands.

Interior

There is a professional knock, which has a rotary platform and can be extended to obtain arbitrary angles, as well as for home use, where special opportunities are limited. Usually in the repair it is enough to use the second option.

How to cut a ceiling plinth in the corners without gaps

So, the basic principle. ceiling strips are cut off at the closest wall of the tool, we hope you have not forgotten.

  • Measure the required baguette length, applying it to the ceiling surface;
  • Put the barbood bar in the knock, while its position should fully correspond to the location of the baguette on the ceiling;
  • Press the bar to the near wall of the tool;
  • Select the corresponding degree of the cut, most often it is 45. Make sure that the knife handle is as close as possible to the hand holding the bar to make the cut as accurately as possible;
  • Cut the workpiece, but do not apply unnecessary efforts to a hacksaw;
  • Prepare and cut off the opposite baguette bar, not forgetting that it should be pressed against the near wall;
  • Select the corresponding angle of the cut for it, leaving a minimum distance between the knife handle and the hand holding molding;
  • Cut the edge of the bar.

It remains to check the correctness of the docking of the segments, and if everything corresponds to expectations, install them in place.

Tip: Start cutting from the front of the molding, then you can orient it on the spot as accurately as possible. The corners of the wooden baguette after cutting, treat and adjust the file.

How to cut the corners of ceiling skirting boards with a hacksaw and

How to make the corners of the ceiling baguette without rushed

For the first time deciding to make a frame on the ceiling, the beginner does not see any problem in this, but in vain. We advise you to immediately take into account the cost of a certain amount of material, which will just have to be thrown away.

Alas, at what angle to cut the ceiling baseboard depends only on the connection of the walls with each other. Not everyone corresponds to direct, for which it is enough to simply cut off the bar under 45 °. Often there are parameters corresponding to 85 or 95 degrees, but this is already a problem for beginner finishes.

How to cut a plinth in the corners of a ceiling plinth without the use

If you are the owner of an apartment built in the last century, this was generally considered the norm. The fact is that when you simply cut off the bar under 45 ° and install on the ceiling, there will be gaps between them, which will then have to be sealed with sealant or putty. We will try to help you solve this problem with minimal costs, since the price of not every molding penny.

moldings, cutting

So, how to correctly cut the corners of the ceiling skirting board for the inner angle:

Training Prepare a tool that will need to work.

How to correctly cut off the ceiling baseboard at an angle of 45 °

Coal elements for ceiling skirting boards are easily cut on stizl and manually. In the first case, you will need a knock and a hacksaw, and in the second. a pencil and a hacksaw/knife on the cardboard. The hacksaw canvas should be well imprisoned so that you do not have to think about how to smear chips and roughness on the cut.

Cut the angle with the help of

We take a polyurethane ceiling baseboard designed for the left or right side of the corner. We lean him against the future place of installation so that the end of the segment opposite from the corner to the edge of the already glued molding. In the place where the lower edge of the ceiling baseboard is in contact with the top of the angle of the wall, put the point with a pencil or stick a piece of insulating tape. Repeat these actions with the second segment.

How to cut a ceiling plinth on the inner corner? Everything is very simple, the actions will be exactly the same, only the location of the tag of the corner changes. Here, on the contrary, for the left segment is the extreme right slot, and for the right. the extreme left. The finished ceiling fillets must be combined, and then look at the joints to the light. there should not be cracks. If they are very small, then the editing is not needed, you can do with putting with putty material after installation.

How to make an angle of ceiling plinth: the location of the workpiece in Stusl

Important: sometimes the corners have too large deviations from standard 45 degrees, and a simple knock for a ceiling skirting board becomes useless. you can cut excess. The output will be the purchase of a rotary tool, but it is not cheap and this acquisition “at a time” will be irrational. In this case, you can do with the method of intersecting points.

How to cut the corners of the ceiling skirting board without a bin

If you think about how to properly cut a ceiling plinth without a bunny, then the next information will be useful to you. We take the right segment of the ceiling plinth of foam, apply to the place of installation and draw a fishing line for a trimmer on its upper edge on the ceiling. She should go beyond the points of the vertices of the angles by about 5 cm. We do the same with the left segment and put points at the places of intersection of lines. Ceiling skirting boards alternately apply in place and transfer the resulting marks to them.

With the upper part of the ceiling moldings, we figured out, now we go to the bottom. Everything is simple here, the marks we need. these are the tops of the corners. We note their location with dots on the lower edges of the left and right ceiling plinths. Next, you need to connect the points on the moldings. this will be a line of trimming. This method will help to cope even with the most curved angles. The fit is most likely not needed, and if this happens, then it will be minimal.

How to cut off a ceiling plinth without a special device: the photo visible notes for the method of intersecting points are visible

Important: the work described here requires to set marks on the surfaces. Therefore, first you need to proceed to the clipping and fitting of the ceiling skirting board, and only then think about how to glue wallpaper. Or, if you want to fix the baseboard on top of the wallpaper, make the marking and trimming before the finish, and the gluing after it.

Cut the internal and external angles of floor skirting boards

It is no more difficult to cut floor moldings evenly than ceiling. Only the cutting tool is selected according to the material that we will saw. The work itself will also be similar, only for manual cutting a slightly different marking method is presented here.

Cutting wooden floor molding using

It is necessary to measure the distance from the edge of the baseboard already glued to the wall to the top of the angle of the wall. Now we take a new segment of the molding and put off on its lower edge the length equal to this distance. Put the point with a pencil or glue a piece of isolation. We do this procedure for both external and internal angles. In the stuplet, we place the segments of the baseboard from left to right for the left side of the corner and right to left. for the right. At the same time, they should be pressed as in the figure. to the side of the stir, neighboring to yourself.

How to cut the angle of ceiling plinths. laying the workpiece into the knock:

  • For the external left, compare the mark on the skirting board with the extreme left slot. For the external right. with the extreme right.
  • For the inner left, compare the mark on the skirting board with the extreme right slot. For the inner right. with the extreme left.

Clarification: The slot is meant the one that is on the side that is closer to you.

Subscribing the skirting board at an angle: a red lines marked the place of cut

Floor skirting board: the inner and outer corner “by hand”

Moldings for the floor, as a rule, are quite wide and thick, and therefore here is only two points by finding, as for ceiling baguettes, you can not do. To cut the inner corner, we first set the point at a height equal to the width of the skirting board at its top. in the figure it is a green point. From her left and right we put off a distance equal to the thickness of the plinth. points 1 and 2.

We apply the left segment to the wall, and from point 1 we draw a fishing line for a trimmer, perpendicular to the wall and put a point on the edge. Repeat the action with the right segment, only draw from point 2. In the figure, the point is marked with the number three. From it across the baseboard we draw a fishing line for a trimmer to its opposite edge. we get point 4. Now we connect the green point with points 3 and 4. we get a fishing line for a trimmer and a corner along which it will be possible to cut the molding.

How to cut a plinth: the necessary notes are made in the corners

Important: pruning the outer angles is easier to do than internal. On the left and right segments we set the points: a. a mark of the top of the angle of the wall; C. the point of intersection of the lines, which is obtained by alternately drawing the left and right segments of the skirting board on the floor; B. from the point C across the molding, a fishing line is carried out for a trimmer to its opposite edge.

By connecting these points to each other with one line, we get a fishing line for a trimmer along which a cut will be made.

The tools used

First, how to cut a ceiling skirting board from polymers or wood, how to make it correct and quickly. In this case, 2 tools will be required to work. a knock and cutting tool.

Than cutting skirting boards?

As for the latter, the choice depends on the material of the plinth:

  • Foam products (all polystyrene) suggest the use of a sharp stationery knife;
  • Polyurethane skirting boards are usually cut with a hacksaw for metal;
  • The tree requires the “active” participation of a jigsaw or saw.

The second potential tool for polyurethane is the same stationery knife. The reason is a fairly low density of the material. Another alternative is a sharply sharpened kitchen knife. A special requirement for him is not a too thick blade.

Possible replacement of a jigsaw for wood. a hacksaw for metal. Optimal canvas with the smallest cloves. Otherwise, the gun will get stuck in the material, and in such conditions it is extremely difficult to make an impeccable sharp.

Making Perfect Crown Mold Miter Cuts

Knock and its independent manufacture

Knock. the second mandatory tool for working with skirting boards.

What it is?

Not everyone can know what it is. This is a device that makes it possible to cut any blanks at different angles (45-90 °). This is a groove consisting of a bottom and two side sides in which instruments are made for tools. The material is laid on the bottom, and a hacksaw is inserted into the slots (knife, etc. D.). After cutting the baguettes with it, they receive almost perfect blanks.

Fetling is the need for pruning any skirting boards, since the joints of the elements require an angle of 45 °. Otherwise, the connection of the parts will not work: either the gap will remain between neighboring skirting boards, or they simply need to be cut again, since it will be impossible to dock neighboring products.

Yes, the remaining hole can be disguised as any composition. However, this option is still not the best. The aggregate will soon change the color slightly, and this discrepancy will become very noticeable. However, even here there is an exception.

How to make a knock?

For self-manufacture, you will need to find a board about a meter or more long, or a sheet of plywood (wood-bruise). You still need to prepare:

  • 3 parts with a width of 200 to 250 mm are cut out of the selected material, their length is 300 mm (400, 500 mm). Using self.tapping screws, they are connected in the form of the letter “P”.
  • Using the transporter, marks are made on the upper parts of the sidewalls corresponding to the angle of 45 ° (if necessary, then 90 °).
  • Then take a hacksaw, which is drank holes so that the grooves reach the bottom of the tool.

Ready.made holes are pulled by rashpil so that a jigsaw or a hacksaw can freely enter them.

How to cut a ceiling plinth?

The answer depends on what angle we are talking about. Internal and external docking are slightly different.

Internal angles

The easiest way is to work with a stupid, but there is an opportunity to cope without this tool. In this case, the fishing line for the trimmer of the angle of the cut (45 °) is drawn using the transporter. The second option is to apply the skirting board to the place where it will be, and a tank of cutting points.

45 ° cut is not the only operation. So that both elements are able to do without problems, they make a small bevel on their outer side. This stage requires repeated fitting both blanks, since such a correction can only be done by eye. Plinking boards made of polymeric materials are cut with a sharp stationery knife. For wooden baguettes, not a hacksaw is used, but another tool: it is better to create begging, wiping the edges of the products with large rashpil.

External angles

In this case, the difference is that you will have to grind not the outer sides of the planks, but the internal parts. Otherwise, the procedure is no different. First, with the help of the casket, slices are made at an angle of 45 °, then both blanks are sent for fitting. to the wall, then they carefully make a bevel on the inside.

If the outer angle of the wall follows at a small distance from the internal, then often another problem arises. She is the selection of the length of the workpiece. Here we need maximum accuracy, so you have to make multiple fitting, since the rule about “Seven times measure” works here.

Incorrect wall geometry is another obstacle that is difficult to get around. Their unevenness is one of the most common problems. In this case, the baseboard is applied to the base, the wall defects are noted on the product, then it is additionally treated.

How to cut a ceiling plinth using aur?

This is not to say that the use of this tool makes the task elementary. The baguette must be reliably held on the spot, otherwise defects may result in a result. With a small width of the product, it must be pressed to the nearby side of.

For external corners

Before proceeding to the operation, a cut (45 °) is done on the workpiece.

  • The tool is fixed in the most convenient position. This preparation gives a chance to accurately determine the position of the plinth. Rather, that of its edge, which will have to be at the ceiling. As a rule, right.handed workpiece is placed on the right, and left.handed work on the left.
  • The skirting board is pressed to the lower and side sides of the rushed so as to avoid any of its movements. They start to do it from themselves.

After completing the work, both blanks are applied to the corner (without adhesive composition), check the coincidence of parts. If you need to adjust, then it is made with a knife.

For internal corners

In this case, it is first determined which surface of the bar will be “adjacent” to the ceiling.

  • She is put on the bottom of the tool.
  • The other side is pressed to its neighboring wall.
  • After the sawing is completed, the strips are checked at the place of their subsequent fixation. If necessary, then they also carry out adjustment.

The last stage of work is the gluing of the skirting boards. If there are small gaps, then they can subsequently be closed with a suitable material.

How to do work with a drawn.drawn?

Using “struck without a bunny” is another answer to the question of how to cut a ceiling baseboard. Paper, cardboard or rather large wooden board are suitable for the role of the template. First, three parallel lines are drawn on the material, then the square is drawn, then its corners are connected with diagonals, receiving angles 45 °.

Since far from all houses and apartments, the walls have absolutely correct geometry, in this case, for the accuracy of the cut, you first need to check the issued angle. If the walls do not correspond, then the use of a normal tool, you need to completely refuse. It will be successfully replaced by a home.made paper (cardboard) device.

How to cut the edges without a bunny?

If there is no desire to make a homemade plinth, that is, an alternative option. But in this case, the result will depend on the accuracy of work. The operation consists of several steps:

  • Apply the first bar, then on the ceiling at the corner with a pencil, a fishing line for a trimmer is carried out;
  • This skirting board is removed, then the opposite workpiece is also applied, which is also noted;

Despite the lack of a special tool, the quality of work does not suffer, but in this case the accuracy and impeccably executed sections are important. Work on the workpieces for the outer corner is carried out similarly, but in this case the lines are drawn (and continue further) from it.

An alternative to cutting skirting boards

If there is no desire to carry out an independent docking of workpieces, then you can use a simpler solution. to purchase special corners that greatly facilitate this stage of the operation. However, this option is not always available. The reason is the limited range of such products. You can pick them up far from every skirting board.

How to cut a ceiling plinth?

The answer depends on what angle we are talking about. Internal and external docking are slightly different.

Internal angles

The easiest way is to work with a stupid, but there is an opportunity to cope without this tool. In this case, the fishing line for the trimmer of the angle of the cut (45 °) is drawn using the transporter. The second option is to apply the skirting board to the place where it will be, and a tank of cutting points.

45 ° cut is not the only operation. So that both elements are able to do without problems, they make a small bevel on their outer side. This stage requires repeated fitting both blanks, since such a correction can only be done by eye. Plinking boards made of polymeric materials are cut with a sharp stationery knife. For wooden baguettes, not a hacksaw is used, but another tool: it is better to create begging, wiping the edges of the products with large rashpil.

External angles

In this case, the difference is that you will have to grind not the outer sides of the planks, but the internal parts. Otherwise, the procedure is no different. First, with the help of the casket, slices are made at an angle of 45 °, then both blanks are sent for fitting. to the wall, then they carefully make a bevel on the inside.

If the outer angle of the wall follows at a small distance from the internal, then often another problem arises. She is the selection of the length of the workpiece. Here we need maximum accuracy, so you have to make multiple fitting, since the rule about “Seven times measure” works here.

Incorrect wall geometry is another obstacle that is difficult to get around. Their unevenness is one of the most common problems. In this case, the baseboard is applied to the base, the wall defects are noted on the product, then it is additionally treated.

How to cut a ceiling plinth using aur?

This is not to say that the use of this tool makes the task elementary. The baguette must be reliably held on the spot, otherwise defects may result in a result. With a small width of the product, it must be pressed to the nearby side of.

For external corners

Before proceeding to the operation, a cut (45 °) is done on the workpiece.

  • The tool is fixed in the most convenient position. This preparation gives a chance to accurately determine the position of the plinth. Rather, that of its edge, which will have to be at the ceiling. As a rule, right.handed workpiece is placed on the right, and left.handed work on the left.
  • The skirting board is pressed to the lower and side sides of the rushed so as to avoid any of its movements. They start to do it from themselves.

After completing the work, both blanks are applied to the corner (without adhesive composition), check the coincidence of parts. If you need to adjust, then it is made with a knife.

For internal corners

In this case, it is first determined which surface of the bar will be “adjacent” to the ceiling.

  • She is put on the bottom of the tool.
  • The other side is pressed to its neighboring wall.
  • After the sawing is completed, the strips are checked at the place of their subsequent fixation. If necessary, then they also carry out adjustment.

The last stage of work is the gluing of the skirting boards. If there are small gaps, then they can subsequently be closed with a suitable material.

How to do work with a drawn.drawn?

Using “struck without a bunny” is another answer to the question of how to cut a ceiling baseboard. Paper, cardboard or rather large wooden board are suitable for the role of the template. First, three parallel lines are drawn on the material, then the square is drawn, then its corners are connected with diagonals, receiving angles 45 °.

Since far from all houses and apartments, the walls have absolutely correct geometry, in this case, for the accuracy of the cut, you first need to check the issued angle. If the walls do not correspond, then the use of a normal tool, you need to completely refuse. It will be successfully replaced by a home.made paper (cardboard) device.

How to cut the edges without a bunny?

If there is no desire to make a homemade plinth, that is, an alternative option. But in this case, the result will depend on the accuracy of work. The operation consists of several steps:

  • Apply the first bar, then on the ceiling at the corner with a pencil, a fishing line for a trimmer is carried out;
  • This skirting board is removed, then the opposite workpiece is also applied, which is also noted;

Despite the lack of a special tool, the quality of work does not suffer, but in this case the accuracy and impeccably executed sections are important. Work on the workpieces for the outer corner is carried out similarly, but in this case the lines are drawn (and continue further) from it.

An alternative to cutting skirting boards

If there is no desire to carry out an independent docking of workpieces, then you can use a simpler solution. to purchase special corners that greatly facilitate this stage of the operation. However, this option is not always available. The reason is the limited range of such products. You can pick them up far from every skirting board.

Several recommendations

Any work has nuances, but they cannot be perceived with trifles. In order for pruning to go carefully and without problems, you need to pay attention to several points.

  • Correct measurements. the most important thing in any work. To mark the blanks for the inner angle, the measurement begins precisely from it.
  • Before cutting off both planks for the outer corner, they do not forget that for it they will “peek” for a length equal to the width of the products.
  • Fixation of ceiling baguettes begin only after several checks carried out. When the edges of the skirting boards are perfect, then you can start gluing them (with self.tapping fastening).
  • To correct the connected blanks, you can use files or files. For polystyrene and both types of polystyrene foam, it is necessary to take thin, sharply bidders.

Since any debut rarely passes without errors, it is recommended to start with training on scraps. Therefore, when buying it is better to add 10-15% to the length of products. So it can be guaranteed that the material is enough not only for preparation, but also for the entire room, even if the flaws still appear in the process of work.

How to cut a plinth of polystyrene?

Cutting such a plinth is most convenient with a hacksaw or a sharp building knife. Polistyle foam products are also inexpensive, although this material is a more strong analogue of traditional foam. It is also processed by a sharp tool.

Most often, for cutting the skirting board, a regular hacksaw for metal is used, which has small teeth. However, it is not suitable for thin skirting boards, since the product will simply break under the influence of this tool. Sometimes a baseboard is cut and scissors for metal.

How can you cut a plastic skirting board?

manual jigsaw. But I usually use a hacksaw for metal, in my opinion, the most optimal option. Some ceiling plastic skirting boards can be cut out qualitatively even with an ordinary building knife. Even the floor skirting boards with a cable channel cut with such a knife, but the hacksaw is still better.

Conclusion: “Liquid nails” are a good alternative to all methods of attaching ceiling skirting boards. The fillets recorded with their help receive reliable, longend clutch with the base (wall or ceiling).

| Denial of responsibility | Contacts |RSS