How to cut tint on front windows

Preparatory stage

Before you begin directly tinting the windows, you’ll need to choose the right film. It should be noted right away that it is highly undesirable to use the cheapest Chinese film, because it is not recommended. к. its service life will not be very long. Over time, this material burns out in the sun, and the adhesive layer leaves much to be desired. It is either too weak or, on the contrary, too sticky and its residues will be very difficult to remove in the case of removal of tinting.

expensive films from reputable manufacturers have optimum thickness, do not lose color in the sun, and can last for many years.

Do not also forget about the light transmission capacity of the film, because if you do not take into account this point, you can get serious problems when passing the technical inspection or inspection of the traffic police. For instance, any films may be used for tinting rear windows, except for those with a mirror effect. As for the front side windows, they should be able to let in at least 70 percent of the light. As for the windshield, the figure should be at least 75 percent.

The tinting of your car must be done in a clean room with a good source of light and normal humidity. It is also useful to find an assistant, in order to minimize all the risks. Before starting the process, the car should be thoroughly washed, paying special attention to the windows. The surface must be flat, without dust, chips and deep scratches. If you plan to tint the door windows without removing them from the car, you will need to remove all the seals.

Tools and materials for creating and gluing the film

You can make tinting for auto windows by yourself, using special consumables. You will need a sheet of polyester (PET) no more than 0.5 mm thick and a film to be applied to the plastic. The following set of tools is also necessary:

  • a knife with interchangeable blades;
  • a pencil to draw the contours;
  • metal scissors;
  • Burners to smooth out the irregularities on the slate;
  • sprayer for applying soapy water to glass surfaces.

tint, front, windows

Fade can be purchased in a store of construction goods or products for outdoor advertising In addition to tools and materials, you must first prepare a cleaned and smooth surface, on which the plastic will be applied to the film. For this purpose you can use 15 mm thick glass.

Problems and their solutions

In the process of gluing, especially for the first time, it often happens a number of problems that can catch you unawares. To avoid this, it is important to quickly and correctly respond to them and make the only right decision.

What are the undesirable phenomena of the car tinting??

Air bubbles

It may happen that while tinting a car, air-filled bubbles remain under the film. In this case, you can take at least two ways. To the first it is advisable to resort to in the case when the film was pasted very recently.

This aspect is not decisive for the second method. So, in the first case, you should arm yourself with a plastic card or a construction eraser. The essence of it is the following: you need to press smoothly on the glass in the unfortunate place and try to squeeze the bubble out, pushing it to the edge of the glass.

The variant assumes use of a building hair dryer. It fully copies the previous method with the only deviation. squeezing the bubble is accompanied by local heating of the film.

Creases

Let’s talk about creases and how to fight them. The tint film often loses its original appearance if stored carelessly. There are characteristic “wrinkles” or creases on its surface.

To get rid of them it is enough to dip the film in warm water. After a few minutes it should be spread out on a smooth surface and straightened.

Window Tinting: Cutting film 101

Stripes

Sometimes very unpleasant phenomena are observed on the tinting film. stripes and stains. It may be caused by bad quality coating. In such a case there is only one way out. to put the glass back on again.

In some cases, this phenomenon is solved by careful cleaning of the toning with detergents. But the probability that it will help is very low.

Dots

In addition to stains, spots may appear on the surface of the film, most often of white color. The reason of their appearance is very banal. particles of dust, ashes from cigarettes, etc.п.

It is impossible to get rid of such a mistake. In order not to encounter such a problem, you should be more careful when tinting your car.

See also  Hand tool for cold forging with your own hands

How to tint your own car

Many drivers, buying a car, try to put a toning film on its windows. Passengers feel more comfortable in a tinted car because the tinted glass hides them from the eyes of passersby and protects from the sunlight in the hot summer weather.

Having decided to tint your car you can simply take it to a specialist. But nevertheless it is possible to do it with your own hands, that is what this article is about.

Once you have decided to equip your iron friend with tinting, you should choose the tinting film itself, which varies in quality and price, as well as the shade of the film itself. The choice is yours.

But the degree of darkening is also important, because the darker the film, the poorer the quality of vision for the driver, which affects the safety of driving. over, in many countries, the laws concerning the degree of darkening of car windows have recently become stricter. On average, the windshield and side windows of the car must transmit at least 70% of daylight.

The tinting film is made of polystyrene of different colors that determine the color of the film itself and, as a result, the color of your car windows. The film’s external layer is usually coated with a special metallic compound that protects the film and glass from mechanical damage. It is clear that the more expensive is the film, the higher is the quality of the protective layer and the longer you will enjoy the tinting.

Gluing the tinting film

The procedure of window tinting film wrapping itself does not require any special knowledge and skills, but, nevertheless, you should be careful when doing it. The film should always be glued on the inner side of the window, i.e. on the side of the car interior. First of all it is necessary to wash glasses properly so they do not have the slightest traces of grease stains and stains. The best way to do this is with a window cleaner. The room where you are going to wrap the tinting film must be dust free and well lit. If you are going to work outdoors, the weather should be warm and windless.

The tinting film is glued to the window with the help of soapy solution, which is applied to glasses with sprayer (the sprayer, which is used for spraying home flowers, is also suitable).

To cut the film to the right size, put tissue paper or a regular film on the glass and trace the outline, then cut the paper and you will have a workpiece on which you can then evenly cut out the tinting film. The workpiece should be made with a margin of 5-10 mm, which can then be removed with a knife. Certainly, it is more convenient to wrap the glasses if they are taken off the car. But glass taking off is labor-intensive enough, that’s why you usually make tinting of glasses directly on the car.

Spray the window with a spray-gun and apply the film with the dark side to the window, gently smoothing it from the center to the edge and taking care that no air bubbles form under the film.

Smooth out the film with a rubber spatula or something similar. Pay special attention to the edges of the film, it needs to fit well to the glass and not bulge so that later on when you lower and raise the side windows the film will not wrap around. Then let the film dry. If you have a construction hair dryer, you can speed up the drying process of the film. A construction hair dryer can help in the areas where the glass has a significant bend. The film is heated up and will better conform to the shape of the curved glass.

As you can see, tinting your car windows is not such a complicated procedure, and by doing your own hands, you will save a pretty penny.

Our portal warns its readers that tinting cars is prohibited in some countries. So before you decide to get your car tinted, you should familiarize yourself with the current legislation in your country. You must realize that violation of traffic rules will sooner or later result in fines and trouble.

Glue the film on the side windows

It is best to start the process with the side windows, as their area is less, and you will be able to get a hand.

Take the blade and gently scrape the inside of the glass from top to bottom. Try to get rid of all flecks, dust, glue residues and other particles. After that, you can treat the glass with clean water from a spray gun.

If the glass is now perfectly clean in your opinion, it is time to apply the installation solution. Spray it all over the surface.

Important! Do not use ordinary water at this stage, otherwise the film will stick firmly and you will not be able to make any turns.

Professional Techniques on Hand Cutting Window Tint

Now it’s time to remove the protective coating from the film and apply a soapy solution to its sticky side. After that it is very important to make sure that no dust gets on the adhesive surface.

  • Carefully grip the film by its tails and place it on the glass.
  • With soft movements, gently smooth it out with a bouncer so as to get rid of all the bubbles.
  • Heat the glass with a hair dryer (you should start from the upper edge). This way the film will adhere well and will not come off when you lift the glass to process the underside.
  • Once again, smooth out the edging and disperse any bubbles.
See also  How to make a front adaptor for a power tiller

For 10-15 minutes the film will still be easy to move, so you can adjust it. After this time it will take its place and you will need to expel the soap solution. To do this, it is best to use a rubber spatula, moving from the center to the edge of the glass.

When we made the pattern pieces, we left some scraps that we now need to get rid of. To do this, take a utility knife and at an angle of 30 degrees to the glass make the cuts, so that the filter does not reach the edge of 1-2 mm.

After that you can once again dry the film with a hairdryer. You can start using the car after the light filter dries out completely in about 2 days.

For the windshield tinting is done in the same way, but with the rear window things are a little more complicated.

Tinting with their own hands

Tinting glasses of the car is one of the first steps of tuning a car. In fact, do the tinting with your own hands is not difficult and you can find many reports on tinting on the Internet. But a complete guide to tinting with photos and videos in one place you will not find.That’s why I decided to consider this issue in more detail and collect all the useful materials on tinting in my report.

Advantages of tinting

  • The biggest advantage of self-tinting. Saving money compared to tinting at the car service. That is, to tone the car in the service will cost about 10 times more expensive than self-tinting.
  • Tinting your windows can help you reduce the heat in the cabin by 50-60% in the summer time.
  • Tinting your car retains up to 99% of harmful UV rays
  • If you break the glass tinting keeps the broken pieces of glass, thereby protecting you from cuts.
  • Tinting protects from reflections of sun or oncoming car headlights.
  • Tinted glass hides the cabin from prying eyes.
  • Tinting protects the plastic and moldings inside the car from the sun’s rays and can crack from excessive heat.
  • A tinted car looks more appealing.

How to choose a film for tinting

The main questions when buying a tinting film are usually these: What kind of film for tinting is better? ? What’s the difference between tinting films ? What manufacturer should I choose for my tinting film? ?

At the stage of buying a film for tinting the car I suggest not to save on time and price, and it’s better to find a product with a proven manufacturer than to buy anything and do the work on tinting windows at home.

List of quality films with a certificate and guaranteed performance:

  • SunTek film by Commonwealth Laminating Coating, Inc.,
  • llumar film by Courtaulds Performes Films.
  • Sun Control film manufactured by Garware Polyester Ltd.,
  • Sun-Gard, Glass-Gard, and Safe-Gard films by Film Technologies International, Inc.
  • Johnson Window Films.
  • MSC/Solar Gard films
  • 3M” corporation films

In a package there is usually 1,5-2кв.M film, a plastic spreader for smoothing and a knife. The easiest and shortest lasting tinting film. Single-layer with a painted adhesive layer. The highest quality film for tinting. multilayer, neutral color with metal spraying.

Preparing the tool for tinting a car

All necessary supplies and tools for tinting the car:

  • Toning Film Roll (Roll usually 2 sq. m.).м. of film, enough for 4 side windows. For the side windows and the rear window you need about 3kW.м. film); Price: from 200r./ roll.
  • Rubber trowel or plastic scraper (the latter is less desirable, as it leaves microscratches). Price: 30r.
  • Shampoo (for example Johnson’s Baby shampoo). 100ml.). Or a similar shampoo or soap solution, but most importantly do not use a liquid window cleaner. Price: 100r.
  • Spray gun (for example, “Mr. muscle” without the contents).
  • A sharp office knife with a retractable blade. Price: 150r.
  • Dry rag without lint
  • Clean / filtered warm water
  • Technical or home hair dryer (not necessary for tinting the side windows, but desirable). Price: 800r.

To prepare for tinting the car

We prepare a 10-20% solution of shampoo in water and pour it into a sprayer.

I advise to start tinting your own hands with the side windows. And only after you have some experience already proceed to the rear or windshield.

Further scenario can unfold under two scenarios:1-Tuning with the removal of glass For more comfortable and high-quality tinting glass better remove. How to remove the glass in VAZ 2110 ? To suffer a little, but to receive really pleasant and useful effect.

The law and penalty for installation of inappropriate tinting

In order not to have to remove just a glued tinting at the first post traffic police, should take into account the allowable norms. According to the law, to be exact GOST 5727-88, the windshield must pass not less than 75% of the windshield!of light, and the front side windows are 70%! On the windshield, a dark strip is allowed, but no more than 14 cm from the top edge. There are no restrictions on the rear windows. The only thing is that the tinting is deaf (less than 5%)!) requires rear view mirrors to be installed on both sides (t. е. You can on all modern cars).

See also  Performing grinding work on the machines

How to Hand Cut Window Tint on the Car

Choice of percentage light transmission tinting depends on your goals and current regulations

The penalty for non-compliance with these standards is not very high. 500. Since the spring of 2015 on the Internet “frightening” information about the new law, which provides for a threefold increase in the amount of fines (at repeated 5000 p.).). At the beginning of autumn 2016 the law has not been adopted yet.

Rather popular thanks to the installers became a service to install reusable tinting. They say if they catch you with a removable film, nothing will happen. But reality shows otherwise. В 95%!In 95% of cases, the court takes the side of the traffic police, arguing that at the time of stopping the vehicle the offense had already taken place, therefore, you can be fined quite well.

Cutting out the film for the side windows

In order for the film to stick perfectly and be easy to work with, you need to cut it to size. Before you start, understand which side is the adhesive layer. It must be protected by a transparent material. It is best to cut it in such a way that it touches the glass with the inner side of the wrap. When cutting out it is necessary to take into account that the film should protrude over the glass border on 0.5-1 cm, as an extra piece can be cut off later, and if it is not enough, it will be worse.

For an accurate cut it is necessary to apply a soapy solution to the outer side. Then put the film there so that the transparent material is on the outside. Place the film so that it covers the entire surface. At the bottom it should slightly cover the seal. Next, cut the tinting film to the contour of the side seal, leaving about 1 cm to pass under the seal. Now cut off the remnants of the upper part and then slide it under the upper seal. The film should follow the contour of the glass.

If the side windows are dull and not drooping, cut the film on the contour, leaving only a couple of millimeters to spare. If this is the case, be extremely careful when cutting out the sealant, as it can be damaged. To protect the elements of the car from scratches, it is better to apply a rakel.

It is not necessary to leave the foil remnants, and it is better to throw them away at once, because they will interfere with the further work. If you have dummy windows that are bound to the body without a sealant, cut the film very carefully. The knife should be sharp, if it blunts, it can damage the film and scratch the body.

Final attaching the film to the glass

When you are satisfied that it has taken its proper place, you can begin the process of sticking it in place. You will need a squeegee and wipes to do this step. Use the scraper to gently smooth out the film, without making any great physical effort, in order to remove any soap solution and air bubbles from underneath it. Generally start at the center of the surface and work toward the bottom. In the end, if the material will be properly glued, then under it should not remain even a small air reservoir, as these bubbles look like whitish spots on the outside and are clearly visible.

Your job is to bend them to the outer edge of the glass, where they should be removed with a clean cloth. That film which you left on reserve on edges, it is necessary to cut at a level of 1-2 millimeters up to level of an external edge of a glass. If you don’t, over time it will start to stick around the edges and scuff up. But the level of the lower edge should be put under the sealing tape at a distance of about 0.5 centimeters, this will save it from possible scuffing during the daily use of windows.

After all these operations, the work of fixing the tinting film on the car windows can be considered quite complete. Finally it dries in 24 hours, this period is required for the glue to completely harden and fix the material on the glass. During this time, it is not recommended to use the laminated glass and turn on the window heating.

| Denial of responsibility | Contacts |RSS