How to cut tulle on a window with a balcony. Tulle from organza

How to cut the curtains: decature and processing of the lower cut. 122 photos of the correct cut of curtains

Sewing lovers often have to deal with problems related to the choice and calculation of the material, the preparation of patterns and drawings, as well as with the assembly and sewing of fragments of the product among themselves. Exactly cut off the edge of the fabric is one of the most difficult tasks even for experienced needlewomen. Especially if it concerns thin tissues, such as organza, veil, silk, chiffon, etc.D. It is necessary to cut thin fabrics when sewing curtains, bedding and decorative sewing products. The edges of the curtains are cut to change the interior or to eliminate defects that appeared over time during operation.

In some cases, the edge of the material has to equalize the edge of the sellers on your own relationship. When buying the fabric, carefully ensure that the seller carefully measured the length of the piece you need, especially if the canvas is very long.

What is the difficulty cutting off tulle

Tulle is a very delicate and fragile fabric, so you need to handle it extremely carefully. With improper operation, defects quickly appear on it in the form of vertical or horizontal arrows, puffs and holes. The difficulty of cutting a tuel canvas is that it slides over the surface. If the size of the piece of material is large, it is difficult to fold it in half and connect the edges symmetrically. For this, it is recommended to lay out tulle on a flat hard surface. Too thin fabric is pre.wetted, faded and sucked or pinned to paper. This method almost completely eliminates sliding during cutting.

Attention! Do not try to cut off the fabric by weight. This method will never give even edges.

What is the difficulty cutting off tulle

Tulle is a very delicate and fragile fabric, so you need to handle it extremely carefully. With improper operation, defects quickly appear on it in the form of vertical or horizontal arrows, puffs and holes.

The difficulty of cutting a tuel canvas is that it slides over the surface. If the size of the piece of material is large, it is difficult to fold it in half and connect the edges symmetrically. For this, it is recommended to lay out tulle on a flat hard surface. Too thin fabric is pre.wetted, faded and sucked or pinned to paper. This method almost completely eliminates sliding during cutting.

Attention! Do not try to cut off the fabric by weight. This method will never give even edges.

Common methods with which you can cut off the tulle evenly:

By pulling out a transverse thread. Instructions

  • Put the desired length on the fabric and mark with a small or pencil.
  • We make a neat incision on the edge of the material.
  • Pull out the thread from the edge, which goes along the duck.
  • On the formed path with scissors or stationery knife, cut the canvas.
  • We get a perfectly even cut tulle.

This method is considered the most reliable and simple. If you use a clerical knife to work, make sure that it is sharp, otherwise you can ruin the fabric. It is necessary to take measurements on a flat surface, gently spreading and smoothing the material on it. A regular table or bedside table is suitable for this. If the size of the fabric is not completely placed on the table, put it on the floor. When cutting, the material should be motionless.

Attention! Do not forget to count on a bed for a curtain tape and firmware of the lower edge.

With the help of fabric cuts. Instructions

  • We lay down the canvas, combine the edges. On the lower edge you can immediately see the size of the skew.
  • Cut the place where the edges diverge. The label should be on both sides of the material.
  • Fold again in half, thoroughly smoothing and align the fabric. Combine the edges with an excess, make a section on it in the same place where there are already marks on the edges. All three cuts should be symmetrical.
  • We unfold the fabric back, while trying not to move it out of place. Now she is again folded in two layers. The ruler connect the marks on the edges tagged on the bend and draw a fishing line for a trimmer with a small or pencil.
  • Gently cut off the material with scissors, we get even edges.

In such a simple way you can adjust both edges of the canvas.

If the curtain does not fit the length for your window, set the required length on the canvas, draw a continuous fishing line for a trimmer. Bend an extra piece along the line and equal the edges on both sides. If the edges coincide with each other, you can cut tulle.

How the tulle is filed? Description of ways

It is not difficult to catch tulle at home. You need a little patience, accuracy and have a simple set of tools in the house: threads, needles, scissors.

To make the curtains from tulle, organza and other thin tissues, take the threads 0 and thinner.

We pay attention, tulle needs thin threads, 0 or less size. The color of the threads and fabric should merge. Remember, first you need to process the side sides of the canvas, then proceed to the lower edge.

If the fabric is translucent, the color of the threads can be selected slightly lighter than the fabric, so they will be less noticeable in the lumen.

The lower part of the canvas is processed in several ways.

The easiest way is to double. In the same method, we processed side seams, but its width in this case is more significant, at least two centimeters.

You can pick up tulle on the sides in several ways. Most often, the advantage is given to the traditional type of processing.

The bottom of the canvas is often treated with a seam. The edge of the canvas is tied to one centimeter, iron. We perform a line at a distance of two or three millimeters from the edge of the bend. Excess fabric is subject to rubbing. We tut up the material again, weaned and stuck, we must try to let the line exactly along the first seam.

Tuck 0.5 cm. Irentify. The usual line is removed 0.2 cm from the edge.

Excess fabric is cut 0.2 cm from the exploded edge.

Twul is being tucking one more time.Willing it again. Distracted at a distance of about 2 mm from the first stitching.

This method can save the amount of material on the gateway.

Often the lower cut is treated with a oblique fiber. this is a trim of the lower cut with a special tape.

We lay the curtain cut on a slanting base, which we then bend. The unprocessed seam remains inside the finishing tape, which we let under the foot of the sewing machine. The line passes along the edges of the tape. The tape can be purchased in a store or make it independently from improvised material.

It is best to add a box with a special foot or foot-wrap.

Tulle with a weighting agent, methods of baking and processing

To give easy material, weighting are used. They are produced in the form of cords or plates. They give the air product a complete look, set its shape.

If the fabric is equipped with a weighting agent, there are difficulties with the adjustment of the length.

There are two options for solving the issue: cut the material on top or rearrange the weighting agent. Basically, housewives choose the first option, because it is difficult to rearrange the weighting agent, or rather it is difficult to make a seam that sews a weighting agent. Not every mistress can repeat such a seam.

What to do if the material is wide, and it is necessary to remove part of the width? It will be necessary to shorten the weighting agent. We shift the mark, exposing part of the tip of the weighting agent, cut off the excess part. After manipulations, we move the mark to the same place. If the pattern allows on the fabric, the intervention is performed only on one side, otherwise the similar actions must be repeated on the other side of the material.

If the tulle has a special weighting sensor or decorative processing that you want to save, then heminate the curtain only on the sides.

How many meters tulle do you need on the window of three meters?

Often the housewives are concerned about this question. The popularity of the dilemma is easy to explain. such a width is the most common and is considered standard. In this case, the width can be different: from 4.5 m to 9m. Naturally, in the first case, the material will lie with a small uniform wave, in the second. chic, lush phalda.

Important! The window width measured not by frame or opening, but by the length of the cornice. At the same time, decorative elements are not taken into account, such as knobs on the sides of the bar.

On the cornice, it is necessary to measure exactly the part on which the hooks will walk. the working length of the cornice

As a rule, if the cornice is 3 meters, then how much you need to take tulle depends on the chosen type of assembly. If the length of the rod is 3 meters, then the calculation is made according to the same formula that is given above. First you need to decide on which braid will be used. Accordingly, then CS: GO, which will be needed to calculate the width of the material for sewing curtains.

So, find out how much tulle is needed for a 3 meter window. Suppose braid is chosen with large gorgeous folds, k = 2.5.

3 m x 2.5 (CS: GO) = 7.5 m 6 cm (allowances for lateral subhyndies) = 7.56 m.

That is, for a window of three meters for gorgeous folds, you will need 7 meters 56 cm tulle.

It is also necessary to take into account the frequency of folds, because they can be located with different steps

Calculation of tulle by cornice: degree of filling

To calculate the material by the length of the cornice, you need to know what such a filling. This is one of the most important criteria in the calculation. It depends on him how magnificent the curtains will look in the end. Filling can be three types:

    Small. The minimum acceptable level. Designers recommend typing material no less than 1: 1.5. That is, with a window width of 3 m, the minimum amount of fabric for sewing is 3 m x 1.5 = 4.5 m. If you take a smaller amount of organza or veil, then the appearance of the product will be more than modest.

There are several more nuances that can affect the calculations:

    Density. The denser the material, the less filling should be. Otherwise, little light will fall into the room. And, conversely, the thinner and more transparent the texture, the more content you need to choose.

Tulle is so dense that it can greatly delay sunlight

A large drawing on Tulle itself looks beautiful, you do not need to hide it in folds

Common methods with which you can cut off the tulle evenly:

By pulling out a transverse thread. Instructions

  • Put the desired length on the fabric and mark with a small or pencil.
  • We make a neat incision on the edge of the material.
  • Pull out the thread from the edge, which goes along the duck.
  • On the formed path with scissors or stationery knife, cut the canvas.
  • We get a perfectly even cut tulle.

This method is considered the most reliable and simple. If you use a clerical knife to work, make sure that it is sharp, otherwise you can ruin the fabric. It is necessary to take measurements on a flat surface, gently spreading and smoothing the material on it. A regular table or bedside table is suitable for this. If the size of the fabric is not completely placed on the table, put it on the floor. When cutting, the material should be motionless.

Attention! Do not forget to count on a bed for a curtain tape and firmware of the lower edge.

tulle, window, organza

With the help of fabric cuts. Instructions

In such a simple way you can adjust both edges of the canvas.

If the curtain does not fit the length for your window, set the required length on the canvas, draw a continuous fishing line for a trimmer. Bend an extra piece along the line and equal the edges on both sides. If the edges coincide with each other, you can cut tulle.

You decided to sew curtains with your own hands, but do not know how to cut off the tulle, curtains, a porter or curtains exactly? It doesn’t matter how you call them, I will take a common name. curtains and you got right at the address, because I will write how to do it correctly. I already have an article where I wrote about this in a brief form: how to pick up a curtain and sew a curtain tape. Now I will describe this moment in more detail.

It’s good if you bought a curtain in the store for only one window and you have already cut it off exactly, although I still advise you to double.check it. Very often “slippery” to the touch of fabric (organza, chiffon, etc.D.) cut off not quite evenly. Sometimes a bevel happens 6-7 cm. If you hang such a curtain on the cornice, then all its unevenness will immediately be visible (see the photo, here the edge is even)

If you still do not know how much you need to buy fabrics for curtains, then read my article and make the right calculation for yourself.

And now the fabric has already been bought and it must be correctly cut into the necessary pieces. I want to say right away that in the production of fabric on the machine there is always the edge of the fabric (this is called the edge) even. In addition, a shared thread always goes along the edge.

To cut off the curtain evenly, I advise you to fold the fabric in half along and carefully combine the edges. If by chance in the store you are not very evenly cut off the fabric, now it’s just that you will see how much the skew.

If the edge is uneven, then in order to leve it you need to cut the edges of the edge with scissors, where the discrepancy begins, t.e make a control mark (cut). Your cut should be on both edges.

Then carefully fold the fabric in half along. Now it turns out that the fabric lies in four layers. Very carefully, open your hands with your hands, combine the middle (overlap) of the fabric and its edge. Make a cut on an excess in the place where there are already cuts on the edges. All three should match.

Again, without raising the entire fabric from the table, put it in half. Using a long ruler, connect the cuts on the edges with a cut in the center and draw a fishing line for a trimmer with a small.

Cut the scissors along this line and your curtain will be even. Also align or check the other edge of the fabric.

Now to measure the desired length of the curtain along the edge (the edges are combined) and make a cut. Do not forget to leave 5. 10 cm on the hem for the curtain tape and the bearing on the bottom.

Fold the fabric in the width in half and carefully combine all four edges. Smoothing the fabric with your hands so that there are no creases anywhere.

Cut the fabric without turning the fabric on the bend with scissors (see the photo). One curtain is cut off exactly.

Thus cut the entire fabric into the necessary pieces. When cutting the curtains, always put off the desired length and level along the edge, then your curtains will always be even and the desired length.

Another way that is well suited for slippery fabrics that are difficult to lay out smoothly. Measure the desired length and make a cut from which you can pull the thread. A strip from the pulled thread will remain on the fabric. So it should be cut on it.

How to bear the tulle correctly: step.by.step instructions

Not always ready.made curtains correspond to the length you need, and sometimes there is a desire or the need to sew curtains independently from your favorite fabric. How to pick up the tulle correctly, process the edges and top so that the curtains look beautiful and elegant?

There is nothing complicated in such works. To bear the curtains, you will need a sewing machine, a minimum set of tools and materials: threads, needles, scissors. Also in the process, keep the iron at hand. you will have to smooth the gateway and seams after each line.

Textile

Often, tulle is called not only the fabric itself, but all the light transparent curtains. They can be made from tulle and other materials. most often it is organza, less often viscose and cotton.

Before you start working with a mild synthetic fabric (tulle, organza), carefully examine the canvas and determine how the shared thread goes. Cut the canvas along it. Before trimming the edges, they must be steamed with an iron.

If your material is a tulle, then it is easier to navigate, you can stretch one thread from the fabric at a distance of 0.5-1 cm from the edge, and then cut off along the resulting line. With the other fabric, such Focus will not pass. you will have to trim without a guideline.

Synthetic tulle is very slippery, so each edge is aligned one at a time. It is desirable to put dense cotton fabric under the material so that it slides less.

Threads and needles

Thin threads 0 or less are selected for tulle and organza. Their color should be in harmony with the color of the fabric. If the material shimmers, then take the threads a couple of tones lighter. light on a dark background does not stand out.

Thin needles are inserted into the machine. They should be sharp, since tulle is very delicate material, it is easily tightened and torn.

very easy princess tulle skirt // cutting and sewing ����

Preparatory work

Before work, cover the table with cotton cloth. this will reduce the sliding of the curtains on the surface.

Very thin material is recommended to be picked up on cigarette paper. After the line is performed, the paper simply breaks off.

Before you start working on a sewing machine, sew a little on a small unnecessary segment of tulle. If necessary, adjust the length of the line and thread tension. The seams are made by a straight line with an average step length (3-4 mm).

The lateral edges

First we process the side edges of the curtains.

  • The edge must be evenly cut and ironed.
  • Put the tulle by the wrong side up, wraps a hem of 1-2 cm. We invite an iron.
  • Then we cut the edge once again by 1-2 cm and iron. Thus we get a double hem.
  • So that the material slides less, you can fix it with pins before ironing.
  • We sew the seam on a typewriter at a distance of about 1-2 mm from the edge of the slope.

In the same way, we process the second side edge of the curtain.

How to heal in length?

Some curtains have a beautiful finish below. lace, festoons, original pattern. Sometimes weighting agents are inserted into the tulle. a special cord or weight. In this case, adjustment of the length of the curtain is carried out only when processing the upper edge.

If the bottom of the canvas is simple, then it can be bent in several ways. The easiest is a double hem, the same as on the sides of the canvas.

The width of the bent is slightly larger than on the sides, and the curtains depends on the material.

  • In hard tissues (kapron, organza), the width of the gate should be at least 3 cm.
  • Veil and light tulle can be touched by 2 cm.
  • Plastic grids are recommended to be lined with a width of 1 cm.

complex performed are seam (American) or slanting.

the seam

How to pick up tulle from organza? A good way is the so.called seam.

  • The edges of the curtains are touched by 0.5-1 cm, weaned.
  • Perform a straight line at a distance of 2-3 mm from the edge of the slope.
  • The excess gate fabric is cut at a distance of 2-3 mm from the line. The material should not crumble.
  • Once again touched the fabric, ironed and struck. Try to get into the first line or perform a seam at a distance of 1-2 mm from it. In this case, the first seam remains inside the bend.

In this way, a light, air edge of the curtains with a minimum consumption of material on the gap is obtained.

Spitter

This method is most often used to process fabric with embroidery or tulle-nets.

For him you will need a special paw that comes with a sewing machine. It can also be purchased in sewing stores. A foothill paw is also suitable. The bottom of the curtains is evenly trimmed, ironed and reduced when performing the line (the edge of the canvas is seasoned in the foot).

I scoop the box can be purchased at the store. This is an applied tape with pre.adjusted allowances, it can perform a decorative function (for example, atlas boxes). Sewing it is simple.

Processing of the upper edge

Lastly, the curtains begin to process the upper edge. Most often use a curtain tape. it is convenient and beautiful. With the help of a curtain tape, or extrafora, you can get various folds and drapery of the canvas.

  • Measure the desired length of the curtain. For practicality, it is recommended to make it 10-15 cm less than the distance from the floor to the cornice, but some prefer curtains “in the floor”.
  • A allowance of 2-2.5 cm is left to the required length.
  • The curtain ribbon is purchased at the rate of the width of the curtain plus 5 cm on the side slopes for each curtain.
  • The tulle is placed the wrong side up and touched by 2-2.5 cm, ironed.
  • A curtain tape is applied to the gateway. The laces and loops of the tape should be located outside.
  • The tape is pinned with pins and stained at a distance of 1-2 mm from the upper edge of the curtain.
  • Having reached the edge, the laces are freed, and the allowance of the tape is tilted inside 2-2.5 cm on each side.
  • Perform the second line along the lower edge of the tape, also retreating 1-2 mm.

The curtain is ironed and pulled together with the tape to the desired configuration of folds.

That’s all, Tulle is ready to take his place on the window and delight you with his beauty.

How to properly pick up a tulle using a tape with your own hands

You bought a finished fabric, but the model has a length that is absolutely not suitable for the size of your window? “How to bear the tulle correctly?”. this is the first question that every housewife who bought a ready.made curtain asks himself.

Creating comfort in the house, the curtains are given an important role, and this is no coincidence. After all, the lack of curtains make the windows “stripped”, and in some cases even flawed. Such a room looks empty, even if it is equipped with furniture, equipment and exclusive decor elements.

In order to satisfy the needs and desires of each buyer as much as possible, manufacturers produce wide canvases. The probability is large that such a width is suitable for windows of any height. After all, from practice it is clear that long into short can be turned easily, but on the contrary. it is unlikely that.

Hostians of apartments with low ceilings are faced with a problem when they purchase a ready.made tulle. it is necessary to pick it up to give the curtain the necessary sizes. Some carefully turn to the masters-specialists in the studio, while others seek to independently solve the problem.

In addition, it is not at all difficult to do.

You decided to pick up the tulle? How to pick up tulle from organza and do it right? The technical side of your actions should be perfect. Tulle is a delicate and elegant fabric that requires the same relationship: delicate and cautious. So, let’s begin!

We carefully study the fabric

If you do not want to spoil the curtain, we suggest not neglect the next recommendations.

  • Consider the fabric canvas and determine where the shared thread is located.
  • Cut the fabric is desirable (but not necessarily) along the shared thread. Cutting a fabric with violation of this rule, you can get a very interesting final result. But you should not risk. Rely on the knowledge of specialists, and then your tulle will acquire an attractive appearance. If the curtain is very thin, consider the ability to cut it not along, but across the shared thread.

Choosing threads and needles

  • Choose needles. And this step is absolutely independent of whether you plan to seek help from specialists or decided to pick up the tulle yourself. The main thing is to choose the most suitable needle. Beautiful and even stitches by 50% depend on the quality of the needle. Tulle is a delicate, light, air fabric, and therefore the needle should be appropriate. thin.

So that the tulle does not slip, spread cotton fabric on the desktop (can be fixed with masking tape)

We prepare the workplace

Before you start cutting, click the table with a natural cotton cloth (it is advisable to fold it with several layers). You know that tulle is a very thin fabric, the fibers of which are very mobile. And the cotton fabric will ensure the static of the tulle on the table, reducing the degree of sliding of the thin material, and will take care of the smooth edges.

Preparatory work is completed, and now you can safely move on to the main goal. to pick up the tulle.

Smooth the tulle

Before the main decisive actions, it is recommended to smooth the edges of the fabric, very often they look jerking.

It’s good when, when buying a tulle, it was cut off exactly, and if not? If the fabric was torn off, then its edges are uneven. They must be leveled before healing. Sometimes the cut edges also have bumps. be careful! Before sewing, the edges of the fabric should have clear even edges. How to achieve this?

First, verify the edges. After the situation will clear up. You will see what your canvas has. even or not very.

Organza will have to cut along the ruler, because pulling out a thread for a guideline from such a delicate fabric will not work

Determine the landmark

If it is required to pick up the tulle on the sides, it is necessary to retreat from the edge a distance equal to 3-4 cm, and only then hook one thread with a needle.

Then very carefully (so that the thread does not break) stretch it along the canvas in the direction from top to bottom. If the operation was successful, then you will get a flat fishing line for a trimmer.

It is she who will be the so.called landmark. Stick tulle along the line, turning it twice.

Then, when an organza is used as a tulle, it will not be possible to stretch the thread simply. Organza fibers are so thin and fragile that they will crumble in a moment without having time to break. The edges of the organza must simply be cut evenly.

We process the side sides of the curtains. We put the tulle up the wrong side and begin to iron the sides at a distance of 1.5-2 cm. Make sure that the cut is inside. It is better to fix the resulting design with invisibles.

We insure the sides

At a distance of 1-2 mm from the internal bend, we arrange the sides, using the threads, the color of which is identical to the color of the curtains. When both sides are built up, the fabric should be laid upward, putting a curtain tape on it, located similarly. The unprocessed upper edge is connected to the tape so that the tulle is under the tape over its entire width.

Next, the strips of the tape bend inward by 2 cm, pinching them to the fabric with pins. The curtain tape is attached (1 mm from the edge). It is important that the threads are white. We take out the pins and bend the tape back, now it is from the wrong side. We fix it again. Now we use colored threads. We free the threads on the tape, adding the tape from the side edge.

We determine the desired length

In order for the result to be positive, it is important to correctly determine the length of the tulle, which in the ambulance will decorate your windows, creating a unique atmosphere of comfort, warmth and comfort in the house.

When the side sides are already leveled, it is important correctly, given the allowances, to give Tulle the necessary length. If you need to bear the bottom of the tulle, the actions are similar. It should be measured from the bottom of the fabric of 14 cm and stretch the thread. Having done this, you will see a flat fishing line for a trimmer located along the length of the entire edge.

  • Measure the length. If you are guided by the basic rules, it is important to know that the curtain should have a length that is shorter than a common dina from the cornice and to the floor by 10-15 centimeters. A curtain of this length easily opens and does not collect dust from the floor.
  • Make markings (soap, pencil or chalk) on the fabric surface.
  • Cut the remains of the canvas.

Methods of repairing tulle

Each tuel curtain is unique. Veil, organza, chiffon, mesh. any fabric has its own structure, monotony, pattern. The question of how to sew tulle should be approached taking into account the characteristics of the curtain.

We apply the web with glue to the wrong side of the part and simply iron the paper of the web from above

Then we exfract the paper from the glued cobweb

We apply a decorative part that we want to glue on top, the front side of the fabric is obtained from above, and iron

Sometimes it’s enough just pin or sew a decorative butterfly or feather to it to mask the hole. Before sewing up torn places, show imagination, creativity of thought. So, a hole from a burned cigarette can be decorated with an application from another tulle curtain. This is time.consuming, but if you succeed, your curtain can acquire a completely different look, more beautiful and sophisticated.

Using various embroideries and linings, you can not only decorate the spoiled area, but also decorate the tulle

tulle, window, organza

How to sew tulle after cat claws

One of the most common is the question of how to sew a tulle if a cat broke. Unfortunately, pets often spoil various interior things. Excessive playfulness, sudden fright. and the cat is already hanging on the curtain, clinging to it with claws. Fortunately, there are no torn, shapeless damage on tulle. They are always horizontal or vertical cuts. And this is good, because it is quite easy to sew in a straight line.

    If the cat failed to break the fabric, and the tightening has formed, then it can be repaired by pacing the tape or braid in this place. Most often the tights are vertical, so the braid will have to be sewn along the entire length of the curtain. Sometimes, one sewn tape looks ridiculous, then sew another, symmetrical, or make several lanes. It is quite original if they are contrasting, marked with a bow, brush.

Sew a decorative braid or fringe along the tightening line in the overlay, decorate with a bow, brush or other decor

Cut the horizontally torn piece, grind back, decorate

If the tulle is torn from above or below. we sew another, you can contrast a piece of tulle

Damage by an iron, how to repair tulle imperceptibly

First of all, it is necessary to check the condition of the sole of the iron, it must be cleaned

Unfortunately, the situations when the tulle burned with an iron is not uncommon, and what to do, many housewives simply do not know. Subpalins from the irons are large, voluminous, it is not easy to disguise them, in addition, in this place the curtain loses its original color and acquires an ugly red tint.

Most often, a burned place should be cut by cutting the fabric into two parts. It is best to make a vertical cut, having received two stripes. From them you can make new curtains, for example, on the kitchen window. By showing imagination, you can make multilayer curtains, adding a similar fabric of a different color.

If we broke in the middle, we make a split tulle of two halves, cutting a piece with a marriage

Another way to fix the burned tulle is to sew a fraud. This is a creative case, because you can’t take a palm on the curtains burned with an iron from the first fabric. this will be an extremely unaesthetic solution. The fabric is selected similar in structure and composition.

Correctly selected glue applications will help to quickly decorate tulle without much effort

Ideally, if you have a small supply of this tulle fabric in the form of a wide cut strip or a tired and filed edges of the curtain. Latka is cut out not in the shape of an iron. it is worth approaching this case non.standard. It can be a flower, star, geometric figure.

Embroidery on tulle will look original and appropriate in any room

If your patterns go according to the structure of the fabric, then you can make a fraud within the drawing. Next, it is sewn or glued to a burned place.

How to repair tulle from organza

Organza is thin and transparent, has a strength and even rigidity, which allows you to maintain shape and practically not crush

Organza. thin, transparent and with dense and durable interweaving material. But even this fabric can easily break. If you have a question: the cat broke tulle, how to repair? Much depends on whether the fabric is with the pattern or smooth. If smooth, then you can fix it by cutting into two parts, compiling them in a new design. Today it is very fashionable to make curtains from organza multicolor (two or more color with the same fabric structure).

Combined curtains from translucent material

They are sewn from individual vertical or horizontal stripes, collected by folds, grabbed with magnets or special holders, hooks, clamps.

You can make two.tone curtains of two halves

In the event that tulle from an organza with a pattern was torn, and how to repair it, the rapport of the pattern will tell. In many cases, it is not worth violating the structure of the fabric, since the curtain will lose all its charm and integrity.

The curtain from the organza with the pattern looks original, it needs to be repaired depending on the pattern

You need to see if it is possible to hide a defective place in a fold or disguise it with applique, a decorative element. Sometimes it is worth carefully sewing up the gap with thin threads suitable in color, and hide it from the eyes.

Beautiful applications will certainly decorate the tulle and will not let the fabric collapse

Detailed instructions for baking curtains

If you do not want to trust this responsible business to strangers, learn to pick up the curtains yourself. This skill is certainly useful to you in your life. Now you will learn how to sew a curtain tape. Select a tape of suitable width. The denser the fabric, the wider the tape should be.

In the curtain tape there are loops located in several rows. Even without changing the length of the curtain, you can raise it from the floor by a few centimeters. Let’s rather move from words to business and learn how to pick up curtains with a tape.

Processing of the upper edge

Lastly, the curtains begin to process the upper edge. Most often use a curtain tape. it is convenient and beautiful. With the help of a curtain tape, or extrafora, you can get various folds and drapery of the canvas.

  • Measure the desired length of the curtain. For practicality, it is recommended to make it 10-15 cm less than the distance from the floor to the cornice, but some prefer curtains “in the floor”.
  • A allowance of 2-2.5 cm is left to the required length.
  • The curtain ribbon is purchased at the rate of the width of the curtain plus 5 cm on the side slopes for each curtain.
  • The tulle is placed the wrong side up and touched by 2-2.5 cm, ironed.
  • A curtain tape is applied to the gateway. The laces and loops of the tape should be located outside.
  • The tape is pinned with pins and stained at a distance of 1-2 mm from the upper edge of the curtain.
  • Having reached the edge, the laces are freed, and the allowance of the tape is tilted inside 2-2.5 cm on each side.
  • Perform the second line along the lower edge of the tape, also retreating 1-2 mm.

The curtain is ironed and pulled together with the tape to the desired configuration of folds.

That’s all, Tulle is ready to take his place on the window and delight you with his beauty.

Summing up, let’s say that if you buy ready.made curtains in the store, and do not sew them to order, then you will probably need to fit them along the length. To bear the tulle, just have a sewing machine at home. Of course, you can perform seams manually, but this is too laborious.

Most often, curtains from tulle and organza are sewn in a double.bending method. To save material or not weight a curtain, you can use the so.called seam. And if there is a need for decorative decoration of the lower edge, then you can sew a beautiful braid or use the finished braid base.

A cozy apartment or house cannot be imagined without curtains on the windows. They make comfort, save heat, give beauty and well.groomed appearance to the room, especially if the window structures themselves leave much to be desired. In the choice of material for curtains, the modern homeowner is not limited. You can hang natural, combined or artificial matter. The easiest option is to buy ready.made curtains in a specialized store. Products of standard length and width are sold there. If you need the only and unique curtains on the windows, there is only one option. to select a curtain fabric and pick it yourself. It’s not as difficult as it sounds. How to pick up curtains with a tape? This can be done in three different ways.

Quick & Easy Method for Cutting Tulle. How to Cut Tulle for the Orchid Lane Dress


| Denial of responsibility | Contacts |RSS