How to dilute Stihl oil for two -stroke engines. Husqvarna oils

How much oil is it for a stihl chainsaw

The quality of these operational materials has a decisive effect on the functioning and service life of the chainsaw motor. A two.stroke carburetor engine and two tanks are installed on at least some kind of saw (one for filling the fuel consistency, the other for filling the oil grease). The volume of the fuel tank is from 0.3 to 1 liter, and the volume of oil, usually less than 1.5–2 times. This ratio of volumes leads to the fact that the oil lubrication oil and the fuel mixture are completed approximately immediately, and specifically after 30–45 minutes of operation (at full load).

The need for the manufacture of fuel consistency is understandable to everyone who is familiar with two.stroke engines: the difference between the working cycle of a two.stroke engine from a four.stroke leads to the fact that to lubricate all the rubbing parts (piston, shaft, etc.D.) You can not use the oil pumps and the oil has to be added specifically to gasoline. All this is quite fundamentally, because samples only work on gasoline or violation of the required proportions of gasoline-oil consistency will rapidly lead to a breakdown of the tool.

Tips on brands of gasoline and oil, also on the proportions of the fuel mixture of subsequent. When working with Russian chainsaws, 76th gasoline and ordinary oils for two-stroke engines are used, which are added to the mixture in an amount of about 4%, in other words in a ratio of 1/25. Foreign models require the introduction of gasoline with an octane number of 92 (or higher) and company oil manufacturers of chainsaws (with all this, oil in such a consistency should be about 1/40).

In principle, oil for two.stroke engines can also be used on foreign chainsaws, but, two incidents should be implied. At first, you must be convinced that the gasoline is unsuccessful. 2nd-if the oils are designed for engines with a speed of up to 8.5 thousand per minute, and in the chainsaws of foreign production, the revolutions can reach 11-14 thousand, then the introduction of these oils reduces the tool of the tool by an average of 7-10%. But for STIHL, how much oil is added to gasoline for how much oil to pour in gasoline. There is a game of candles. decide for yourself.

With oil for lubricating the saw apparatus more abundant: in all models of domestic and profiles of chainsaws you can use ordinary Zhigulevsky oils (for example, motor oils are recommended for Husqvarna models, and transmissive oils are recommended for STIHL).

Attention should be directed to the features of the seasonal operation of the tool. If the saw is used at low temperatures, then even with the correct choice of all the ingredients, the quality of oil and fuel consistency may be unsatisfactory (crystallization occurs and viscosity increases significantly)

In this case, the saw itself should be adapted to use in such criteria. for example, it is necessary to predict the possibility of warming the carburetor during operation. In addition, it is recommended to warm up the saw before work (if it was stored in an unheated room)-in order to avoid unnecessary consequences due to the presence of condensate.

How to choose?

Each chainsaw has a two.stroke carburetor engine and two tanks: one is filled with gasoline, in the second. oil. When choosing a composition for lubrication, zoning plays an important role. It should be minimal. Another important indicator is resistance to low temperatures: the oil should not freeze under a strong minus, which will ensure the quality of the entire tool.

For lubrication, it is recommended to use adhesive oil for chain chains containing special substances, thanks to which the composition is well gripped with a chain. High.quality oil will remain on the chain when it rotates, and the chain itself will be more reliable in operation.

Another important indicator of lubrication is the density: if the composition is liquid, it will be consumed in large quantities

In order to avoid harm to the environment when using a chainsaw, it is important to use vegetable oil. His waste will decompose in a natural environment

What oil for chain chainsaws to choose, because modern manufacturers offer a wide range of options? Of specialized manufacturers, you can mention brands such as Divinol, Bio-Kettenol, Ravenol, Vegoil, Mobile, Castrol, Shell. Let’s look at the features of their products in more detail.

dilute, stihl, stroke, engines

Correct ratios and cooking for popular manufacturers

Different manufacturers recommend different proportions for their chainsaws

Their observance is followed with attention. The lack of lubrication leads to the failure of the internal combustion engine

An excess. to the loss of power, smoke, the formation of soot with all the above problems.

How to dilute for StiHL, in particular for the MS 180 model

The manufacturer recommends for motors of its chainsaws, including the STIHL 180 ms HP Ultra oil in a proportion of 1:50. It provides the highest capacity, service life and cleanliness of the ICE. It is also recommended to use motor oils in cans with the inscription STIHL

It is important to purchase original, but not counterfeit products here

In the case of a mix of oil and gasoline, not so. The mixture can be stored up to 2 years. After long storage, the container must be shaken to mix the possible precipitate.

Motomix is ​​a ready.made fuel mixture from Stihl, very comfortable when there is no time or the opportunity to mix liquids in place

How to dilute for a Husqvarna saw

The manufacturer in the operating instructions recommends using special oil for Husqvarna. It is adapted to the engines of this manufacturer, provides a long service life and quality work. Poured in a ratio of 1:50.

It is allowed to use oils for two.stroke air.cooled ICE from other manufacturers. If a proportion is not indicated on the canister, the manufacturer of the chainsaw of Husqvarna recommends pouring an increased dose in the proportion of 1:33.

Thus, for 1 liter of gasoline for the chainsaw, Husqvarna is flooded:

  • 20 ml (in the colloquiality of grams) Husqvarna oil (1:50).
  • 20 ml of other acceptable oil, if 1:50 is indicated on the canister.
  • 30 ml per 1 liter of gasoline, 1:33, if another proportion is not indicated.

Husqvarna does not recommend storing the cooked mixture longer than 30 days. Before pouring a defended mixture, it is necessary to shake.

The ratio of oil and gasoline for Partner chainsaws, in particular Partner 350

For its saws, including model 350, Partner recommends using Talon branded oil in 1:40, that is, 1 part for 40 parts of gasoline.

In order to calculate the need for 1 liter (1000 ml), 1000 should be divided into 40. Result. 25 ml per 1 liter (1000 ml) of gasoline.

In the instructions of this manufacturer there is no information about the permissible replacement of the recommended Talon oil with others. In practice, oils for two.stroke engines with air cooling and other brands are used. In this case, the proportions are recommended already by oil manufacturers and are indicated on the canister.

Pay attention to the canister, the inscription 1:40, this once again confirms that each oil has its own recommended mixing proportions with gasoline

How to breed gasoline with oil huter

The manufacturer Huter does not release any one brand for his chainsaws for his chainsaw. There are recommendations for a general type. JASO FC classification oil or others: API TV, API TS, JASO FB for two.stroke ICE of air cooling.

In the operating instructions, Huter himself does not call proportions, but indicates that the mixture is compiled in the proportion indicated by the manufacturer of the oil.

For example, if the canister indicates 1:50. 20 ml per 1 liter of gasoline is poured. If indicated 1:40. 25 ml per 1 liter.

How much oil per liter of gasoline is poured into champion chainsaws

For its chainsaws, Champion recommends using Champion oil for two.stroke high.speed air.cooled ICE. Proportion 1:50, that is, for 1 liter of gasoline 20 ml.

In addition to the CHAMPION proprietary, the use of oils for the same engines of other brands is allowed. over, it must comply with the standards of the API TV/C or JASO FC/D, which should be indicated on the label of the canister.

How many grams of oil per 1 liter of gasoline are needed for makita saws

Makita, recommends for its gasoline saws, Makita oil for high.performance two.stroke engines

Makita pays attention to environmental protection. Oils of this brand have a minimum of polluting exhaust

Recommended proportions 1:50, 1 liter is poured 20 ml. It is allowed to replace with analogues of other brands, provided that they meet the international standard TS-3. At the same time, it is recommended to add more oil in the instructions, 1:40, for 1 liter 25 ml.

Advantages of branded oils

Many domestic and foreign manufacturers specialize in the production of special motor oils, but the highest rating indicators in STIHL, Husqvarna and Makita branded products.

dilute, stihl, stroke, engines

Only in separate parameters are the company’s proprietary motor oils of the LUKOIL trademark.

In the list of advantages of branded engine oils:

  • economical consumption;
  • the stability of the working characteristics in difficult operating conditions and with long.term storage;
  • the minimum amount of toxic compounds in exhaust gases;
  • almost complete absence of soot.

According to the American classification, to work in household and professional models, you can use API-TB category oils. Japanese analogue-JASO-FB and JASO FD. The preparation of a combustible mixture using oil for 4-stroke engines is categorically excluded.

Red, green or any other oil color determines the product belonging to the assortment of a particular manufacturer, therefore, when determining the characteristics of the material, it is not taken into account

Extremely carefully approached the choice of motor oil of an unknown composition and origin

Before receiving additional information about quality and operational parameters, it is better to temporarily refuse to use such material.

It is allowed to mix the same type in composition and purpose of motor oils produced by the quality of their assortment of brands. Under no circumstances, mixing oils of mineral and synthetic.

The choice of oil

Unlike four.stroke engines, STIHL 180 chainsaw oil is poured directly into the gas tank, having previously mixed with gasoline. It is recommended to pour the oil specified in the instructions for this model in the chainsaw.

In no case can you use oil intended for low.speed engines (boats, scooters, etc. D.).

It can significantly reduce the life of the motor, and if traces of such a substance in the cylinder-piston group are detected, the tool will be considered removed from the guarantee, t. e. will not be subject to warranty repair or exchange.

Synthetic and mineral oil oils for chainsaws STIHL are sold in bottles or cans of different containers: from 100 ml to 5 liters. Minerals have a lower cost, and semi.synthetic and synthetic provide complete combustion in the process of engine operation, t. e. lack of soot and a minimum of toxic compounds in the exhaust.

In addition, synthetic oils retain their qualities in a much wider temperature range, as well as contain special additives that are useful for engine operation: anti.orally, detergents, cannibal, etc. D.

You can choose motor oil for your tasks depending on the model of the saw and the frequency of its use: the oil consumption during the operation of the device is low, and given the shelf life of semi.synthetic and mineral lubricants, there is a risk of simply not having time to use even a liter bottle to the end.

So with small alleged volumes of work, you can not buy a voluminous canister, but limit yourself to a bottle. The expiration date does not have only mineral lubricants of Stihl.

Let’s talk about the installation of oil supply directly to the chain

First of all, I would like to put Accent on the fact that all the STIHL manufacturer’s chainsaws have quite small sizes, but, nevertheless, they are very powerful. It is these features that attract potential buyers of this kind of technology to the models of this company. over, you can easily produce various kinds of manipulations with this device regarding work with wood (see. how to cut down a tree).

Device for supplying oil to the circuit

In addition, Stihl chainsaws have a high level of cutting ability. over, this technique is equipped with the latest accessories (see.Nazadka for the chainsaw angular grinding) is additional due to which they contribute to convenience and ease of work. But actually let’s talk directly about the device itself, which the manufacturer has equipped with his chainsaws. So, the system of direct chain lubrication of the Stihl chainsaw consists of:

It is worth noting that the direct oil feed through the operation of the pump has a special adjustment. An important fact is that the chain is lubricated throughout the work of the chainsaw. It is for this reason that this part serves its owner for a rather long time.

During the operation of the device from the groove groove, the oil begins to exit directly and is immediately absorbed by sawdust.

That is why the process of lubrication of the chain area is carried out automatically. But it is worth noting that there are models that have the so.called “dosage” of oil, which should be supplied directly to the chain. And naturally models, the price category of which is quite low, are located only by a manual pump directly through the impact of the drive, which is located on the handle.

Correct proportions

Most often, when preparing fuel for the work of saw, 1:50 and 1:40 are used to work. This means that one part of the oil is added to 50 or 40 parts of gasoline. Calculations are made as follows: 1 l = 1000 ml, 1000/50 = 20 ml or 1000/40 = 25 ml, that is, in the first case, pour 20 ml into each liter of gasoline, and in the second. 25 ml of oil. If there is no instructions and you do not know the proportion to prepare the mixture, then use the following recommendations:

  • Tool and oil of one brand. For example, for the Stihl chainsaw, the ratio of gasoline and STIHL oil will be the same as indicated on the container with oil, usually 1:50.
  • The substances used for the mixture have different brands. the proportion of 1:40 is selected.
  • There is one brand, but there is no information about the ratio of substances on the oil. they are divorced 1:40.
  • In the absence of any data on the saw and oil, the mixture is bred in a proportion of 1:40. The only thing you need to make sure that the oil is intended for two.stroke engines.

To carry out the run.in a new saw at the first three gas stations with fuel oil, add 20% more. In this case, instead of a ratio of 1:50, it will be 1:42, and the proportion 1:40 turns at 1:33. 24 or 33 ml of oil, respectively, will require a liter of gasoline. Other countless events with a new saw do not conduct. Manufacturers advise working only at the largest speeds always. After the instrument run, the usual proportions are used 1:50 or 1:40. In some cases, the manufacturer of the equipment also indicates other ratios, for example, 1:25 or 1:32, they must be observed.

The principle of lubrication of the chain and tire

The main block of the system is the pump. The principle of its work is as follows. Когда частота вращения двигателя увеличивается, шестерня, установленная на главном валу, приводит вал насоса через червячную шестерню. In turn, the rotation of the shaft creates a certain pressure in the oil line, which makes the oil move along it towards the bus.

  • oil tank (located in the crankcase, oil needs to be poured into it so that it comes to the chain);
  • oil filter (installed inside the tank);
  • oil pipeline or oil.conducting hose (made of rubber resistant to wear);
  • oil pump;
  • gear of worm gear;
  • The tire of the chainsaw (it contains holes through which oil comes).

The oil channel ends where the chainsaw crankcase is in contact with the tire. There is a longitudinal groove in this site. When the tire is installed on the chainsaw, the oil channel coincides with this groove. The groove regulates the flow of oil to the tire of the chainsaw, and its number is in no way related to the degree of tension of the chain.

After the oil enters the tire, the chain is involved. it usually has holes from which the oil falls on the entire plane of the tire. The higher the number of roller roller speeds, the more oil will enter the circuit. Some models of chainsaws have special adjusting oil pumps, with which you can adjust the amount of oil entering the chain. This is how the degree of lubricant consumption is adjusted.

What oil to choose

If you are an ordinary user of the chainsaw and do not use it daily for 6-8 hours, while you only work in the summer, then you can use the usual Stihl HP to prepare fuel mixture for your chainsaw. The optimal ratio of the price and quality of lubrication made it popular among millions of users of benzo.tool.

STIHL HP can be used to prepare a mixture for any two.stroke engine, including moped engines and boat options.

The advantages of branded motor oils are super and ultra

Branded lubricants do not need any additives and additional components. It should be borne in mind that fuel mixtures prepared with the use of mineral oils, and their synthetic analogues, it is forbidden to mix.

Oil for two.stroke stihl engines

Stile has three grades of oil for two.stroke engines:

It is not difficult to guess the simplest, most affordable and common is Stihl HP, followed with improved characteristics is the STIHL HP Super oil, and the Stihl HP Super closes the line.

Oil for two.stroke engines STIHL HP

This oil (additive) can be used not only in chainsaws, but also wherever a two.stroke engine with air cooling is installed. This is mainly garden technique: trimmers for grass, combi systems, gas troops, etc. Application in scooters or boat engines is possible if it allows the instructions for the device. It can be distinguished by a characteristic red color.

STIHL HP is designed on a mineral basis and designed specifically for the STIHL technique, paired with which it allows you to use the engine resource as efficiently as possible, not losing power protecting the engine elements from the consequences of friction, high loads and temperatures. Belongs to the JASO FB class, that is, complies with standards, but on the lower border of tolerances.

This classification is adopted and licensed in Japan. This name is from the abbreviation Japanese Automobile Standarts Organization. We are interested in the classification of oils for two strokes.Standards for them begin with the letter f. Jaso Fa.Oil for use in developing countries. JASO FB. corresponds to the minimum conditions that allows its use in Japan. JASO FC. Oil suitable for the main parameters for use in Japan. JASO FD.This is the oil of the highest category with maximum tolerances.

The most common butter from Stil that can be found in almost any specialized store, and not in specialized ones, too.

STIHL HP oil is spilled in capacity with volume:

Oil for two.stroke engines STIHL HP Super

This green oil refers to JASO FD, but its lubricating properties will be higher than that of StiHL HP. In addition, it leaves less than a carrier on the cylinder, pistons and in the muffler. In environmental friendliness, it is again higher than HP without Super console. However, it is worth noting that the price of such oil is noticeably higher than the above. HP Super is better to use if the chainsaw is used intensively, and not for infrequent work.

STIHL HP Super oil is poured in the capacity of the volume:

dilute, stihl, stroke, engines

Oil for two.stroke engines STIHL HP Ultra

Green oil with a slightly lighter shade than HP Super. This is the oil of the highest category from the entire line of Stiel. It can be used both with two-stroke engines and STIHL engines using 4-Mix technology. Belongs to the JASO FB class. Highly ecological, practically does not leave a carbon fiber, does not form soot, does not coke and quickly decomposes when it enters the soil. The only minus of this oil is a very high price.

Ready.made fuel mixture Stihl Motomix

What progress has come to And really until the most not to eat miracles! Already ready.made mixtures of oil with gasoline are sold. True, it is difficult to find such a mixture even in the dealer to put it mildly, but the fact itself! Many readers will be surprised- “Why sell what you can do on your own?””. Buy oil, buy gasoline and mix yourself. It seems that everything is so, at first glance, but gasoline will be ours, with our same quality and oil will be at best HP, not HP Ultra. And in Motomix mixed from Stile and gasoline not even European, but with improved indicators and HP Ultra oil and the proportions of those that are needed and extinct to milligrams. This means that such a mixture is most optimal for chainsaws with two-stroke engines and with 4-Mix engines.

ЛИКБЕЗ – 2Т масла для бензопил и мотокос! Всё непросто

And if HP Ultra can be bought, then it is almost impossible to find high.quality gasoline based on alkylates. Namely, it increases the shelf life of the fuel mixture, allocates at least the minimum of sulfur, benzene and other substances.

Here is the table in which the characteristics of the EN 228 Super gasoline are compared (in our opinion it is the 95th, but our 95th to it is like to the moon) and gasoline from the STIHL which is used for this fuel mixture.

Characteristic En 228 Super Motomix
Octane number according to the research method 95 95
Octane number by motor method 85 90
Steam pressure, kPa 45-100 50-65
sulfur, mg/kg 150 ten
aromatic hydrocarbons, about.% 42 0.5
Benzole, about.% one 0.05
Olefinov, about.% eighteen 0.1
Oxidation resistance, min. 360 720
Stability OK. 1/2 years 2 years

There is no doubt that the work on such a fuel mixture will be able to increase the saw resource to the maximum possible, the power will correspond to the passport, and there are enough other pluses. But the price of such a mixture is very high. But if you look in the long run, then this will pay off.

How to breed gasoline for a chainsaw STIHL 180?

Most of the owners drank this model, are wondering which gasoline is to fill in the Stihl 180 chainsaw and what proportions with oil must be observed. The best option is 1/50, which means that for five liters of the finished mixture, you will need only 100 milliliters of oil.

How to mix gasoline with butter

You can extend the operational period of the Stihl MS 180 chainsaw using a high.quality, properly prepared fuel mixture. Quite often for this model, AI-2 or AI-95 gasoline is used. Pay attention to the fact that exclusively non.ethyl gasoline is allowed, which is able to protect the engine from premature breakdowns.

Option of alternative fuel

For refueling household and professional chainsaws, it is recommended to use non-alcohol components and additional additives-car gasoline type AI-92. The question of whether it is possible to pour 95 gasoline into a chainsaw to date remains controversial. Theoretically, the AI-95 gasoline is higher than that of the standard AI-92 fuel, but in practice it is better to give preference to the second option. The problem is that in order to increase anti-depth characteristics, additives and sales are introduced by manufacturers and sales, the quality and efficiency of which in specialists causes reasonable doubts. Such fuel does not fully meet the required characteristics, does not have proper stability during long.term storage. After 3-4 months of exposure, its working properties worsen by 25-30%.

The configuration of the device is designed for users with various experience with these equipment. Cleaning, replacement or repair will not be difficult for you, since to disassemble the carburetor on the Stihl chainsaw 180 is quite easy.

You can make the unit yourself, change the gaskets and a needle valve, for which you will need disassembling the Carburetor STIHL 180. To do this, it is necessary to promote four screws located on the lid of the compensator, as well as lead one on the fuel pump. After you open the body of the unit, you should be extremely attentive, since even the hit of small litter and even hairs can make the operation of this unit impossible.

Two Stroke Oil Talk. Why Anything is Better than Ultra for your Chainsaw!

Stihl chainsaw oil

To begin with, it would be nice to mention that all Stihl chainsaws are created with quite small sizes, but with their dimensions, they have a very impressive power. Thanks to this feature, Stihl chainsaws are in great demand.

Despite the high quality, durability of the chainsaw depends on the use of the correct lubricant and fuel. The first problematic question that the owners of this technique face is: what kind of oil and fuel to choose for their chainsaw? In this article you will learn about which oil is better to use for your chainsaw, and about which fuel is better to fill in your “baby”.

Choose oil for chainsaw stihl

The first thing you should know about is that almost all Stihl chainsaws are equipped with a carburetor two.stroke engine. There are also two separate tank in them: the first for oil, and the second for gasoline.

The first, and most importantly, remember that a simple oil is poured in the model of domestic production, which is usually poured into the tanks of motorcycles, and their proportion should be no more than 1 to 25. As for the chainsaws produced abroad, they will need to buy branded oils, the proportion for which is 1 to 40. Of course, you can try to pour oil for domestic saws in an imported saw, in which case, the power of your tool may noticeably fall. The best advice that can be given when buying oil for such a technique is to contact the manual to use your tool.

A good choice will be synthetic oil for two-stroke air cooling engines of the API-TB and API-TC class. Having come to the store, ask the seller about the presence of such brands as Stihl, Husqvarna, Hahotek, Champion, Alco, etc. In no case do not greedy on the ingredients, it is better to spend money on a quality product than then spend a lot of money on repairs.

Choosing gasoline for the chainsaw of Stihl

When choosing gasoline for your chainsaw, you should pay attention to, of course, the quality of the gasoline itself and, its octane number. It is best to take gasoline with octane AI92

You can try AI95, but too many questions arise about its quality. If you doubt the quality of AI95, then AI92 will be the best choice for you.

We do not advise you to use gasoline, which has long been in any container for a long time, whether it be a canister, tank or something else. For the fuel mixture, only fresh gasoline must be used, otherwise, it can lose all its useful qualities: octane number, etc. If you still use not fresh gasoline, then your chainsaw will work at incomplete power. In the case of a rude breakdown, due to the use of such fuel, you will have to spend a lot of money on its repair, since such a case does not apply to warranty, and you will better purchase a new tool.

Making the fuel mixture of gasoline and oil

Before proceeding with the creation of the fuel mixture for the STIHL manufacturer’s chainsaw, pay your attention to the manual from the manufacturer. Why do you need to do this? The thing is that with insufficient oil content in gasoline, the cylinder and the piston will heat up hard, which will occur in the bullying, which will lead to a breakdown of the CPG, and as a result-to expensive repair

In order to prepare a high.quality fuel mixture, you need to mix oil and gasoline in a clearly verified proportion. If the oils are more than necessary, then this can lead to the appearance of soot on pistons and candles. If you overdo it a little with gasoline, then expect the ambulance of your engine. For example, on average, one liter of gasoline should be mixed with 20-50 ml. oils. For a train, it is recommended to pour 4 liters. gasoline. 100 ml. oils. In this ratio, a mixture for chainsaws is prepared up to 1.5 kW. If the power is more than 1.5 kW, 100 ml should be poured. Oils for 5 liters. gasoline. But these are all approximate calculations, always use the proportions indicated in the manual to your saw, if you yourself do not understand how much and what is needed. But do not really believe the numbers indicated on the oil label.

Correct ratios and cooking for popular manufacturers

Different manufacturers recommend different proportions for their chainsaws

Their observance is followed with attention. The lack of lubrication leads to the failure of the internal combustion engine

An excess. to the loss of power, smoke, the formation of soot with all the above problems.

How to dilute for StiHL, in particular for the MS 180 model

The manufacturer recommends for motors of its chainsaws, including the STIHL 180 ms HP Ultra oil in a proportion of 1:50. It provides the highest capacity, service life and cleanliness of the ICE. It is also recommended to use motor oils in cans with the inscription STIHL

It is important to purchase original, but not counterfeit products here

In the case of a mix of oil and gasoline, not so. The mixture can be stored up to 2 years. After long storage, the container must be shaken to mix the possible precipitate.

Motomix is ​​a ready.made fuel mixture from Stihl, very comfortable when there is no time or the opportunity to mix liquids in place

How to dilute for a Husqvarna saw

The manufacturer in the operating instructions recommends using special oil for Husqvarna. It is adapted to the engines of this manufacturer, provides a long service life and quality work. Poured in a ratio of 1:50.

It is allowed to use oils for two.stroke air.cooled ICE from other manufacturers. If a proportion is not indicated on the canister, the manufacturer of the chainsaw of Husqvarna recommends pouring an increased dose in the proportion of 1:33.

Thus, for 1 liter of gasoline for the chainsaw, Husqvarna is flooded:

  • 20 ml (in the colloquiality of grams) Husqvarna oil (1:50).
  • 20 ml of other acceptable oil, if 1:50 is indicated on the canister.
  • 30 ml per 1 liter of gasoline, 1:33, if another proportion is not indicated.

Husqvarna does not recommend storing the cooked mixture longer than 30 days. Before pouring a defended mixture, it is necessary to shake.

The ratio of oil and gasoline for Partner chainsaws, in particular Partner 350

For its saws, including model 350, Partner recommends using Talon branded oil in 1:40, that is, 1 part for 40 parts of gasoline.

In order to calculate the need for 1 liter (1000 ml), 1000 should be divided into 40. Result. 25 ml per 1 liter (1000 ml) of gasoline.

In the instructions of this manufacturer there is no information about the permissible replacement of the recommended Talon oil with others. In practice, oils for two.stroke engines with air cooling and other brands are used. In this case, the proportions are recommended already by oil manufacturers and are indicated on the canister.

Pay attention to the canister, the inscription 1:40, this once again confirms that each oil has its own recommended mixing proportions with gasoline

How to breed gasoline with oil huter

The manufacturer Huter does not release any one brand for his chainsaws for his chainsaw. There are recommendations for a general type. JASO FC classification oil or others: API TV, API TS, JASO FB for two.stroke ICE of air cooling.

In the operating instructions, Huter himself does not call proportions, but indicates that the mixture is compiled in the proportion indicated by the manufacturer of the oil.

For example, if the canister indicates 1:50. 20 ml per 1 liter of gasoline is poured. If indicated 1:40. 25 ml per 1 liter.

How much oil per liter of gasoline is poured into champion chainsaws

For its chainsaws, Champion recommends using Champion oil for two.stroke high.speed air.cooled ICE. Proportion 1:50, that is, for 1 liter of gasoline 20 ml.

In addition to the CHAMPION proprietary, the use of oils for the same engines of other brands is allowed. over, it must comply with the standards of the API TV/C or JASO FC/D, which should be indicated on the label of the canister.

How many grams of oil per 1 liter of gasoline are needed for makita saws

Makita, recommends for its gasoline saws, Makita oil for high.performance two.stroke engines

Makita pays attention to environmental protection. Oils of this brand have a minimum of polluting exhaust

Recommended proportions 1:50, 1 liter is poured 20 ml. It is allowed to replace with analogues of other brands, provided that they meet the international standard TS-3. At the same time, it is recommended to add more oil in the instructions, 1:40, for 1 liter 25 ml.

| Denial of responsibility | Contacts |RSS