How to disassemble a rogue of a trimmer for Champion grass. Specifications

How to install a fishing line for a trimmer coil for a champion grass

The main elements of the trigger is a mowing spike, which is a cylindrical case with a coil inserted inside (bobbin). A fishing line for a trimmer (cord) is refueling into it. The heads differ from each other in the method of supply and refueling of the cord. There are three types of heads in total:

  • Automatic. The fishing line is submitted after that, as the user reduces engine speed. Automatic supply of the cord is very convenient when you need to do a large amount of work. The minus of such a head is a large thread consumption.
  • Semi.automatic. The use of such a head does not require the user to perform any complex manipulations. The principle of its operation is arranged so that the fishing line for a trimmer begins to automatically lengthen at a time when a trimmer for grass works at full speed. It is only necessary to slightly hit the apparatus with the head on the ground (this will remove the locking of the fishing line), and the cord due to centrifugal force will move out of the bobbin. Then the fishing line for the trimmer is cut to the required length with a knife, which is located on a protective casing.
  • Manual. To lengthen the cord, it is necessary to stop the device. After that, the fishing line for the trimmer will need to be pulled manually.

Trimmer coil device for grass

Cassyle heads for trimmers come in different designs. both simple and complex. The figure below shows a semi.automatic trimmer head from the Husqvarna motorcycle (Husqvarna).

This type of head is present in the configuration of most benzocosyles and electrimmers such as Stihl (Stihl), Patriot (Patriot), Champion (Champion), Bosch (Bosch), Huter (Huter) and others. The device of the braid head is quite simple. It includes the following details:

  • the base of the mowing head;
  • button for semi.automatic supply of the cord;
  • Spulk (coil), into which a fishing line for a trimmer is refuel;
  • spring;
  • eyes. through them a fishing line for a trimmer goes outside;
  • trimmer head cover;
  • Trimmer fishing line (cord).

There are also simpler trimmer heads shown in the next photo.

All these nozzles do not allow you to change the length of the fishing line in semi.automatic mode (after pressing the button). In the case of a break in the cord, you have to stop the mower and change it manually.

The fishing line for the trimmer does not extend automatically

If, with a light blow, the trimmer coil button for grass on the ground is not lengthened for a trimmer, then the reasons for this may be the following.

Option 1. there was a snack, t.e. Squeezing the cord between turns. This problem usually appears if the user wound a fishing line for a trimmer to the coil unevenly, with the intersection of the turns, or wound it with insufficient tension. In the latter case, when the mowing head is rotated at large revolutions under the influence of centrifugal force, the cord begins to drag on, as a result of which the interitral clamping of the fishing line is possible. To eliminate the problem, you will have to disassemble the coil on the trimmer and rewind the cord correctly, that is, with even turns with good tension.

Option 2. too short ends protrude from the head. A fishing line for a trimmer may not exit when hitting the ground, if its ends sticking out of the head, insufficient length (short). In this case, the centrifugal force is not enough for the fishing line for the trimmer to stretch. Therefore, it is required to stop the unit (drown out the engine or turn off the ethletric trimmer for grass from the network) and pull the fishing line for the trimmer manually, after pressing the button.

Option 3. a fishing line for a trimmer was soldered inside a mowing head. This leads to the fact that the coil is stopped and does not spin when the button is pressed. Basically, this happens for several reasons: poor quality of the cord, overheating of the coil with prolonged operation of the unit, a fishing line on solid items.

  • In the first case, the cord of third.party manufacturers can be made of low.quality and fusible materials that do not withstand the mechanical and temperature load. Therefore, preference should be given to “branded” fishing.
  • But, if you still purchased a fishing line for a trimmer of unknown quality, and it is often soldered during operation, then you can follow the example of some users who, after refueling the cord, moisten it either with silicone grease (from the spray can) or mineral oil). This procedure greatly reduces the likelihood of soldering a fishing line among themselves.
  • Also, a fishing line for a trimmer can sleep if during a mowing it hit a hard object (stone, fence, dry branch, etc.D.). As a result of this, it is slightly stretched and draws back into the head with high speed. The cord is heated from friction, and its turns are sticking together. The only thing that can be done to eliminate this malfunction is to open a trimmer coil for grass and rewind a fishing line for a trimmer.

Automatic rogues for trimmers how often they break

These are modern coils that have high reliability and efficiency indicators. The principle of their operation is such that the extension of the cord is carried out when the engine speed is reduced in automatic mode. Kosaryu does not need to control the process of feeding the fishing line, as this happens in automatic mode.

Automatic type heads are 2-3 times more expensive than semi-automatic, so not every owner of a trimmer for grass can afford such devices. However, experience confirms that a good and high.quality automatic coil for a trimmer for grass or a lawn mower serves as long and does not break. Among the advantages of automatic heads, it is also necessary to attribute the high speed of the fishing line. To do this, the fishing line for a trimmer is threaded into the holes of the head, and its manual winding on the coil is carried out.

To verify the effectiveness of automatic coils for trimmers will help the test shown in the video below. As experimental “rabbits”, heads of different types are used.

How to replace a fishing line for a trimmer on a trimmer?

Replacing the fishing line of the trimmer for the grass with step.by.step instructions will even allow the owner of the lawn mowed inexpensive in such matters to do a fairly difficult job.

However, before starting work to replace the fishing line on the trimmer, it is necessary to ensure the safety of work

In particular, it should be taken protection measures against careless or spontaneous inclusion of the lawn mower:

  • Exclude spontaneous start,
  • Delete the battery (if used),
  • Place the tool on a comfortable site for work.

It is convenient to perform work on replacing the fishing line for the grass when the lawn mower lies on the table, and the master, who is performed by replacing the fishing line of the trimmer for the grass, has the opportunity to approach the instrument from any side.

Remove the head of the head of the grass for the grass

At the first stage of disassembly, the head of the head of the grass is removed. On the example of the models of trimmers “Black and Decker” and others, it is usually enough to apply some pressure to squeeze the click-fixer, which are on the side of the head of the head of the head of the head of the head of the body to remove the lid to remove the lid.

Some models of lawn mowers initially include dismantling the head of a trimmer for grass, for which a playback key is used, which is included in the tool kit. The head is usually held by two or three screws, access to which is provided through the side holes of the rear decorative cover.

The head cover, where the coil with a fishing line is installed, is usually held due. It is enough for some effort to squeeze the tongue and turn the lid a little, after which the lid is easily removed at the time of squeezing the tongue-fixer, you need to slightly turn and raise the head of the head of the trimmer for the grass to extract the winding drum.

Step two: extracting a winding drum (coil) with a fishing line

The next step in the process is the exhaust drum with a fishing line from the inner region of the head. You need to turn the head with an open side to see a fishing line for a trimmer and a reel. On the side of the head, find two recesses (eyelets) through which the fishing line for the trimmer is bred outside.

You should release a fishing line for a trimmer from the holes by checking the drum. Then gently remove the coil from the head of the head. The winding drum of some models is installed on the spring. This moment must be taken into account by performing the operation to extract.

The procedure for extracting a coil of a trimmer for grass with a fishing line from the inner region of the head: 1. head assembly with a coil; 2. extracting neatly with a small axial turn; 3. extracted details of the old fishing line for a trimmer are completely removed from the coil. To remove the old fishing line for grass, you need to remove the forest from the loops and pull the free end. This method is removed by the whole old winding. A similar process is repeated on the second section of the drum. The master is recommended to use gloves when performing work.

The shape of the handle

Manufacturers offer 2 pens options:

The handle in view of the letters “T” is installed on models with auto.wrapping a fishing line. The work is carried out with 2 hands located on both sides of the bar. This situation is convenient for mowing large areas of vegetation. The cut is carried out according to the principle of braids for grass. from one side to the other. This option is not maneuverability, it works poorly on a complex relief. Bicycle steering can be equipped with control buttons. In household types of a trimmer for grass, the launch buttons are installed on the rod.

The classic model of a trimmer for grass with a bilateral handle on which the control buttons are installed

Disassemble and assemble MT Tumbler 200. Bud Trimmer

Gasinosinotrimmer with a D-shaped handle is more maneuverable, it is convenient for them to mow grass in areas with a complex relief. In such a tool, the hands are located one above the other. The lack of a handle is difficult to hold, control of such a device is more complicated.

The handle in the form of the English letter “j” is the most uncomfortable, so it is rare.

How to remove and disassemble a coil

Before proceeding to the process of replacing the cord, users of trimmers need to remove and disassemble the coil. Consider how to do it.

The mowing head of a trimmer for grass consists of several parts: a casing, springs (not in all models), bobbins with a cord and cover.

Attention! Before proceeding with any actions to maintain an electric unit, it must be disconnected from the network.

Trimmers most often use 2 options for fastening a mowing head.

disassemble, rogue, trimmer, champion, grass

Option

To remove the head of the trimmer for the grass, it will require its complete disassembly.

Chapur. Herramientas de confianza

Option

In this version, the head is twisted onto the gear shaft. To remove it, you need to fix this shaft. To do this, in such trimmers, for example, in the Huter and Champion devices, a hole is provided through which you can insert either a thin screwdriver or a metal rod.

So, to remove the bobbin, take 2 simple steps.

  • Insert the screwdriver into the hole and stall the shaft.
  • Take the head of the head and start twist it clockwise. It should be twisted in this direction for the reason that the thread cut on the shaft is left.

Is it possible to make a coil for a trimmer for the grass with your own hands

On sale there are a large number of trimmer heads (not automatic), which have a low price and good quality. But sometimes situations arise, for example, in the country, when the trimmer coil broke, and its repair is impossible, the store is far away, and you need to mow. In this case, you can quickly, literally in a few minutes, make a simple trimmer nozzle to fix the fishing line from ordinary plywood 10-12 mm thick.

  • Take a piece of plywood or textolite and draw a circle with a diameter of about 14 cm on it.
  • Cut the disk with a jigsaw or hacksaw for metal.
  • Drill a hole in the center of the disk, suitable in diameter to the gear shaft. Do not forget before installing a disk on the shaft, put a puck on it.
  • You can fasten small corners along the edges of the disk or make 1-2 holes on the opposite sides. They will serve for refueling fishing lines in them.
  • To fix the fishing line for a trimmer, you can screw several screws into the plywood.
disassemble, rogue, trimmer, champion, grass

Such a homemade mowing nozzle is fixed on the shaft with a nut. Twist or unscrew the nut without fixing the shaft will not work. To replace the cord, it will be enough to release the screws, insert a segment of the fishing line of the required length and press it again.

Also, a mowing nozzle for fixing the fishing line on it can be made from a metal sheet. How to do this can be understood from the next video.

Types of trimmer heads

Also, a different device can have a braid for grass: with carboards of fishing line, semi.automatic or manual. In the first case, in order to lengthen the working ends of the thread, it is necessary to reduce the speed slightly. And when you add them again, the fishing line for the trimmer will extend automatically. For semi.automatic devices you need to click on a special button located below. trimmer for grass while turning off is not necessary. Just knock a scythe on the ground just. The most inconvenient in work are trimmers for grass with manual supply of a string. To lengthen its working ends, the tool must be turned off and the operation manually performs the operation.

Another coil with a fishing line for a trimmer for grass happens:

  • one.stringent. suitable only for cosmetic trimming of the adjoining territory;
  • two.string. used for more serious work to clean the site from grass.
  • From thin, but durable plastic, you need to cut the ring, and its inner diameter should be equal to the thickness of the core, on which the fishing line for the trimmer is wound, and the outer. the diameter of the coil is wound.
  • On the inside of the ring, you need to make a small recess through which the thread will last.
  • Next, the ring is cut, put on the coil. And the cut place is glued with tape or soldered using a hot knife. That’s all. now each end of the fishing line can be wrapped on your part of the coil.

Instructions

In order to change the fishing line for the trimmer, it is necessary to extract the old one (if it was).

The coil is part of the design of the trimmer for the grass, which is located inside the head of the motorcosa, drum or bobbin. Depending on the manufacturers of the head can be different. But this article discusses only Patriot, although their mechanism is used by many other companies.

Now you need to understand how to properly remove the head from a trimmer for grass and how to get a drum out of it.

Eliminate the malfunctions of the automatic coil with a fishing rod for a lawn mower

Instructions on how to promote a hand head on a trimmer is described below.

  • First of all, you need to clean the head of dirt and adhering grass if it is contaminated. To do this, you need to raise a motorcycle head up and, holding the casing, remove a special protective cover dressed on the drum.
  • The next step needs to remove the reel from the drum. The coil is easily removed even with one hand, because it is not fixed inside the drum.
  • The drum itself is fixed in the trimmer with a bolt. This bolt must be unscrewed, after which you can easily pull out the drum. To do this carefully, you should support the drum with a coil, while twist the screw counterclockwise.
  • Now you can pull the coil out. As mentioned above, it is not fixed in anything except a hook with a metal shaft, so it does not need to be torn off with force. Neatly, in a circular movement you should pull the coil from the drum.
  • Now it remains to extract an old fishing line for a trimmer and follow the following instructions.

Installation of the coil and drum in its former place is performed according to the opposite algorithm.

Before the process of refueling the fishing line, it is worth making sure that the thread suitable for a trimmer was bought. In the case when the thread is not suitable, the fuel or energy consumption increases, as well as the load on the motor motor.

In order to replace the thread itself directly, you need to prepare a piece of thread of the required size. Most often, this requires about 4 m fishing line. A specific figure will depend on the parameters of the thread, for example, its thickness, as well as on the parameters of the coil itself. If it is not possible to accurately determine the length, it can be done as follows: insert and wind the thread to such a state that the coil is completely charged (the level of the fishing line will be compared with protrusions in the sides of the coil). It is necessary to ensure that the fishing line for the trimmer sits in the coil exactly.

Do not forget that the thick thread will be shorter than thin.

The instructions for refueling the fishing line in the coil is described below.

The prepared thread must be taken and turned in half. It should be ensured that one edge is longer than the other by 0.1-0.15 m. Now you need to take the ends in different hands. The one that is smaller must be pulled to more, so that it becomes 2 times shorter. When bending, the indentation should be maintained at 0.15m. Find the slot inside the coil partition. Carefully prick the loop that turned out earlier in this slot. To continue work, it is necessary to determine the direction of winding the thread in the coil. To do this, just examine the coil. there should be an arrow on it. If the gunner could not be found, it is quite possible that there is a written designation. An example is given in the photo below. It is necessary to inspect the head of the coil. It has a direction indicator. However, this is the direction of the coil movement. To get the direction of winding, you need to wind in the opposite direction. Now you need to season the reel with a fishing line

It is worth noting that there are special guide grooves inside the coil. When wrapping a thread, you need to follow these grooves, otherwise you can damage a trimmer for grass

At this stage, you need to charge the coil very carefully. When the user winds up almost the entire thread, you should take the short end (do not forget about the protrusion of 0.15m) and stretch it into the hole located in the coil wall. Now you need to repeat this action similarly with another end (on the other hand). Put the coil itself in the coil head, before that, extinguishing a fishing line for a trimmer through the holes inside the drum. Now is the time to return the drum to your place. After that, you need to take with both hands by the ends of the fishing line and pull them to the sides. Then you need to put the lid in place (here you can safely make efforts until a characteristic click is heard). Remained to perform “cosmetic work”. You need to see if the thread has come out too long. You can start a trimmer for the grass and check in practice whether everything is comfortable. If the thread came out a little long, you can cut it with scissors.

Tips and recommendations how to wind a fishing line for a trimmer and what you need to know

There are several useful tips and recommendations that it will be useful to find out not only beginners, but also experienced masters-codes. These tips will help prevent negative consequences in the form of injuries and improper functioning of the mechanism. These recommendations say the following:

  • Set the lid to clicks. over, these are 2 or more clicks, which depends on the number of fixers. If one latch does not click, then when starting the tool, the drum can jump out and injure a person
  • Do not wrap a fishing line for a trimmer with its strong pulling, as well as in an amount more than you can insert it into place. It is better not to harvest the equipment than it will be more, as this will lead to negative consequences in the form of the impossibility of unwinding it if necessary
  • If you own the tool not with two conclusions of the fishing line, but with one (usually low.power units), then the winding process is performed in a similar sequence, as described above, only with the difference in the absence of the average side between the extreme bases of the coil
  • After replacing the material, it is necessary to first check the tools of the tool, and then proceed to the mocking of the grass. If you do not make a preliminary check, then the forests can be unwound, and injure a person

It is interesting! Choose the material of the appropriate quality so as not to get injuries when working with benzo.cards, trimmers and motorcycles. In the process of beating grass, small stones and other materials fall under the rotating parts, which can fly over long distances, therefore, despite the fact that the fishing line for a trimmer is not a knife, working with a tool should be carried out in protective special uniforms.

The result of the work done is as follows. after the replacement of the new material is enough for an area of ​​up to 600 square meters, but when taking into account the presence of a reinforcing layer on the fishing line

Ordinary nylon materials serve less, which is important to take into account when working. Do not try to mow thick.button grass with fishing line, as there are special metal wheels or knives for this

Publications

Tires for chainsaws. types, choice and replacement

What are trimmers for grass and what is better to choose pros and cons of

How to repair a starter on a chainsaw

The main malfunctions of the coil

Users of electric trimmers and black cutters often face the problem of semi.automatic mowing. Coil malfunctions can be as follows:

The fishing line for the trimmer does not expand automatically

If the fishing line for the trimmer is not lengthened by the light touch of the trimmer button for the grass to the ground, the reasons for this may be the following.

Option 1. there was a bite, t.E. Clamping cord between turns. This problem usually occurs if the user wraps a fishing line for a trimmer to a coil unevenly with a cross section of the turns or wraps it with insufficient voltage. In the latter case, when the mower rotates at a high speed under the influence of centrifugal force, the cord begins to contract, which leads to a possible twisting of a braid fishing line. To eliminate the problem, you will have to disassemble the coil in the trimmer for the grass and correctly rewind the cord, that is, in equal speeds with good tension.

Option 2. too short ends stick out of the head. When hitting the ground, the rod may not fall out if its ends protruding from the head are not long (short). In this case, centrifugal force is not enough to stretch the fishing line for the trimmer. Therefore, it is necessary to stop the unit (turn off the engine or disconnect the electric trimmer for grass from the mains) and pull the fishing line for the trimmer manually, first pressing the button.

Option 3. Field for a trimmer Spasyan inside a mower. This makes the coil stop and do not rotate when you press the button. This is mainly due to several reasons: the poor quality of the cord, overheating of the coil during continuous operation of the machine and the effect of a mowing fishing line on hard objects.

  • In the first case, the lace of third.party manufacturers can be made of low.quality and fusible materials that do not withstand mechanical and thermal loads. Therefore, it is necessary to give preference to “branded” fishing.
  • But if you still bought a fishing line for a trimmer of unknown quality, and it is often soldered during operation, you can follow the example of some users who, after filling the cord in the reel, moisten it or silicone lubricant (from the spray can) or mineral oil). This procedure significantly reduces the likelihood of soldering between the turns of the mowing fishing line.
  • A fishing line for a trimmer can also be soldered if during a mowing it falls into a solid object (stone, fence, dry branch, etc. D.). As a result, it stretches slightly and stretches to the head at high speed. The cord heats up from friction, and its coils stick together. The only thing you can do to solve this problem is to open a trimmer to the grass and rewind a fishing line for a trimmer.

The cord involuntarily lengthens

There are situations when a user of a trimmer for grass notices very quick fishing line consumption. However, he never pressed the button on the ground to lengthen the fishing line for the trimmer. The reason that the fishing line for trimmer involuntarily lengthens, cutting off a special knife on the device case, there may be a lack of spring in a mowing head. Often beginner users of mowers, trying to charge a fishing line for a trimmer in a coil, forget to install a compression spring in the head or even lose it when opening the lid, and in the future they will not even find out about its existence.

The main malfunctions of the coil

Users of the electrimmer and lawn mower often face a problem associated with a semi.automatic braid head. Coil malfunctions can be as follows:

The fishing line for the trimmer does not extend automatically

If, with a light blow, the trimmer coil button for grass on the ground is not lengthened for a trimmer, then the reasons for this may be the following.

Option 1. there was a snack, t.e. Squeezing the cord between turns. This problem usually appears if the user wound a fishing line for a trimmer to the coil unevenly, with the intersection of the turns, or wound it with insufficient tension. In the latter case, when the mowing head is rotated at large revolutions under the influence of centrifugal force, the cord begins to drag on, as a result of which the interitral clamping of the fishing line is possible. To eliminate the problem, you will have to disassemble the coil on the trimmer and rewind the cord correctly, that is, with even turns with good tension.

Option 2. too short ends protrude from the head. A fishing line for a trimmer may not exit when hitting the ground, if its ends sticking out of the head, insufficient length (short). In this case, the centrifugal force is not enough for the fishing line for the trimmer to stretch. Therefore, it is required to stop the unit (drown out the engine or turn off the ethletric trimmer for grass from the network) and pull the fishing line for the trimmer manually, after pressing the button.

disassemble, rogue, trimmer, champion, grass

Option 3. a fishing line for a trimmer was soldered inside a mowing head. This leads to the fact that the coil is stopped and does not spin when the button is pressed. Basically, this happens for several reasons: poor quality of the cord, overheating of the coil with prolonged operation of the unit, a fishing line on solid items.

  • In the first case, the cord of third.party manufacturers can be made of low.quality and fusible materials that do not withstand the mechanical and temperature load. Therefore, preference should be given to “branded” fishing.
  • But, if you still purchased a fishing line for a trimmer of unknown quality, and it is often soldered during operation, then you can follow the example of some users who, after refueling the cord, moisten it either with silicone grease (from the spray can) or mineral oil). This procedure greatly reduces the likelihood of soldering a fishing line among themselves.
  • Also, a fishing line for a trimmer can sleep if during a mowing it hit a hard object (stone, fence, dry branch, etc.D.). As a result of this, it is slightly stretched and draws back into the head with high speed. The cord is heated from friction, and its turns are sticking together. The only thing that can be done to eliminate this malfunction is to open a trimmer coil for grass and rewind a fishing line for a trimmer.

The cord spontaneously lengthens

There are situations when a user of a trimmer for grass notices a very fast fishing line consumption. At the same time, he never hit the ground with a button to lengthen the fishing line. The reason that the fishing line for a trimmer spontaneously lengthens, cutting off a special knife on the casing of the device, may be the absence of a spring in a mowing head. Often beginner users of mowers, trying to charge a fishing line for a trimmer into a coil, forget to install a clamping spring in the head, or completely lose it when opening the lid, and in the future, they do not even suspect its existence.

The technical properties of the cord and the selection of diameter by the power of the trimmer for grass

If you take the packaging of the fishing line in your hands, then only two main parameters are indicated on it. this is the total length and cross section. Instructions on how to choose a fishing line for a trimmer for a trimmer for grass is not attached, so you have to find out from specialists. Finding a good specialist is not so simple, especially since every year not only new fishing lines, but also coils are produced every year.

Read how to knit a fishing line for a trimmer for a lawn mower

The first thing to solve is the diameter, thickness or cross section of the cord. All this is one parameter characterizing the performance of work by trimmers, benzocouses, motorcycles and travo.shirts. What sections to buy a fishing line for a trimmer for your trimmer for grass? In order not to make a mistake, you should take with you a segment of the old cord, and provide it to the seller. Based on the segment you provided, the seller will give a similar cross section the cord.

This option is certainly reliable, but it is impossible to call it correct. Why? After all, the choice of fishing line depends not only on the head used, but also on the power of the tool used. To begin with, it is recommended to solve what diameter the fishing line for the trimmer can be used on trimmers and benzocoses, depending on their power parameters:

  • Electric trimmers for grass with power indicator up to 500 W. cords with a cross section of up to 1.6 mm are used.Such tools are designed to cut young grass in personalities
  • Gasoline and electrical units with power indicators from 500 to 1000 W. involve the use of cords with a thickness of 2 to 2.4 mm.Such units with consumables are used to prick thin and thick grass, as well as weeds. In trimmers for grass up to 1 kW, you can install a fishing line for a trimmer with a diameter of 1-1.6 mm, but at the same time it will be quickly wear out
  • Trammers for grass and lawn mowers with power indicators over 1 kW. allow the use of the cord with a thickness of 2.4 to 3.3 mm.Such fishing line can cut thick and dried stems, as well as thick thickets. If the consumable material with a thickness of more than 3 mm does not cope with the task of cutting grass, then metal disks with blades, teeth and knives are used

It is interesting!Manufacturers produce a trimmer fishing line for a trimmer with a diameter of more than 3.3 mm, only it is extremely rare, and exclusively on powerful gasoline units.

Is it possible to make a coil for a trimmer for the grass with your own hands

On sale there are a large number of trimmer heads (not automatic), which have a low price and good quality. But sometimes situations arise, for example, in the country, when the trimmer coil broke, and its repair is impossible, the store is far away, and you need to mow. In this case, you can quickly, literally in a few minutes, make a simple trimmer nozzle to fix the fishing line from ordinary plywood 10-12 mm thick.

  • Take a piece of plywood or textolite and draw a circle with a diameter of about 14 cm on it.
  • Cut the disk with a jigsaw or hacksaw for metal.
  • Drill a hole in the center of the disk, suitable in diameter to the gear shaft. Do not forget before installing a disk on the shaft, put a puck on it.
  • You can fasten small corners along the edges of the disk or make 1-2 holes on the opposite sides. They will serve for refueling fishing lines in them.
  • To fix the fishing line for a trimmer, you can screw several screws into the plywood.

Such a homemade mowing nozzle is fixed on the shaft with a nut. Twist or unscrew the nut without fixing the shaft will not work. To replace the cord, it will be enough to release the screws, insert a segment of the fishing line of the required length and press it again.

Also, a mowing nozzle for fixing the fishing line on it can be made from a metal sheet. How to do this can be understood from the next video.

Classification according to the method of refueling

The head for a trimmer for grass can have several ways to refuel the fishing line:

  • Quickly charged. The new cord is wound without analysis of the coil, that is, you do not need to remove it from the device. The end of the new element is touched into the coil and then wound a certain number of times. Upon reaching a specific value, the cord is cut off. Fine head for Trimmer for grass this type is produced by Shindaiwa and Speed-Freed.
  • Collapsible. Here the name itself speaks for itself. To replace the new cord is necessary take off coil from the equipment, then unwind the old fishing line for the trimmer and wind up a new.

Design features

It should be noted that the cutting head for Trimmer for grass Contains special arrows. They allow you to perform rotational coil movements in different directions. If there is a need to wind the fishing line for the trimmer towards rotation of the shaft, it turns into a specific position. A large number of wound cord threaten equipment breakdown. Two arrows are contained only on imported models. Now the heads are presented on the market with one arrow.

If the cord is not wound after the semi.automatic head, then its previous winding is incorrect. That is, after the head for a trimmer for the grass was installed, the user did not pull the ends of the fishing line from the grooves. Another unpleasant moment in the beard of grass may be sintering the coil turns. Why is it happening? This happens when there is a cord with a solid subject. At the same time, it brakes sharply and, with the subsequent movement, the fishing line for the trimmer begins to go inside the device. Thus, it gets on the rogue and sticks together. Because of this, the employee has to take a break and correct the situation. However, this can be avoided. Before installing the coil, it is necessary to treat the fishing line for the trimmer with a special silicone substance.

For various models of trimmers, semi.automatic head, consisting of two parts. housing and spray. Both elements contain springs. The second part can be performed in several versions:

  • single.section. both parts of the fishing line are wound together;
  • two.section. each end is wound on a certain part; This type is the most effective, since the fishing line for the trimmer is not confused and does not sinter.

There is a simple and cheap way to turn a single.sectioned spool into a two.section. For this you need a strong plate. From it you need to cut a circle, the diameter of which should be equal to the thickness of the buffet. In this case, the thickness is taken near the place where the fishing line for the trimmer is wound. This circle moves freely. Next, a cut is made on the ring, put on a spool and is connected using glue or tape. As a result, you can wind a fishing line for a trimmer to the required section. The head for a trimmer for a universal grass can have from two to four holes that are located opposite each other. Mowing ends come out of them. In addition to the presented coils, there are heads where a certain size of the fishing line is inserted. In this case, the number of mustos increases to twelve. Many users believe that such a device is quite convenient. However, not all people adhere to this opinion. They believe that in this situation the fishing line will have to spend more. In addition, to replace it, it is necessary to stop the workflow. The head for a trimmer for grass, the caliber of which can be varied, is suitable for haircuts of grass, shrubs and trees. Before purchasing a trimmer for grass, it is necessary to study the area, as well as the features of the equipment. So, we found out why the head for the trimmer for the grass is universal and how to correct it correctly.

| Denial of responsibility | Contacts |RSS