How to drift the wall with a drill correctly. Conductor for drilling holes without dust

Tips on how to drill a concrete wall with a regular drill

Usually a peorator is used to drill monolith. However, this tool is far from always present, and it will not work if the following situations arose:

Therefore, for practical use in an ordinary apartment, it is more advisable to drill concrete walls with a regular drill. When acquiring it, you need to take into account certain nuances:

Nozzles

For drilling a monolith drill, it is necessary to purchase the appropriate nozzles. The following products are suitable for this:

  • Rosted crowns. They provide a drilling function. It is advisable to buy varieties in which separately soldered teeth, since they are made from durable metal alloys.
  • Diamond crowns. Such products will be able to perform holes without strike. These nozzles are improved, they allow you to get a hole much faster. The crowns are equipped with curly cuts, they have an abrasive structure on their edge. It is enough for the master to only choose the necessary tool length. In everyday life, varieties are usually used whose diameter does not exceed 120 mm.
  • Special concrete drill. They freely manage to drill a monolith in which there is no reinforcement.
  • CS: GO crowns, which have a cutting edge, the surface of which has a diamond abrasive applied by the thermal method.

Starting the use of the purchased nozzle, it is first recommended to check whether electric wires, reinforcement are present in the wall. It is convenient to do this with a device that determines the presence of metal. Thanks to such preparations, it will be possible to protect the nozzle from the breakdown, and the concrete wall will not be strongly destroyed.

Ways to drill brick

Drilling a brick wall can be carried out in one of three ways:

The first method is the simplest, but less technological. It is used if the master does not have appropriate equipment. Electromechanical technology allows you to cope with drilling in a shorter time. For this, a peorator or drill is used just. As for automatic drilling, with its help you can make holes of an impressive diameter. Up to 110 mm.

Manual method of drilling

Drilling holes in a brick wall using this technology is carried out if there is no electrical equipment. All that you need is a hammer and a hukebur. The latter is a metal tube that can be made with your own hands or purchased in the finished form. If you resort to the first decision, you will need to prepare a piece of 30 cm. The diameter of such a device should be 25 mm or more. At one end of it, Zazubins are made.

wall, drill, conductor, drilling, holes, dust

The technology suggests itself, if you present these tools: as soon as the place of making the recess is determined, the hukebur is installed at right angles to the wall, and at the other end it should be hit with a hammer. The nobleburn is turning, which will eliminate the formation of a large amount of dust.

How to drill tungsten carbide

Electromechanical drilling technology

In order to drill the wall in a shorter time, you should use the technology that provides for the presence of a master of a drill or a penetrator. In the first case, you need to make sure that the equipment has a shock function. Otherwise, you have a long and monotonous work, which, in addition, may not allow to achieve a positive result.

The ease of process will depend on how much revolutions and power in the tool. The most suitable value of the number of revolutions is 2000 or more. With an increase in this parameter, you can count on the fact that the hole can be made in the shortest possible time. If you only plan to purchase a drill, it is important to make sure that it has a quick.Linking cartridge and a reverse function. In the first case, you do not have to additionally use the clamping key.

Brick drilling can be carried out through. For this, a pedulator with diamond crowns is often used. The working part of the equipment should have rounded edges. This equipment should also have an option to strike. In order to prevent a large load on the peorator and consumables, if it is necessary to make holes of an impressive diameter, you should start with small drills, finishing the work with large.

If there is warm ceramics or hollow products, you need to turn off the shock function, as this can destroy the material. If the brick has a high brand and good strength, as for clinker products, the electrical device is installed for average speeds, otherwise the equipment may be dull.

Attention! If the wall needs to be drilled under the installation of hoods, sockets or water supply systems, diamond drilling should be used. For this, a crown with particularly strong teeth is selected for this. If you use it by involving a tool in impact mode, this can lead to the fact that the base will be torn. In order to exclude such a nuisance, you need to start drilling with the masonry seam.

See also  How to remove the drill chuck from the cone

Automatic brick drilling

If the brick wall needs to be drilled in an inaccessible place, for example, in the corner or you need to do an impressive diameter, ordinary tools will not help. Automatic technology should be used here, which provides for the use of special installations.

Usually in the process crowns with a diameter of 2 cm or more are involved. Drilling depth can reach 4 m. This technique is good for noiselessness, and 1 cm of thickness can be overcome in a few tens of seconds. For the operation of such equipment you need water and connection to the mains. The tool is strengthened on the vertical surface, then water is supplied to the drilling site. Work is carried out automatically without human intervention.

Classification and features of concrete drill

When you figured out whether all kinds of devices can be used, including a drill to drill concrete, you should familiarize yourself with what features have drill. All of them usually have carbular tips, which provide strength to the material and products. Such consumables are called winning and can be intended for a drill or peorator. In the first case, the equipment has a multifaceted or cylindrical configuration.

You can find out the peorater equipment by sds-plus designations or.Max. You can drill concrete with the frame inside using the shock function of the tool, using the drill:

With the help of the first, you can drill concrete to an impressive depth. If necessary, make holes of impressive diameter, use a drill of a second type. If you need to drill a concrete plate to a slight depth and diameter, you need to purchase a gentle consumable.

Many people think about whether it is possible to make holes with a diameter of up to 100 mm and more. The answer is positive. If you are also from among the masters who set a similar task, you should purchase a crown that can have diamond spraying or winning cutting part.

Attention! When drilling holes in concrete, you will have to choose a certain diameter of the equipment. With an increase in this parameter, the length of the drill will become larger. This is due to the fact that a thin and long consumable will not perceive impressive loads.

How to drill a wall

Before drill a hole in the wall, you must familiarize yourself with the algorithm for conducting work. At the first stage, marking is carried out. Then you can proceed directly to the process itself. First, the tool turns on several times to outline the future hole. In the process, the drill should be periodically removed, and the tool should be allowed to rest so that the equipment does not overheat, and the engine does not fail. Some masters dipped a drill into cold water.

How not to get into the wire

First you need to ask where the wiring is located in the wall. This will help you with the electrical wiring scheme. If it was not possible to find it, you must think about how not to get into communication.

To determine the location of the wires, you need to use the detector. It is applied to the place where it is supposed to be drilled. The device, however, has an error of several centimeters. In order not to get into the wiring in the ceiling, you should see where the lighting device and the switch are located. From the first to the second, the wiring goes along a flat trajectory without tilting.

In order to exclude unpleasant consequences, the wiring before starting work must be de.Energized. Then, if you could not get into communication, at least you exclude the risk of a shock. Now you know how not to get into the wiring when drilling a wall. But immediately after the completion of the manipulations, the machine should be turned on. If it does not knock it out, everything is in order, and the wiring remains in integrity.

Drilling holes in reinforced concrete

On the surface of the wall, marking should be made. The tool first turns on at low speeds to make a small recess. When it is supposed to install plastic dowels, the hole needs to be made a little deeper. It is important to consider that dust will accumulate inside the recess, which is not always realistic to remove from there, so when calculating the depth, a small stock should be laid.

Drilling tiles

When the choice of drill has already been made, you can proceed to work. If you have a wall trimmed with tiles, you need to prepare some tools and materials:

When the recess is supposed to be made small, you should stock up on the equipment, which is known among the masters as a ballerinka. In the central part of the future opening, the enamel of the cladding is slightly broken up, for this the tool is installed at low speeds.

At the point of drilling, the island is glued so that the drill does not slip. An alternative and more technological solution is the use of a conductor, which is a board with holes.

Attention! It is better to drill into a concrete wall in a blow mode, but in the case of tiles this cannot be done in any way. The absence of this mode ensures the neat operation of the drill.

First, the tool is turned on at low speeds, and then the rotation speed increases. With the help of a vacuum cleaner, the second person will immediately remove dust from under the equipment.

wall, drill, conductor, drilling, holes, dust

Drilling holes of large diameter in the wall

When you do not plan to get into the wiring and know how to avoid this, you should also ask how to make a hole of an impressive diameter. If you work in accordance with the recommendations, the result will justify expectations. If necessary, make a hole at 150mm, you should use the winning drill. If this parameter should be higher, you need to purchase a screw boat.

See also  How to grind a tree with a drill. Features of work

Drilling depth limiter

When choosing such components, you need to be guided by the diameter, which should turn out in the end. This element consists of two parts, one of which will contact the surface and will not damage it. Typically, such a limiter is purchased with a screw fixation. The uniqueness of this addition to the instrument is that it eliminates the skew of the drill. Included with this device is a playback key. It is fixed on the drill.

Accurate drilling holes

Sometimes when drilling holes in the wall requires high accuracy. In order to achieve a positive result, you should glue a sheet of sandpaper by the conductor. The area of ​​the element will be affected by the area where the future hole is located. This will increase the clutch of the wall with the device, and the master will be able to make a recess in the place where it is necessary.

How to drill a perpendicular and vertical hole

Although sometimes it is necessary to drill at an angle, vertical holes are most often made (that is, perpendicular surfaces). In order for the drilling to take place strictly at an angle of 90 degrees, it is necessary to use special guides. They will allow drilling perpendicularly, without deviating in any direction.

The simplest guides make it possible to make only vertical holes, but there are more complex structures that allow drilling at certain angles.

Than drill the wall

The best tool than the peorator for drilling holes in the brick and concrete walls has not yet come up with. But rarely anyone can afford to have a luxury to have such an expensive tool on the farm. Usually buy an electric drill of shock action.

The choice of a drill

When buying an electric drill, you must be guided below by the following technical characteristics.

The power of the drill should be at least 600 watts. Revolutions up to 2500 per minute and the possibility of their smooth adjustment from zero to maximum. The presence of a rotation reverse (switch of direction of rotation of the drill clockwise or counterclockwise). The cartridge is best fast.Packed, it will not be necessary to spend time on the click of drill and the search for a constantly lost key. The diameter of the drills clamped in the cartridge up to 12 mm.

The presence of the inclusion function with a blow. Of course, the drill when this function is turned on will not become a full.Fledged peorator, but drilling the walls will be much easier and faster and that’s why. Brick, cement and concrete are very well withstanding a static load. Pressure. But easily destroyed from dynamic influences. Impact. Karatists, due to a strong blow, easily break the brick in two of the edge of the palm. When driving a drill without a function of impact, a simple pressure of the drill and cutting edge is difficult to catch on the material, so the drilling goes slowly and the drill from friction is greatly warmed up. Completely differently take drilling with a blow. The drill, when impact, crushes part of the material with the cutting edge, and, falling with a blow to the depression formed, breaks off a portion of particles of the material. Something happens on the likeness of a chisel of a chisel.

The choice of drill

Walls made of wood, drywall, foam concrete are successfully drilled by ordinary drill. For walls made of brick, stone or concrete, a carbide drill is already needed. It differs from steel, it differs on a conventional drill with cutting edges of carbide material, usually winning. Less commonly artificial diamond.

The winning insert is clearly visible at the end of the upper drill. It is enough to have 2 winning drills with a diameter of 6 and 8 mm on the farm.

Drill with a winning surfacing can drill a hole with a depth of not more than 10-15 cm. For drilling to great depths, for example, to drill the wall through, use a drill. Boers for drilling brick and concrete walls are up to one meter long and are designed to drill holes only by a pedorator. In the drill, even the cutting edges are made not sharp, but rounded to increase their wear resistance. A drill with a penal function can also be successfully drilled with drill.

I am drilling rooms with a shank diameter of 10 and 18 mm, with special grooves of the SDS or SDS-Max standard for fixing, but in the usual fist cartridge are also well clamped. The standard and diameter of the drill are knocked out on its shank.

How to use a diamond core drill

If you need to go through a thick wall with a drill, for example, half a meter, then the passage is performed in several stages with drilling with one diameter, but of different lengths. This is necessary for safety and faster drilling. First, the wall is drilled with a drill with a length of 20 cm to a depth of 10-15 cm, then a longer drill to a depth of 30-35 cm and end with drilling with a length of 50 cm. The drill for such work should be quite powerful. Of course, the drill for such a load is not calculated and its use is permissible only in exceptional cases. It is better to carry out this kind of work, to rent a real peorator.

See also  When drilling than to lubricate the drill. Drilling stainless steel in industrial and home conditions

The choice of tools

Drill drill

Usually a peorator is used to drill monolith. However, this tool is far from always present, and it will not work if the following situations arose:

Therefore, for practical use in an ordinary apartment, it is more advisable to drill concrete walls with a regular drill. When acquiring it, you need to take into account certain nuances:

Nozzles

For drilling a monolith drill, it is necessary to purchase the appropriate nozzles. The following products are suitable for this:

  • Rosted crowns. They provide a drilling function. It is advisable to buy varieties in which separately soldered teeth, since they are made from durable metal alloys.
  • Diamond crowns. Such products will be able to perform holes without strike. These nozzles are improved, they allow you to get a hole much faster. The crowns are equipped with curly cuts, they have an abrasive structure on their edge. It is enough for the master to only choose the necessary tool length. In everyday life, varieties are usually used whose diameter does not exceed 120 mm.
  • Special concrete drill. They freely manage to drill a monolith in which there is no reinforcement.
  • CS: GO crowns, which have a cutting edge, the surface of which has a diamond abrasive applied by the thermal method.

Starting the use of the purchased nozzle, it is first recommended to check whether electric wires, reinforcement are present in the wall. It is convenient to do this with a device that determines the presence of metal. Thanks to such preparations, it will be possible to protect the nozzle from the breakdown, and the concrete wall will not be strongly destroyed.

How to choose a tool

Most often, peorator is used for concrete drilling. It has several advantages over a conventional drill.

Despite the above advantages, such a tool is not always suitable for work. In some situations, its use is simply inappropriate.

The peoporator is not suitable in the following cases:

  • When shallow holes (10–12 mm) are needed in the wall;
  • When working with foam block (otherwise the material will crumble);
  • If the required number of holes does not exceed 15 pieces.

Based on this, we can conclude that a regular drill is more suitable for home use. To purchase such a tool for drilling walls, you need to take into account a number of important points.

The drill is obliged to meet the following requirements:

  • It should be shock, since this type is most effective when drilling concrete walls. In an unstressed drill, the nozzle and cartridge will fail too quickly.
  • It is better to buy winning shafts with the purpose of the concrete work. And the tip. With a coating of strong alloys.

You can choose a drill-poorator. True, such a tool is more expensive than a regular model. But it has an increased power that can be adjusted at its discretion.

Safety precautions

Any construction or repair work is associated with certain risks, so it is important to know how to drill concrete without injuries. A number of rules should be followed:

  • First, it is necessary to check that pipes or electrical wiring are not laid at the drilling point. This can be done using a metal detector. If possible, turn off the electricity in the premises where the repair is carried out. The drill is connected to a separate outlet connected to the distribution shield. Under a decorative coating, a metal detector may not recognize pipes or wiring. Drill in such places with caution so as not to in vain to spoil the wall.
  • If the house has hidden gas wiring, then the gas must be blocked for the duration of work.
  • The seams in the block house cannot be categorically cannot be drunk. Communications often put in the channel between blocks in violation of the construction rules.
  • Be sure to check how the drill is fixed in the cartridge.
  • In the process of drilling, it is necessary to use protection products: glasses, gloves, overalls. If you plan to work on top, put on a headdress. When drilling, a lot of dust is released. It is necessary to use a protective mask or respirator.
  • With through drilling the wall, it is necessary to make sure that work is not carried out from the opposite side by another person.
  • If the hole must be made at the ceiling level, then the work is done not from the ladder, but from the forests or goats. The ladder is less stable. If there is no suitable support, then the stepladder is strengthened with stops.
  • You cannot include a tool that rests on the work surface. The pressure and revolutions increase smoothly.
  • For the stability of the tool, it is kept only by the handles. Holding a working drill for a cartridge is strictly prohibited.
  • In some regions there is a time assigned by legislatively, at which noisy work cannot be done. This must be taken into account when drawing up an action plan.

To obtain the skill, you need to drill a hole in concrete several times slowly and neatly. This will help to understand that, subject to nuances and safety precautions, this work does not cause big problems and difficulties. Even newcomers can perform it on their own.

| Denial of responsibility | Contacts |RSS