How to get a chausopila Husqvarna. Tools necessary for work

Husqvarna chainsaw repair with your own hands video

A key role in any chainsaw is played by a carburetor power unit of a two.Stroke type. Its power directly depends on the selected model and purpose. The second important mechanical node in the device is considered the saw part, which consists of a tire, a cutting chain and a chain wheel. Data parameters of the components may vary.

With lubricating mixing, it is carried out using special oil, which is poured into a specialized tank, it is located on a manual block. Separately, it should be distinguished that the volumes of the oil tank and fuel are calculated in such a way that their contents, as a rule, ends at the same time.

Fault options and elimination methods

Regardless of the brand of the chainsaw. Champion, Husqvarna 236 or Patriot, the reasons for poor work are identical. Options why the stihl chainsaw is not started, the mass is the following.

The chainsaw is poorly started on the cold

If the saw is poorly started on the cold, it means that it does not have compression. This is due to abrasion of rings due to long-term operation. It turns out when the user is trying to start Champion 137 in a cold state, compression for this manipulation will not be enough.

In this case, it is not recommended to systematically pull the handle. In the end, the unit will nevertheless start, but at the same time other mechanical nodes may break off. In this situation, you need to replace the erased rings with new.

The chainsaw is not started on hot

Here the reasons lies in the filing of the engine and get wet of the candles. Here’s what to do in such a situation:

  • Rearrange the air damper in the middle position;
  • Well make the components of the parts;
  • Start the device for 10 seconds;
  • Transfer into the mode of operation at idle;
  • On a chainsaw caliber or other model completely open the damper.

Next, just start the motor at idle with pulling the handle. If the engine does not overheat, it will easily start.

In the event that this option of eliminating the malfunction did not help, then the motor has already managed to cool strongly. Make a fiction of half.Gas according to the recommendations from the instructions and repeat the operation.

You should also try to scroll through the cold screw in the direction of movement of the clockwise. The higher the speed of the rotation in the equipment, the easier it is to start it. You should know that the chain at idle should remain in a stationary position.

The chainsaw is poorly started and stall immediately

In this situation, the reason is the filling of suppositories with gasoline at the moment when the user tried to turn on the unit. A small volume of fuel accumulates under the candle electrodes, which is why there is no spark in the equipment.

Removing a candle and its thorough drying will help to solve the problem. In addition to these actions, you can additionally fragment. But this manipulation should be carried out exclusively using a gas burner. In another case, a small cargo in the field of electrodes may form. After complete drying of the candles, you need to drain the excess fuel and leave to dry the equipment itself.

Chinese saw does not start

It should be noted right away that Chinese devices do not have a distinctive features from other analogues. They are also reliable and productive, moreover, they cost less. The only thing that is necessary for this device is necessary is to use only branded oil and fuel.

Most units do not work well on the fuel of domestic manufacturers, gasoline clogs channels and, as a result, fuel does not enter the motor. Use fuel either of high quality or from the manufacturer of the saw itself.

Why is the new saw not working

New equipment should not have problems with the wear of functioning mechanical parts, since the model came out only from the conveyor. Such untidiness may occur in the case of the acquisition of demonstration technology, which was more than once used to advertise the company. The cause may also be improper operation of the unit, which does not comply with the recommendations from the instructions.

First of all, you should check whether all parts and components of the elements are installed in their places. Still, for example, Husqvarna will not start if the fuel mixture prepared without taking into account the necessary proportions was poured into it.

See also  Tools for clearing snow from the roof

But if all the recommendations are followed, each part is carefully recorded in its place and the equipment was not purchased from the stand, probably the buyer came across a defective device.

The tank is not enough fuel or it is of low quality

This is one of the most common reasons. Users of gasoline technology, in order to save, often use budget fuel. At first, the unit will regularly perform its work, but the problem will certainly arise after several months of operation.

Engine

Engine breakdown is one of the most common and laborious. This nuisance is manifested by such factors:

  • Unstable work at idle.
  • Does not start.
  • There is not enough power, or the Husqvarna 142 chainsaw will start and stalls as soon as it starts to gain momentum.

Before starting the repair of the Husqvarna 142 chainsaw, it is recommended to carry out full diagnostics of equipment to accurately determine the causes of problems.

The main reasons why the chainsaw is not started on the video. The video will be useful for those who quickly want to start a saw, the author gives practical advice.

In case of a situation where the chainsaw is not started, it is important to correctly conduct diagnostics, determine the direction in which the malfunction should be sought. Do not use a tool that does not work at idle, as this indicates the presence of air leaks into the engine and can lead to serious problems. If the experience in repairing the chainsaws is not enough, it is better to contact a specialist who will save your time and nerves.

Why not start and what to do

Among the malfunctions of the Husqvarna chainsaw, the engine is highlighted. The motor is either completely impossible to start, or it starts poorly.

Stihl VRS Husqvarna : Firewood Chainsaws

When asked why the chainsaw is not started, there is no unequivocal answer. The main assembly unit of the tool is the engine. The stability of the work is influenced by the following conditions:

For each factor, his working knot is responsible:

  • For the combustible mixture. Carburetor;
  • For the air. The cleaning system, in particular, an air filter;
  • For a spark. Ignition and candle mechanism;
  • Lubricant. Lubricant and gasoline.

The common reason that the chainsaws are not starting is referring to the non.Compliance of the launch algorithm. The motor unit should be launched only after the full assembly of all parts:

The brake of the chain is always turned on. In order not to lose control of the tool, you can not start in the air.

The launch of the motor in the cold state is carried out as follows:

  • Put the tool on the ground, step on the back handle with the right foot, the left hand is located on the front handle.
  • The saw is in a stable state, the chain does not apply to the soil.
  • Take the starter handle with the right hand, pull the cord, while it is not twisted around the hand.
  • As soon as the first outbreak occurs, they return the lever of the air damper to the initial position, opening it, and repeat the start.
  • Gas and release. The lock is turned off.
  • They transfer the engine to idle speed due to the rapid shutdown of the gas limiter.

The launch of a warm engine is carried out in the same sequence, but without opening the damper.

If the start is produced correctly, but the engine does not work, the possible reason is the absence of fuel in the tank, or the fuel chamber of the carburetor is not filled. Check the tank and the camera, fill them with the mixture.

If the incendiary system is faulty, the candle is inspected and checked for the presence of spark on the electrodes. If it is wet (gasoline floods the candle), and the spark is not detected, the part is turned, dried or changed. If it is dry, the spark is present, then the problems in fuel equipment are clogging, depressurization of the gas intake.

Magneto malfunctions are also confirmed by a weak spark. Despite the ignition, there may be no outbreak in the cylinder, while a candle turned out of the cylinder, wet. The method of elimination is the purge of the cylinder with open carburetor shutters.

The electrodes of the system are covered with soot or oiled. This is eliminated using a metal brush. The candle is washed, cleaned, giving gas to evaporate.

Violation of the gap between the side and central electrodes leads to a poor start. Normal interval indicator-0.6-0.7 mm. It is adjusted by the bending method.

In case of damage to the ceramic insulator surrounding the central candle, or live cores of wires, the wires are replaced.

If it starts and stalls

Husqvarna chainsaw starts and stalls when you press the gas. This leads the jacket of the carburetor jacket and the contamination of the fuel tank filter. The defect is eliminated as follows:

The next reason why the chainsaws stall is pollution of the muffler with exhaust resins. The issue is solved by cleaning.

See also  Tools for working with fabric by hand

How to understand Husqvarna Chainsaw model numbers. Bench Talk

Distance of piston rings affects the work of the cylinder.Piston group. In the presence of a backlash during the audit, the details are replaced.

When starting the engine, the unit may also stall:

  • With increased dryness, the channels supplying oil are cleaned, the elements of the connection of the fittings with the tubes are examined;
  • When oil leaks in the connecting points or the presence of cracks on the tubes are sealed with sealant.
  • If the piston rings in the grooves are buried;
  • With the wear and elasticity of the rubber sealing of the crankcase;
  • Leakage of the cylinder connection to the carder;
  • Due to improper installation of the ignition force angle;
  • As a result of contamination of the ribs of the cylinder and the fan lattress;
  • With strong load immediately after buying a new engine.

Features of maintenance and independent repair of chainsaws of the brand Husqvarna (Husqvarna)

Husqvarna chainsaws are indispensable assistants in the household. With the help of gasoline motorized equipment, different works related to construction, logging and simple cutting of branches can be performed. With proper handling of the tool, it will serve for a long time, but during operation as a result of intense loads, different failures occur in work.

If small breakdowns are detected, they do not turn to service centers and workshops, the current repair of the Husqvarna chainsaw is performed independently, while it is necessary to investigate and disassemble the likely causes of defects and ways to eliminate them.

Why is the chain not lubricated

Oil is not included in the saw set due to violation of the chain lubrication system. The reasons for this are as follows:

  • The presence of defects in the oil pump;
  • Clogged filter, channels;
  • Breathing defects;
  • Rupture of an oil hose;
  • Mismatch of the oil opening on the saw case and tire;
  • Gear gear malfunction.

The oil pump is responsible for the increase or decrease in oil consumption and is located on the right side of the chainsaw. Insufficient lubrication can occur due to leakage or pollution. It is removed after the clutch untwisting.

The oil supply to the circuit is regulated by the adjustment of the oil pump.

Why the chainsaw is not started?

If you did everything according to the instructions, and the chainsaws will not start, then something is wrong with her. This may be the fault of several of the most common reasons: there is no spark; fuel is not supplied; Air filter is closed. So, below we offer the procedure that will help to identify the reason why the chainsaws are not started.

Procedure if you don’t start a chainsaw

The first thing I would like to note if you don’t start a chainsaw is not twisting any screws on a carburetor. If you are not a specialist, then you still can’t set up something yourself and start a chainsaw will not work.

The following actions necessary, in order to start a chainsaw, take in the indicated order, starting to take action under the next number only if the previous one did not help.

  • For starters, just just leave the chainsaw at rest for 5-10 minutes. Perhaps during the factory she got a candle. This happens. Then try to get it according to the instructions again.
  • Remove the case cover on the chainsaw, remove the air filter and try to start without it. If the filter is contaminated, then it should be washed in soapy water and dried or replaced with a new.
  • Twist a spark plug from the chainsaw. Check the presence of a spark. If there is no spark, then try to put a new candle. If the spark never appeared, then this means that the ignition unit is damaged and the saw must be carried for repair. True, the visual observation of the spark does not mean that the ignition unit is working. If there is a spark, but the chainsaw did not work out, do the following on the list of action.
  • If there is a spark, but the candle is wet, then turn the chainsaw to drain excess gasoline from the cylinder if it accumulated there. Tighten 10-15 times a starter without a candle to ventilate the combustion chamber. Procate the candle and twist it back, or better change it to a new one, if there is. Try to start again according to the instructions.
  • If the candle is dry, then pick up one or two cubes of the gas mixture in the syringe and pour it into the cylinder. Try to have a chainsaw. Maybe a small snorinka got into the carburetor, which prevents the fuel from getting into the combustion chamber. This synchill will quite possibly eliminate the stream formed after the launch of the chainsaw by adding fuel directly to the cylinder.
  • Unscrew the muffler and remove it, trying not to spoil the gasket between the silencer and the engine. Try to get without a silencer and air filter. With the muffler removed from the chainsaw, you can inspect the piston from the inside. If there are burrs or bullying on the walls of the cylinder or piston, or the ring on the piston is clamped with burrs, then it will have to be very upset, as this means that the piston is damaged or worn out. This usually happens with underfilling in the fuel mixture of oil. With such a malfunction, you will have to contact the service, and it is possible to think about buying a new chainsaw, since replacing a piston is a fairly expensive operation.
See also  Hand-held electrical tools and equipment

Thus, we made out in this article how to start a chainsaw “according to the instructions”, and also what to do if the chainsaw is not started. We hope that these tips were useful to you.

Possible malfunctions

After the chainsaw appeared in the house, many owners breathed a sigh of relief.

With this tool, you can quickly and easily solve complex problems.

However, it should be noted that the chainsaw often breaks. This is due to the fact that during operation it is exposed to high loads. Therefore, it is always necessary to be prepared to eliminate damage.

Today there are a large number of workshops offering the repair services of chainsaws and other tools. However, this does not mean that in the event of a malfunction, you should immediately contact the maintenance station.

Some mistakes can be fixed with your own hands. To do this, you need to know only the indigenous causes of errors and ways to eliminate it.

For example, frequent use of the tool can lead to failures:

Each of these failures can be corrected with your own hands. The most important thing is to know the procedure for searching and eliminating faults.

Why the chainsaw is not started?

If you did everything according to the instructions, but the chainsaw does not start, then something is wrong. This may be due to some common reasons: lack of sparks; fuel is not supplied; The air filter is clogged. So, below we offer a procedure that will help determine the reason why the chainsaw does not start.

Procedure if you don’t start a chainsaw

The first thing to note if you do not launch a chainsaw. Do not tighten the screws on the carburetor. If you are not an expert, you still will not be able to adjust something yourself, and you will not be able to run the chainsaw.

Follow the following actions to run the chainsaw in the indicated order, starting from the next number, only if the previous one did not help.

  • First, try to leave the chainsaw at rest for 5-10 minutes. It is possible that the candle was filled during winding. It happens. Then try to start again in accordance with the instructions.
  • Remove the lid from the chainsaw, remove the air filter and try to run without it. If the filter is contaminated, it should be washed in soapy water and dried or replaced with a new.
  • Twist the light of the fuel from the chainsaw. Check for sparks. If there are no sparks, try to put a new candle. If the spark does not appear, this means that the ignition unit is damaged and the saw must be transported for repair. However, visual observation of a spark does not mean that the ignition unit is in good condition. If a spark occurs, but the chainsaw is still not working, follow the following actions in the list.
  • If there is a spark, but the spark plug is wet, turn the chainsaw to drain excess gas from the cylinder if it accumulated there. Pull the starter of the spark plug 10-15 times to ventilate the combustion chamber. Light a candle and tighten it back, but it is better to replace it with a new one if it is. Try to start again according to the instructions.
  • If the candle is dry, place one or two cubes of the gas mixture in the syringe and fill it in the cylinder. Try starting the chainsaw. There may be a small spot in the carburetor, which prevents fuel from entering the combustion chamber. It is possible that this will be displayed by the stream generated after the launch of the chainsaw, adding fuel directly to the cylinder.
  • Unscrew the muffler and remove it, observing caution so as not to damage the gasket between the silencer and the engine. Try to run without a silencer and air filter. Having removed the muffler, you can inspect the piston inside the chainsaw. If there are burrs or nests on the walls of the cylinder or piston, or the ring on the piston is hidden by burrs, you will have to be very upset, because this means that the piston is damaged or worn out. This usually happens when the oil is added to the fuel mixture. In this case, you will have to contact the service and, possibly, think about buying a new chainsaw, since replacing the piston. Pretty expensive operation.

Thus, in this article we discussed how to launch a chainsaw “according to the instructions”, and also what to do if the chainsaw does not start. We hope that you will find these advice useful.

| Denial of responsibility | Contacts |RSS