How to make a jack for a walk -behind tractor. Dimensions

How to make a jack for a walk.Behind tractor with your own hands

The dump is a necessary device, the need for which is at any time of the year. With the help of the front knife, snow is cleaned, planning, instillation of pits and moving bulk materials. Such equipment for the Neva motornote is of good quality, but not everyone can afford. Do.It.Yourself dumps require minimal financial investments. Having installed the front knife on the Neva one.Based tractor, you can solve many economic problems. In the presence of levers and hydraulics, a home.Made shovel can also be used as a loader.

For the manufacture of the dump you need the following tools:

  • Roulette;
  • Welding machine;
  • Electric drill;
  • Corner grinder;
  • Spanners;
  • Acrylic paint;
  • Barrel 200 l;
  • Reinforced rubber;
  • Sheet steel 5 mm;
  • Profile pipe 40×20 mm;
  • Paint and brush;
  • Bolts and screed.

Before you make a dump, it is necessary to calculate the correspondence of the power of the motor block sizes of the bucket. Excessive load leads to rapid wear of parts and mechanisms of the unit. Depending on the weight and power of the machine, the shovels are made 60-100 cm wide and 20-30 cm high.

Snow removal homemade homemade for a walk.Behind tractor with your own hands is made in the following sequence:

Adjustable-Rim Wheels for walk-behind tractors

  • Applying to a barrel of markings, sawing it into 3 identical parts vertically. Cutting 1 segment in strips 5 cm wide.
  • Fixing 2 blanks using bitumen and rivets. Alignment of the edges of the product. Reinforcement of the bucket with transverse racks.
  • Fixing the strips of tin along the edges of the shovel. This is done using welding or bolts.
  • Drilling holes for bolts. Joining the lower part of the bucket from the rubber.
  • Making coupling for a shovel. It is done by welding a piece of pipe and a semicircle of sheet metal to the dump to the dump. Holes are applied to the sector to adjust the angle of attack. To the bracket of the motor block, a homemade snowplower device is attached to the adapter from a profile pipe.

The finished product needs to be cleaned and painted. All bolt compounds must be regularly lubricated to prevent corrosion.

General device and types of jacks

This tool is usually used to raise the vehicle to replace the wheels. It is used both for professional repairs and for work at home. Thanks to the jack, you can carry out repair work in some compartments under the machine.

Every car owner has a jack

What is characteristic, the jack is popular not only in the automotive sphere. With its help, different designs are installed, some construction work is not complete without the tool, it is used in the repair of various equipment.

The design of the hydraulic jack

The jacks can be several types, we will get acquainted with them:

  • Mechanical. To rise in such devices, a lever on the handle is pressed. They are compact, do not require great physical efforts, but are used infrequently;
  • Hydraulic. Differ in the principle of operation: the machine rises due to the pressure that comes, created by the working fluid. A very popular variety;
  • Pneumatic. Work at the expense of compressed gases. There is a special camera that increases in size due to pressure and thereby raises the car.

Note! If you wish, you can make any of these jacks with your own hands without any problems, you need only suitable materials and tools. Consider step.By.Step instructions to create the simplest and most effective jacks.

Homemade variator for a walk.Behind tractor

The variator allows you to smoothly change the speed without sharp jerks, saves fuel, transmitting the torque. Engines from a walk.Behind tractor are often used as a generator to provide electricity for living rooms, adjacent territories, as well as for the operation of turning machines.

A homemade variator can be made in different ways, the easiest way is to use a ready.Made variator, which can be redone for a particular walk.Behind tractor. Another way is to use ready.Made parts from gearboxes and other mechanisms. Also, parts can be made independently, provided that special equipment is available (you need hot stamping for disks). Schemes and videos on creating details and assembling pulleys are easy to find on the Internet.

See also  How to make a grain grinder from an angle grinder

You can make a variator of the wheel hubs, the main thing is to make the hole diameter suitable for the crankshaft. In addition to pulleys for the variator, a belt is required, which is one of the most important details. The belt should be durable, and all the details of the variator must be regularly lubricated.

Types and comparative characteristics

Probably every good owner has a jack of tools. And who often has to raise goods, repair the car, change the wheels, know that, by safety, it is necessary to put several units of a lifting tool for insurance.

Of course, an ordinary solid item can be used as a spare option. For example, everyone is familiar with bricks laying. But such a artisan approach simply cannot inspire proper confidence. Therefore, sometimes you can approach the issue of security more thoroughly and make a homemade jack for the garage. Over, this work does not imply any special difficulties.

Each type of jack has its own advantages and disadvantages. Some easier in the device (therefore, it is easier to assemble them with your own hands), some are considered the most reliable and powerful.

The principle of working with a snowball for a walk.Behind tractor

As a rule, all motor cultivators have a standard bracket for attaching attachments. It is quite suitable for joining the frontal dump. If necessary, an adapter is made to ensure the possibility of turning the bucket to the right or to the left.

We offer to familiarize yourself with fertilizers from sawdust for tomatoes

The mount is made in this way:

  • A profile pipe is welded from the back of the bucket. To ensure the strength of fixation, it is advisable to duplicate the welds with several bolts.
  • A semicircle with a diameter of 20-25 cm from sheet metal with a thickness of 10 mm is cut. The workpiece is welded to the profile pipe. In it along the edge with an interval of 20 mm, holes are made to set the corner.
  • A holder in the form of the letter “G” is made from the square of the square section. The short side of the holder is fixed on the rotary sector, the second end is rigidly fixed on the bracket of the walk.Behind tractor. To adjust the height of the knife, bolts screwed into the adapter are used.

A simpler method of connection is the system of eye and clamps made of thick sheet steel.

Instead of a barrel, a gas cylinder will serve as a material for a shovel. The principle of manufacturing a hinged device for a single tractor is similar, but there are a number of nuances:

If there are gas residues in the cylinder, it is pulled by unscrewing the valve. However, no less dangerous condensation may still remain inside. The bronze valve is completely twisted with the key from the cylinder and, turning it over, drain the remaining liquid

Attention! Condensate from the cylinder is poisonous, fiery and has a caustic toxic smell. You need to think through a way of displaying fluid in advance.Thin plugs are cut off from the cylinder and dissolve it into two parts. Water is not poured into the cylinder a little to the top

Water is not poured into the cylinder a little to the top

Corner grinding is cut off the upper semicircular plug. Pour water, after which they cut off the lower plug. The bottom. The resulting pipe is cut along the corner grinder into two halves. Semicircular segments are welded together in length.

Usually the mass of the dump does not exceed 20 kg. You can hang it on any single tractor. Depending on the model of the unit, the connection of the hitch producer provides for the front or rear. In the second version, the steering column has the property of turning around 180 about.

Necessary tools

The main tools and materials will be required:

There should also be a roulette, a ruler and other measuring tools nearby. Additionally, it is recommended to prepare a marker so that you can mark measurements.

Pneumatic

This is a jack in the design of which a pneumatic pillow is provided. Making the tool will not take much time and effort. In addition, the drawing of the design of the unit is interesting, which will make the assembly of an unusual.

With the help of powerful jacks, accurate installation is performed, so the unit is popular in many areas. The shell has a flat shape, is the basis of the device. During operation, compressed air is supplied, ensuring an increase.

See also  How to make a bike with a chainsaw engine

To create a mechanism, you will need to prepare:

The procedure is carried out in several stages:

  • First, the pillow holes are mounted in the fastening bolts. Previously, each bolt is drilled.
  • Next, make a hole in the wheel bolts vase. It will be used as a valve.
  • The third stage implies the connection of all elements. The output is closed with a ball, the yaki will prevent the flow of air flows during the operation of the unit.
make, jack, walk, tractor

To use the devices, you need a pump. The unit should be placed under the bottom of the machine. Additionally, so that the device does not move off, you need to prepare a bar.

Homemade variator for a walk.Behind tractor

The variator allows you to smoothly change the speed without sharp jerks, saves fuel, transmitting the torque. Engines from a walk.Behind tractor are often used as a generator to provide electricity for living rooms, adjacent territories, as well as for the operation of turning machines.

A homemade variator can be made in different ways, the easiest way is to use a ready.Made variator, which can be redone for a particular walk.Behind tractor. Another way is to use ready.Made parts from gearboxes and other mechanisms. Also, parts can be made independently, provided that special equipment is available (you need hot stamping for disks). Schemes and videos on creating details and assembling pulleys are easy to find on the Internet.

You can make a variator of the wheel hubs, the main thing is to make the hole diameter suitable for the crankshaft. In addition to pulleys for the variator, a belt is required, which is one of the most important details. The belt should be durable, and all the details of the variator must be regularly lubricated.

What are the motoblocks equip

The same tractor in itself represents only a power unit with wheels. So that he can do useful work, it must be turned into an agricultural machine, supplementing with attaching equipment. Only then do the positive aspects of this energy.Saturated device begin to appear.

A small list of basic attachments and nozzles:

  • Ground.Bearer will allow the walk.Behind tractor to move along arable land.
  • The plow and milling cutter. The deep cultivation of the land with the turnover of the layer has long been performed by plows. Soil milling is a device that can loosen the fertile layer.
  • Potato.Resident will facilitate the work of a rural resident and summer resident when planting potatoes.
  • Ploskorets is one of the ancient instruments that experiences a second birth with the emergence of ideas for organic (environmental) agriculture.
  • Helpers. Increasing the crop of root crops, as well as increasing the efficiency of the root system of plants is achieved by the use of cummers.
  • The trailer turns one.Axle tractor into a vehicle that can transport goods on the site and public roads.
  • The snowman expands the period of use of the walk.Behind tractor, in winter it is actively used to clear snow.

This is far from a complete list of hinged equipment for a walk.Behind tractor.

It is not necessary to purchase the entire set of attachments for the walk.Behind tractor at once. As necessary, additional tools are purchased or manufactured.

Do.It.Yourself soils

The torque of the engine through the transmission is transmitted to the wheels. To move on arable land, you need to create a sufficient effort. You can increase traction by increasing the coefficient of clutch of the wheel with soil. Therefore, the ceremonial.Bearing increases this coefficient several times, allowing you not to increase the mass of the power unit.

To make this attachment equipment, you need to purchase:

  • Sheet steel 2-3 mm thick, sufficiently steel of the usual quality of ST3;
  • An is an isolation corner of 35-50 mm;
  • A pipe with an inner diameter of more than 25 mm.

This set of workpieces is sufficient to start work. It remains to choose a design or develop your own.

The heater can be leading and invoice. Leading soil.Spaces are installed in the place of the base wheels of the walk.Behind engineer. Invoices are worn over the base wheel. Often make leading homemade soil.Spaces.

make, jack, walk, tractor

DIY plow and milling cutter

The plow with all its external simplicity is quite complicated in the manufacture. Usually, manufacturing begins with the coupling. Special attachment equipment. The hull is fixed on the hitch. This is the main working body. The motor.Block plow produces the soil layer. Then the layer is formed, and then its turnover occurs.

The design of the plow body includes several components:

  • A lot. Crashes into the soil;
  • Dumping. Serves to create a layer and revolution given to the movement;
  • Field board. Stabilizes the direction of the entire agricultural unit.
See also  How to trim a ceiling plinth without a joiner

For a walk.Behind tractor, the design of a swivel plow is interesting, with one movement of the plow lock, it easily changes from the right to the left and vice versa and vice versa. This is very convenient for cultivating land in small areas in length.

If the plow can be conditionally recognized as a passive working needle, then the soil milling cutter is active. When processing the soil, the wheels are removed, the movement of the unit occurs due to the rotation of the milling. Working blades make a rotational movement and loosen the ground.

For the manufacture of milling, strip rental is used with a thickness of 5 mm and more. To reduce the resistance during operation, the shoulder blades are pulled.

Do.It.Yourself potato

Potato.Resident mechanizes the work on sowing potatoes. This attaching equipment consists of:

make, jack, walk, tractor
  • Bunker, where the seed is concentrated;
  • A dispenser in the form of a drum rotating jointly by the wheels of a walk.Behind tractor, it captures the potatoes and directs them to the seed;
  • Sequin guiding seeds into the soil;
  • A looser creating a sowing furrow in the soil;
  • Disk cultivals completing the operation of sowing potatoes.

There are many different potato.Residential designs. Masters use the capacitors for the hopper they have, select options for manufacturing a dispenser using plywood. In separate soot, the air flow accelerates the movement of landing tubers into the soil. There are very simple designs, in them plywood discs replace several executive mechanisms for dosing and laying potatoes into a furrow at once. Many homemade authors invented original hinged units.

For the manufacture of potatoes for a walk.Behind engineer, you will need:

  • Thin leaf galvanized steel;
  • Profile pipes for the formation of a hinged equipment body;
  • Strip steel 4-5 mm thick;
  • Small format.

DIY flat lock

Cut off the rhizomes of weeds, loosen the soil to a small depth without turning the layer such nozzles as flat cutters. A flat cutter for a walk.Behind tractor is quite simple to manufacture. For him you will need:

The procedure for manufacturing this home.Made attachment equipment:

The BCS Walk-Behind Tractor

  • A rack is cut out of a thick sheet on a template. Fastenous holes are drilled on the rack.
  • A spark cutter is cut out of the thin sheet. According to the template, the anvil is flexion of the paw according to the drawing. The plane cutter element is assembled using rivets or welded into a single node.
  • Harvesting of the frame for fixing the working body are cut out from the profile pipe. The scheme of lifting and lowering the frame is worked out. Next, the hitch is welded, on which the elements of the plane cutters will be installed in the future.
  • The attachment scheme is made to the mounting equipment to the walk.Behind tractor. The data obtained is transferred to the frame. Plates are made for fixing the clutch. The performance of the rise and lowering is checked. All products are painted using soil-enamel 2 in 1 to protect against corrosion.

Awesome equipment is tested in the field. If necessary, adjustments are made to improve indicators.

make, jack, walk, tractor

What to add?

It is interesting that many owners of motoblocks who want to redo the existing equipment into an all.Terrain vehicle set the following task: the device should easily transform from a country assistant into a highly spent vehicle and vice versa and vice versa. That is, in the shortest possible time, an all.Terrain vehicle for a trip, for example, fishing should be obtained from the walk.Behind tractor.

The goal is reasonable, because to lose agricultural functionality of equipment in order to be able to go 3-4 times a month to the forest or to the lake is not very reasonable.

Immediately note that the goals: get a transformer, you can achieve quite easily. The key to achieving the goal is the following rule: Changes in the design should be minimal.

In fact, to solve the problem described, you need to add a frame with cardans to the walk.Behind tractor, having removed the wheels and the control body. Other improvements can be carried out, but this is already at will.

| Denial of responsibility | Contacts |RSS