How to make a lawn mower out of a corner grinder. Video about one of the options for the lawn mower from the washing machine

Trimmer for grass from corner grinder with your own hands

All owners of personal plots are faced with the problem of mowing grass, which grows literally before our eyes, and during the season it is required to ennoble their site several times. The usual manual spit has been replaced by benzotrimers and electrimmers for a long time.

But the price of them does not decrease and is quite noticeable for many owners of cottages and private houses.

People’s craftsmen still found a way out of this situation and learned to make trimmers for grass with their own hands literally from improvised means, using benzo- and power tools not intended for these purposes.

make, lawn, mower, corner, grinder

Trimmer for grass from corner grinder

We will see how to make a trimmer for grass from a corner grinder with your own hands, work order:

  • First prepare a bracket. It is created to gently gently the corner grinder body. The iron plate is applied to the body and bend.
  • There are threaded holes from the 2nd sides of the body, in which the transping hand is attached. They attach a trimmer for the grass to them.
  • In the bracket from the 2nd sides, the holes are drilled with such a macar so that they correspond to the gaps located on the tool body. For accuracy, the details make notes with a marker, clamp it with a vice and drill.
  • Then the guide is attached to the bracket. Its size should correspond to the length of the case or be slightly shorter. The guide is attached by the welding machine, the remains of the scale are knocked down. The part is polished with a metal brush.
  • A handle (bar) is made from the iron pipe). To fix the handle under the slope, the tip of the pipe is cut under the beard. The finished handle is welded to the structure, the scale is knocked down and the part is cleaned with a brush.
  • To attach the tool, it is necessary to unscrew the protective disk of the corner grinder.
  • Then the homemade is installed on the wheels. To do this, you can borrow wheels from a cart or a baby stroller with brackets.
  • First mount the corner grinder, then a wheel with a bracket. Everything is fixed with a bolt. On the other hand, they make the same fasteners.
  • The cutting node is made from the iron cable. A kapron wire created for trimmers is suitable. It is threaded through a clamping nut and a key hole according to the cross-to-cross method. Then the nut is twisted together with the cables.
  • The wire is fixed with island.

For safety precautions, it is recommended to make a protective device for the device. A corner grinder cover is made of duralumin sheet or narrow tin.

Lawn mowed on wheels from battery.End corner grinders

Another version of a corner grinder mowel is a manual portable trimmer for herbs on wheels, which can trim the lawn in the most inaccessible places.

What materials for manufacturing will be needed:

  • Pan or a small cylinder from the freon;
  • Steel sheet;
  • 4 wheels, bearings and axes;
  • A segment of a metal pipe with a round section;
  • A piece of thick carbon steel for the manufacture of a knife.
  • Corner grinder with nozzles for cutting metal and grinding;
  • Welding machine;
  • Drill with a crown for metal;
  • Optional, but desirable. A lathe and a tape grinding machine, a spray can;
  • Marker and roulette.

DIY mowel manufacturing process:

  • To make the case, from an empty gas cylinder you need to cut off the upper or lower part. Finding the center of the convex bottom, cut it with a corner grinder and weld a flat piece of sheet steel.
  • The next step is to make a clamp (one or two) for fastening the corner grinder to the body. It can be made from a piece of pipe or thick steel. Make a hole in the center of the body along the diameter of the clamp and weld it.
  • Make a pipe for the removal of mowed grass: drill a hole in the housing and weld the knee from the pipe so that the grass does not fly on you during work.
  • Knock for the future trimmer for grass cut and sharpen. To weld a long nut to the center of the workpiece. So that the grass does not wind on the axis, you can weld a piece of the pipe above the axis, and the end of the end to brew and drill a hole under the nut.
  • Next, prepare the axes for the wheels: drill them along, cut the threads for the screws and fasten the wheels. Process ready.Made axes to a metal case, if necessary, make steel shields for reliability of fastening.
  • The final stage is painting and assembly of the structure. You can start work.

How to make a trimmer for grass from a corner grinder with your own hands

The first thing to do is the bracket for girth of the corner grinder. To do this, take a steel plate and bend on both sides on the body. I took the plate already bent on one side initially. Now I can only bent the second edge.

I put an angular grinder to the body. Marker I notice the place of bending.

Next, clamp in a vice and bend the hammer blows. I saw off the excess with the same corner grinder.

In the case of the tool on both sides there are holes with thread. A handle is screwed into these holes to cut both on the left side and on the right, the handle is made of a transit. That’s just for these holes and the trimmer bracket will be fixed for the grass. On the sides of the bracket, it is necessary to drill holes so that they coincide with holes on the sides of the tool. We notice a marker.

Next, in the bracket, you need to attach the corner grinder guide along the length of the case or shorter.

We weld welding. Knock down the scale and clean the metal brush.

Now the barbell. It will be made from a steel pipe. At the end of the pipe we will make a beard so that the handle is attached at an angle. Mark the fishing line for the trimmer cut.

We weld welding. Also knock down the ward with a hammer, clean the metal brush.

Now it’s time to install the corner grinder itself in the seat. To do this, we unscrew the protective circle.

So that the trimmer for the grass does not touch the ground and be at a certain distance, the wheels will be attached to it. They can be taken from an old and unnecessary baby stroller or any other cart. In extreme cases, make it yourself from wooden round. I had the wheels with the brackets.

We attach a wheel with a bracket and fix it all with a bolt. We tighten well with the key. We do the same procedure from the opposite side.

The finished trimmer for the grass for the mowing of the grass is almost ready.

It remains to make a cutting. To do this, take segments of a steel cable or a specialized nylon wire for trimmers. We stretch the cross on the clip through the clamping nut, through the key holes.

Score a nut with cutting cables on a corner grinder.

You need to get a long extension cord and you can mow.

Before finishing, I would like to say that the corner grinder is not intended for such work. And if you want to repeat this homemade, then take the fully responsibility and use everything at your own peril and risk. With mowing grass, be very careful, steel cable rotating at high speeds is very dangerous. All manipulations for the installation or dismantling of the cutting part do only when the fork is pulled out of the outlet. And so the device is necessary and it may well get used to cut the lawn in front of the house.

Block: 2/3 | Summer characters: 2687

Necessary tools and materials

To make a lawn mower made of corner grinder or washing machine at home, you will need to stock up on the following tools, devices and additional materials:

  • Electric drill;
  • Corner grinding with disks for metal or an electrician with files according to different materials;
  • Hammer;
  • Roulette or ruler;
  • Pencil or marker;
  • Vise;
  • Pliers;
  • Screwdriver;
  • As an abrasive stone or an emery machine;
  • Welding apparatus and electrodes to it (if you make welded metal connections, not bolted);
  • Wires;
  • Button on/disconnection (taken from an angular grinder or washing machine);
  • Bolts with nuts and washers (preferably grover);
  • Metal corners or wooden bars.

Instead of a corner grinder or electrolobian, you can use a hand hacksaw for metal or wood saw with small teeth. It is also recommended to make a drawing of a home.Made mechanism in order to have an idea of ​​the final result, based on the details available at the disposal.

How to mow grass with a corner grinder

What only skillful hands and restless heads did not do with the power tool from the moment of its appearance in the world. Here, we take a simple angular grinding machine called the people with a “corner grinder”. And the end saw was made from it, and it was difficult to snow, but they removed, well, a lot of alternative applications found the population of our country to this instrument.

Sharpening Lawnmower Blades (unboxing and using a cordless 20v Bauer angle grinder)

Corner grinder at work. Today we will look at one of the examples of how, with the help of this tool, we can restore order in the garden or on the lawn of a summer house or other possession. First, take a piece of the steel strip, measure and bend the rectangular bracket from it, so that we will subsequently put it on the gearbox body.

We make a bracket.After that, you need to mark and drill a pair of holes on the bracket in those places where there are holes for the handle on the body of the same gearbox. In this case, the diameter of the holes should be no less than the diameter of the holes for the hilt.

We make a couple of holes. Then, take the rest of the strip and weld it perpendicular to the bracket. It will serve us with an additional mount and an element of strengthening the design itself. It turns out a kind of frame.

Cook a piece across. To the frame at an angle of fifty degrees, we weld a piece of steel water pipe. She will serve us with a pen and cable suspension.

We weld the pipe.We are going further, and we are close to the finale. We find in our own or neighboring section a long.Abandoned, but carefully preserved side wheels from a children’s bicycle. We put on the bracket on the corner grinder, and fasten the wheels and the bracket to the body through.

Collect the device in one. The point remains for a trifle. We stretch a couple of pieces of cable into the key holes on the clamping nut, and fasten it to your place. We fix the wire to the handle along the entire length.

The new lawn mower is ready.We include in a socket, launch a corner grinding and its mowing grass on the surface. Such a simple and cheap braid for the grass will be very useful when opening a new summer season.

We put things in order on the site. Source

How to make a lawn mower with your own hands

You can make a lawn mower with a gasoline or electric engine. Gasoline is used for large areas, they are not tied to electric power. In small summer cottages with a small volume of work, electrical devices are used. The unit consists of the following elements:

The engine is mounted on the platform, the cutter is under it. The handle and lever are attached to the platform itself. Self.Propelled homemade haymaking will keep the lawn in excellent condition.

From the washing machine

A home master, if desired, can create a lawn mower with your own hands from a washing machine. Inexpensive lawn mower from the washing machine includes the following details:

  • Engine from the washing machine;
  • Steel knives;
  • Wheels from the cart;
  • Pipe for the handle;
  • Electrical wir;
  • Switch;
  • Fork.

For the manufacture of homemade, you can use an 180 watts motor with a condenser and launch relay. This motor is taken from the washing machine. It is worth picking up or making wheels from plywood. They need to be placed at a distance of 5-6 cm from the surface of the soil.

This distance is the height of the mowing of grass. The number of wheels is 4, 3, 2. The sheet should have dimensions 30×50 cm. Knives are made of steel with a width of 20-50 mm, 2-3 mm thick. The cutting side bends slightly down, this will protect the shaft from garbage and grass. The pen is made by bending the pipe to make it convenient to support the unit. The handle is attached to the frame with welding.

A platform made of sheet is installed on the chassis from the cart. The handle is made from the pipes and fixed to the platform with welding. Make a hole for a motor shaft. In front of the frames weld a protective grille of steel. The top and bottom of the lattice are screwed with screws, and wire is welded to them.

Electric lawnies grate provides a knife gap for a knife. The engine is fixed on the platform, its shaft must go into a cut hole. A cut with sharpened teeth is put on the shaft. A hole is drilled in the middle.

The knife must be balanced and specify. The engine is covered with a casing to protect it from grass. Since the engine must cool during operation, holes are provided in the casing. Now the wiring is attached to the motor and fix it. The metal handle must be wrapped with a rubber casing to protect against electricity. You can also additionally make a travic collector for the lawn mower with your own hands.

From corner grinders

A cheap lawn mower made of corner grinder with your own hands is created as follows. The device case is made from the car disk. Cut the disk into 2 parts. The lid is welded to one part.

Then, in the side of the disk, the opening is created, where it will be in front of the mower. Fixed on the wheel housing and handle. In the casing of the corner grinder or trimmer for grass, the holes are made. The device is fixed on the housing of the lawn mower using screws. The knife can be made of steel. Its edges are hidden on a sharpener and unfolded in the form of a propeller.

The cutting element is attached to the shaft of the corner grinder. A nut is wound on it. The cutting device is screwed with a bolt fixed into the nut. The switch on the corner grinder is fixed with a wooden bar. A switch and a fork are installed on the mowing handle so that you can connect an extension cord.

From the vacuum cleaner

Inexpensive home.Made lawn mower from a vacuum cleaner is made as follows. From the old vacuum cleaner, you can remove the electric motor and apply it to create a homemade.

  • Electric motor from the Soviet vacuum cleaner Buran with a capacity of 300 watts.
  • A textolite plate with 260×180 mm dimensions, which is used as a support for the engine.
  • Wheels from the cart.
  • Chassis.
  • Pipe.
  • Switch.
  • A tin sheet for the performance of the casings that will protect the motor from dirt.
  • A steel corner from which a frame is made.
  • Electric wire.

You should prepare tools for work:

  • Welding machine;
  • Angle Grinder;
  • Drill;
  • Wrench;
  • Eletrolobzik;
  • Soldering iron;
  • Screwdriver;
  • Roulette;
  • Marker.

Create a cutter for a home.Made mowing of grass. In factory devices, it is made from a strong polymer thread. You need to buy it and attach it to the steel segment with the hole available in the middle. Then make a knife from a saw. Solid steel soften.

To make a mower, the workpiece is heated to a high temperature and let it cool. When the knife is made, it must be heated again and quickly cool. The length of the cutter is about 30-50 cm. The cutting part should be sharpened at an angle of 60º. The edges are installed along the edges of the knife. The shaft opening should be precise, t. To. Cars need to be balanced.

The motor rotates at a speed of 11000-30000 rpm, while the imbalance can cause vibration.

make, lawn, mower, corner, grinder

All details should be perfectly fixed. So that the cutter is not damaged about the stones, it is performed by the team: to the central basis, they are attached with bolts on both sides of steel knives. When hitting the stones, the knife will turn and will not be able to be damaged.

A hole is made in the plate so that you can install the engine from the vacuum cleaner there there. The engine is placed in a slot and pressed with a steel strip, which is mounted across the slots and screwed with bolts. A plot with a turbine is separated from the motor, instead of which a cutting element is installed on the shaft.

On the other hand, the turbine is removed and a fan of tin is put instead of it. To protect the engine from grass and dusting, tin casing is attached to the plate. You can use the cover from the vacuum cleaner from which the motor was taken. Attach a textolite plate with an engine on a chassis with wheels.

Then, a handle is attached to a home.Made haying mushroom with the help of brackets, on which the switch is fixed. After that, attach to the motor and the wire button, isolate them and carry out a test start. If there are metal parts in the device, ground is attached to them.

From a drill

Another way is to make a mower from an electric drill. The main components of the electric coslinks are performed on milling, turning machines. At first, a supporting element must be performed on a lathe on a lathe. The neck of the drill should have the same diameter.

How to make a lawn mower with your own hands

You can make a lawn mower with a gasoline or electric engine. Gasoline is used for large areas, they are not tied to electric power. In small summer cottages with a small volume of work, electrical devices are used. The unit consists of the following elements:

The engine is mounted on the platform, the cutter is under it. The handle and lever are attached to the platform itself. Self.Propelled homemade haymaking will keep the lawn in excellent condition.

From the washing machine

A home master, if desired, can create a lawn mower with your own hands from a washing machine. Inexpensive lawn mower from the washing machine includes the following details:

  • Engine from the washing machine;
  • Steel knives;
  • Wheels from the cart;
  • Pipe for the handle;
  • Electrical wir;
  • Switch;
  • Fork.

For the manufacture of homemade, you can use an 180 watts motor with a condenser and launch relay. This motor is taken from the washing machine. It is worth picking up or making wheels from plywood. They need to be placed at a distance of 5-6 cm from the surface of the soil.

This distance is the height of the mowing of grass. The number of wheels is 4, 3, 2. The sheet should have dimensions 30×50 cm. Knives are made of steel with a width of 20-50 mm, 2-3 mm thick. The cutting side bends slightly down, this will protect the shaft from garbage and grass. The pen is made by bending the pipe to make it convenient to support the unit. The handle is attached to the frame with welding.

A platform made of sheet is installed on the chassis from the cart. The handle is made from the pipes and fixed to the platform with welding. Make a hole for a motor shaft. In front of the frames weld a protective grille of steel. The top and bottom of the lattice are screwed with screws, and wire is welded to them.

Electric lawnies grate provides a knife gap for a knife. The engine is fixed on the platform, its shaft must go into a cut hole. A cut with sharpened teeth is put on the shaft. A hole is drilled in the middle.

The knife must be balanced and specify. The engine is covered with a casing to protect it from grass. Since the engine must cool during operation, holes are provided in the casing. Now the wiring is attached to the motor and fix it. The metal handle must be wrapped with a rubber casing to protect against electricity. You can also additionally make a travic collector for the lawn mower with your own hands.

From corner grinders

A cheap lawn mower made of corner grinder with your own hands is created as follows. The device case is made from the car disk. Cut the disk into 2 parts. The lid is welded to one part.

Then, in the side of the disk, the opening is created, where it will be in front of the mower. Fixed on the wheel housing and handle. In the casing of the corner grinder or trimmer for grass, the holes are made. The device is fixed on the housing of the lawn mower using screws. The knife can be made of steel. Its edges are hidden on a sharpener and unfolded in the form of a propeller.

The cutting element is attached to the shaft of the corner grinder. A nut is wound on it. The cutting device is screwed with a bolt fixed into the nut. The switch on the corner grinder is fixed with a wooden bar. A switch and a fork are installed on the mowing handle so that you can connect an extension cord.

Homemade Mower Blade Sharpner and Shop Projects Update

From the vacuum cleaner

Inexpensive home.Made lawn mower from a vacuum cleaner is made as follows. From the old vacuum cleaner, you can remove the electric motor and apply it to create a homemade.

  • Electric motor from the Soviet vacuum cleaner Buran with a capacity of 300 watts.
  • A textolite plate with 260×180 mm dimensions, which is used as a support for the engine.
  • Wheels from the cart.
  • Chassis.
  • Pipe.
  • Switch.
  • A tin sheet for the performance of the casings that will protect the motor from dirt.
  • A steel corner from which a frame is made.
  • Electric wire.

You should prepare tools for work:

  • Welding machine;
  • Angle Grinder;
  • Drill;
  • Wrench;
  • Eletrolobzik;
  • Soldering iron;
  • Screwdriver;
  • Roulette;
  • Marker.

Create a cutter for a home.Made mowing of grass. In factory devices, it is made from a strong polymer thread. You need to buy it and attach it to the steel segment with the hole available in the middle. Then make a knife from a saw. Solid steel soften.

To make a mower, the workpiece is heated to a high temperature and let it cool. When the knife is made, it must be heated again and quickly cool. The length of the cutter is about 30-50 cm. The cutting part should be sharpened at an angle of 60º. The edges are installed along the edges of the knife. The shaft opening should be precise, t. To. Cars need to be balanced.

The motor rotates at a speed of 11000-30000 rpm, while the imbalance can cause vibration.

All details should be perfectly fixed. So that the cutter is not damaged about the stones, it is carried out by the prefabricated: to the central basis, they are attached with bolts on both sides of steel knives. When hitting the stones, the knife will turn and will not be able to be damaged.

A hole is made in the plate so that you can install the engine from the vacuum cleaner there there. The engine is placed in a slot and pressed with a steel strip, which is mounted across the slots and screwed with bolts. A plot with a turbine is separated from the motor, instead of which a cutting element is installed on the shaft.

On the other hand, the turbine is removed and a fan of tin is put instead of it. To protect the engine from grass and dusting, tin casing is attached to the plate. You can use the cover from the vacuum cleaner from which the motor was taken. Attach a textolite plate with an engine on a chassis with wheels.

Then, a handle is attached to a home.Made haying mushroom with the help of brackets, on which the switch is fixed. After that, attach to the motor and the wire button, isolate them and carry out a test start. If there are metal parts in the device, ground is attached to them.

From a drill

Another way is to make a mower from an electric drill. The main components of the electric coslinks are performed on milling, turning machines. At first, a supporting element must be performed on a lathe on a lathe. The neck of the drill should have the same diameter.

Power for a trimmer for grass

For more comfortable work with a trimmer, if it is understood to process a large area overgrown with grass, it is advisable to use a special belt. This device relieves fatigue from the hands and back of the mowing operator and greatly facilitates the process when compared with the same work, but without a belt.

Belts are shoulder and ranger. The shoulder belt is the simplest device and consists of a loop with two or one latch (carabiner), with which it is attached to a mowing unit. A plastic plate is usually attached to the second carbine, which protects the side of the operator from pressure with a bar trimmer for grass.

Shoulder belt is usually used with light trimmers weighing 3-4 kg. For heavier units, it is more convenient to use a parapier belt.

make, lawn, mower, corner, grinder

A belt for a trimmer for grass can be easily ordered via the Internet or buy in a specialized store where these devices and components are sold to them.

And higher.

make, lawn, mower, corner, grinder

If there is a desire to do it with her own hands, then any mistress, looking at this device, can easily sew it from improvised means (old belts and belts). You may have to buy buckles and carbines. But still, we recommend buying a ready.Made ran.Out suspension and not waste time and money to make the worst quality than ready.Made devices.

| Denial of responsibility | Contacts |RSS