How to make a mixer from a drill. Production of a blender

DIY forced concrete mixer: step.By.Step instructions and drawings

It is difficult to even imagine any construction without technological processes using cement solutions. And for the owners of their own country house, with their constant state of “permanent” repair and improvement of the territory, concreting is generally a very popular operation. Then the garden paths must be poured, then the foundation for the gazebo, then the blind area, then put the fence in a word, literally on each one The step is required to make concrete. The difference is only in the scale of the event.

Many individual builders prefer do not fool around with independent kneading the solution. This can be avoided if there is a concrete plant or another enterprise that provides concrete manufacturing services and its delivery to the place of work. But, firstly, it costs a lot of money. Secondly, not everywhere such an opportunity is present. And, thirdly, there is far from always the meaning of SL to be to such services for considerations of a small scale of a construction or repair task-it will be either just funny or extremely unprofitable. Easier. Make the right amount of solution yourself. This, of course, can be done manually, but it is better to purchase (rent) a concrete mixer or show yourself a real owner: to make a concrete mixer for the future with your own hands.

The article will consider several models of homemade concrete mixers. From the simplest to those that are already not much different from the samples presented in stores.

Homemade kitchen mixer

Capacity and drive

It’s time to start action. Start with a glass in which you need to make a small hole. To do this, heat the metal end of the screwdriver using matches or lighter, then make a hole with a heated tip directly in the center of the bottom of the glass.

Next, we place a motor in the center of the glass and circle the marker of its edge, marking in the way where it will be located. While the engine is cleaned and the manipulations with a glass continues. That is, it is clear that the Mixer corps is gathering first of all.

Now you need to cut the hole with a clerical knife on the bottom of the glass on the lines intended by the marker, in which the motor will be placed. The engine should sit tightly in the hole, and not fall out of it, so the size of the hole should be slightly smaller than the motor.

Such a motor will be more than enough

Nutrition and communication

Now you need to prepare a place for a switch and wiring. If the power supply has two wires, then one is attached to the switch, and the other to the motor. Then the switch and gearbox are interconnected using a piece of copper wire.

Thus, a peculiar body of the mixer is obtained. In order not to worry that the design will fall apart, you can fix the motor and switch superglue.

We go to the second step. A tin is needed for the manufacture of a screw. To do this, a thin piece cut off from the can, put in a ring, the second one must wrap the resulting ring in the middle, so that the result is a figure resembling a butterfly. We received a screw, now we put a silicone nozzle on it, which will be worn on the pin.

While the tin is laid aside until the glue dries. We return again to the body with the motor. Put the glass cut side down. Here you need a second glass in which a hole has already been made using a screwdriver in advance. It needs to be installed on top of the motor. The result is a design in the form of a glass on a stand. In the center of the glass, a pin glued to the motor is placed, approximately a centimeter length.

During this time, the glue on the screw was to dry completely. We attach it to the pin. Ready, now you can try. Put the necessary ingredients in a glass with a screw, cover with a plastic lid for mixing without spray, and turn on the mixer.

make, mixer, drill, blender

Connecting equipment to control through pedal

It is not always convenient to choose and manually control the speed of new equipment. You can supplement the grinding machine with the pedal as follows:

However, you need to know that not every model is suitable for connecting to a new device. Incorrectly selected equipment will lead to overheating of the engine and its failure. All this can end with a short circuit. Calculating the required power is easy, on each product there is a shortcut indicating the nominal parameters.

To calculate the optimal pedal load, it is necessary to divide the power of the mixer engine into voltage in the network. In our case, this is:

If the pedal has a nominal load of the load above 3 amperes, such a connection is quite realistic.

This device is suitable for sharpening household knives, knives for a meat grinder, home tools, can be used for polishing wooden, plastic or metal objects.

Figure 4 engine control using the pedal frees hands

I turn blender motor into 220v electric generator

make, mixer, drill, blender

The principle of action and features of use

Depending on the principle of action, three types of tools are distinguished:

An ordinary electric drill mixer is a low-speed mechanisms of an unstressed type. The power of this tool ranges from 500 to 2000 watts, there are 2 comfortable handles, a rather large cartridge with a diameter of up to 16 mm.

Two.Handed models are divided into options with a single whisk or with two, the difference follows from the name: mechanisms with two whistles are mixed even by the most viscous mixture, they are equipped with a rather powerful gearbox and easily cope with solutions of various consistency. From light to concrete.

Nozzles for a construction mixer: forms and sizes

The nozzle for an electric construction mixer is a bar, from one end of which there is a corolla for mixing, and with the other a shank for attaching the nozzle to the drive. After you have decided on the composition of the mixture that you need to mix, you can choose the shape of the corolla. And the standard of the tail of the nozzle must comply with your power tool.

Varieties of shanks in nozzles for a mixer

Now on sale there are a large number of nozzles on a mixer with shanks of various shapes:

  • Ordinary hexagon, size 8, 9 or 10 mm. Such devices are designed for use in a power tool that has a regular fist clamp cartridge.
  • Hexagon (8, 10 or 12 mm) with a groove for spring mount in HEX cartridges (they can also be used in a power tool with a conventional clamping cartridge).
  • Thread M12, M14 and 21×1.5. Devices with such shanks can only be used in highly specialized mixers.
  • Sights designed for installation in SDS-PLUS cartridges (can also be used in a simple peorator).

The dimensions and shape of the corkscrew corps for the mixer

  • Standard length 400 and 600 mm (for some, extension cords are 400 mm. The total length up to 1 m).
  • The diameter of the corolla (part designed for mixing) from 80 to 220 mm.

The shape of the corolla is chosen depending on the mixture that has to be mixed. The main forms of corolla:

  • Spiral. Such corolla is divided into right.Handed ones, in which the spiral is twisted clockwise, and left.Handed, in which the spiral is twisted counterclockwise. Right-sided corolla in the process of mixing lift the solution from the bottom up and are designed for heavy or thick mixtures (concrete, sand-gravel, bitumen). Left.Sided spirals, on the contrary, capture the mixture from above when mixed and lower down. They are designed to mix various paints and varnishes, various fluid mixtures and liquid putty, since during their use there is no spraying.

On a note! If the construction mixer is equipped with a reverse system that provides the rotation of the corolla both clockwise and counterclockwise, then for various compounds of the mixture you can use only one nozzle (right.Hand or left.Handed).

  • Vennings with straight blades. Mixing occurs only in a horizontal plane, which prevents the capture of air and it enters the mixture. Suitable for mixing various compounds based on gypsum (air hit is extremely undesirable), mixtures for bulk floors and the like.
  • Rifle.Shaped corrugations (the screw is usually made of plastic). Mostly used for light liquid compounds of the mixture. Sometimes two screws are installed on the axis: the lower one, which lifts the components up, and the upper one, which prevents the spraying of the mixture.

Important! In the technical description, manufacturers indicate for mixing which type of mixture a specific whisk is intended, as well as the maximum recommended amount of the solution for which it is designed.

Depending on the size, materials and purpose

Simple homemade paint for paint

Hello to all home.Handers and home masters!

In my homemade creativity, I constantly have to deal with painting products with various colors, stains, varnishes, etc.P. In addition, the farm often has to carry out minor repairs associated with painting various surfaces (mainly wooden).

The paints for this, as a rule, do not need very much, so the most popular containers that I use are banks with a volume of 1-2 liters, no more.

Naturally, before using any paint, impregnation or varnish, you need to mix thoroughly, or even add a solvent or white spiteration, for a more liquid consistency.

Previously, I usually mixed the paint manually, but recently, I decided to still make a simple meshist for this purpose from a single piece of strong steel wire.

Model rating

The greatest popularity of consumers are the mixers of the following brands.

  • Fiolent is a Russian.Made product that is optimal for stirring the most thick and viscous compositions. The power of the device is 1100 watts, and the speed of 600 rpm.
  • Rebir. Under this brand the most popular low.Speed drills are produced. Separate models of this manufacturer have exceptional work characteristics: power up to 2000 watts and rotation speed. Up to 500 rpm.

Homemade kitchen mixer

It is possible to make a mini mixer yourself. This will need:

  • First of all, you need to get a motor. It should be powerful enough to cope with egg protein, we will not talk about products with a harder consistency yet. A suitable motor can be removed from the old cassette player for example.
  • Tin. Everything is simpler here, you can cut off a piece from a can from under any drink.
  • Plastic cover from the jar.
  • A pair of plastic cups.
  • You will also need a switch.
  • The power supply is selected depending on the power of the motor.
  • And of course, all this will be crazy with a conventional screwdriver.

Capacity and drive

It’s time to start action. Start with a glass in which you need to make a small hole. To do this, heat the metal end of the screwdriver using matches or lighter, then make a hole with a heated tip directly in the center of the bottom of the glass.

Next, we place a motor in the center of the glass and circle the marker of its edge, marking in the way where it will be located. While the engine is cleaned and the manipulations with a glass continues. That is, it is clear that the Mixer corps is gathering first of all.

Now you need to cut the hole with a clerical knife on the bottom of the glass on the lines intended by the marker, in which the motor will be placed. The engine should sit tightly in the hole, and not fall out of it, so the size of the hole should be slightly smaller than the motor.

Next, the height of the motor is measured. It will be necessary to leave the same height in the glass. For example, it turned out 5 cm, which means that we cut off all the excess using the same stationery knife.

Such a motor will be more than enough

Nutrition and communication

Now you need to prepare a place for a switch and wiring. If the power supply has two wires, then one is attached to the switch, and the other to the motor. Then the switch and gearbox are interconnected using a piece of copper wire.

Thus, a peculiar body of the mixer is obtained. In order not to worry that the design will fall apart, you can fix the motor and switch superglue.

We go to the second step. A tin is needed for the manufacture of a screw. To do this, a thin piece cut off from the can, put in a ring, the second one must wrap the resulting ring in the middle, so that the result is a figure resembling a butterfly. We received a screw, now we put a silicone nozzle on it, which will be worn on the pin.

While the tin is laid aside until the glue dries. We return again to the body with the motor. Put the glass cut side down. Here you need a second glass in which a hole has already been made using a screwdriver in advance. It needs to be installed on top of the motor. The result is a design in the form of a glass on a stand. In the center of the glass, a pin glued to the motor is placed, approximately a centimeter length.

During this time, the glue on the screw was to dry completely. We attach it to the pin. Ready, now you can try. Put the necessary ingredients in a glass with a screw, cover with a plastic lid for mixing without spray, and turn on the mixer.

Recommended nozzles

We recommend a batch of 120×600 mm SDS from Startul and a whisk of 120×600 mm M14 from GEPARD.

make, mixer, drill, blender

Mixer 120×600 mm SDS Startul is a right-sided spiral and is suitable for drifts and peorators with a SDL-PLUS connector. The recommended batch speed is 600 rpm, the nozzle is used for all types of heavy and viscous mixtures (plaster, putty, resin, concrete, etc.

Vennese 120×600 mm M14 GEPARD has a shank M14 at a height and basket diameter of 105/120 mm. According to the configuration, this is a right.Sided spiral, the optimal rotation frequency during a knead of 600 revolutions per minute.

How to Make SuperPower 2000Watts Mixer Grinder at Home || Anything CRUSH in 1-Minute

In the end, we recommend that when choosing a mixer, pay special attention to the type of shank, since the error will lead to the fact that the corolla simply will not be on the peorator or drill.

| Denial of responsibility | Contacts |RSS