How to make a motorcycle from an electric screwdriver. Single -speed

Trimmer for grass from an electric screwdriver with your own hands

The question of how to make a trimmer for grass with your own hands is always relevant among owners of private houses with a small land plot. A neat and well.Groomed lawn near the house, it is not only beautiful, but also safe in terms of the absence of ticks on it.

About how to get rid of ticks in a summer cottage was described earlier, today the question will be considered. How to make a trimmer for grass with your own hands from the most improvised means for this.

Today on sale you can find various options for trimmers working both from electricity and from gasoline. However, there is no opportunity to buy a trimmer for grass, and in most, the case is not so needed.

The advantages of a home.Made trimmer for grass from a drill or corner grinder are that when you need to shake the lawn near the house, the trimmer for grass is easy to gather. With unnecessary, the drill or corner grinder from the trimmer for the grass is removed and used for their intended purpose.

How to make a trimmer for grass from a drill and corner grind

In order to make a trimmer for grass from a drill, a lot of materials and tools will not be needed. It will also not be necessary to disassemble the drill in order to make a hand trimmer from it for the grass with your own hands.

In addition, a battery of a drill can be a battery screwdriver, which can be connected to a car battery to increase the duration of the trimmer for grass.

Making a trimmer for grass from a drill with your own hands

The basic requirements for a homemade trimmer are primarily presented to its safety. The knife of a homemade trimmer for the grass is very acute, so the presence of a protective casing on a trimmer is a prerequisite.

The same is to the handle of a trimmer for the grass on which the drill will be recorded. The handle should be made of durable materials, of course, from wood, but it is better to use an aluminum pipe for these purposes.

In addition, working with a trimmer after its assembly should not only be as safe as possible, but also conveniently. Therefore, the holder of the trimmer for the grass should be adjusted to their height, maybe install an additional handle on it from the side, etc. D.

First, the handle of a trimmer for the grass is prepared, on which the drill should be fixed. For fixing the drill will need long bolts and metal clamps. Must necessarily be a drill power supply should be wrapped in a trimmer handle for grass. It is impossible for the wire to dangle and is a danger when it falls under the cutting element of the trimmer for the grass.

How to make a knife for a trimmer for grass: Materials

A homemade trimmer knife for grass is attached to the drill with a nut and a bolt, which is clamped in the cartridge. Be sure to not forget before this and install a protective casing on a trimmer for grass to ensure its own safety while mowing grass.

A trimmer knife for grass can be made of instrumental steel or other very durable material. You should know that the smaller the thickness of the trimmer for the grass is the thickness, the better it will cope with the harsh grass. The length of the trimmer knife for the grass depends primarily on the protective casing and the width of the capture of mowing grass. Most often the length of the trimmer knife for grass does not exceed 30 centimeters.

Trimmer for grass from corner grinder with your own hands

The question of how to make a trimmer for grass from a corner grinder with your own hands is solved in approximately the same way as the above manufacturing a trimmer for grass from a drill. There is only a small difference in the mounting of the corner grinder to the holder. A metal pipe can be selected as a handle for a trimmer for grass, to which you need to weld a plate with a hole for fixing the corner grinder with a bolt at the end.

Small changes touched a makeshift trimmer knife for grass. In the case of a corner grinder, here a knife is not in the form of a long rectangle. A homemade trimmer knife for grass from a corner grinder is made of concrete disk, with pre.Cut sharp faces, which are just designed for mowing grass.

The question of how to make a trimmer for grass from a drill or corner grinder is completely solved and the main thing is not to forget about safety precautions and carefully study this issue.

Only after that, you can safely take up the manufacture of a trimmer for the grass with your own hands.

How is a trimmer for grass

To make a trimmer for grass at home, you should first understand the principle of its operation and the design. In general, all manual mowers are classified into gasoline and electric. The first option is more convenient, because the user is not attached to the outlet, but electric engines from household appliances or tools are more often taken to manufacture a home.Made device.

The design of both types of manual travo.Shirts includes:

  • Engine (electric or gasoline). Is suitable from household instruments (electric screwdriver, drill, corner grinder), from the washing machine, as well as the chainsaw;
  • Tank. For a gasoline engine;
  • Starter. It is best used to use a simple button with a repayable mechanism;
  • The bar is whole of wood or a metal pipe (an aluminum pipe is perfect, since it is easier), you can also make a sectional structure that will allow the holder to be adjusted to the growth of different people;
  • Handle for ease of work on which the button is placed. It should have a convenient grip and is made of non.Valid material;
  • Knife or fishing line for trimmer. It is better to use knives, since a fishing line for a trimmer is torn faster;
  • Protective casing. Powerfully boiled from thin metal, cut out of a plastic bottle of large volume or use an old pan.

Advice! It is better to make a knife from instrumental steel, an old disk from a circular saw or a hacksaw. It can be whole or with a replaceable blade. The second option is more convenient, since with damage it will be enough just to change the edge.

However, it should be understood that factory structures are more difficult than homemade devices. And getting a complete analogue of a store trimmer for grass will not work. Below are recommendations for the assembly of a functional hand mowing from different equipment.

From the vacuum cleaner

The trimmer for grass from the engine from the vacuum cleaner is made according to the same principle as from the corner grinder. The motor must be fixed on the rod, and either knives or a plastic or metal disk in which the fishing line for the trimmer is fixed on the engine shaft. On top of the cutting tool is closed with a protective casing.

So that the dust and small particles of mowed grass do not fall into the engine removed from the vacuum cleaner, it can also be hidden in a plastic casing made of a sewer pipe, as shown in the next photo.

Since the engine in the vacuum cleaner is high.Cost, it needs to provide cooling. Therefore, it is recommended to insert a homemade disk with cut and curved blades under the washer, into which the fishing line is inserted, so that it plays the role of a fan that creates a vacuum. It is required so that the air is sucked through the hose from above and cool the motor.

In order to facilitate the load on the hands of the mowing operator, the unit can be installed on the site with wheels. In this case, something similar to the lawnical mower will be obtained.

To fix the fishing line, you can also use either a pulley with a suitable landing hole, or a plastic wheel from a cart.

make, electric, screwdriver, speed

Wind generator from the working engine of an electric screwdriver.

What can be done from an old electric screwdriver? An excellent solution for lighting a summer cottage can be a windbreaker from an electric screwdriver engine. We will analyze the case and pull out all the electronics. Sold the diode bridge to the engine contacts. We fasten the blades to the cartridge. Consumer load is not more than 12 watts.

The more the length of the blades, the greater the power will give out the generator.

Alteration of an electric screwdriver in a trimmer for grass or a lawn mower

To make an electric costs with your own hands, such details and materials will be required:

  • A piece of plastic pipe about 2 m long;
  • Solder with a set for soldering;
  • Fasteners: screws, bolts with nuts;
  • 45 degrees a plastic corner;
  • A plug on the pipe;
  • 12 V motor from the electric shurubrust and the battery from it;
  • The wire;
  • Adapter from 40 to 50 mm for plastic pipes;
  • Power button;
  • A plastic bucket;
  • Contact clamps (crocodiles). 2 pcs;
  • Chancellery blades.

Attach 2 screws to the electric motor;

Install an electric motor, sticking its wiring in the pipe;

Mark the place of location of the future switch on the tube by marker;

Connect to the wiring switch, mount it;

Contact clamps are attached to the ends of the outlet wires to quickly connect to the battery;

A battery is made from the adapter;

Connect the drive, connect the adapter to the tube;

Using a conventional clamp for terminals, the nozzle is connected to the motor shaft;

make, electric, screwdriver, speed

A protective casing is made from a plastic bucket;

Check the performance of the design.

The created device will mow only herbal cover with soft stems. There are many various options for lawn mowers on the basis of network models. The photographs below show two homemade.

First, the base is created from metal, plywood or other materials, to which the wheels are then attached, as well as the control handle. With clamps or to the rack fix electric shuruvret. A cutting nozzle is inserted into the cartridge. To protect the legs from flying grass, the casing is attached to the back of the base. Food is done through the button or directly from the network.

Garden grinder

Using a drill, you can make a grinder for fine wooden debris, for example, branches or chips, the diameter of which does not exceed 10 mm, as well as for grass. In order to assemble such a homemade from an electric screwdriver or drill with your own hands, you will need:

The World’s Fastest ONYX Electric Bike. DIY 105 Volts Battery

  • Electric screwdriver or drill with a power of up to 0.5 kW;
  • Carvings shaft, which will fit into the cartridge;
  • Blades (for example, a canvas from a hacksaw);
  • A large bucket, a pan or a lump as a container for branches, it should not be made of plastic.

To make a garden chopper from an electric screwdriver required:

  • Drill the hole of the desired diameter in the center of the selected container for the shaft.
  • Place the container on the work surface. To do this, it can be fixed on the edge of the table or build a special frame from a metal corner.
  • Fix the knives on the shaft of the machine with bolts and washers (for the best work of the blade, it is recommended to install sharpening down);
  • To fix a drill or electric screwdriver under the bottom of the container so that the hole of the cartridge coincides with the shaft, and the electrical appliance itself does not begin to spin around its axis during operation.
  • Make a neckline 10×20 cm and insert a sleeve of plastic or metal into it to remove processed debris from the container.

Trimmer boat from a trimmer for grass. How to do it with your own hands, instructions for remaking

Every fisherman conceived about the replacement of the store for the boat with an alternative engine. It was learned to create from lawnmands, benzos, and even screwdrivers, since their cost is several times lower than the price of a finished sample. The most suitable option is a trimmer for grass, since this device is equipped with all the necessary elements and mechanisms.

Advantages of using a trimmer for grass

Using a trimmer for grass to create a boat engine has a number of advantages:

  • Much cheaper than a finished motor for the boat;
  • Minimum fuel consumption;
  • Low weight;
  • Reliability;
  • Tightness of the structure;
  • The presence of ready.Made elements for control;
  • Built.In tank and t.D.

Thanks to these qualities, a trimmer for grass takes first place among other options for remaking options.

Features of a homemade engine

When converting the motor, it should be borne in mind that they were developed to perform different functions. The trimmer for grass functions at large speeds and a small spinning moment, and the boat motor should do the opposite. Therefore, alteration of the device requires special tools and even a drawing.

The engine from a trimmer for grass is more convenient and easier to build, since it has a number of necessary components of the mechanisms:

It remains only to buy the missing details or make them yourself and you can start making an engine for a boat.

The trimmer for grass functions at large speeds and a small spinning moment, and the boat motor should do the opposite

What can be done

There are several possible options for finalizing a trimmer for grass for a swimming engine.

A very simple way, but requires additional financial costs.

You will need to purchase the following details:

Advice! Sometimes there may be a clamp, so before buying it to clarify what is included in the kit.

The attachment drawing to the trimmer is indicated in the instructions. For installation will need about half an hour.

To remake, you will need an angular gearbox from a corner grinder, a screw that can be cut out of a sheet of stainless steel, as well as seals and bearings for fasteners. This method allows you to get maximum speed, despite the small step of the screw. In the field atmosphere, the device requires additional adjustment, which is performed using pliers.

This method is performed as much as possible. Consider it in more detail on the example of a lawn mower with a two.Stroke engine with a volume of 25 cm3. The device weighing 4.5 kg and 700 watts is equipped with a bent leg. Trimmer for grass with such power allows you to move a boat at a speed of about 5-7 km/h.

To remake, you will need an angular gearbox from a corner grinder, a screw that can be cut out of a sheet of stainless steel, as well as seals and bearings for fasteners

What is required

Materials, as well as tools, will be required:

All the necessary elements can be bought or made independently. The drawing may be needed to develop a home.Made screw, but not for the drive. The dimensions of the screw directly depend on the power of the drive, as well as on the weight of the swimming agent. For example, a screw with dimensions of 10×3 cm is able to move transport with a mass of about 120 kg.

Production instructions

To make a boat engine from a regular trimmer for the grass, you will need to perform the following actions:

Reduce the bent shaft. To do this, extract the standard nut, which is located in the bobin with a fishing line. It looks like a small tube 2 cm long and has an internal thread. It can be divided into two full.Fledged nuts.

Advice! In no case do not throw away and do not lose the nuts, since the developers use their own type of thread, which is not a metric or inch. Next, it is necessary to remove the plastic lining, which is located on the gas button.

There are no roller bearings at the end of the curved rod, instead there is an ordinary bronze sleeve, still known as a sliding bearing, it must be extracted. To do this, you will need to carefully cut it, having previously unscrewing the nut and eliminating the metal and diudwood shaft from the tube.

Having freed from the bronze sleeve, you can start knocking out a flexible shaft tread, which is made of plastic. Advice! The steel pipe can be thrown away, since it will not work to align it. Instead, we use a duralumin tube with the corresponding diameter.

In the duralumin tube we mount a bronze sleeve and gently press it on a canvas using a hammer. Then we take a plastic tread, cut it a little in diameter and tightly mount it in the pipe.

Advice! Когда наружный диаметр трубки больше и не пролезает в крепежное отверстие на моторной головке, потребуется его проточить до нужного размера. If necessary, you can build a longer shaft using the tube of the desired length, and installing the required length of steel rods instead of a flexible shaft of the required shaft.

To run up a home.Made engine, you will need a gas tank (0.5 l.) with oil in a ratio of 1:40. One fuel tank allows you to overcome about 10 km of territory. The speed of a swimming agent with such a motor is in the range of 5.6. 7.9 km/h, depending on the load of the boat.

Blitz-councils

0.00, (estimates: 0) Loading Poachers, having caught 317 kg of fish, did not suffer punishment

A group of fishermen during interrogation revealed the name of a secret bait.

How to make a trimmer for grass with your own hands from corner grinders, vacuum cleaner, drills, chainsaws

All owners of personal plots are faced with the problem of mowing grass, which grows literally before our eyes, and during the season it is required to ennoble their site several times. The usual manual spit has been replaced by benzotrimers and electrimmers for a long time. But the price of them does not decrease and is quite noticeable for many owners of cottages and private houses. People’s craftsmen still found a way out of this situation and learned to make trimmers for grass with their own hands literally from improvised means, using benzo- and power tools not intended for these purposes.

From corner grinders

Most often, a homemade electric trimmer for grass is made on the basis of a conventional corner grinding grinder, which is available to every home master. This tool is almost perfect for remaking into a trimmer for grass. It has a larger power than store machines and more than a minute. In addition, the standard nut used in the corner grinding for fixing the disks already has holes through which it is easy to insert a fishing line for a trimmer (cord).

So, there are many options from which to make a bar (holding). The simplest is the longer a wooden holder than for a shovel. To the end of it, an angular grinder is attached at the right angle with a conventional tape. The fishing line for the trimmer is inserted into 2 holes of the nut, after which it is twisted. Thus, in a few minutes you get a trimmer for grass, which can be mowed without problems.

For the safety of the operation of a home.Made apparatus, you can improve it by making a protective casing (how to do this, will be considered later).

For advanced masters with a welding machine, you can advise a more advanced design to fix the angular grinder and protective casing. It is made from an aluminum tube (serves as a holder) and a metal square profile. Looking at the picture below, you can understand the principle of manufacturing the holder.

The corner grinder is fixed on the holder with bolts inserted into the holes that are designed to attach the handle to the device.

The following photo shows how this design looks below.

By the way, you can fasten the holes for fastening the handle (bar) itself, when you want to make a simple trimmer for grass, which is easily assembled and is also easily versed if you need to use the corner grinding for its intended purpose.

To make it more convenient to hold a trimmer for grass in his hands during work, and it did not rotate around the axis of the bar, you can attach a side hand made of a bent pipe to it.

From the vacuum cleaner

The trimmer for grass from the engine from the vacuum cleaner is made according to the same principle as from the corner grinder. The motor must be fixed on the rod, and either knives or a plastic or metal disk in which the fishing line for the trimmer is fixed on the engine shaft. On top of the cutting tool is closed with a protective casing.

So that the dust and small particles of mowed grass do not fall into the engine removed from the vacuum cleaner, it can also be hidden in a plastic casing made of a sewer pipe, as shown in the next photo.

Since the engine in the vacuum cleaner is high.Cost, it needs to provide cooling. Therefore, it is recommended to insert a homemade disk with cut and curved blades under the washer, into which the fishing line is inserted, so that it plays the role of a fan that creates a vacuum. It is required so that the air is sucked through the hose from above and cool the motor.

In order to facilitate the load on the hands of the mowing operator, the unit can be installed on the site with wheels. In this case, something similar to the lawnical mower will be obtained.

To fix the fishing line, you can also use either a pulley with a suitable landing hole, or a plastic wheel from a cart.

From a drill

The simplest mower in a matter of minutes is made from a drill or an electric screwdriver. But first you must make a knife from a sharpened metal plate with a hole drilled in the center. A bolt is inserted into this hole and clamped by a nut.

Since a drill with this nozzle does not have a protective casing, such a tool is quite dangerous for the user. To protect yourself, you can place the drill, like a corner grinder (this was mentioned above), on the cuttail cuttings or on an aluminum pipe.

Also, to protect the user of the mowing from knives, you can fix the casing on the drill (attached to the plastic pipe and put on the body of the apparatus).

The drill to the bar is attached using clamps.

From a chainsaw

For the chainsaws, many different nozzles have already been invented, expanding the capabilities of this unit, for example, a cultivator, a drill, a boat motor, as well as a spit nozzle for grass. How she looks, you can watch in this video. If you want to make a trimmer for the grass from the chainsaw, then the maximum that you can do is the lawn mower on wheels, since the unit engine is quite heavy, and apply the above.Described trimmers manufacturing (with the lower drive).

Homeps from electric screwdriver: an electric generator, corner grinder, trimmer for grass, lawn mower, engraver, bureau

Electric screwdriver is widely used in various fields of activity to work with fasteners of various kinds: self.Tapping screws, screws, bolts with nuts, furniture confirmation, screws and others. Also, with the help of this power tool, holes in different materials, for example, in various metals, in lumber, in concrete, are fused. In this case, the functionality of the operated model is determined by the magnitude of its power and torque, the presence of shock function.

From an electric screwdriver, you can make a variety of equipment and tools for domestic use at home. In addition to the power tool itself, in many cases, additional details and materials will require in many cases. But homemade devices will still cost cheaper factory analogues, allowing to automate and make a more efficient manual work.

Ideas of homemade equipment from electric screwdriver

The entire range of screwdrivers is divided into network and battery models. Both varieties of products work due to electric energy, which rotates the electric motor. Only the electric motor itself in network devices is designed for a variable voltage of 220 V, and in battery equipment for constant different sizes, for example, 12 V, 14.4 V. These design features, together with the technical characteristics, largely determine which home.Mades from the electric screwdriver will be possible to collect.

Electricity is one of the main types of energy used by mankind. Due to electricity, household appliances, industrial equipment, machines, power tools are functioning. The work is performed by electric motors of different structures and power, which are powered by variable or constant types of current. For this reason, on the basis of an electric screwdriver or from its individual parts, the following technical devices can be assembled:

  • Garden grinder of grass and branches;
  • Trimmer for grass (electric couture);
  • Hiking manual generator;
  • Engraver (mini-spray, dremel, drill);
  • Wind generator;
  • Lawn mower;
  • Corner grinder;
  • Mini-stations: drilling, grinding, precise, current, sawing, hiding;
  • Tool for knitting reinforcement;
  • Gate opening drive;
  • Vehicles for children: square, bicycle, scooter;
  • Small ice drift, Yamobur, construction or kitchen mixer.

A powerful shock type model can also be converted into tamping for concrete using a special nozzle.

The implementation of each option takes different times and requires additional (insignificant) costs, or does without them at all.

Assembly of a manual camping electric generator and a home.Made wind generator

Of the battery models, it will not be difficult to make a home.Made generator that will issue electricity when rotating the attached handle. This device is useful in camping conditions. To make a dynamo machine, you do not need to radically modify the product. Everything you need to create a camp generator in the design of the device already have, only minor improvements will be needed.

Using the created equipment, it will be possible to charge batteries 6 or 12 V.

For remodeling, a power tool with an operating voltage of 18V and above is suitable. Modification is carried out in the following way:

How to make a electric bike using starter motor

  • Gently fall out the electronic board;
  • Instead of batteries, a diode bridge suitable in terms of parameters (dimensions, technical characteristics) is placed into the battery body;

The final design after the manipulations done will be like in the photo below.

The diode bridge is necessary so that the electric generator handle can be twisted in any direction. Instead of the handle, you can insert a nozzle with blades. Then you get a simple wind generator.

The electric generator working on wind strength is also made in another way, in the form of a weather vane. At the same time, they do this with the battery:

  • A shaft of an electric motor is inserted into the cartridge, clamping it;
  • A round metal plate of about 1 mm thick is attached to the gear of the gearbox, which will serve as the basis for fixing the blades made, for example, from plastic pipes;
  • The clamp with a clamp is dressed on the shaft between the cartridge and the gear;
  • Cut out of plywood or thin metal a rectangular base;
  • Using a clamp with a clamp, a engine with a cartridge is attached to it, drilling under the fastening of the hole in the right places;
  • Make a casing to protect the wind generator (from precipitation, dust and other unforeseen influences), for example, from under the coffee can;
  • Insert the base with the engine and cartridge inward, fixing the elements with glue, and the lid with sealant;
  • Make the blades, attaching them to the round plate of the unit;
  • Make a weather vane;
  • The assembled generator is mounted on one of its ends;

There are many options for wind generators. Even the entire electric screwdriver is attached to the support, supplying it with a nozzle with blades.

Alteration of an electric screwdriver into a corner grinder

If the corner grinding machine broke or it is completely absent, then its temporarily can be replaced with a battery or network electric shurubrust. In this case, there are various options for remaking. The easiest way is to use ready.Made or home.Made nozzles or adapters. An example of an adapter is presented in the photo below. One end is fixed in the cartridge, and the disk clings to the other.

| Denial of responsibility | Contacts |RSS