How to make a shoal car for a walk -behind tractor. Spring

How to make a shoal car with your own hands from a walk.Behind tractor

A device with a screw is easy to distinguish even in appearance. The screw-cutter located in the center works on the principle of screwing the methys of the dignity into the tree. An electric motor is placed from the back, thanks to which the device works. Rotation is carried out until the limiting point of the strength of the fibers reaches, after which the workpiece split. The nozzle in the form of a cone with chopped thread is gradually refined to the working part, turning into a narrow tip, thanks to which the entrance is easily entered into the wood. The more significant the dimensions and more powerful the engine, the greater the speed it is possible to make logs from a wooden chock.

The main advantage is the maximum simplicity of the design. A two-phase engine is required, with a capacity of 3-4 kW. For home conditions, 80 mm diameter of the screw is enough, with a 250 mm length length. The disadvantage is the low level of security during work and the need to independently bring the workpieces on their own. This does not exclude physical fatigue during work, although it significantly accelerates the process of chopping firewood. The fastest model of the Kone Loaming Coast is considered, which can process in 2 hours 5 cubic meters of firewood.

General information

Before you build a plan, how to make a shoal car from a walk.Behind tractor, it is necessary to conduct an excursion into the technology. There are many classifications of such attachments according to various signs, one of which is the principle of functioning. Based on this fact, the laborers installed on a single tractor are divided into:

The first two types from this list can work regardless of the walk.Behind tractor. There are other classifications. For example, they are divided into mobile and stationary. The first type is characterized by small dimensions, it is not intended for large volumes of work and is easily transported. Stationary, on the contrary, are performed in the form of massive machines. Their task is to harvest very large batch of firewood. They are not intended for domestic use, they are installed in specialized enterprises where work is underway with wood.

Another classification that is relevant for those who are directly related to the harvesting of firewood is the direction of the supply of churbak. Based on this characteristic, the laborers are divided into:

make, shoal, walk, tractor, spring
  • Vertical. In this configuration, the supply of the cutting mechanism is carried out from top to bottom. Such types of laborers are also called hinged.
  • Horizontal. The basis of such lambols is a flat platform (desktop). It houses a splitting peak, to which a log is supplied.
  • Mixed. Such devices allow you to carry out a multi.Position harvesting of firewood.

Despite many varieties, for domestic use, the key factor is still the principle of operation. Based on this feature, consider which type of laborer is optimally suitable for your walk.Behind tractor.

1962 Simplicity Walk Behind Tractor Model W in Action

make, shoal, walk, tractor, spring

When firewood is helped

Compler parts Lesin and, especially, stumps from the feeding, as you know, give, burning, a lot of heat. You can purchase them on firewood inexpensively, and in Russia in some places just for pickup: for cellulose, fiber for wood-fiber slab and technical chief for OSP, wood-steering plate and wood-fiber plate are not suitable. But to split such a clumsy churbak on the outside is not so easy. However, for the harvesting at home a small amount of additional wood fuel, this task, which are still fighting woodworking experts, is quite solved. How? It is necessary to make a conical shutter: it does not split the churak by force, but forces it to crack as it is more convenient for him. If the workpiece is not more than 60 cm in diameter, then the resulting logs will fit into the furnace furnace. Their transverse dimensions are not optimal for the most economical combustion, but also the fuel of the catchy.

See also  Which oil is suitable for a walk -behind tractor. Chemical composition

A conical shutter device is shown in rice. On right. The diameter of the base of the cone is 80-150 mm. The angle at the top is 15 degrees for small.Layer and 18 degrees for a straight.Layer tree. Approx. At 1/3 of the height of the cone from the base, it is replaced by the angle of the solution 22 and 25-30 degrees, accordingly. The jack is better to apply rack. The fact is that Auto.Ore emergency device, not designed for frequent regular use. There is nowhere to simplify the rack jack, but the hydraulic in the cheek will flow pretty soon. For comparison: stamping hydropress, developing the same effort is a solid structure more than a ton weighing.

make, shoal, walk, tractor, spring

The Simplicity Walk Behind Tractor Comes To Life! (Model FB)

Another nuance: the adjusting stem of a conical cornflower is better to make a worker. To do this, it is made of a bar of steel st45 or a more durable diameter of 24 mm. The thread is cut trapezoidal (you can use parts from unfit.Line gas or water valve). The helm is replaced by a lever gate. Then together with the assistant it will be possible to split the most fat vile of the vile churak. Rama. Channel from 150 mm and pipes from 60×4.

The specifics of the Loam

The shoal car to the walk.Behind tractor is a hinged equipment that can be combined with all heavy models of units. Often it is installed on Neva, bison, agro and others. There are only two restrictions on the use of this nozzle:

The equipment has a standard design:

  • The presence of a powerful metal cone with a screw thread and a thin sharp tip on the bed;
  • The nozzle moves due to the belt from the power shaft. After turning on, the rotation of the shaft begins, the cone is screwed into the log and divides it. Starting to work, the tree must be held until the shaft is completely screwed into the wood;
  • The presence of an adjustable table for finished firewood.

Cloth a special cone with a thread. It easily enters the wood fibers, tearing them. So the logs are split in half. The shoal car is easy to use, mobile, is characterized by high reliability and speed.

The process of reconstructing a home.Made screw dive for a walk.Behind tractor takes place in several stages:

A selection of material base;

  • Creating a drawing drawing. We offer ready.Made. Standard installation dimensions should be in the range of 850 x 400 x 650 mm, and the screw-blade itself will have a diameter of 8 cm, length-28 cm, the length of the cone neck-90 mm, parts with a protected thread-19 cm. The thread of the thread is best done within 6-7 mm;
  • Production of a shoal cone for a walk.Behind tractor. We will need a steel block, which is given a cone.Shaped shape on a lathe. If there is no such equipment or skills at the disposal, it will be ordered from a specialist. At this stage, it is important not only to withstand the proportions indicated above, but also to observe the inclined angle. Subsequently, it will depend on it, for the size of which wooden trunks it will be used;
  • After the cone has been driven, they cut the thread on it, you need to take care of the landing place with which it will be aggregated with a pulmonary pulmonary clock. The optimal diameter is 34.85 mm, although smaller values ​​are also acceptable. The neck of the cone should have a smooth cylindrical surface, which is an adapter between the base diameter of the cone and a specific diameter of the bushing (adapter). In order for a homemade megger from the walk-behind tractor to be no different from its production analogues, a number of technical and operational purposes are made on the neck of the cone:
  • The 1st, located next to the seat will serve to stop the bolt from the shift of the axis and pressing the motor shaft;
  • 2nd. Serves to compress the cone from the shaft to protect the thread from damage;
  • We create a planting of a jelly cone from a walk.Behind tractor. Ideally, it should be a keyboard with a groove of 10 mm;
  • We collect a bearing knot, as described in the video. To do this, you need to buy a shaft with bearing racks that are located on a horizontal surface. In order to save money, it can be replaced with a pulley from the crankshaft “Vase”, 2 motorcycle stars and a metal chain (belts);
  • Adaptation of the support site. Its width should not be less than 450 mm. Made of cast iron or steel completely or only a countertop;
  • We put the motor. It is better to place it at the bottom of the homemade, the screw. On the desktop. Above 20 cm from the countertop, the screw should not be placed: from this it can turn over and damage others.
See also  What days it is impossible to make noise with a hammer

How to do it yourself

Before starting the assembly, you need to decide on the unit diagram and its main function, t.To. Different types of wood are strong. If the mechanism is used only for its own needs, then it is recommended to build a vertical shift. It is less effective and fast, but it is easier to make and mobile. After that, you should decide on the engine. The gasoline engine will allow the use of the device anywhere, and the electric drive only works for a socket or battery, which will not be enough for a long time.

If a person does not have his own tractor or details, then it is best to choose a manual mechanism. It consists of 2 main details. A jack and blades. The log under the influence of the jack will rise, and the knife will begin to cut the material. The main thing is to tightly fix the elements on the frame.

Tools and materials

The device of the case, table and blades do not play an important role, t.To. They are selected for the needs of each master, so they can be made from any available materials. However, there is a minimum set of details that any shift.Glass should be equipped with:

  • Hydraulic pump.
  • A motor connected to a hydraulic pump. It is the main element of the mechanism on which the effectiveness of the unit depends. If the motor turns out to be weak, then the tree will not work out due to frequent jamming, breakdowns.
  • Liquid distributor.
  • Water container.
  • Sleeves.
  • Connecting tubes and clamps.

Assembly process

To build your shift, you need to perform several actions:

  • Make a knife from a metal sheet, the thickness of which is at least 10 mm. For particularly solid varieties of wood, for example, yarres, yatoba, it is better to take a professional blade made at the factory. And for processing large logs, it is recommended to make an integral knife with a thickness of more than 50 mm, it can be strengthened by a steel blank.
  • Put a gear 5 cm above the bed. The double length of the log should remain to the blade.
  • Make a movable carriage on which wood will be fixed and pass through the knives. You need to put it at the height of the six.
  • On the front of the carriage, install a pusher. It is often made of a metal plate.
  • Ensure the mobility of the rail using a hinge.
  • Put a return spring so that the carriage quickly returns to the place after the saw. It is attached so that the rake can rise above the gear.
  • Install a clamping lever. When pressing it, the rail should press the gear and move forward.

Drilling to a walk.Behind tractor: Operational features

It is worth noting that such a hitch will fully fulfill its task only in combination with an aggregate with a capacity of at least 8 liters. With., After all, basically the shoal car works with the engine from the walk.Behind tractor. The presence of water cooling is also advisable, since this feature will contribute to the low wear of the motor and greater endurance.

The principle of operation of the device is very simple. It is known that while screwing the screws into the wood, its fibers are parted, only from the small screw there will be no sense. Therefore, experts increased it, creating a massive cone with screw carvings.

See also  Husqvarna 128r stalls when you press the gas

A considerable pressure will push the device into the log, tearing it into several parts. At the same time, a person will not need to use special physical strength. The basic advantages of working with the machine include:

  • High productivity;
  • Reliability;
  • Mobility;
  • Compactness;
  • Relatively small weight (about 20 kg);
  • High quality of the metal alloy.

The hitch is suitable for Neva, a centaur, Viking, Champion and other brands, both domestic production and foreign.

The shoal car for the walk.Behind tractor is attached to the car and works thanks to the belt installed on the VOM. The belt itself drives the cone, which begins to spin.

The user only needs to bring the log to the tip of the cone, which will capture the wood and will break it in a matter of seconds. Axes and saws do not participate in all this process.

General information

Before you build a plan, how to make a shoal car from a walk.Behind tractor, it is necessary to conduct an excursion into the technology. There are many classifications of such attachments according to various signs, one of which is the principle of functioning. Based on this fact, the laborers installed on a single tractor are divided into:

The first two types from this list can work regardless of the walk.Behind tractor. There are other classifications. For example, they are divided into mobile and stationary. The first type is characterized by small dimensions, it is not intended for large volumes of work and is easily transported. Stationary, on the contrary, are performed in the form of massive machines. Their task is to harvest very large batch of firewood. They are not intended for domestic use, they are installed in specialized enterprises where work is underway with wood.

Another classification that is relevant for those who are directly related to the harvesting of firewood is the direction of the supply of churbak. Based on this characteristic, the laborers are divided into:

  • Vertical. In this configuration, the supply of the cutting mechanism is carried out from top to bottom. Such types of laborers are also called hinged.
  • Horizontal. The basis of such lambols is a flat platform (desktop). It houses a splitting peak, to which a log is supplied.
  • Mixed. Such devices allow you to carry out a multi.Position harvesting of firewood.

Despite many varieties, for domestic use, the key factor is still the principle of operation. Based on this feature, consider which type of laborer is optimally suitable for your walk.Behind tractor.

Classification of the Loams of the Field of Application

The dimensions and the principle of operation of the device for Kolka firewood depend on the scope of its application. So, for example, at construction sites and sawmills you can often find a rather bulky, but powerful shutter machine, and in private houses. A small compact homemade clay.

By the scope of use, clans can be classified as follows:

  • The log is placed in the gutter, which is located opposite the knife, the length and width of the gutter can be adjusted depending on the size of the log;
  • The main elements of the cornfield is the piston. It pushes logs, and it moves forward;
  • The piston pushes the log, after which a knife comes into effect, which cuts the log into parts of the desired size;
  • The log is fixed in a fixed position, and the knife drives back and forth and cuts the log into parts.

The shimmer is an indispensable assistant

The main disadvantage of the so.Called household contamant is that it cannot be used to process large logs. Before you stab a large log, it needs to be cut into several parts.

| Denial of responsibility | Contacts |RSS