How to mow an electric trimmer. The duration of the mowing

electric, trimmer, duration, mowing

Proper operation of a trimmer for grass for grass

In every summer village, village, suburb and in the city itself you can see these devices: they work tirelessly, aligning the lawn grass, cleansing the space of squares and parks, gardens and gardens from thickets of burdock, wormwood and weeds. The noise and crackle from the trimmers are heard from the beginning of summer to autumn, until the growth of the grass is so much so that it will no longer need to trim it. Automatic braid for grass deserved its popularity for the simplicity of the device and operation. It is easy for her to use, it is easy to care for, and in case of breakdown it is not possible to easily fix it without difficulty. The article will just tell you how to use a trimmer for grass correctly.

As with any other technique, in working with the trimmer there are rules. First you need to make sure that the main nodes and assemblies: screw, rods, handles and motor. If the device has not yet been assembled, then it should be correctly assembled according to the instructions.

Gasoline unit

In the case of a gasoline trimmer, it is necessary to check the gearbox for lubrication. Also, do not forget to add lubricants to the fuel tank, if the instruction manual is evidenced. As a rule, gas and oil are mixed in a ratio of 45 to 1, but these indicators may vary depending on the model and manufacturer, so you should carefully study all the technical requirements for the device. The fuel container must be filled on the very neck. If all technical fluids are flooded, then you can try to start the device. But it’s not worth mowing right away, it will be better to let the trimmer work without load so that the engine works to the flooded fuel. A few minutes will be enough, after which you can give the motorcycle full load.

Elektokos

With an electric trimmer, everything is much easier. Having made sure that the gearbox has the required amount of lithol, you can start work. No additional measures are required. Unless it is necessary to make sure that the carrying does not run on the path of mowing in order to avoid possible damage.

When the device itself is ready to work, you should make sure that there is nothing around that could interfere with the work. If possible, the estimated mowing area should be cleaned of snags, glass, stones and other solid objects that can damage a knife or fishing line for a trimmer.

Product Review | Trimtech 2600W Electric Mulch Lawnmower

It is better if other people do not approach the trimmer while working. Usually the recommended distance is at least 10-15 meters in order to avoid small debris (mulch) in the eye and on the face.

Depending on the upcoming work, you need to choose a nozzle for a trimmer for the grass: a screw-knife for weeds and hay, a fishing line for a trimmer for lawn grass or a disk saw for shrubs. Mowing should be in the opposite direction from people, if possible, moving away from buildings and buildings. You should not get too close to the fence and other designs, since the fishing line for a trimmer can catch on sharp edges, and the screw-knife will bend if it accidentally offends it a hard object.

The preparation of the device itself will not take much time, all modern models of devices are designed to facilitate and simplify their operation, starting to work in the shortest possible time.

How to use a trimmer for grass, if the grass is very high

If, upon arrival at the cottage, you found that the grass is very high, it will probably not be possible to perform its mowing with one passage with one passage. If you try to mow it right under the root, then it will simply be wrapped in a coil. And as a result it will block it. That is, a trimmer for grass simply cannot work. Over, it can overheat and fail.

If the grass is too high, then the mowing must be made in several visits. First, you need to cut the top of the plants. And only then mow them under the root.

But in any case, in the case of winding, the work should be suspended to clean the device. And only after that continue the kosbu. This will avoid overheating of the device and its breakdown.

What to opt for

What is better to choose for your site? You need to know for what purpose the device is purchased. In case of work in a small area with uneven relief, you need to stop at the trimmer. It is ideal for conducting accurate pumping of grass growing in hard.To.Reach areas. They can also decorate the edges of the lawns, work along the walls and fences.

And if the entire territory is faced with 6-10 acres, then it is better to opt for a lawn mower-this will save time and time (especially if you choose a convenient and maneuverable model). In addition, the result will be a exactly cut grass carpet.

Experienced gardeners advise to have both devices in stock. This advice is perfect for owners of plots with variable landscape.

Gasoline gas mowing gasoline with butter

Before mowing grass with a benzo.Leggos, it is necessary to season the tool with fuel. As fuel, gasoline with butter is used. However, take into account that mixing gasoline with oil is needed only for two.Stroke engines. Four.Stroke engines operate on pure gasoline, since their design has a separate container. Oil crankcase. There are no 2-stroke gas crankcases in the design of the 2-stroke gasolimers, so you need to pour exclusively gasoline with oil into the tank.

As gasoline, it is recommended to use AI-92 brand fuel. In order not to make a mistake in choosing, you need to read the instructions offered by the manufacturer. Often, most manufacturers recommend using the AI-92 brand fuel, and only some recommend filling AI-95.

Gasoline must be diluted with a small one in a proportion of 1 to 25. This means that 40 ml of two.Stroke oil must be added per 1 liter of gasoline. However, not everything is so unambiguous here. The proportion 1 to 25 is universal, but each tool model has its own values. These values ​​are also indicated by the manufacturer in the instructions. Details about how to properly dilute gasoline with butter into a lawn mower is described here. After breeding gasoline with butter, pour a full tank, and start work.

It is interesting!If a four.Stroke lawn mower is refuel, then pure gasoline must be poured into the tank, and engine oil is added to the oil container to the maximum level.

How to mow grass with a trimmer with a metal knife

As the border of the mowing area moves, move the fuel and the bag.

electric, trimmer, duration, mowing

If the grass was setting down: you need to hand the steering wheel forward and mow to the left with an inclination by the handles to the left (sector ~ 11 hours) and the right with the tilt for the handles to the right (sector ~ 1 hour), and do not rush!, to mow the grass cleanly and so as not to “dig” the earth.

See also  What is the best line for an electric grass trimmer

During the mowing of grass (and turns), do not forget to look around!:

  • To notice the gesticulation of others, drown out the motor and remove the headphones,
  • So that closer than 15 m children, animals, spectators and assistants do not come up, t.To. When a metal knife in the grass collided with a motionless object, a trimmer for grass or a lawn mower (motorcycle) can be strongly thrown to the side or expanded back, and a trimmer for the grass rotates at a speed of up to 10,500 rpm. And he is able to cut off his hand or leg.Also, when the grass is mocking the trimmer from under the knife, various objects (crushed stone, glass, garbage) can fly out and ricochet).

How to mow grass with a trimmer (more about the mowing technique)

The engine revolutions when the trimmer mowed depending on the load on the engine. The thicker the grass and, of course, is heavier than the engine, the bolder you need to open the “hole” (throttle in the diffusor of the carburetor).

Work speed of the engine during the mowing of grass with a trimmer try to keep constant (slightly higher than medium). Or less gas. Only depending on the overall load on the engine. No need to completely discard gas (and immediately acceleration again) with each wave of braids for grass. And the clutch is not for long, and the edges on the drive shaft can “overtake”, and the overall wear of the trimmer for grass (motorcycles) increases sharply.

Before mowing grass, we find out the parameters of the site

(to know which knives to take, how much fuel and time are needed)

  • Grass density;
  • The hardness of the grass;
  • The splendor of the grass;
  • Wovenness of grass;
  • (The height and thickness of the grass are not important)
  • The boundaries of the site;
  • What irregularities (how to come in);
  • The presence of hidden obstacles (remember)
  • That not cut (bushes, flowers, seedlings).

To mow grass in the summer is a disaster, and not just homework how to use a trimmer. If your yard or site is strongly overgrown with grass, you can scare you, but this part of the article will help to figure out how to mow grass with a trimmer easier and less irritating.

Problems with fishing line

Trimmeres users, both gasoline and electric, sometimes have problems with the cord. “Advanced” Kosilov owners can easily cope with the difficulties, realizing why this is happening, and for beginners, this is a problem that does not have a rational explanation. But in fact, everything is solved quite simply. The most common problems that happen to the fishing line are the following.

Cords of cord

If a trimmer fishing line is often torn, this can cause the following reasons:

  • Stones, small branches and other hard obstacles come across the grass;
  • The user mows the grass back to the fence, and if he is mesh, then this breaks the “antennae” even faster;
  • Poor quality of the cord (it is recommended to purchase high.Quality);
  • The output holes are worn out in a mowing head, which is why the fishing line for a trimmer is erased on the sharp edges of the bushings and breaks off (a complete replacement of the part will be required).

Large cord consumption

Basically, the cord quickly ends if you often knock on the ground with a semi.Automatic head or press it hard. The coil unlock occurs, and the fishing line for the trimmer, lengthening, is cut off with a knife. Another reason that the cord quickly ends is the improper operation of the device with an automatic head: the user during kosbe often drops engine speed. But as we recall, the automatic head is arranged so that it is with each reduction in the revolution that a new portion of fishing line is supplied, so it is quickly consumed.

The thread does not hold

It happens that the thread is unwound if the spring weakened in the semi.Automatic head. The fishing line for the trimmer is constantly extended and cut off with a knife installed on the casing, which increases its consumption. To check this, remove the casing and turn on the unit. If the fishing line for the trimmer “climbed”, then you will need to replace the spring.

A fishing line for a trimmer flies out

The reason that the cord after starting the unit is unwound is also a weakening of the spring inside the head. In addition, there are times when when the unit is turned on, a spitter head is scattered, and the spring installed in it is lost. Inexperienced users do not notice the absence of a spring and collect this node without it. Therefore, the cord does not hold, and under the influence of centrifugal force flies out.

The cord is not served, the coil does not spin

Automatic or semi.Automatic head should serve a fishing line for a trimmer without stopping the unit. But if it does not come out, then the reasons may be as follows:

  • The fishing line for a trimmer in a coil is incorrectly wound, which is why the latter does not spin;
  • The cord is wound unevenly, and the thread can get stuck between the turns (the thread should be wrapped neatly, the turn to the turns, without distortions);
  • Too short ends of the threads come out of the holes, as a result of which there is not enough centrifugal force to extract them, and the fishing line is not supplied for the trimmer (it is recommended to always adjust the length of the cord before starting the unit, slightly pulling it up);
  • The fishing line for the trimmer is sticking together (it will be considered later).

The thread sticks together

This nuisance occurs most often due to the use of poor-quality cord. When the apparatus is operating, the head of the trimmer for the grass heats up, and a poor.Quality fishing line for a trimmer in it melts, gluing among themselves. Also, sintering of the threads occurs when a fishing line with a solid obstacle occurs. In this case, there is a sharp braking of the cord, after which it drags it into the head, where it bothers. Some unit owners recommend lubricating the cord with mineral oil or spray on it with a silicone spray after winding on a spul. Others advise to wrap less threads on the coil. But it is better to immediately buy a quality product, in the manufacture of which the manufacturer took into account the factor of overheating of the head, and the thread will not stick together.

Rules for operating a trimmer for grass

In addition to the mandatory configuration and running.In before starting work, a number of rules must be observed so that the mowing is comfortable, the result is the best, and the service life of the apparatus is long.

Use of the belt

Before starting a trimmer for grass, you need to attach a belt to the assembled and ready to work. Fasten to the bar with a metal loop. Such a mount withstands large and long loads. You can wear a belt in some models on one shoulder, in others. On both (backpack straps). When the large areas are spent, the arms and back are tired of the weight of the device, but if you put the belt correctly, you can reduce the load and prevent the appearance of pain in the muscles and joints.

electric, trimmer, duration, mowing

Lawn haircut

For this task, you need a cord, since the grass on the lawns is softer than the usual. First, make sure that there is no large garbage, branches, wire, stumps and irregularities on the processed territory. The lawn should be trimmed evenly, that is. The height of the grass should be the same in all parts of the lawn. To properly mow a trimmer with a fishing line, the device should always be kept at the same level from the ground, drive them from right to left, smoothly and without haste. You can divide the territory into squares and cut them out sequentially. It is recommended to move from one to another clockwise.

See also  How to put on a harness for a trimmer for grass. Belong belt Redverg

Advice! If you need a lawn of the minimum height, the angle of inclination of the device to the ground should be at least 30 degrees so that the fishing line for the trimmer almost touches the surface. Flaws can be removed manually using garden scissors.

Help

Hay should not be too small, so you need to mow under the root. It is better to go to the mowing with the disk, because the meadow grass is tougher than the lawn, and the fishing line for the trimmer can not cope with it. You need to lower the trimmer for the grass as low as possible, try to pump out stripes of the same length. Bushes and large weeds with durable stems are better to bite in a circle so as not to damage the disk. The trimmer for grass, as in the case of the lawn, should move from right to left.

Powder of high grass

In this case, it is necessary to draw a trimmer from side to side twice to remove the height of the grass, and then mow it under the root. Three or more movement may be needed. It depends on the length of the stems. Cutting hard grass at the base is better with a disk.

Important! It is better not to cut high grass right under the root. The stems can wrap the fishing line for the trimmer and cause overload of the motor.

Mowing wet grass

During and after rain, cut the grass with an electric device is dangerous! Moisture can cause a short circuit in the engine, a trimmer for grass can burn, and a person can get a shock. The dew is also dangerous, especially for devices with the lower location of the motor, and network models that require an extension cord. It is safe to trim the raw grass with a motorcycle, although gasoline units with a low degree of protection against moisture must be protected from the rain.

Important! About whether it is possible to mow wet grass with a specific model of motorcycles, should be clarified in the instructions. After mowing, a wet trimmer for grass of any type must be carefully dried.

Selection of revolutions

Spindle rotation settings are possible only on gasoline devices. This option is used for different types of work:

  • Low speeds are suitable for cutting lawns;
  • Medium. For high herbal thickets and thin shrubs;
  • High. For cutting thick branches and bushes.

How much time can a trimmer mowed for grass

The device with an electric engine is able to work up to 20 minutes in one turning on. Then the device will need to be turned off at the same time that the motor cools down. Battery charge must be periodically checked.

Lawn mowers can function up to 40 minutes and even up to an hour without a break for engine cooling. Then they need to be drowned for 10-20 minutes. How much time a specific lawn mower will work, also depends on the volume of its fuel tank.

How to care for trimmers

Each type of device has its own features that must be taken into account when working and storing. But some rules are applicable in all cases.

General recommendations

These tips should be followed by users of any travo.Shirts. Gasoline and electric.

  • Store the device in a dry room.
  • It is better to hang it on the wall, on a special mount.
  • After each use, the device needs to be cleaned from dirt and beveled grass, examined for damage and wipe the surface with a soft rag.
  • Before the work, you need to check whether the bolts fastening parts of the unit are well twisted, especially the fasteners of the working head.
  • It is better to wash herbal juice from the coil immediately after the mowing.
  • It is necessary to monitor the amount of fishing line and the condition of the nozzles of metal or plastic. The fishing line for the trimmer should be suitable for the diameter (for the bastard used and the type of thicket). The blades of the discs and knives must be sharpened, and two.Way nozzles should be turned over for uniform grinding of the teeth.

On a note! The grass is often wound on the coil, bar and gearbox. This slows down the rotation of the spindle and creates an excessive load on the engine. Long stems and leaves should be removed from a trimmer for grass immediately after a mowing or during breaks.

The boots of the cord on the bobin should be uniform, without overflows. The fishing line for the trimmer must be wrapped in the right direction and in the recommended number. There are tags on the coil: arrows for indicating the direction and risks to indicate the border.

Large shrubs, trees, fences and other solid obstacles should be pushed around the perimeter, while the trimmer for the grass should be rotated with a casing to the barrier. Otherwise, fishing line consumption will increase, and the blades will dull very quickly.

Features of the care of a gasoline trimmer

Powerful, designed for long.Term continuous work, motorcycles require special attention. DIY trimmer maintenance may initially seem like a difficult task, but most buyers quickly get used to following the recommendations listed below and addresses service specialists very rarely. Care requirements are such.

  • Gasoline for the engine should be clean, with an octane number not lower than 92. Fuel density-750-770 kg per cubic meter.
  • Two.Stroke engines are filled with a mixture of fuel and high.Quality oil in the proportions, which are indicated in the instructions for the operation of a trimmer for grass. Most often, one liter of gasoline accounts for 20, 25 or 40 ml of lubrication. The best oils are produced by the manufacturers of garden equipment. “Stihl”, “Husqvarna” and other brands.
  • When working with a four.Stroke engine, fuel and oil are poured into different tanks. Both containers should be filled to the upper mark.
  • Swing gasoline filter must be cleaned about every 10 hours of work: dirt, particles of mowed grass and bark of shrubs gets into it. It is necessary to ensure that it is saturated with oil. If cleaning does not bring results, the filter should be replaced with new.
  • From the spark plugs and muffler of the motor, you need to periodically remove the carpet

Reducer gears need lubrication, especially after replacing them, when slowing the spindle rotation, as well as when extraneous sounds appear during the work of the trimmer for grass. Lubricants for their products are produced by the manufacturers of motorcycle, but you can use universal, for example, lithol. How and how to process a specific model of a mower, it is better to know from the documentation to the device. Most often, manufacturers advise lubricating the gearbox once a year/season, oil in many models is poured into technological holes on the node.

Attention! Before lubrication, the gearbox should be cleaned of pollution.

Playing the lawn mower

The new trimmer for the grass is rolled up to make sure of its serviceability. The engine of the device must work for fuel and clock, details. Be worn to each other, and fasteners. Pass the test for the strength. This process is carried out as follows. It is necessary to start the tool and smoothly increase the speed, warming the motor, but at first it must be protected from overheating. Then you should open the throttle of no more than 2/3 of the possible stroke, and let the motor work idol for the first few minutes, and then try out on the soft grass. It is best to mow the lawn.

Attention! After test inclusion, the oil must be drained.

Preparation of a benzotrimmer for the working season

Before starting regular use of the lawn mower, you need:

  • Collect the device according to the instructions;
  • Prepare a new portion of the fuel mixture. For a two.Stroke engine;
  • Pour fresh gasoline and oil to the desired level. For a four.Stroke motor;
  • Change the spark plugs, clean or replace air and gasoline filters;
  • Adjust the carburetor (according to the instructions for the device);
  • Check the condition of the fasteners and, if necessary, tighten them;
  • Lubricate the gearbox.
  • Check the fishing line for the trimmer and nozzle.
See also  STIHL grass trimmer STIHL fs 38 line change

Preparation for wintering

So that the benzotrimer does not lose performance for the period of inaction, you need:

  • Inspect the device for the presence of cracks, chips, bent parts;
  • Disconnect the casing and cutting head;
  • Drain the fuel from the tank and turn on the device to develop the rest of the gasoline;
  • Wipe/rinse the bar, handle, casing thoroughly;
  • Remove the coil or knife;
  • Clean the gearbox and add oil into it;
  • Inspect and rinse filters.

Then remove the light of the ignition, pour a little (20 ml) of motor oil into the hole and smooth the engine shaft several times using the starter to distribute the lubricant along the cylinders. After these manipulations, you need to insert the candle back, but do not twist until the end. This procedure (except for the grade of oil) must be carried out once a month, until the device is used.

How to use a trimmer correctly

Garden trimmers for grass are effective. Newchers think that it is easy to work with a lawn mower, because you just need to include it in a socket or pour fuel, but this is not entirely like that.

The efficiency of the garden tool and its service life directly depend on operating conditions. Therefore, before using a trimmer for grass, you need to perform preparatory work.

The lawn with which you need to mow the grass is carefully examined. Be sure to remove glass and large stones. Having flew out from under a working mower, they can injure a person. They remove the wire from the lawn, because it can be wound on a rotating element, break a mower.

After that they move to the installation of the cutting system. There are trimmers for low.Power grass on sale, which use only a fishing line for a trimmer. It is designed for mowing juicy and soft grass. But there are models with a capacity of more than 1 kilowatts on which metal knives are installed. They cut sowing and other hard weeds, trim the young shrub.

In order to replace the cord with knives, you need to unscrew the mounting nut, install the cutting element. Then the nut must be returned to the place, tighten it with the key.

The operator must take care of his safety. Mow grass in tight protective clothes. Special glasses are used to protect the eyes, they will protect from dust, grass and flying garbage. Hands are covered with gloves.

The electric trimmer for the grass is included in the network, and the battery models are charged for several hours before starting operation. Fuel is poured into a gasoline mower.

Milwaukee M18 2823 Brushless Cordless 21″ Lawnmower

The mower is kept so that the spool or knife is located parallel to the ground. When the tool is installed in the correct position, the motor is included. After the grass is bewildered, the mower is turned off.

First start

Before the first launch, the operator collects a mower, the procedure is described in the instructions that are attached to the product.

If the trimmer for the grass is gasoline, it is necessarily checked before operation. The fuel tank is filled along the neck.

The motor should work for the fuel, so at the first launch it should work for several minutes without load. After that, start mowing grass.

How to refuel a benzotrimer

Motokos working on gasoline are with two.Stroke and four.Stroke engines. The first option is much more common. What are the differences between them:

  • In trimmers with a 2-tact engine, the response to press the inclusion lever is faster (for this reason the lawn mower is mainly equipped with this type of engine);
  • A tool with a two.Stroke engine will be much easier, as well as easier to maintain;
  • Fuel consumption in a two-stroke engine is higher than in a 4-stroke with a similar power by about 30%;
  • The 4x-stroke engine is more environmentally friendly, since the fuel in it burns completely and is not thrown into the atmosphere, as well as its noise level is much lower;
  • And the most important distinguishing feature is the refueling: a 2x-stroke engine is equipped with one common tank, where gasoline mixed with butter is poured; 4x-tacte has a separate gas tank and a tank for motor oil.

For refueling, it is necessary to use fresh gasoline AI-92 or AI-95 and high-quality motor oil for garden equipment (for 2x- and 4-tact engines, manufacturers produce different oil). Oil can be used mineral, semi.Synthetic or synthetic.

The proportion of gasoline and oil for trimmers with a 2x-tact engine can be found from the instructions for a specific model. Usually it is 50: 1, in some cases, proportions of 25: 1 or 40: 1 are recommended. Prepare the fuel mixture in a separate container with accurate observance of proportions. Never pour the liquids “by eye” directly into the tank without mixing them in advance. Detailed instructions for mixing a benzomalam, with video and description, can be found on our website here.

Running

Before starting operation, gasoline braids are necessarily rolled up. The operator turns on the motor, he must work for a while at idle. It is necessary to ensure that the engine does not overheat, the load should not be.

When running in, motorcycles increase the load gradually. If you start work with high speeds, the motor will work well, this will affect the further work of the mowing.

At the first launch, you should not fully develop a temporary resource. After the engine works at idle, you can proceed to processing the lawn. The lawn mower should operate for no more than 15 minutes, after which the engine is turned off, it must cool down.

If you need to run the electrimmer, the braid is first collected. Then make trial launches at least 3-5 times. If the engine works well, go to mowing. At first they work for no more than 5 minutes, then the duration of work is gradually increasing.

How to wear a belt

If the tool has a shoulder mount, before starting work it hangs on the shoulder. The trimmer for the grass is fixed on both shoulders if it has a backbone mount.

The model with a bicycle handle is held with 2 hands, the D-shaped handle is wrapped in palm. The belt must be worn so that it is convenient, then the back will not get tired.

How to cut the lawn so that it turns out to be even

So that the grass on the lawn is trimmed evenly, it is necessary to lower the mower as low as possible during operation. The site must be divided into squares. You need to work, moving clockwise. In this case, the hay will always lie on the left without interfering under the feet.

Kosim under hay

It is better to mow hay not with a fishing line, but a metal disk. Grass is cut under the root, maintaining its length as much as possible.

Spinning high grass

If you need to mow high grass, this is done in several suits. The lawn processes 2-3 times. The rotating part is lowered from top to bottom, in which case the grass is not wound on the reel.

The operator must remember that the grass wound to the coil leads to overheating of the motor. If this happened, the motorcycle is turned off, and the coil is cleaned.

Most effective mow grass with the ends of the fishing line, and not the entire length. In the second case, the tool works worse, engine overload is possible. If you need to cut the grass on the site of a large area, to increase the efficiency of a trimmer for the grass, you must be tilted towards the mowing.

| Denial of responsibility | Contacts |RSS