How to put on a fishing line for a trimmer for a trimmer for grass. Video

How to change a fishing line for a trimmer in a trimmer

Trimmer for grass is the most common unit used to cut grass and cut small shrubs. This device is distinguished by its simplicity in maintenance, simple management during operation, and even women cope with it even a small weight. It is no secret that for the high.Quality performance of herbal mowing work, the correct selection of a cutting tool is required. As the latter in trimmers, special cutting nozzles (wheels, knives) or trimmer heads with fishing line inside are used. Nozzles and a fishing line for a trimmer are a consumable tool, but if the knives can be sharpened, then when spending the fishing line you need to replace it. In this article, we will tell you in the most detail how to correctly replace the fishing line for the trimmer.

A mowing head for grass is a cylindrical case in which a coil (bobbin) is inserted with a fishing line in it (cord). This design can be installed both on gasoline and electric trimmer. The heads differ in the method of refueling and supplying the cord and there are 3 types.

  • Automatic. The cord is supplied after the user reduces engine speed. Although the automatic supply of the fishing line is convenient if large volumes of work are performed, such rods have one drawback. A large thread consumption.
  • Semi.Automatic. Using this type of head does not require complicated manipulations from the user. The principle of their operation is arranged so that the cord is automatically lengthened at a time when the device works at full speed. It is enough to slightly hit the trimmer’s head for the grass on the ground (this removes the cord lock), and the fishing line for the trimmer, due to the centrifugal force, moves out of the bobbin, after which it is cut to the desired length with a knife located on a protective casing.
  • Manual. For lengthening the cord, the device is required, after which the fishing line for the trimmer is handed out manually.

Based on the above, semi.Automatic bobbins are the most optimal option. It should also be borne in mind that the coils for a trimmer for grass are one.Built (used only to trim the grass) and two.String, which are used to mow high grass and small, with thin stems of shrubs.

How to replace a fishing line for a trimmer on a trimmer?

Replacing the fishing line for the grass with step.By.Step instructions will even allow the owner of the lawn mowed inexpensive in such matters to do a fairly difficult job.

However, before starting work to replace the fishing line on the trimmer, it is necessary to ensure the safety of work. In particular, it should be taken protection measures against careless or spontaneous inclusion of the lawn mower:

  • Exclude spontaneous start,
  • Delete the battery (if used),
  • Place the tool on a comfortable site for work.
fishing, line, trimmer, grass

It is convenient to perform work on replacing the fishing line for the grass when the lawn mower lies on the table, and the master, who is performed by replacing the fishing line of the trimmer for the grass, has the opportunity to approach the instrument from any side.

Remove the head of the head of the grass for the grass

At the first stage of disassembly, the head of the head of the grass is removed. On the example of the models of trimmers “Black and Decker” and others, it is usually enough to apply some pressure to squeeze the click-fixer, which are on the side of the head of the head of the head of the head of the head of the body to remove the lid to remove the lid.

Some models of lawn mowers initially include dismantling the head of a trimmer for grass, for which a playback key is used, which is included in the tool kit. The head is usually held by two or three screws, access to which is provided through the side holes of the rear decorative cover.

See also  gasoline grass trimmer how to remove the coil

Stihl trimmer aka weed eater, weed wacker overview

The head cover, where the coil with a fishing line is installed, is usually held due. It is enough for some effort to squeeze the tongue-thorough and slightly turn the lid, after which the lid is easily removed

At the time of squeezing the tongue-fixer, you need to turn slightly and raise the head of the head of the trimmer for the grass to remove the winding drum.

Step two: extracting a winding drum (coil) with a fishing line

The next step in the process is the exhaust drum with a fishing line from the inner region of the head. You need to turn the head with an open side to see a fishing line for a trimmer and a reel. On the side of the head, find two recesses (eyelets) through which the fishing line for the trimmer is bred outside.

You should release a fishing line for a trimmer from the holes by checking the drum. Then gently remove the coil from the head of the head. The winding drum of some models is installed on the spring. This moment must be taken into account by performing the operation to extract.

The procedure for extracting a coil of a trimmer for grass with a fishing line from the inner region of the head: 1. Head assembly with a coil; 2. Extracting neatly with a small axial turn; 3. Extracted details

The old fishing line for the trimmer is completely removed from the coil. To remove the old fishing line for grass, you need to remove the forest from the loops and pull the free end. This method is removed by the whole old winding. A similar process is repeated on the second section of the drum. The master is recommended to use gloves when performing work.

We carry out the winding of the fishing line

Sentlessly completed disassembly of a spray coil without losing its spare parts allows you to go to the main task-winding into a fishing line coil. Technological features of the design of the spool and the number of working antennae determine the sequence of actions.

fishing, line, trimmer, grass

Coil with one working osik

The easiest option and a simple sequence of actions:

  • The dimensions of the bobbin and the length of the original factory winding determine the length of the fishing line recommended for winding. 2 5 m.
  • One end of the fishing line is inserted into the fixing technological hole located inside the spool.
  • The fishing line for the trimmer is wound on the drum in reverse rotation of the spray in the trimmer product direction. As a rule, on the inside of the bobin, the arrow indicates which direction the winding is carried out.
  • A small section of the fishing line is left free to output it. It is fixed in a specialized border on the inside of the bobbin, designed to keep the winding when assembling a spool in working condition.
  • The left end of the fishing line is passed through the hole of the outer part of the bobbin.
  • Half of the bobbin are collected and put on the bar of the trimmer device.

Two working antennae

In this type of spools, the number of grooves for winding the fishing line lying on the inside of the coil should be determined:

For both cases, a fishing line for a trimmer 2-3 m long is taken. In a single.Captable coils, the fishing line for a trimmer stretches into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in the back of the rotation of the bobbin on the bar the side. Inside the arrow is usually indicated the correct direction of the winding. In the presence of fixing grooves, the ends of the fishing line are threaded in them or hold the fingers of the free hand, spread into the through hole of the outer half of the bobin, the spool closes and attached to the bar of the trimmer product.

The difference between the winding of the fishing line in the two-to-dancing coils is that initially a line of fishing line 2-5 m long is folded in half (to determine the middle fold), and the bend loop is inserted into a special groove between the grooves. Both strains of the fishing line are wound each in its own groove, fixing the antennae and assembly of the coil is similar to the option considered above with one groove.

The first implementation of this procedure may seem long and quite time.Consuming, but over time and experience, this task will be solved much faster and easier.

See also  How to choose the right disk for your grass trimmer

The video below will clearly show how to refuel a fishing line for a trimmer to the coil of a trimmer for the grass and correct it correctly. This operation is not a complicated one and, with some patience, will necessarily be crowned with success:

Engine’s type

On a trimmer for grass gasoline, 2 types of engines are installed: two- and four-stroke. The first cheap, powerful, but for refueling it is necessary to prepare a mixture of oil and gasoline of the A92 brand.

The second type is more expensive, but less “capricious”, they are installed on professional tools. They are 1.5 times more economical than two.Stroke analogues, work quieter, create less exhaust gases. Fuel is poured separately, the level of vibration is lower than in cheaper samples.

Cutting element

Grass cutting is carried out with a knife or fishing line. The first option is more effective. The knife copes with dense thickets of grass, branches, does not need to wind. Lack of knives is a high level of danger, the need to periodically tighten the tool. True, all models provide protective blocks, but they are installed from the operator.

Trimmer fishing line is safe, light, it does not need to sharpen it. Disadvantage of this type of cutting element. It is not intended for thick branches. For young grass, a fishing line for a trimmer 2 mm thick is used, for more rigid vegetation. A fishing line for a trimmer with a diameter of 3 mm.

fishing, line, trimmer, grass

The saw disk is used to cut the most hard branches.

The cutting disk easily copes with grass and small branches

There is a universal option with a change of cutting element. In such trimmers, a fishing line for a trimmer and a knife is changing, based on the task. The lack of such devices is a large price.

How to remove a fishing line for a trimmer

To replace a fishing line for a trimmer in a trimmer, remove the head cover. To do this, press the fingers of the latches of fixers located on both sides of the lid, and pull the lid up. Access to the coil will open. After that, pull it out, pulling up the axis on which the coil sits. If the ends of the fishing line stick out from the holes of the head, then lift the coil along the axis and pull the remaining fishing line from the holes of the head. Now the detail does not hold anything and it is easy to remove and remove the remaining working thread.

The coil is divided into two parts by the central partition with a neckline. Different models of cobs differ in size, so you need to check how much you can wind the fishing lines on the bobbin. Its length ranges between 1 and 4 m.

The choice of fishing line

In order to easily wrap a fishing line for a trimmer to a trimmer coil for grass, it is worth deciding on what tasks the garden tool will perform. The thicker the thread tucked into the head, the more difficult the tasks that it can complete. It should be noted that a universal thread is often used, the width of which does not exceed 2 mm. You, in turn, can decide on the size, using the following methods:

  • Get acquainted with the information set out in the instructions from the manufacturer;
  • Check the suitability of the fishing line for use on your own, trying to insert it into the coil hole;
  • Study the spool for information about diameters allowed for use.

Selection of fishing line for refueling a trimmer for grass can be carried out by engine type. So, for example, an overly thick thread can affect an increase in rotational resistance. Because of this, the load on the engine will increase, which will certainly affect the quality and timing of its further operation.

Avoiding negative consequences is easy. To do this, it must be borne in mind that for electric motors with a power of up to 500 W, a fishing line for a trimmer with a diameter of up to 1.2 mm is ideal. If you cannot get such a thread, you can use the cord by 1.6 mm. A thread with a diameter of 2 mm, in turn, is used for engines with a power of more than 1 kW. It is worth noting that the cord for 2 mm is often used for winding on a bent mower. If the gasoline device has a straight shaft, the thread should be used 2.5 or 3 mm. The thickest fishing lines are installed exclusively on devices, the power of which is equal or exceeds 1.3 kW.

See also  Can a pregnant woman mow with a trimmer?. What vitamins should be taken?

The last, but no less important factor is the type of fishing cross section. When choosing it, it is worth focusing on the tasks set before the garden tool. There are several demanded cross.Sectional options:

fishing, line, trimmer, grass
  • Twisted-has a small margin of safety, which is why it suits exclusively for young grass;
  • Substitute. Is characterized by sharp edges suitable for working on overgrown weeds;
  • Round. The most common section. Such fishing lines cope well with fresh grass, but they are not suitable for shrubs and dry ones;
  • Rectangular, square and star type of cross section-due to low strength, are used to work on lawns.

The most durable and universal cord is a two.Component fishing line for a trimmer with a round cross section, inside which the core is located. It is this thread that is suitable for the majority of work. It must be remembered that the use of fishing fishing line, ordinary wire and other third.Party materials as a cord pose a danger to others.

Where to begin

First of all, it is necessary to remove the head from the motorcycles and open it. For this, latches are provided on the sides of the case.

A spitter head of three main elements consists. The head with a spring, a coil, on which a fishing line for a trimmer is wound, and cover.

Before proceeding with the “dressing” of the fishing line, you need to make sure that it is suitable. To do this is very simple. We insert the end of the fishing line into the hole in the head, and if the fishing line for the trimmer passes into the hole without problems, then this diameter is suitable.

Tips and recommendations how to wind a fishing line for a trimmer and what you need to know

There are several useful tips and recommendations that it will be useful to find out not only beginners, but also experienced masters-codes. These tips will help prevent negative consequences in the form of injuries and improper functioning of the mechanism. These recommendations say the following:

  • Set the lid to clicks. Over, these are 2 or more clicks, which depends on the number of fixers. If one latch does not click, then when starting the tool, the drum can jump out and injure a person
  • Do not wrap a fishing line for a trimmer with its strong pulling, as well as in an amount more than you can insert it into place. It is better not to harvest the equipment than it will be more, as this will lead to negative consequences in the form of the impossibility of unwinding it if necessary
  • If you own the tool not with two conclusions of the fishing line, but with one (usually low.Power units), then the winding process is performed in a similar sequence, as described above, only with the difference in the absence of the average side between the extreme bases of the coil
  • After replacing the material, it is necessary to first check the tools of the tool, and then proceed to the mocking of the grass. If you do not make a preliminary check, then the forests can be unwound, and injure a person

It is interesting!Choose the material of the appropriate quality so as not to get injuries when working with benzo.Cards, trimmers and motorcycles. In the process of beating grass, small stones and other materials fall under the rotating parts, which can fly over long distances, therefore, despite the fact that the fishing line for a trimmer is not a knife, working with a tool should be carried out in protective special uniforms. The result of the work done is as follows. After the replacement of the new material is enough for an area of ​​up to 600 square meters, but when taking into account the presence of a reinforcing layer on the fishing line. Ordinary nylon materials serve less, which is important to take into account when working. Do not try to mow thick.Button grass with fishing line, as there are special metal wheels or knives for this.

Cheap and Effective Fishing Pliers Which Cut any Type of Line Like Through Butter [4K]


| Denial of responsibility | Contacts |RSS