How to put on a harness for a trimmer for grass. Belong belt Redverg

A belt for a trimmer for grass from China. Characteristic and design of the product, price, video

Working a trimmer is much more convenient and easier to use a special belt. Thanks to him, the operator can mow large sections of grass without pain in joints and muscles for several hours in a row. The design of the biceps belt is designed so that the lawn mower is kept using the mounts itself. Without the help of hands. She will only need to set the direction, and she will do everything else herself. About how to correctly attach a belt to a trimmer and set it up for yourself to facilitate the load, and it will be discussed in this material.

Most often, benzotrimers operate on two.Stroke gasoline internal combustion engines, which requires gasoline mixed with mineral or synthetic oil. Two.Stroke engines need the correct ratio of gasoline and oil proportions, so it is important to carefully study the instructions for your benzotrimer model before use. Convenient and silent models are trimmers for grass with four.Stroke engines, in which gasoline and oil are poured into separate containers, mixing inside the unit.

The internal combustion engine is located in the upper part of absolutely all gasoline trimmers.

For areas with rough vegetation, you need to choose a powerful gasoline trimmer for grass, the power of which will allow it to be used as a bitchcore, cultivator and even a snowman. There are two types of drives that rotate the cutting element of a benzotrimer. A steel cable and a straight shaft with a gearbox. It is advisable to choose an unit with a direct shaft, since it is more reliable than a cable regarding mechanical strength.

A belt for a trimmer for grass from China. Characteristic and design of the product, price, video

Hello! Well, soon the summer season will begin)) Sourcelessly without “mowing” on the site can not do. A neighbor in the country acquired a “ran” belt for its Khuskvarnna last summer, says that it is much more convenient than shoulder! So I decided to buy myself too, but so far I have not decided which one is better? There are just with “straps”, there are soft straps, there are some kind of casing. In general, if there are happy owners of the background belt, please advise the model and company. And in general, the opinion is interesting, is it necessary?

With my champion T514, this included. Support on both shoulders, plus soft lining under the lechi. The braid itself for grass is attached to the side and rests on a wide plastic plate. Result: a rather difficult braid for grass becomes very convenient to use. Hands are occupied only by lifting/lowering the head (almost without effort, if the hook is placed in the center of the corner of the bar) and turning left and right. I think the most convenient way of suspension of a trimmer for grass. Structurally, the Champions of Champions.

Last season, he drank a heavy Chinese scythe (42 cubes) with a standard shoulder belt. The shoulder was quickly tired, and the design itself is apparently not successful. For this season, I bought a Solo satchery belt until I mowed, but I pulled Motokos on it:. Much more comfortable. Having harvested very quickly, one big buckle on her chest is put on it and that’s it.

trimmer, grass, belong, belt, redverg

Someone visited the back of the back of the straps?

I tried this, according to it, distributes the weight more to the lower back than on the shoulders. We have the price in n.N. About 1 tyre. I can sell for 500 r.

Dima80 I set it up incorrectly, align the lower belts. The backpack is good, 4 hours of work, only the legs are tired.

I have already cut off such a suspension for 2 seasons, the braid for the grass is heavy, almost 8 kg. If you fit well, does not grate anywhere and does not press. Before that I used Hitachi, also good, comfortable. But Stilevskaya (from the 130th) personally seemed less convenient to me, the Germans saved on some trifles. I also tried the champions, that is generally liquid, no matter how you drive it. It hangs out. They wondered how to sew a comfortable suspension on his own. She sews bons professionally and all that, in short, understands how such things do. Well, in principle, you can sew, but there are a lot of muddy. The material will go off rubles at 300-400, special. Sewing machine is needed (or manually with a nameplate), and a free heap time.

How to wear a trimmer belt for grass correctly

Working a trimmer is much more convenient and easier to use a special belt. Thanks to him, the operator can mow large sections of grass without pain in joints and muscles for several hours in a row. The design of the biceps belt is designed so that the lawn mower is kept using the mounts itself. Without the help of hands. She will only need to set the direction, and she will do everything else herself. About how to correctly attach a belt to a trimmer and set it up for yourself to facilitate the load, and it will be discussed in this material.

A rug belt for a trimmer for grass-purpose

Many models of trimmers are equipped with an ordinary oblique belt. However, for work, it is best to purchase a rug belt, which is specially designed for motorcycle. Thanks to a thought.Out design, it evenly distributes the weight of the device for the whole body. The shoulders with a soft lining reduce the severity and relieve pain in the forearms. The hard back disperses the load between the upper and lower backs, excluding the lower back. The impact.Resistant protection for the thigh prevents the contact of motorcycles with the foot so that it does not rub and transmit vibration. In addition, the belt provides:

  • Convenient transportation of a trimmer for grass;
  • Comfort during operation due to the ergonomicity of the spit position for grass relative to the body;
  • Safety in work. The paraphernal belt prevents the slipping of motorcycles from the hands at the time of the stabs of hard objects.
See also  How to change the drum on a mower. Video: replacing the coil on the electrimmer

What is a rug belt

It should be understood that the weight of the seasoned motorcycles is an average of 6-9 kg. And this device must be kept in a limited state all the time. To evenly distribute the load, the backpack belt, as it were, encircles the body from all sides. The main load falls on the shoulders and back, so its upper part is complemented by wide foam inserts and tissue straps. Further belts are lowered along the body and with the help of a quick.Sitting clip are connected to each other in the area of ​​the chest or abdomen. And so that when loading, the belt does not crash into the body, a wide and durable lining is provided. Plastic protection for the legs is attached to the belt. It has a carbine for attaching to a trimmer and depreciation in the form of a spring. The ease of unfastening and fastening the motorcycles is ensured by a rapidly latent latch located on top.

On a note! Different models of the paramedic belts can differ among themselves by the design of locks, carbines, the presence or absence of additional linings and latches. However, the principle of the device and operation is the same.

Belt setting

To ensure the conditions of comfortable work, you need to be able to wear a rug belt correctly. This process requires a certain dexterity, but then, after adjusting the satchel for itself, it will be much faster and easier to worry.

Hook height adjustment

The most important thing is to adjust the belt so that the trimmer for the grass is at the right level from the surface of the earth. To do this, raise or lower the height of the hook, which is carried out by pulling the shoulder belts until the holder is lower than the hips by 10-15 cm (palm width). In this case, the knife of the attached braid for the grass should be parallel to the surface, that is, in a strictly horizontal position.

On a note! If the trimmer for the grass is attached too high, then this will greatly limit the capture of the grass.

Bowling braids for grass by moving the ears

After fixing the necessary heights under yourself, you need to balance the trimmer for the grass. To do this, the ear is rearranged, with which the device is suspended to the belt, forward or backward. As a result, you need to attach the belt to the trimmer so that when the steering wheel is released, the knife or saw disk does not lie on the ground, but hung above it without touching the surface. At what distance will it be dependent on the goals set.

How to dress a motorcycle

Redverg 5014460 Belong belt for hanging a trimmer for grass. With the protection of the thigh. Bought for a chamber for Champion grass

Small video about kosba by a benzotrimer / benzocosa on the example of a student: how to dress a belt, like a balancer.

Electric trimmer for grass with the upper engine location (Stiga)

Using such a trimmer for grass, you can successfully fight weeds and mow everything, up to swan, burdocks and shrubs. The release of the fishing line here is semi.Automatic or manual, the diameter of the fishing line is from 1.6 to 2.4 mm.

The undoubted advantage of this category of trimmers is that now you can safely mow and raw grass without afraid to get moisture on an electric engine. However, in no case should you mow during the rain!

Battering trimmers for grass are also not very noisy, they are easy to run and stop, you can freely move along the lawn, but the shortcomings are low cutting, larger weight (up to 4.5 kg) and a short time without recharging. From 15 to 30 minutes. Therefore, they still do not find wide application.

Gasoline trimmers for grass are widely used due to their autonomy, high power and performance. It is these devices that are most often used by professionals in their work.

trimmer, grass, belong, belt, redverg

When using a gasoline trimmer (benzocosa), you do not need to worry about the presence of a network outlet and the quality of the network voltage, be afraid to accidentally cut a cable-purple or melt their landing.

According to the layout of the lawn mower (however, partly this applies to electric trimmers) differ among themselves:

  • Engine power and type (two.Stroke or four.Stroke);
  • A rod shape (straight or angular, solid or detachable);
  • The shape of the control handles (D, J or T-shaped);
  • Cutting tool (trimmer head, disc knife).

The braids for grass with a four.Stroke engine are favorably different in that gasoline and oil are poured into the engine, as in a car. Separately. The preliminary preparation of a two.Stroke fuel mixture from gasoline and oil is not required.

Motos maintenance

For trimmers and electricity with a curved bar, everything is simple. It is only required to change the fishing line for the trimmer. For the served gearboxes, about once every 50 hours or once a year, you need to turn off the screw and add consistent grease. In the lawn mower, everything is reduced mainly to servicing the engine itself. Periodic cleaning of the air filter. Usually you just need to remove the filter, blow (sometimes soak with oil) and put in place. About once a year (or with a noticeable reduction in power), you need to check the condition of the fuel filter. It is in the tank, you can get it using a curved wire. Most often after purging the filter can be set back. If there is a sparkle in the muffler, it also needs to be cleaned from time to time.

See also  How to improve a trimmer for grass for grass. Waited for problems with the spark plug

If the engine works on a mixture of gasoline and oil, after work you need to drain it from the tank, start a braid and wait until the motor develops the rest. Pure gasoline engines do not require fuel drainage.

Putting ECHO Shoulder Strap On

But the most important thing is cleanliness. Any braid must be cleaned after work. And not only the zone of the cutting tool in which the “porridge” accumulates from the remains of the grass, but also the ventilation holes of the engine. The gasoline machines are added to this list of cylinder cooling ribs. If you do not clean them, then over time a peculiar “fur coat” grows from a mixture of dust and dried scraps of grass, which sharply worsens the removal of heat. So the neglect of the “hygiene standards” in this case may be fraught with overheating and the failure of the engine. And this, recall, is the most expensive part of the lawn mower, and its repair can fly into such a penny that it is easier to buy a new tool.

Warning

Before starting work, it is necessary to take care of nutrition for your buzzing. As a rule, garden trimmers have a very small tail, requiring the connection of the extension cord. It is important to properly place a coil with a cable so that it does not interfere with work while driving. It is worth showing special attention when using steel knives, which can be damaged by a braid. The length of the cord should be enough for the end of the site, the cable should always stay behind. If the cord is too short, the stops due to pulling the shtepsel from the outlet are inevitable.

So that the cord does not get confused and does not cling to the bushes, you can use the extension cord.

How to use a trimmer correctly

Garden trimmers for grass are effective. Newchers think that it is easy to work with a lawn mower, because you just need to include it in a socket or pour fuel, but this is not entirely like that.

The efficiency of the garden tool and its service life directly depend on operating conditions. Therefore, before using a trimmer for grass, you need to perform preparatory work.

The lawn with which you need to mow the grass is carefully examined. Be sure to remove glass and large stones. Having flew out from under a working mower, they can injure a person. They remove the wire from the lawn, because it can be wound on a rotating element, break a mower.

After that they move to the installation of the cutting system. There are trimmers for low.Power grass on sale, which use only a fishing line for a trimmer. It is designed for mowing juicy and soft grass. But there are models with a capacity of more than 1 kilowatts on which metal knives are installed. They cut sowing and other hard weeds, trim the young shrub.

In order to replace the cord with knives, you need to unscrew the mounting nut, install the cutting element. Then the nut must be returned to the place, tighten it with the key.

The operator must take care of his safety. Mow grass in tight protective clothes. Special glasses are used to protect the eyes, they will protect from dust, grass and flying garbage. Hands are covered with gloves.

The electric trimmer for the grass is included in the network, and the battery models are charged for several hours before starting operation. Fuel is poured into a gasoline mower.

The mower is kept so that the spool or knife is located parallel to the ground. When the tool is installed in the correct position, the motor is included. After the grass is bewildered, the mower is turned off.

First start

Before the first launch, the operator collects a mower, the procedure is described in the instructions that are attached to the product.

If the trimmer for the grass is gasoline, it is necessarily checked before operation. The fuel tank is filled along the neck.

The motor should work for the fuel, so at the first launch it should work for several minutes without load. After that, start mowing grass.

How to refuel a benzotrimer

Motokos working on gasoline are with two.Stroke and four.Stroke engines. The first option is much more common. What are the differences between them:

  • In trimmers with a 2-tact engine, the response to press the inclusion lever is faster (for this reason the lawn mower is mainly equipped with this type of engine);
  • A tool with a two.Stroke engine will be much easier, as well as easier to maintain;
  • Fuel consumption in a two-stroke engine is higher than in a 4-stroke with a similar power by about 30%;
  • The 4x-stroke engine is more environmentally friendly, since the fuel in it burns completely and is not thrown into the atmosphere, as well as its noise level is much lower;
  • And the most important distinguishing feature is the refueling: a 2x-stroke engine is equipped with one common tank, where gasoline mixed with butter is poured; 4x-tacte has a separate gas tank and a tank for motor oil.

For refueling, it is necessary to use fresh gasoline AI-92 or AI-95 and high-quality motor oil for garden equipment (for 2x- and 4-tact engines, manufacturers produce different oil). Oil can be used mineral, semi.Synthetic or synthetic.

The proportion of gasoline and oil for trimmers with a 2x-tact engine can be found from the instructions for a specific model. Usually it is 50: 1, in some cases, proportions of 25: 1 or 40: 1 are recommended. Prepare the fuel mixture in a separate container with accurate observance of proportions. Never pour the liquids “by eye” directly into the tank without mixing them in advance. Detailed instructions for mixing a benzomalam, with video and description, can be found on our website here.

Running

Before starting operation, gasoline braids are necessarily rolled up. The operator turns on the motor, he must work for a while at idle. It is necessary to ensure that the engine does not overheat, the load should not be.

When running in, motorcycles increase the load gradually. If you start work with high speeds, the motor will work well, this will affect the further work of the mowing.

See also  How to put a disk on a gas station. A knife installation algorithm for a trimmer for grass

At the first launch, you should not fully develop a temporary resource. After the engine works at idle, you can proceed to processing the lawn. The lawn mower should operate for no more than 15 minutes, after which the engine is turned off, it must cool down.

trimmer, grass, belong, belt, redverg

If you need to run the electrimmer, the braid is first collected. Then make trial launches at least 3-5 times. If the engine works well, go to mowing. At first they work for no more than 5 minutes, then the duration of work is gradually increasing.

How to replace string trimmer edger line

How to wear a belt

If the tool has a shoulder mount, before starting work it hangs on the shoulder. The trimmer for the grass is fixed on both shoulders if it has a backbone mount.

The model with a bicycle handle is held with 2 hands, the D-shaped handle is wrapped in palm. The belt must be worn so that it is convenient, then the back will not get tired.

How to cut the lawn so that it turns out to be even

So that the grass on the lawn is trimmed evenly, it is necessary to lower the mower as low as possible during operation. The site must be divided into squares. You need to work, moving clockwise. In this case, the hay will always lie on the left without interfering under the feet.

Kosim under hay

It is better to mow hay not with a fishing line, but a metal disk. Grass is cut under the root, maintaining its length as much as possible.

Spinning high grass

If you need to mow high grass, this is done in several suits. The lawn processes 2-3 times. The rotating part is lowered from top to bottom, in which case the grass is not wound on the reel.

The operator must remember that the grass wound to the coil leads to overheating of the motor. If this happened, the motorcycle is turned off, and the coil is cleaned.

Most effective mow grass with the ends of the fishing line, and not the entire length. In the second case, the tool works worse, engine overload is possible. If you need to cut the grass on the site of a large area, to increase the efficiency of a trimmer for the grass, you must be tilted towards the mowing.

How to put a belt on a trimmer for grass correctly

The main technique

The cutting tool rotates counterclockwise, therefore, in practice, the working course (swing) braids for grass are most often performed from right to left. The advantage of this method: mowed grass falls on an already mowed surface.

The main technique when running high grass

With very tall grass or stiff, weapons are recommended to mow in two approaches: we cut the upper half of the plants on the wave, at the reverse move. Lower. Mowed mass and in this case lies on the left.

Internal characteristics

Most often, benzotrimers operate on two.Stroke gasoline internal combustion engines, which requires gasoline mixed with mineral or synthetic oil. Two.Stroke engines need the correct ratio of gasoline and oil proportions, so it is important to carefully study the instructions for your benzotrimer model before use. Convenient and silent models are trimmers for grass with four.Stroke engines, in which gasoline and oil are poured into separate containers, mixing inside the unit.

The internal combustion engine is located in the upper part of absolutely all gasoline trimmers.

For areas with rough vegetation, you need to choose a powerful gasoline trimmer for grass, the power of which will allow it to be used as a bitchcore, cultivator and even a snowman. There are two types of drives that rotate the cutting element of a benzotrimer. A steel cable and a straight shaft with a gearbox. It is advisable to choose an unit with a direct shaft, since it is more reliable than a cable regarding mechanical strength.

STURM Benzotrimmer 1500 W, disk, milling cutter BT8952D

Sturm BT8952D benzotrimmer-has a reliable 2-stroke internal combustion engine with air cooling. Working volume of the motor 51.7 cubic meters.Cm, developed power. 1500 watts. Usual in management and maintenance, the most powerful in the line of benzotrimmers Sturm! Household. Can be used in utilities or forestry. The real “combine” by the span of grass at least some stiffness, weeds, even a undergrowth. Automatic coil with a fishing line (a line of fishing line is 2.4 mm), a 3-lobed knife or a 40-set mill with carbide attacks is installed. Thanks to a reliable iron gearbox, a trimmer for grass can work without overheating. To facilitate the launch of a cool motor, a manual swimming pump is used (primer). A flat indispensable rod increases the reliability and lifespan of the tool (there are no compound elements subject to wear). A hard drive shaft makes it possible to use a knife or cutter in the work. The fishing line for a trimmer was created to work with a soft low grass, the knife allows you to mow hard grass and weeds, the use of a 40-tobinal cutter makes it possible to draw a shrub, remove unnecessary young shoots, branches, branches and trees with a dialect up to 50 mm.

To protect the user from those flying out from under the cutting part of small objects, the Sturm lawn mower! BT8952D is armed with a strong casing. By pressing the mowing head on the ground, the fishing line is served, excesses are cut off by a special knife on the casing.

trimmer, grass, belong, belt, redverg

Fishing coil (Ø 2.5 mm). Metal. Knife (three blades). A saw disc with 40 teeth with carbide attack. Plastic protection for gearbox.Key set for assembling the device. Two support pens. Consistency bottle (600 ml): Fuel oil. Shoulder belt (with a plastic lining on the hip). Engine (two.Stroke). Rod. 165 cm)

| Denial of responsibility | Contacts |RSS