How to remove a small screw without a screwdriver

  • Hammer in an oversized Torx bit. Tried
  • Make a slot in the head of the screw for a flathead screwdriver. Done, started to unscrew, also to no avail
  • Grind the edges of the bolt head with a file for a socket wrench
  • And the most annoying and extreme method. is drilling out.
  • Using a knife to drive out a Phillips head screw.
  • Using an old CD.
  • Sawed a long groove in the screw head.
  • A Phillips head screw can be tried with a flathead screwdriver.
  • Flat head screws

Step by step instructions on how to make an impact screwdriver

To make a home tool with their own hands, you need to stock up on starter motor from the car. Perhaps the part is lying around in the garage. Begin transforming the starter into a useful screwdriver for the house, focusing on the drawings and diagrams below. Follow this guide:

  • Separate the part of the rotor shaft where the winding is fixed.
  • In the part that remains, remove unnecessary components. The shaft and sleeve should remain. They act as a single mechanism.
  • The handle is made from a tube. Place the sleeve in the tube, but only at one end. In the other side put a plug. This will become the impact heel. For the end cap a large bolt will do. It prevents the tube from changing on impact and limits the sliding of the shaft on the inner surface of the sleeve.
  • Next, weld the parts together.
  • At the end of the shaft construct a square shaped shank. This seemingly insignificant detail will allow you to change one nozzle for another. If you plan to unscrew fasteners, a bit is fastened in the head. A different tip is needed for disassembly.
  • Arm yourself with an angle grinder when you start cutting the starter motor. Other equipment with low power will not take high quality steel.

How to remove small stripped screws | stripped laptop screws | stripped phone screw removal

To extend the life of the homemade implement, regularly apply an even film of lubricant to the splines. Be careful when using the attachment. Hitting the heads with a hammer too hard can damage the tool.

A clear video instruction on how to make an impact screwdriver with your own hands is shown below:

Preparatory steps

Any problem is better prevented than solved. Therefore, if you have applied sufficient force and the fastener does not move out of place, do not continue until you finally damage it. It is better to do the following:

  • First you need to remove the layer of rust and other dirt. If the threaded part protrudes over the parts to be fastened, clean it with a metal brush.
  • Take a hammer and tap the head. Shocks should be quite strong. It is all right if you make small dents in the metal, but you should not bend the fastener itself. This procedure contributes to the violation of the integrity of the oxides, so the positive effect will be only at the initial stage, when the head is pressed against the part. After you ripped the bolt from its place, it is not recommended to knock on it, since there is a high probability that you will damage the threads, thus complicating the situation even more.
  • Heating the fastener place gives very good results. All you need to do is heat the fastener and wait for it to cool. This burns out some of the substances, the rust is destroyed and the bolt can be unscrewed with less force. The heat needs to be intense. It can be done with a blowtorch, gas torch or acetylene torch. In all cases an open flame is used, so first make sure that you will not damage the surrounding elements. Do not forget about the safety rules!
  • Lubricate the hardware with any easy-flowing liquid. It can be a special compound such as WD 40, kerosene, or brake fluid. Their peculiarity is that they penetrate into all pores and crevices, lubricate the threads, and some destroy the rust. It takes some time for the positive effect to be felt. It is usually recommended to wait about an hour and then start working. In complicated cases, you need to wait 10 to 12 hours.
See also  What to do if you don't have a screwdriver

The above actions will also not be superfluous when you decide how to unscrew a bolt with a torn edge.

Screw Varieties

To begin with, a screw is a cylindrical rod with a special head, to which the screw groove is applied. Screws are produced according to a number of normative documents, including GOST 1144-80, GOST 1145-80, etc. д.

At the same time, there are two main types of metalware are:

For the designation in this case the diameter and length of the screw (for example, a product with a diameter of 5 mm and a length of 3.5 cm will be referred to as 5×35 mm). In addition, hardware can be classified according to the shape of the slot and the features of the head itself:

All of these varieties are made with a Phillips, straight (flat) and Torx (the latter is also known as a star) slot, as well as with an internal hexagon and other, less popular variants. There are also self-tapping screws with the head of the six- and octahedral shape (roofing), which are also made with different slits.

And on a side note! Screws also are divided into several varieties by thread type, which is primarily determined by the connected materials and the specific purpose (metal, wood, drywall or small appliances).

Take the tourniquet. Put the tourniquet under the screwdriver or the bit and push it into the slotted head. Then with simultaneous pressure and rotary motion try to remove the screw. With a properly applied force it is possible to unscrew a screw with a considerably screwed-in force.

Another option is to use a toothbrush. Melt one end with a lighter, and then immediately insert it into the recess on the head of the screw. After waiting a little so that the melted plastic hardens, turn the brush counterclockwise. Of course, it doesn’t help if the screw is screwed too tight.

See also  Installing the zilow compressor on the engine d 240

How to remove small screws without a screwdriver

No screwdriver at hand, you need to unscrew some screws and screws, how to do it without a screwdriver.

Here it all depends on what slits (slots on the head) on the screw or screw, as well as how hard and how deep it is screwed.

If the head is over the surface, you can use pliers, grab the head of the screw with the pliers, bring the “jaws” together and unscrew counterclockwise.

If you can’t get a grip, you can unscrew the screw with a knife, but a knife with a round rather than sharp end is better, like this

Instead of a knife, you can use a CD if the screw is not too tight, you can unscrew it with your fingernail, a plastic bank card, you can use a coin, or a metal ruler, a metal hacksaw blade, and.т.д.

If the screw is a Phillips screwdriver, you need a knife with a sharp end.

Insert the knife in the slits, press a little and unscrew counterclockwise.

If it is not possible and there is a drill with reverse, it is possible to buy a left-handed drill.

Switch the drill to reverse rotation, insert the “left” drill bit, apply pressure, the screw is unscrewed by the drill bit.

You can use an extractor instead of the “left” drill.

But all these tools are much more expensive than a screwdriver.

If the facets are flattened, you can make a slot with a hacksaw blade for metal.

If the screw plus all that is tightly “seated”, you can use a soldering iron tip to heat the head a little and then unscrew clockwise.

You can drop a few drops of kerosene, or brake fluid, or penetrating liquid, wait a little and you can unscrew the screw.

There were times when I was a child and actively tried to dismantle their toys and household appliances, well, I had a weakness, until I do not know what’s inside will not calm down and often such interests ended with the breakage of household appliances and toys.

So then I had no screwdrivers, but there were scissors which were in a box with thread and needles, and with the help of their sharp ends I managed to unscrew even screws and self-tapping screws of most different size and variety of heads.

Yes, I do not dispute that they are not modern scissors of soft steel and plastic handles, but they are fully metal and strong, they did not even bend, when I unscrewed wooden columns from the lighthouse and drawers of the table, opened cabinets and dismantled toys, they had no mercy on their ends fit tightly into the screw cross, and put together they unscrewed screws with straight grooves, and inserted a spoon into the rings of handles strengthened the leverage and I succumbed to much.

remove, small, screw, screwdriver

Even now sometimes I use scissors, not to run after a screwdriver, for example, I recently tightened the fixing bolt of a decorative trim on the door handle.

See also  How to cut aluminum at home

Using screws to fix any items. it is convenient and reliable. But sometimes you need to unscrew a screw in a hurry, and there is no suitable screwdriver handy. Of course, using a screwdriver is the simplest and safest method, but if necessary, you can do without it as well. How to remove a screw without a screwdriver? Today you will learn how to!

Another option is to use a toothbrush. Melt one end with a lighter, and then immediately insert it into the cavity on the head of the screw. After waiting a little bit for the melted plastic to solidify, turn the brush counterclockwise. Of course, it doesn’t help if the screw is screwed too tight.

  • Phillips head screw.
  • Using a coin to drive out a screw.
  • You can try to remove a screw with your fingernail.
  • Using a knife to drive out a Phillips head screw.
  • Using an old CD.
  • Saw a long groove in the head of the screw
  • You can try to remove a screw with your fingernail.
  • Using a knife to unscrew screws with a Phillips head screwdriver.
  • Using an old CD-ROM.
  • Saw a long groove in the head of the screw.
  • You can try to unscrew a Phillips screw with a flathead screwdriver

How to fix a bolt in glasses Take pliers, and cut off a small piece of paper clip with a knife (or metal scissors), insert the wire into the socket of the lug, and bend well with pliers. This will help temporarily use the glasses with the lost screw until a new one can be found.

remove, small, screw, screwdriver

Another option is to use a toothbrush. Melt one end with a lighter, then immediately insert it into the recess on the screw head. After waiting a bit for the melted plastic to solidify, turn the brush counterclockwise. Of course, this won’t help if the screw is screwed too tight.

How to unscrew a screw in your laptop that won’t unscrew

You can drill out the screw with a drill or electric screwdriver. I have an electric screwdriver, but I decided to try a third option. The third option is to make a notch along the head of the screw and unscrew it with a flathead screwdriver. I did so.

| Denial of responsibility | Contacts |RSS