How to remove the bobbin from a grass trimmer

Universal heads for brushcutters and what’s best to choose

The above options allow you to understand what type of brushcutter head is preferable. If you have money, it is better to choose the automatic models, and if funds do not allow to buy a good brand grass trimmer head automatic type, then you should choose from the segment of semi-automatic.

When choosing a coil for your tool, you can learn that manufacturers, in addition to branded devices, produce more universal, that is, such that can be used in conjunction with different models of trimmers. This is convenient only in one case, if you have two or more tools for mowing grass from different manufacturers.

A number of advantages of universal reels should include:

  • Suitable for most trimmers and chain saws from different manufacturers
  • Low cost, but they are not particularly reliable, so their selection requires a special approach
  • Prevalence. if it is quite difficult to find a branded reel for a particular model of grass trimmer, then with universal models there are no such problems

How to Remove the Cover from a Grass Trimmer

Since the choice of trimmer for grass we looked in the previous article, now we will tell you how to correctly fill the trimmer for grass fishing, and what better to choose based on the criteria of work.

Once you have purchased a trimmer for grass and began to use them intensively, at some point will raise the question of replacing the line, as it is the most wearing element in the tool, the intense use of trimmer for grass will lead to frequent substitution of consumables.

What types of lines are

A common type of fishing line that fits virtually all types of spools is the round section cord. It is an ordinary line, applicable to mowing succulent grass, but to mow dead grass with it will be much harder, and much less she can not cope with shrubs.

Usually the cross section to mow young grass does not exceed 1.6 mm. How to replace, remove the mower how to replace the grass trimmer head with a mower cutter. The most wear and tear element in the design of a grass trimmer with shrubs. How to remove this one at all. The thicker the thread, the rougher the grass it can cut.

There is a line with sharpened edges in the form of a star or a square, such a version is more adapted to mow dry grass just by having a sharp edge, but the disadvantage is its greater wear and tear, and on the strength it concedes round cord.

There are lines with improved aerodynamics with appropriate indentations, scales and notches, a similar product makes less noise, but use it only on benzosokosa, since the output of such thread from the spool is difficult, using it in most cases with discs, which are inserted segments. The disadvantage of such a product is its fragility.

In most cases, in gasoline trimmers with an engine capacity of more than 1.5 liters.с. cords with an iron cord inside are used. Such a thread is perfectly suited for mowing dry grass and small bushes. The wire core has a positive effect on the abrasion resistance of the material. The disadvantage of this cord is its price, which is significantly higher than the above-listed opponents.

See also  Grass trimmer gives gas and stops the reason

How to Disassemble a Grass Trimmer Reel. How to change lines on a trimmer.

This video shows how to disassemble the coil in a gasoline grass trimmer, as well as how to correctly reel.

Changing a line on a brushcutter.

How to wind the cutting filament on the brushcutter reel (grass trimmer)

How to tuck the line into the grass trimmer spool

It takes about 10-15 minutes to wind the line. How to Disassemble a Grass Trimmer Spool How to Disassemble a Grass Trimmer Spool After that, remove the protective cover and. What is a grass trimmer reel?? A plastic body with a cassette inside, which has a special hook for easy winding of fishing line. Almost all trimmer reels have a similar fastening principle, this is the central screw-button, when you press it, it is possible to pull the line of the required length. The photo below shows several examples of different trimmer reels.

Bobbins trimmers, the motor which is located at the ground, have a different attachment to the axis of rotation, they have on the spool two buttons located on the sides, which should be squeezed, otherwise the replacement thread is no different from other cassettes.

The principle of reeling in the line is similar in all of the above cases, so let’s take the standard version with two clamps as an example.

To remove the spool with the line necessary to unscrew the screw, located in the center, but note the thread is left, so you have to twist clockwise, it is done on purpose, so that during the work it has not opened under the influence of centrifugal force.

Next, using a screwdriver, dismantle the head and take out the spool, which is directly wound into a fishing line. Measuring the required length and folding it in half, you need to tuck the line into the spool, eventually bringing its ends opposite each other (there are special slots for fixing this).

After that it is necessary to assemble the head in the reverse order, passing the ends of the cord through the two corresponding holes.

If there are any doubts, or it is not quite clear how to charge the line on the grass trimmer, we recommend to see how to wind the line correctly in the lawnmower. In this video, the instructor will open the trimmer head step by step, measure the necessary amount of line, usually two to four meters, and demonstrate the assembly and installation on the trimmer for grass.

How to remove the bobbin from a grass trimmer

Most often, trimmers use fishing line, as it is a safer material to use. But if there is a thicket of bushes, young trees with the thickness of the trunk in a few centimeters, very high grass, you will have to use metal knives.

Metal blades can be bladed or serrated. Blades can have from one to eight blades, toothed ones. up to 80 teeth per disc. often, paddle blades have less weight and are used on low-power trimmers. Disks are heavier, to reduce their weight, peoria. holes over the entire area of the disk are used. The weight of the blades also depends on their thickness, which ranges from 0.8 to 2 mm. the thicker they are, the more reliable and longer lasting they are, but the load on the cutting assembly increases, and can cause tool breakage.

Blades with a thickness of 1.6 to 2 mm are used on very powerful professional machines. Carbide tipped discs are used to increase reliability. Solid discs are 1.5-2 times heavier than perforated discs, but are very good for haymaking. Due to their weight, they are fitted to lawnmowers with an engine capacity of more than 40 cc.see. discs with 16 to 32 teeth are best suited for cutting thick-stemmed plants (e.g. reeds). Perforated discs are good for cutting grass of any stiffness and trees up to 7 cm in trunk thickness and they pick up speed faster than solid discs.

See also  How to set the ignition on a trimmer

Grass trimmer with any metal knives are afraid of colliding with hard obstacles: stones, buildings, fixtures, etc.д. At such a collision blunt and deformed blades, the engine overheats, the gearbox can fail.

  • Manual. Cord length is extended by manually pulling it out, which requires a work stoppage. Requires a certain amount of skill, but presents no problem over a long period of use.
  • Semi-automatic. Cord comes out by itself, but needs to touch ground with bobbin head. No need to stop the engine or any special skills.
  • Automatic. Line is fed automatically at reduced engine speed. High cost and increased filament consumption.

Quick-reel (or non-disassembled) trimmers do not need to be removed from the base. New line ends are fed into the filament reel and then wound up several times. Remains are trimmed and the grass trimmer is ready for use.

The demountable ones need to be removed from the base, disassembled, remove old cord residue, wind on new cord, reassemble the head, install on the grass trimmer. The reels for winding the cord, located inside the bobbin, come in:. Single section, where both parts of the line are wound together;. two-sectional, when the spool is divided into 2 parts, and each end of the line is wound on its section. This separation reduces tangling and sintering of the line after encountering obstacles and sudden braking.

Instructions on how to wind up the line on the grass trimmer reel

Here are the steps of winding the monofilament fishing line on the bobbin of the grass trimmer:

  • The end of the line from the reel is pulled into the skipping rings of the finished tackle.
  • Open the line deflector.
  • Using any fishing knot tie one end of the monofilament to the bobbin.
  • Turn it a few times by hand while moving the bobbinwheel.
  • The winding can now be carried out with the help of a crank.
  • When the winding is accomplished, you need to close the fishing line.

Stihl Line Trimmer- How to Quickly Exchange the Head in 20 seconds.

Another method is to slip the bobbin and line onto a stick so that it can turn freely around its axis. Next, wind it on the bobbin of the grass trimmer. Here it will not be quite convenient to reel one, it is better to enlist the help of a friend.

As for the winding of braiding, it is necessary to perform the following actions:

  • Dip the prepared bobbin with braiding into a container of warm water, or at least into the water of a river or lake, right on the spot.
  • Now you need to implement the winding. Due to the more or less softened fiber, the line will lie and wind up quite evenly and tightly.

Filling the bobbins with thread of different types of bobbins

It should be noted that there are several types of reels for fishing tackle:

For each type of spool is designed for a different diameter of fishing thread. If the thread is thicker, it will not be able to be tucked into the spool. There will also be difficulties if you will use, for example, too thin monofilament, not intended for the filling of a particular spool.

In the case of the bobbin winding, one of two well-known methods is used:. Cross-winding;. Parallel winding, i.e. thread after thread is laid parallel to each other.

Now for the multiplier bobbins. Multiplier bobbins are a subspecies of inertial. Many fishermen make the same mistake, they tie the end of the line by the farthest hole of this element. This is not the right way to do it, it is worth tying only for the closely spaced holes.

How to remove spool head on EGO 56V string trimmer

See also  Gasoline to oil ratio for STIHL grass trimmers

Fishing threading of the multiplier spool takes place according to the following scheme:

  • First, the monofilament is secured to the body of the bobbin.
  • Next, you need to attach the reel to the spinning and pass the free end of the line through the right ring.
  • Tighten the device that protects the tackle from fish jerks.
  • Tighten the axle brake.
  • Now you can reel, guiding the line and thus controlling it.

How to remove the spool from the grass trimmer?

To prevent the assembly process from being long and tedious, it is best to put the elements of the unwound mechanism in order. This prevents tangling.

Here is the procedure for disassembly:

  • Unscrew the friction nut.
  • Next you need to unwind all the small washers and gears.
  • Handle must be removed.
  • You need to disassemble the spool mechanism.
  • Rotor removed
  • Now the swath roller is disassembled.
  • Next, the spool is removed.

Types of lines for lawnmower/grass trimmer

At the moment there are a lot of different kinds of cords. The line differs not only in diameter and length, but also in material, surface structure and cross-section.

But the main criteria for selecting a fishing line are:

How to replace string trimmer line

Almost always the main parameters of the line are marked on the spool reel itself. In this case, many manufacturers indicate the parameters of the line is not the exact value, but a range. For example, let’s take a reel with the following parameters: length. 2.5-3.5 (m), thickness. 1.5-3 (mm). The range makes the lawnmower more versatile. The wider the range, the greater the range of work the mower will be able to do.

When choosing a fishing line for a grass trimmer, it is especially important to consider the value of the diameter. As the diameter of the line increases, so does its strength. A good thick 3-4 (mm) line can be used for mowing already formed and hardened weeds. A thinner line of 1.5 to 2.5 mm is better for mowing young growth.

The diameter of the line is directly linked to the power of the mower. Thicker line is good to use only on high power, high output mowers. Usually a 3-4 (mm) cord is used on lawnmowers with an engine power of 1000-1200 (watts) or more.

Regarding the length of the cord, the longer the cord, the less you have to reload the reel. How else to classify brushcutter lines.

Section and surface structure

A classic of the genre is a line with a circular cross section. A cord with a rounded section is very robust and durable. But a rounded section is only good for mowing young growth, especially thin stems.

remove, bobbin, grass, trimmer

If the operator is faced with the task of mowing well established weeds with thick stems, and maybe even dead wood, then the rounded section of the cord will be ineffective in this case. A line with a sharp edge is well suited for these applications:

Of course, these lines also have their disadvantages. The main disadvantage of a serrated filament is its tendency to wear out quickly. Sharp edges tend to break intensively. The material of the line should also be taken into account when choosing a line. Linear versions of cord are made of plastic. Higher-priced lines are made from stronger synthetic material.

STIHL electric brushcutter: Features, tips for choosing and using

STIHL gardening technology is well established on the market. Electric grass trimmers of this company are distinguished by quality, reliability, stable operation even under high load. STIHL electric grass trimmers are user-friendly and easy to maintain. This gives the perfect opportunity to use the technique even for the beginner.

| Denial of responsibility | Contacts |RSS