How to rewind a trimmer line correctly on a STIHL grass trimmer

STIHL petrol grass trimmer How to fill a line in a trimmer. Changing the line for the trimmer in the trimmer (lawnmower)

First of all, winding the fishing line requires removing the spool (bobbin, bobbin) from the grass trimmer. the specific steps will depend on the complexity of the configuration and type of the product itself:

  • small electric grass trimmers with a working motor and spool in the bottom usually have side keys on both sides of the reel. When they are pressed simultaneously, the top part of the spool with the internal contents for winding the fishing line is detached, while the bottom part remains on the trimmer. It is advisable to disassemble the bobbin on a flat, smooth place so that the spring that is part of the construction does not pop out and get lost;
  • electric and gasoline grass trimmers with a curved boom without the possibility of installing a knife, as a rule, have a spool with a special wing nut: in such designs, one hand should hold the bobbin in a fixed position, and the other counterclockwise rotate the fixing bobbin on the rod nut-bar. After loosening the nut the entire bobbin is removed.
  • Electric and gasoline grass trimmers with a blade option on a straight shaft (e.g. STIHL grass trimmers) have a hole under the bobbin. To immobilize the rod, a screwdriver or other suitable object is inserted into this hole and a slow turning movement is used to achieve the relative positioning so that the screwdriver enters the hole and the bobbin is locked. The spool body is then turned clockwise (with the left-hand thread) and removed from the grass trimmer.

For the second and third cases, spools are disassembled in different ways, depending on the design. In reels with a drum, the drum is unscrewed; in reels with latches, the latch latches are pressed and one part of the reel is released from the other. If the bobbin halves are connected by thread, it is enough to turn them by hand in opposite directions until they are completely unscrewed.

Reel with two operating tendrils

In this type of bobbins, you should determine the number of grooves for winding the line lying on the inside of the spool:

HOW TO CHANGE THEMMER FILES THROUGH TRIMMER HOW TO RETURN FILES THROUGH THEMMER HOW TO RETURN FILES THROUGH TRIMMER HOW TO RUN?

For both cases, a 2-3 m trimmer line is taken. In single-cable spools the line for the trimmer is pulled through the through hole, its ends (tendrils) are put together and aligned, then reeled in the opposite direction to the bobbin rotation direction on the boom. inside the arrow usually indicates the correct reeling direction. If there are fixing grooves, the ends of the line are pulled through them or held by fingers of free hand, put through the through hole of the outer half of the bobbin, the bobbin is closed and fastened to the rod of the trimmer product.

The difference of line winding in two-channel reels is that initially a 2-5 m length of line is folded in half (to determine the middle fold), and the loop of the fold is inserted into a special groove between the grooves. Both tendrils of the line are wound each on its own groove, the fixation of tendrils and reel assembly is similar to the variant with one groove discussed above.

The first performance of this procedure may seem long and quite time-consuming, but with time and experience this task will be much faster and easier.

The video below will clearly show how to tuck the line for the trimmer into the grass trimmer reel and properly wind it. this operation is not anything complicated and with some patience is sure to succeed:

Reel with one operating tendril

The simplest option and uncomplicated sequence of actions:

trimmer, line, correctly, stihl
  • The size of the bobbin and the length of the original factory winding determine the recommended length of line for winding. 25 m.
  • One end of the line is inserted into the fixing technological hole located inside the bobbin.
  • the line for the trimmer is wound on the reel in the opposite direction to the rotation of the bobbin of the trimmer product. as a rule, on the inner side of the reel an arrow points in what direction the winding is done.
  • A small section of fishing line left free to display it outside. it is fixed in a specialized slot on the inside of the bobbin, designed to hold the winding when assembling the bobbin in working order.
  • The leftover end of the fishing line is passed through the hole on the outside of the spool.
  • Half of the bobbin is assembled and put on a rod trimmer device.
See also  Grass trimmer flexible shaft lubrication. Driven motors

READ How to Clean the Air Filter on an Echo Trimmer

How to wind a line for a trimmer on a grass trimmer spool: methods of winding and

Any garden plot owner knows how quickly weeds can invade an area. Effortlessly defeating them is easy with a weed trimmer. This indescribably useful tool is an indispensable assistant in trimming and cutting the grass. It’s no secret that an ordinary lawnmower can be used far from everywhere. In contrast, the trimmer can handle even very difficult terrain. This is especially true for those tools in which the role of the cutting element is not a knife, but line for the trimmer

A hand-held petrol mower. Changing the line in the bobbin.

In this video I show you how easy it is to wind the line for the trimmer on the spool of the hand-held mower without the help of others.

A reel with two working strands

In this type of bobbin, you should find the number of grooves for winding the line lying on the inside of the spool:

For both cases, a 2 to 3 m trimmer line is sufficient. In one-channel reels the line for the trimmer is pulled through the hole, its ends (tendrils) are put together and aligned, and then winded in the opposite direction of rotation of the reel on the boom. inside the arrow usually indicates the correct winding direction. If there are fixing grooves, the ends of the fishing line are pushed through or held by fingers of free hand, pushed through the hole in the outer half of the bobbin, the bobbin is locked and attached to the trimmer’s boom.

The difference in the winding of the line in the double-channel spools is that initially a piece of line 2-5 m long is folded in half (to determine the middle fold), and the loop of the fold is inserted in a special groove between the grooves. Both line tendrils are wound each on its own groove, fixing the tendrils and reel assembly is similar to the above variant with one groove.

The first performance of this procedure, maybe, and seems long and rather labor-intensive, but with time and experience, this task will be solved much more quickly and easily.

The video below will visually show how to tuck the line for the trimmer into the grass trimmer reel and correctly wind it up. this operation does not represent anything complicated and with some patience is sure to succeed:

trimmer, line, correctly, stihl

Preparation. remove and disassemble the bobbin

Most electric and gasoline-powered trimmers require that you remove the spool for line replacement. The FUBAG tool allows you to skip this step. For the instructions to be universal, we will still consider it in detail:

Clamp the shaft. Insert the stopper into the corresponding hole. This can be a thin screwdriver or a metal bar.

Unscrew the bobbin case. In our example strictly clockwise.

Unscrew the cover according to the direction indicated on the housing.

The preparatory phase is complete. You can proceed to winding the line.

trimmer, line, correctly, stihl

How to wind the line onto the weed trimmer reel

Algorithm of winding

Lay the line for the trimmer according to the direction indicated on the element body.

See also  How to tuck a line into a STIHL grass trimmer STIHL FS 38

Insert the short end into the groove on the side of the reel.

Fasten the long end in the opposite groove.

Place the spool with the line wound in the bobbin case.

Cut the line ends leaving 10 to 15 centimeters.

The line change is complete and all that’s left to do is screw the bobbin onto the grass trimmer and you’re ready to go.

Winding a fishing line on a grass trimmer

The measured and careful removal of the bobbin from the grasshopper reel makes it possible to go directly to the winding of the line. Design features of the head, the number and location of fixing holes dictate the sequence of actions when performing this operation, as well as determine the methods used. Today there are several varieties of spools, depending on the number of fishing line tendrils and methods of winding it:

Grass trimmer reel with one tendril

Many owners and professionals say it’s easy to operate and reel in a single mast. Depending on the manufacturer, the length of the line to be threaded varies from 2 to 5 meters. In the head, the end of the fishing line is inserted into a special technological groove or hole, and the winding is done in the opposite direction to the working rotation of the bobbin. Most spools have arrow marks on the outside of the housing to show the direction of travel of the grass trimmer reel.

After winding it is necessary to leave the free end 15-30 cm to strengthen the centrifugal force, which is decisive for the extraction of trimmer line in automatic and semi-automatic spools. Thread the left end through the working hole of the spool and assemble the head.

Trimmer head with two tendrils

After removing the bobbin from the spool body, determine the number of thread winding spools (1 or 2). There is no fundamental difference between coils with one and two grooves, but there are problems with operation in case of careless spooling into a paired groove. Because neighboring lines are likely to become entangled in the tool, it may be impossible to retrieve new lines after the work strands have worn out.

Regardless of the number of spools, trimmer line length of 1 is taken for refueling.5 to 3 meters. Reeling must be done in reverse rotation of the head, because winding with the motion of the head will lead to the fact that the line for the trimmer will not be extracted from the bobbin. Once the line for the trimmer is tucked into the grass trimmer reel, the free ends (15-30 cm) are threaded into special holes. Then you assemble the head in the reverse order of disassembly and check its functionality. Do not worry if the ends of the two tendrils are very different in size, because when you start the trimmer for grass, the blade mounted on the protection will cut off the excess.

Grass trimmer head with automatic line threading

Some models on the market have a spool with an automatic winding mechanism. The owner only needs to correctly tuck and fix the ends in the head, and the winding operation will be performed by the tool itself when turning on the working mode. Incorrectly wind the line for trimmer in the grass trimmer with this head is almost impossible, as the spool independently determines the position of the tendrils. The advantages of the automatic head trimmer for grass can be attributed to the ease of filling the line, and the disadvantages. frequent damage to the mechanism due to the complexity of design and high cost.

Block: 3/3 | Number of characters: 3075

What is the best line for a grass trimmer??

There are several parameters to consider when choosing a line.

The list of the main characteristics of the cutting cord includes:

  • The thickness of the line. the most common threads on the market are between 1.2 and 4 mm thick. Thin filament, no thicker than 1.6mm, for trimmers with less than 0.8L. с. Most often this cord is used in cases where the farm has a low-powered electric trimmer with a line and a knife. Cords up to 2mm up to 2.6mm are for trimmers with 1 to 1.8L horsepower. с. These lines can successfully remove not only freshly grown, but also quite old dried out vegetation. Thicker lines, from 3 mm in diameter, are designed to work in combination with gasoline-powered mowers, with a minimum power of 3 liters. с. A cord with this thickness performs well when mowing large or dense wild vegetation;
  • the shape of the grass trimmer cord. a lot depends on this factor, because when mowing the grass, the cord does not cut the stems, but hits them repeatedly. It is the shape of the thread that influences the speed of cutting the grass and the neatness of the cutting line. The most common threads on the market are round. This cord is suitable for any kind of foliage. Square filament is a little less common on the market. It is best at removing large, hard stems, and is often used for mowing wild shrubs. Star trimmer lines are also on the market. It stands out for its low traumatism for the grass, so it is best used for the care of decorative natural lawns;
  • material. in most cases, manufacturers use nylon, polypropylene and polyamide for cutting cords. Cheaper trimmer cords are made from nylon with polyethylene additives, which significantly reduces the resistance of the thread to wear and temperature.
See also  STIHL fs 130 weed trimmer fuel consumption

Also, when choosing a cord, you need to take into account the type of equipment that will be used to work on the site. If the farm uses electric grass trimmers with a fishing line and knife, it is best to equip them with thin round cord, which create a minimum load on the electric motor. If a powerful lawn mower is used for the care of the site, then you can confidently use a cord with any thickness and cross section, including homemade lines from a plastic bottle. The load on the gasoline engine in these cases will be almost imperceptible.

Tips and recommendations on how to wind the line for the trimmer and what you need to know

There are some useful tips and recommendations that will be useful to learn not only for beginners, but also for the experienced craftsmen. These tips will help prevent negative consequences in the form of injuries and malfunctioning of the mechanism. These recommendations state the following:

  • Do not make the cover until it clicks into place. And it is 2 or more clicks, depending on the number of latches. If one ratchet does not click into place, when you start the tool, the reel can jump out and injure a person
  • Do not wind the line for the trimmer with a strong retraction, as well as in an amount greater than you can put it in place. It is better not to reel in more tooling than not to reel it in, as this will lead to negative consequences in the form of inability to unwind it when necessary
  • If you own the tool not with two leads of fishing line, but with one (usually these are low-powered units), then the winding process is performed in a similar sequence as described above, only with the difference in the absence of the middle edge between the extreme bases of the spool
  • After replacing the material, you must first check the functionality of the tool, and then proceed to mow the grass. If not checked beforehand, the fishing line can unravel and injure people

This is interesting!Choose proper quality material so you do not injure yourself when working with chain saws, trimmers and brushcutters. In the process of mowing grass small stones and other materials fall under the rotating parts, which can fly long distances, so, despite the fact that the line for trimmer is not a knife, work with the tool should be carried out in special protective gear. The result of the work done is the following. after the replacement of the new material, the usual one is enough for an area of up to 600 square meters, but taking into account the presence of a reinforcing layer on the fishing line. Conventional nylon materials lasts less, which is important to consider when working. Don’t try to mow thick-stemmed grass with a fishing line, as special metal discs or knives are available for this purpose.

| Denial of responsibility | Contacts |RSS