How to season the head of a trimmer for Huter grass. How to replace a fishing line for a trimmer on a trimmer?

How to install a fishing line for a trimmer on a trimmer coil for Huter grass

In order to wind a fishing line for a trimmer, it will need about 10-15 minutes. What is the coil of a trimmer for grass? A plastic case with a snot cassette on which there is a special hook for a comfortable winding of fishing line.

In fact, all the coils of trimmers have a similar principle of fastening, this is a central screw-button, when pressed, it becomes possible to stretch the fishing line for the trimmer of the required length. The photo below shows several examples of different coils for trimmers.

Bobbins of the trimmers, the motor of which is located near the ground, have a different fastening to the rotation axis, they have two buttons on the coil located at the edges that need to be squeezed, the rest of the thread is no different from the other cassettes.

The principle of proper winding of the fishing line is identical in all of the above cases, therefore, for example, we will see the standard option with 2 antennae.

To remove the coil with a fishing line, you need to unscrew the screw in the center, but keep in mind, the thread there will have to be twisted clockwise, it is specially made so that during operation it does not open under the influence of centrifugal force.

Further, using the screwdriver, to disassemble the head and pull out the coil, on which the fishing line for the trimmer is specifically wound.

Having measured the desired length and folding twice, it is necessary to season the fishing line for the trimmer to the coil, leading, ultimately, its ends opposite each other (for this there are special slots for fixation).

After that, you need to collect the head in the back, passing the ends of the cord in two corresponding holes.

If there are doubts or it is not completely clear how to charge a fishing line for a trimmer for a trimmer for grass we advise you to look: how to correctly wind the fishing line for a trimmer into a lawn mower.

In this video, the instructor will thoroughly open the trimmer head in steps, measure the right amount of fishing line, usually from 2 to 4 meters, and demonstrate the assembly and installation for a trimmer for the grass.

Huter grass gasoline trimmers: types and subtleties of operation

Cleaning a personal plot or house area is a very fundamental component that assigns a certain place, whether it is a cottage or territory of a high.rise building, a pleasant appearance and spectrum. It has already long been traditional devices for the type of ordinary braids for grass are not composed of effective. They were replaced by such a thing as a lawn mower or as it is still called a lawn mower. Such a gasoline trimmer for grass is an effective device that allows you to perform the mowing of grass rapidly and simply. If you read about the best solutions for weed, then the model that producer Huter produces are listed in the middle of consumers with more high.quality.

If the coil allows you to wind fifteen meters of thread, then you should not wind so much, there is enough ten, that is, if you fold in two layers, you get five meters each. With another capacity of the fishing line, it is worth using the same rule.

In the case when an ordinary round thread is used, it is better that it is 3.3 mm with a diploma. If this is a figured fishing line for a trimmer, then its thickness should be less, for example, 3 mm.

It is better to wrap both segments of the fishing line at once on the spool, and you need to start with its bending

It is important to prevent overlap in the direction of the arrow. It is also important to be able to perfectly pull the thread

There will be a thread to be pulled, it may go over. If not unit, can twist. In order not to cut your hands on the figure thread yourself, you should wind it in gloves.

No need to leave the ends of the fishing line long. This can lead to its tightening.

HUTER GET-600 Operating Instruction Institution Online. Page 9

The Huter Get-600 instruction for the device trimmer for grass contains pages in Russian.

File size: 649.14 KB. Consists of 16 pages.

Замена лески. Huter GET-600. Катушка с белым кольцом.

You can download PDF file of this instruction: download pdf

Assembly. 7.one. Free a trimmer for grass from factory packaging. 7.2. Screw the protective casing with the attached screws. 7.3. Wrap the fishing line for the trimmer of the desired diameter to the coil as shown in Figure 3, and then fix the coil on the trimmer. 7.four. Adjust the length of the trimmer for grass to your height.

Instructions with a step.by.step description how to wind the coil of a trimmer for grass and lawn mower

In order not to make a mistake with the choice of a suitable fishing line for your tool, you should first disassemble the head and look at the side wall of the coil. This information is usually presented on a tip, which will not allow us to make a mistake using the appropriate equipment.

How to open a self.supporting coil (spool) motorcycles.

If the information on the coil about what diameter the fishing line for the trimmer can be refueled, then this information can be clarified in the instructions. Having decided on the thickness or diameter of the equipment, it remains to figure out how to charge it. There are two ways for this, but not for all they are applicable. Consider both methods in details, and already depending on what models and trimmers you use, you are determined on your own which option is suitable.

It is interesting! The principle of how to wind a fishing line for a trimmer for a tip of motorcycles is appropriate not only for autonomous benzar groups, but also for electric trimmers.

Peculiarities

If you read the features of the models of this manufacturer, then to begin with, it should be said that this company from Germany was based on one thousand nine hundred 70 nine years. All the equipment that is produced under this brand is created by qualified engineers and developers and is being verified at every step of creation. In general, the lawn mowers of this German company are massive and fairly productive models. Their use allows you to cut grass in almost all criteria. Very often the best models of this company are used specifically for professional purposes. One of the fundamental features characteristic of all models of the manufacturer will be that motor.coats from Huter are equipped with a two.stroke engine with air cooling and electric ignition. This function makes it possible to ensure the highest power of the device and high.quality execution of the intended target.

The quality of the spark is determined by its ability to set fire to a correctly formed air-fuel mixture in working criteria. A weak spark in the criteria for lean pressure and temperature in the combustion chamber cannot do this. Ignition occurs later or does not occur at all. A bulge appears in the operation of the motor, the motor does not gain momentum, vibration, detonation appears, the “blast shock” effect may seem in the starter.

The insidiousness of this breakdown lies in the fact that the diagnosis below the above methods does not give 100 percent conviction of the performance of the ignition reel. Such implicit breakdown, when there seems to be a spark, but it is not completely true, often misleads and forces the difficulties with the ignition coil to a carburetor malfunction. Ordinary acts in such cases are an increase in the supply of fuel. It turns out that such a spark can set fire to the enriched mixture, but there is no correct. But the introduction of an enriched consistency leads to the rejection of the cylinder-piston group and muffler. Therefore, in such controversial situations, check both the carburetor and the ignition coil again.

Advantages and disadvantages

It should be slightly said about the strengths of the gasoline trimmers of the aforementioned manufacturer. The main ones can be called the subsequent:

  • The presence of a two.stroke engine with a power of more than three horsepower, having air cooling and electrical firing;
  • A tank made of translucent plastic, which allows you to know exactly how many fuel was spent during operation;
  • The opportunity for a person to work is comfortable-this is obtained due to the presence of an ergonomic handle according to the type of bicycle and a special mechanism of extinguishing various kinds of vibrations;
  • Here, a high.quality cutting headset is used in the form of a cutting knife and fishing line of the highest strength;
  • A wide capture of 25.5 cm is also used here, which makes it possible to perfectly and rapidly mow grass, shoots and other greens;
  • A protective casing that protects a person from the hit of mowed grass, pebbles and various garbage;
  • Shoulder belt, which allows the operator to work for a long time and not feel lethargy;
  • Simplicity of maintenance and work. the mechanism of work and the device of models from Huter is very ordinary, which will allow simply to understand their implementation even a little.known person;
  • Reliability-such a gasoline trimmer for the grass can work for a long period of time without stopping, with all this it does not heat up due to the features of the air cooling system;
  • The possibility of unhindered movement around the site. taking into account that gasoline trimmers for grass, unlike electronic ones, are completely independent of the presence of a socket, which guarantees a person freedom of movement.

At the same time, there are a number of shortcomings that cannot be mentioned, but specifically: specifically:

  • Noise during work. gasoline trimmers for grass not only from Huter, and in general, they vibrate very much and publish a strong noise, which makes uncomfortable working conditions;
  • Contamination of nature. models working on combustible, during operation form various kinds of exhaust gases, which harm the environment;
  • The highest price-trimmers for grass of the described type have the highest price due to the fact that they own the highest performance and good technical features.

Recommendations related to repair

Mechanical problems are associated with damage to the trimmer head. This component is most often exposed to wear, and this element often contacts the environment. There are several options for a breakdown that is mechanical.

Electric version of braids for grass

Self.propelled type of these units can be used anywhere, but only next to the power supply. Silent, they are often used near schools, kindergartens, as well as hospitals and clinics. They are quite actively used in private territory.

The models are easy to manage, have a low noise level, high reliability, as well as an acceptable price.

Winding fishing line on a trimmer for grass

Measured and accurate dismantling of a spray from the coil of braids for grass makes it possible to go directly to the winding of the fishing line. Design features of the head, the number and location of the fixing holes dictate the sequence of actions when performing this operation, and also determine the methods used. Today, there are several varieties of coils depending on the number of antennae antennae and refueling methods:

Trimmer coil for grass with one osmus

Many owners and experts note the simplicity of the operation and refueling of bobin with one mustache. Depending on the manufacturer, the length of the refueling fishing line can range from 2 to 5 meters. The end of the fishing line is inserted into the head in a special technological groove or hole, and the winding is carried out in the reverse work rotation of the bobbin side. On most coils on the outer side of the case there are marks in the form of arrows, which indicate the direction of the movement of the bobbin of the trimmer for the grass.

After winding, you need to leave the free end of 15-30 cm to strengthen the centrifugal force, which is determining when extracting a trimmer fishing line in automatic and semi-automatic reels. The left end is extended through the coil work hole and make the head assembly.

Trimmer head with two antennae

After extracting the spray from the coil body, we determine the number of streams for winding fishing line (1 or 2). There is no fundamental difference between bobbins with one and two grooves, but with a careless refueling in a paired groove, there are problems with operation. Due to the likelihood of weaving neighboring tools, a situation may arise when after the wear of the working antennae it is impossible to extract new.

Regardless of the number of streams for refueling, a fishing line is taken for a trimmer from 1 length.5 to 3 meters. The winding must be carried out in reverse rotation of the head to the side, since the winding in the direction of movement will lead to the fact that the fishing line for the trimmer will not be removed from the bobbin. After the fishing line for the trimmer is tucked into the coil of the trimmer for the grass, free ends (15-30 cm) we stretch into special holes. Next, collect the head in the reverse disassembly order and check the performance. Do not worry if the ends of the two antennae are very different in size, since when the trimmer for the grass is launched, the knife installed on protection will cut off the excess.

Trimmer head for grass with automatic line dressing

In some models presented on the market, a coil with an automatic winding mechanism is installed. It is enough to correct the owner and fix the ends in the head, and the winding operation will perform the tool itself when included in the operating mode. It is almost impossible to incorporate a fishing line for a trimmer to a trimmer for grass with such a head, since the coil independently determines the position of the antennae. The advantages of the automatic head of the trimmer for grass include the simplicity of the line for refueling, and the disadvantages are frequent breakdowns of the mechanism due to the complexity of the design and the high cost.

How typical mechanical defects and ways to eliminate them with your own hands are manifested

The following damage to the kinematic scheme most often occurs on the electrimmer:

  • the bearings of the electric motor are cleaned or spoiled;
  • The fishing line for the trimmer is tangled or broken due to incorrect winding to the coil;
  • The torque from the engine to the mowing head is not transmitted;
  • The plastic case and individual parts melts when overheating due to increased loads;
  • enhanced vibration of a rotating head is created, which makes the kosbu.

How easy to check the work of bearings

It is enough to update the external clip regarding the shaft and immediately with tactile sensations of the fingers to evaluate the smoothness of their work, the state of backlash. Broken and worn bearings must be replaced. Do not forget to update the grease if necessary: ​​remove the stream and apply a new.

Trimmer heads are created by three types of structures, implying the issuance of fishing line in one of the ways:

The overwhelming number of products uses semi.automatic fishing line. It also allows a manual regime for adjusting the length of the cutting area. A large number of breakdowns are associated with a violation of operation rules recommended by the manufacturer, when a trimmer for grass begins to work outside of its capabilities. These include:

  • a significant excess of the diameter of the cutting fishing line leading to an increased load on the engine, intermediate shafts, gearbox and mechanical parts of the head;
  • installation of homemade knives or chains instead of standard structures;
  • Incorrect winding of the fishing line.
season, head, trimmer, huter, grass

Such are the homemade like “eternal fishing line for a trimmer for grass” not only damage the kinematics of the lawn mower, but also injure people, causing harm to their health. I do not advise doing this to do. There is no economy here.

How easy it is to wind a fishing line for a trimmer on a spool

Usually this issue is difficult for beginners. Especially for this case, I made a narrative on my channel Yandex Zen. I invite you to familiarize yourself: information is presented by pictures with an explanatory text.

The engine works, but the spitter head does not rotate: what’s the reason

The breakdown is associated with the cessation of the transmission of the torque of the engine to the working body. A defect can occur anywhere in the gear. Most often, in models with the gearbox, the reason lies in the wear of the working faces of the gear. over, if the teeth on one are worn out, then both must be changed at once, because the second also suffered

Hysteria gear malfunctions most often arise after the loss of grease in them, which, by the way, each manufacturer is noteworthy. The fact is that the design of the trimmer gearbox body is not completely tight

Otherwise, its cost will increase strongly. Gears should always work in lubrication, and it is consumed. If it is not replenished, then the breakdowns are inevitable, which happens quite often. In cheaper structures without a gearbox, a coil of the coil is fixed through a plastic sleeve to the shaft. During constant loads, plastic heats, and the sleeve wears out during operation, the head begins to hang out. When the critical value of the backlash is reached, the sleeve must be replaced.

Why can the lower part of the composite rod

The reason for increasing temperature in this place can only be strong friction of rotating parts about fixed parts. In other words. the spring shaft is tightly pressed against the walls of the plastic insert. (See above the photo of the details of the composite bar). This leads to melting the plastic up to damage to the sleeve and the formation of a continuous lump from it, penetrating the boots of the shaft. When cooling in the air, a monolithic structure is created, which can block rotation and even jam the engine. The rotating spring shaft of the bar should always work in the environment. It must be regularly lubricated. Timely perform preventive examinations and work.

Why is there increased vibration and how to get rid of it

We understand that any well.balanced part regarding the axis of rotation does not create vibration. Beats arise where the factory balance is broken or there is a marriage. The mowing head has a fairly large mass. Therefore, it is often the cause of increased vibrations, but in each case it is necessary to study this issue on a specific design. The owner of a short Masterlom video, Masterlom, shares his experience in eliminating such a defect on the Tekhmann DCE-2014B electrician. His achievements and ideas can be useful to you in eliminating vibrations. I recommend to see.

Как заменить леску на тримере, мото косе электро косе.

The main malfunctions of the coil

Users of the electrimmer and lawn mower often face a problem associated with a semi.automatic braid head. Coil malfunctions can be as follows:

The cord spontaneously lengthens

There are situations when a user of a trimmer for grass notices a very fast fishing line consumption. At the same time, he never hit the ground with a button to lengthen the fishing line. The reason that the fishing line for a trimmer spontaneously lengthens, cutting off a special knife on the casing of the device, may be the absence of a spring in a mowing head. Often beginner users of mowers, trying to charge a fishing line for a trimmer into a coil, forget to install a clamping spring in the head, or completely lose it when opening the lid, and in the future, they do not even suspect its existence.

Also, a fishing line for a trimmer can lengthen without using a button if the spring is weakened. If the spring check confirmed this fact, then it is necessary to put several goals under it to strengthen its clamping properties.

season, head, trimmer, huter, grass

Popular models of electrocos

One of the popular options is the STIHL FSE-81 Elekhil. This is one of the most powerful trimmers for the lawn. This device includes the Autocut C5-2 coser, designed to work in small areas. It is convenient to mow it next to the flower beds, borders. She clears the territory near shrubs and trees well, and also carefully processes paths.

How to wind a fishing line for a trimmer for a trimmer for grass. How to remove a coil from a trimmer for grass.#Victorpolev

This braid for grass has a number of advantages that are that it regulates the revolutions using electronics. The design allows you to save the trees from damage. The circular handle allows you to perform efficient work, maneuver, and also mow in hard.to.reach places. It is easy to transport.

There are other options that have established themselves in work in horticultural plots.

How to remove the coil and replace the fishing line for the trimmer

The owners of the trimmers, mainly beginners, confuse, bordering on panic, when it becomes necessary to change the cutting tool or fishing line for a trimmer in a reel. Very often, when trying to unscrew the mowing head, users simply make it unusable, not suspecting that it is unscrewed in the opposite direction. So that this does not happen, if you need to replace the tool, it is recommended to familiarize yourself with the step.by.step instructions given below.

  • Before refueling the fishing line for the trimmer to the coil, drown out the engine of motorcycles or de.energize the ethletric trimmer for the grass to avoid injuries that may occur in case of accidental rotation of the cutting tool.
  • Unscrew the nozzle mounted on the gearbox shaft. To do this, the shaft must be fixed by combining holes on the puck and on the axis, and inserting a metal rod or screwdriver into them.
  • Unscrew the nozzle. You should know that the thread on the shaft is left. Therefore, to twist the coil of the trimmer for the grass should be right, that is, clockwise.
  • Disassemble the mowing head. Most often, the head cover is attached to the fixers. To remove it, you need to drown these latches into the case, pressing the edges of the lid. If your trimmer has a semi.automatic mowing head, which has a button from below, then disassembling the nozzle should be done carefully, since you can lose a spring that sometimes flies away when removing the cover.
  • Cut the required amount of fishing line. Usually its length is 5 meters. Use the cord of the diameter that is indicated in the instructions for the tool. It is not recommended to exceed the maximum diameter of the fishing line, since this will lead to increased load on the engine and greater consumption of gasoline.
  • Find the middle of the segment of the cord, folding it in half. You will get a loop.
  • Special grooves are cut out inside the coil (there may be holes). Insert the loop from the fishing line into this groove.
  • Wind a fishing line for a trimmer to a coil, turning it counterclockwise. You need to refuel the cord as evenly as possible, the turns should be laid without ceiling and with good tension. When the winding is finished, leave the free ends of the fishing line about 20 cm long and fix them in the grooves located on the sides of the coil.
  • Collect the braid head. Before you finally collect the nozzle, do not forget to insert a spring and washer (if it is available). Install the coil in the case, and prone the ends of the cord through the holes or eye.
  • Dress the lid and fix it with latches.
  • Screw the nozzle back to the gear shaft, also fixing it with a screwdriver. Tighten the coil of the trimmer for the grass will need to go to the left (against h. Arrows).

We offer to familiarize yourself with the tomato match characteristic and description of the variety

Preliminary preparation

First of all, to wind the fishing line, it is required to remove the coil (bobbin, spool) from the trimmer for the grass. specific actions will depend on the complexity of the configuration and the type of product itself:

  • Small electric trimmers for grass with a working location of the engine and coils in the lower part, as a rule, have side keys on both sides of the bobbin. With the simultaneous press on them, the upper part of the coil, along with the internal contents for winding the fishing line, is disconnected, while the lower remains on the trimmer. It is advisable to analyze the bobbing in an even smooth place, so that the spring does not jump out and not be lost;
  • Electric and gasoline trimmers for grass with a curved rod without the ability to install a knife, as a rule, have coils with a special lamb: in such structures, you should hold the spool in a fixed position with one hand, and rotate the fixing bobbin on the bar with a barack’s baracks. After disconnecting the nut, the whole bobin is removed.
  • Electric and gasoline trimmers for grass with the ability to install a knife on a straight rod (for example, trimmers for STIHL grass) have a hole. For the immobility of the bar, a screwdriver or another suitable object is inserted into this hole and, with slow rotation, such a mutual arrangement is achieved when the screwdriver enters the hole and the bob is fixed. After that, the coil body is scrolled clockwise (with the left thread) and removed from the trimmer for the grass.

For the second and third cases, the coil, depending on the design, are versed in various ways. In the bobbins with a lamb, lamb is twisted, in the reels with latches, latches-fixers are pressed and one part of the coil is freed from the other. If the halves of the spool are connected by thread, then it is enough to turn them with your hands in the opposite directions until they are completely developed.

Repair of the head of a trimmer for grass Huter Get-600. Modernization of the Huter Get-600.

There is nothing to write about the car. Rides. Pleasing. I’m not going to copy the corresponding forum. I decided to share personal experience in another.

I have in the farm in addition to a classic braid for grass and a pair of gasoline electric trimmer for Huter Get-600 grass

Under certain circumstances, it turned out that the head in the kit is very tender, and with a slight effort about the bricks hidden in the grass broke. I did not dare to buy this head anywhere on the Internet, including on Alibab without trying on a mower. Local shops shook their hands

I had to select from the availability.To begin with disassembly. To remove the head, you need to either disassemble the entire trimer, and holding an anchor in a vice to twist it, or follow my inhumane approach and carefully cut the body with a hacksaw on metal and sleep the shaft, creating a groove for a screwdriver for a screwdriver. Further, everything is simple. Thread m8 ordinary right. The head of the head is still thrown out. Island, wound around solves the problem of 10 minutes. Then it unwinds it and ripens about the same ill.fated brick.

Then a trip to Magaz behind a new head. Many heads have been tried, I stopped at one. The price of the question yourself in the photo see.

The revision is as follows: 1. Sprinkle the long protruding hub up to 5-7 mm.

By that time, the file had broken down, the wheels for the corner grinder ended, so I hid on the sandpaper. You need to cut off so that the impeller does not hurt the mowing housing, and there was no very large gap, otherwise the juice of grass and pieces of snails will be anchored inside.2. Drill a hole with a drill 8 mm upper part. The fact is that entering the hole is 8 mm, and for thread on this head is left under M6. The shaft of our trimmer for grass 8 mm. If you drill more than 8 drill, it will be freely scroll.3. Nothing that the m8 nut does not climb inside. Put the puck of an ordinary flat 8 mm flat with an outer diameter of 14 mm and tighten the nut.

The nut works for the anti.income, so it should be delayed when rotating the head. With a great desire, you can grind a threaded sleeve with an external diameter of 13 mm with a thread M8 and stick on an epoxy inside. Then the head needs to be drilled by 8.2 mm and just go to the shaft. This is the next stage when.All. Tests have shown that now I have an automatic head, working standardly from a blow to the ground, in contrast to the original, which you need to do it manually. Does not scroll at the shaft. All temporary. constantly.

Комментарии и мнения владельцев 33

Log in or register to write Комментарии и мнения владельцев, ask questions and participate in the discussion.

Without refinements, I picked up such a coil, all one to one, I threw the nut from the old coil, the price tag does not please, I cost 720r.A coil for a trimmer for grass, automatic, nut M8 x 1.25 right, fishing line for trimmer 1.6 mm Denzelarticule: 96308

season, head, trimmer, huter, grass

I bought such a head and drilled a hole of the desired diameter in it. But in the process of drilling, the drill took a little to the side. Now alignment is violated and vibration is felt during operation. So I think to buy one more. Maybe there is a cunning/secret, how to drill evenly?

PATIRON DL-1223-a complete analogue of the coil in the article for 250 r. In the most common online tool store. You don’t even need to undermine and drill anything, only the washer will be needed.

You put the Patiron DL-1223 on the Huter Get-600? Everything came without improvements?

Hello! I did everything exactly like in this post! Parents are satisfied!

If there are 3D printers, then it is not a problem to make, but 500 are curled up, it’s easier to buy a new one. If you need a 3D model of the cover by which they cast, then this is. write.

I really want the cap model, please throw off!

If there are 3D printers, then it is not a problem to make, but 500 are curled up, it’s easier to buy a new one. If you need a 3D model of the cover by which they cast, then this is. write.

Hello! Please share the cover of the cover!

Repair of the head of the head of a trimmer head for Huter Get 600 grass also needed after meeting with a pebble But why cut the head with a hacksaw. because it is easily removed from the anchor shaft: for this we unscrew the side screws above the electric motor and insert a wide screwdriver into the collapse of the case and turn it to remove it to remove it to remove it upper yellow hatchet. Under it we will see the rotor shaft with the “bald ones” for which you need to hold with a key or pliers and unscrew the head behind the trimmer head body. There is a m8 nut with ordinary right thread. For one you can get the collector brushes and see the collector node of the motor. if something is cleaned with zero with sandpaper and generally clean the body of the motor from dust. As for the broken latch on the lid, then it all depends on the degree of breakdown: if the tip of the latch fell off, then we do not break off the opposite latch, and if the latch broke off to the lid, then we break off (bite off) opposite the other latch to the lid. This is necessary for balancing- so that the renovated head does not vibrate. Next, we act as follows: from the end of the rotor (after removing the head and removal of the rubber plug above the nut) there is an already seconded recess. we drill 3 drill.5 mm to a depth of 10 mm hole and then cut the thread m 4. Now we are drilling in the head of the head of the trimmer for grass (without latches) in the center of the hole of the diamond of 4 mm. All: now we collect everything back, and fasten the lid of the head with a screw under the screwdriver with the corresponding puck. The thread is put on the screw, and the trimmer for the grass turns to the left. the lid will never unscrew. I have experienced and the second season the head on the trimmer is working. If you do not want to drill the rotor shaft, you can make a transition sleeve with a diameter of 14mm-inside on the one hand, the M8 thread (preferably 1st size in the sizes in the sized) and on the other side of the sleeve M5 or M4 carvings-where you will fasten the cover again with the help of the screw. Trimer head is considered a diameter of 75 mm, but in reality, if it is cleaned with sandpaper outside, then it will be 74mm, so support a tin can from condensed milk. cut with ordinary scissors the desired size of the window for a trimmer fishing line and put this “case” on the head and in the head screw the end with a screw through the lid to the anchor and you will be a durable head. As for the replacement with another head, then it must be borne in mind that the head with “ribs” is needed to cool the electric motor and anyone will not work. Now they began to produce on the Get600 heads with curved cooling ribs, then it should be taken into account that they should suck the air inside the engine when it rotates.

Such a muck instead of thread was in my case A diameter is 8mm, I think to cut and order an adapter from the turner for a universal head And so the trimmer for the grass is good, powerful and not expensive, unfortunately the spool sucks.

| Denial of responsibility | Contacts |RSS