How to start a trimmer for grass gasoline Redverg. Gasoline trimmer for grass: assigning the tool in the country

Repair of an electric trimmer for grass

The electric trimmer for the grass replaced the usual spit. Today, most urban residents do not even know how to use a “rare” tool correctly. A modern person does not need this, because he has an electric counterpart. But if an ordinary braid had to just sharpen from time to time, then things are more complicated with the power tool. Equipment requires a certain care, and if a malfunction occurs, the repair can lead to big expenses. However, it does not always make sense to carry the failed tool in the workshop: often you can cope with the breakdown on your own.

To understand what exactly can break in an electric cost, first you should figure out how it is arranged.

Ethletric trimmer for grass usually consists of the following elements:

The current is supplied to the power unit through the connector on the case, to which the cable is connected. Inside the rod is hollow. It plays the role of a protective shell for a flexible shaft, transmitting torque from the motor to the coil of the trimmer for the grass. The handle located on the case has a button, when pressed on which the device turns on.

INGCO Grass Trimmer and Bush Cutter Unboxing

The described design is considered a classic. However, there are options for executing the tool in which the motor is located in the lower part near the coil, as well as the battery versions.

How to get a lawn mower: Action Procedure

To start a gasoline trimmer for grass, you must do the following:

  • Close the air conditioning by shifting the lever.
  • Turn on the ignition. For this you need to turn the key or handle to the appropriate position.
  • If there is a manual fuel pump on a gasoline, then you need to press it 2-4 times until a combustible mixture appears inside the primer.
  • Put the device on the ground. Click with a knee on the part where the engine is located, and slowly pull the starter handle until the moment when the resistance appears (the so.Called hook). It is necessary to ensure that the gas mowing disk is currently not in contact with anything.
  • Then, with a sharp movement, it is necessary to stretch the cord on yourself 3-5 times.

Когда триммер для травы заведён, заслонка открывается и фиксируется в среднем положении. Before operation, you should wait about five minutes. Let the lawn mower will work at idle.

If you cannot start, you need to open the damper again. Otherwise, the candle will flood the fuel during subsequent movements of the cord. After that, you should 2-3 times start an open handbrake engine. If you can’t start it, you need to close the damper and try several more times.

The warmed motor is started elementary: its switch is put in the working position. Well, then the cord pulls to the start.

The common mistakes, which are often made by inexperienced owners, include the launch with unknown ignition or making jerks for starting more than five times when the damper is closed.

Useful information for those who do not have a trimmer for grass after winter

Why does a trimmer not start for the grass after wintering ? What are the main reasons for this problem?

Benzotrimmer may not start due to the fact that the fuel remained in the tank last year, which, simply put, was exhausted. Two signs may indicate this: the candle is dry and there is a spark. To eliminate this problem, you just need to replace the fuel.

In addition, a gasoline trimmer for grass after winter starts a little differently. Open the damper and pump up a little gasoline into the carburetor, and then take the handle until you feel some resistance. After that, you can launch.

With a long simple, an air filter can clog. Evidence of it may be the launch of “hot”, after which the trimmer for the grass immediately stalls. Perhaps in the cold season the filter managed to clog with dust. Two options are possible here: first you need to clean it, and if this does not help, then you need to purchase a new filter.

In general, a similar conversation should begin with the fact that after the purchase of a garden benchmain tool it would be better to get to know the instructions attached to it initially. Then many problems could have been avoided. But since this happened a gasoline trimmer for the grass does not start, you need to look for sources of inoperability. And in this article we will consider the main reasons why the trimmer for the grass is not started by the example of the Elitech T750 model, as well as tell the general recommendations for such a tool.

See also  What gasoline to refuel a gasoline trimmer for grass. What oil to choose for refueling in a trimmer for grass or types of lubricants

Start with banal! We will figure out how to properly start a gasoline trimmer for grass. Maybe such that the reason lies here.

First you need to bring a red toggle switch on a trimmer bar for grass to position “i”. This means the inclusion of power supply. Then you need to switch the fuel supply lever on the carburetor and use the fuel “suction” button (looks like a pipette, is on a carburetor). This is necessary to supply gasoline to the engine. Fuel supply lever to return to its original position. At the end, sharply pull the starter handle on yourself. The trimmer for the grass should earn. Try it several times if the first time does not work. If after such manipulations the situation has not changed and a gasoline trimmer for grass does not start, then it is worth it to inspect it on your own first before you lead to the service center. There are two main reasons why the garden trimmer is not started:

The second reason why the garden tool does not work is the fuel ended. On Elinech T750, a fuel tank is located near the motor, but on most trimmers it is there. We unscrew the cap from the tank and pour gasoline there (the most optimal version of the AI-92, it is inexpensive and does not clog the carburetor as AI-76). Do not forget to add special oil for engines to the tank, 50 grams on the gas tank is enough, without it the motor will begin to “sneeze” and quickly become unusable. After cover the tank with a cap, wipe the surface of a trimmer for grass with a dry rag and our hands. We also make the above manipulations to include a garden tool.

start, trimmer, grass, gasoline, redverg, tool

If the gasoline trimmer for the grass does not start as before, then it makes sense to give it to repair. And the reason for such a solution is simple. If you do not have appropriate skills, the repair of equipment is practically impossible.

In order for the tool to serve as long as possible and do not arise such malfunctions, you should first get acquainted with the instructions for the operation of a trimmer for grass

start, trimmer, grass, gasoline, redverg, tool

Also, pay special attention to the engine time for the grass for the grass. Make a short break every 15 minutes of work and, finally, take care of the tool correctly, wipe it after work, lubricate with graphite lubricant. Observing such simple rules, you can significantly increase the life of the tool and it is quite possible that you will not have to look for the reasons why the gasoline trimmer is not started for grass. Why is a trimmer not starting for grass gasoline? Prerequisites and their elimination

Why is a trimmer not starting for grass gasoline? Prerequisites and their elimination

In the near future, the gasoline trimmer for the grass got the status of the 1st of the main tools in the arsenal of summer residents. And this is logical, because a motorized braid for grass allows you to quickly put a personal plot in order. But from time to time it happens that a trimmer for grass does not start hot and even cool. In such situations, it is necessary without the help of others to establish the cause of the malfunction. Let’s find out what to do if a trimmer does not start for grass. The prerequisites, which more often lead to such troubles, will be considered further.

Redverg RD-GB252 Operating Instruction Institution-page 9

Instruction Redverg RD-GB252 for the device trimmer for grass gasoline contains pages in Russian.

Бензиновый триммер RedVerg Basic GB52C

You can download PDF file of this instruction: download pdf

Gas tank cap; 2. Fuel tank; 3. Lever adjustment of the position of the throttle; 4. Spark plug; 5. The primer of the swing of the fuel mixture; 6. Air filter unit; 7. Carburetor; eight. Starter handle; nine. Switch; ten. Accelerator lock key; eleven. Accelerator lever; 12 right engine control handle. Before starting the engine, make sure that all elements of threaded joints are securely tightened and the cutting tool is correctly installed and fixed. One. Place the unit on a flat fixed surface. Place the head with a cutting tool away from any objects. 2. Fill the fuel tank (2) and tightly tighten the lid (1). 3. Guided by p.3.2. This instruction set the lever of the throttle position (3) to the “Closed” position. 4. Download fuel to the carburetor (7), pressing several times on the primer of the swing of fuel (5). 5. Using the accelerator lever (11) and the keys of the accelerator block (10), set the switch (9) to the “Start” or “I” position depending on the design of the switch. 6. Sharply pull the launch cable of the starter (8), after eliminating the free move. Repeat until the first characteristic exhaust through the silencer. 7. Transfer the lever adjustments to the position of the throttle (3) to the “Open” position. Eight. Run the engine by repeating the actions of p. 6. The engine should earn at high speeds. Nine. With a single press on the locking key of the accelerator lever (10) and the accelerator lever (11), the engine is transferred into idle speed mode. The instrument speed is regulated by pressing the accelerator lever. When the engine operates at idle, the cutting tool should not rotate. It is forbidden to fully pull the starter cable when starting the engine. Damage arising from such actions is not provided by warranty repair! Eight.3. Turning off the engine. To turn off the engine, you need to turn off the accelerator lever and the switch (9) transfer to the “Stop” or “O” position. The engine will stall. After stopping for a short period of time, the engine can be launched when the throttle is opened.

See also  How to fasten a disk to a trimmer. Instructions on how to use a gasoline trimmer learning to start a tool

Nine. Benzotrommer’s exposure. Nine.One. Speasing of grass. Make sure the device is balanced between the engine and the cutting tool. The cutting tool should move parallel to the Earth and not demand the efforts of the operator to hold it in the work position. Always transfer the benzotrimer so that the cutting tool is below the level of the belt and as far as possible from yourself and others. Always transfer the benzotrimer so that the cutting tool is below the level of the belt and as far as possible from yourself and others. Recommended width of the mowing strip. 1, 5 meters. When using a disc for mowing grass or

start, trimmer, grass, gasoline, redverg, tool

Manual launch of the snowman engine

Now to the question of how to start a snowboard with a manual type of launch.

If you have a snowmobile machine of the budget category, then a hand starter will probably be installed on it. This is not the worst option. Just objectively electric starters are much more convenient and easier to operate.

Learning to run the motor with a hand starter is not difficult. Here you should comply with some requirements, as well as follow the instructions:

  • A prerequisite before starting starting is a check of the current level of oil in the system. If it is not enough, you need to add grease. If the oil is old and has signs of wear, then replacement is required.
  • When everything is in order with the oil, you can lower the levers that block wheels, as well as the screw mechanism.
  • Further, the lever responsible for the supply of fuel is transferred to an open position.
  • Now you need to fix the cap of an electric wire in a static position.
  • The next step is the closing of the throttle. The throttle of the throttle must be in the closed position.
  • Next, the starter is activated. It needs to be transferred to the appropriate position.
  • Then the operator needs to pump up a certain amount of fuel. This is done manually by pressing a special button several times.
  • Now the user should pull the starter cable. This is done until the resistance is felt.
  • It remains only to sharply jerk behind the cable, which will ensure the launch of the engine on the snowman.
  • In the final stage, you need to transfer the throttle to the open position.

As well as the previous case, where an electric starter was installed on snowmakers, if there is a manual starter, the engine also needs to give time for a full heating after starting.

There are those who immediately start work after launch. This is a common and fairly serious mistake, since an additional and strong load will act on the unenfustified motor. This can adversely affect the resource of the motor, its integrity and stability of operation.

Therefore, gain patience, wait 5-7 minutes so that the snow drunkard engine reaches the optimal operating temperature, then proceed to cleaning snow and cleaning the territory.

Lugging a lawn mower

Here you will find information on how to properly care for all parts of the equipment, how to adjust, how to disassemble and how and how to lubricate a lawn mower (moving parts).

Engine. Follow the cleanliness of the air filter, foam products should be moistened with oil. The fuel filter needs to be checked at least 1 time per week and in the event of a malfunction in a timely manner. The silencer and candles should regularly clean up from the carbon fiber (as they become contaminated). Before each start of operation, the tightening of all screws and nuts should be checked.

The corner gearbox should be cleaned of dust and pollution as necessary, as this interferes with effective cooling, and then lubricated with any lubricant for the gearbox, for example, STIHL.

Trimmer head with fishing line. The mowing head should be cleaned after each use of a trimmer for grass, and also replace it in a timely manner as soon as the deformation or crack. Only a special cord (fishing line for trimmer) for trimmers, no cables or wire must be used! The diameter of the fishing line should be the way the specific model. The cord winding should be carried out tightly, but without the intersection of threads.

See also  STIHL chain saw does not start well in cold conditions

Cutting equipment (saw disk or knife). Metal products must be sharpened (for this there are special templates and files) at a special angle. Bilateral models are desirable to turn over time for uniform wear. Devilled or incorrectly sharpened discs and knives lead to engine overload and reduction in the life of operation.

Protective covers should always be worn during a mowing. They cover the operator from flying grass and stones from under cutting equipment, and also reduce the load on the engine. After work, thoroughly clean the internal and outer surface of the casing with a stream of water or a soft cloth, trying not to scratch the surface.

How to fix a disk or a fishing line for a trimmer on a trimmer

The cutting mill is attached to the executive organ. The mounting location is called a gearbox. It is not difficult to cope with the task of installing a disk or coil. The principle of consolidating cutting discs on the trimmer is as follows:

  • The figured washer is originally fixed by using a hexagonal key
  • On the shaft set the disk
  • Then install the upper washer, and then tighten it by means of the fastener
  • It is necessary to rotate the nut through a special end key, which is usually equipped with each tool
  • The rotation of the nut is carried out in the direction counterclockwise
  • When rotating, it is necessary to jam the shaft with a hexagonal key

In the opposite sequence, the disk on the trimmer is removed and replaced. Details on how to install a coil with a fishing line on a lawn mower is described in this material.

Inspection of the reducer of the lawn mower and its lubrication

Checking the gearbox before starting a gasoline trimmer for grass must be carried out on a regular basis. The lack of lubrication or its small amount increases the friction of the gear gear of a gearbox operating at fairly high speeds. As a result, overheating and gears occurs. Motokosa gearbox fails. To prevent the occurrence of such a breakdown during operation and the regular inspection helps.

If, before the launch of a gasoline braid for grass, an insufficient amount of lubrication in the gearbox or its absence in the case is laid “litol”. To do this, it is necessary to unscrew the screw on the bend of the gear housing and the “lilest” in the amount of 1-2 ml.

Working with a gasoline trimmer for a long time, every 8-10 mothers add grease to the gearbox of the bar.

Rules for the operation and storage of a lawn mower

In order for the lawn mower to start well and continue to provide it with good storage and operation conditions:

  • During operation, carefully monitor the cooling system, carefully and in time, clean the channels in the case, as well as the ribs of the starter;
  • If necessary, use solvents, kerosene and other detergents for cleaning;
  • Do not clean the “hot” tool. Let it cool;
  • Stactly comply with the requirements of the instructions for the operating mode, otherwise you can overheat the engine;
  • If you do not plan to use the lawn mower in the next month, the fuel mixture from it needs to be drained, t. To. Over time, it breaks up into heavy fractions, which will definitely clog the channels of the carburetor;
  • After draining the fuel, let the trimmer work at idle until it stalls, this will help to completely remove the rest of the working mixture.

Before winter storage, take the following steps:

  • Completely disassemble the braid, rinse and clean all the details you can;
  • Inspect the details for damage, if necessary, eliminate distortions, impulses, bent and any other malfunctions;
  • Pour a sufficient amount of oil into the gearbox and clean the air filter;
  • You can partially disassemble the motor, rinse, blow and smear all the moving parts;
  • In order to lubricate the piston, you need to unscrew the candle, raise the piston with the outlet to the extreme dead point, pour a little oil into the candle hole and scroll the crankshaft a couple of times;
  • If you store the lawn mower not in the house, wrap the engine with an oiled rag.

Remember, careful compliance with the rules will allow you to forget that the lawn mower is bad for several seasons.

| Denial of responsibility | Contacts |RSS