How to tighten the spring of the chainsaw starter. Device

How to make a repair starter with your own hands

The appearance of various starter malfunctions leads to the lack of the opportunity to start a chainsaw. The most frequent breakdowns of the starter include:

To eliminate each of these malfunctions with your own hands, certain tools will be required. There must be a set of screwdrivers and a spare cable with you. You need to extract and inspect the starter for the chainsaw in the following order:

  • To find the cause of the breakdown, the starter from the chainsaw will need to be removed. To do this, unscrew the screws with a screwdriver with which the protective cover with the starter attached to it is held;
  • After removing the lid, it is necessary to gently unscrew the screw through which the starter is attached to the protective cover;
  • Then you need to try to smoothly start the starter. For this, remove the spring and clamps from it;
  • Next, a coil with a cable is removed from the starter for the inspection.

As a result of the inspection, you can find a number of typical malfunctions. These include:

  • Various damage to the pulley in the form of tears or cracks mainly in the back of the part. They interfere with the normal operation of the entire starter;
  • Damage to the starter spring of lightweight launch. In such cases, not only the spring itself can be faulty, but the place of its fixation is the most vulnerable part of the spring;
  • Damaged by the dog Starter flywheel.

In any case, any faulty part should be completely replaced by a new spare part.

Clutch repair: process nuances

With independent maintenance of clutch couplings, you need to know that:

  • Several saws have a puck that is located between an asterisk and a clutch, and an asterisk and a motor. Consider this when repairing;
  • The special firing of the oil pump drive should not be damaged during disassembly, and is also subject to return to the original position. Otherwise, the chain will not receive a lubricant or even cease to be lubricated.

The tool that has visited the repair must undergo a check for the reliability of bolted screeds, the supply of lubrication to the circuit and the serviceability of the motor (it should smoothly turn on and work smoothly). Only after that can it be operated.

tighten, spring, chainsaw, starter, device

Typical breakdowns and repair of the chainsaw starter

The appearance of various starter malfunctions leads to the lack of the opportunity to start a chainsaw. The most frequent breakdowns of the starter include:

To eliminate each of these malfunctions with your own hands, certain tools will be required. There must be a set of screwdrivers and a spare cable with you. You need to extract and inspect the starter for the chainsaw in the following order:

  • To find the cause of the breakdown, the starter from the chainsaw will need to be removed. To do this, unscrew the screws with a screwdriver with which the protective cover with the starter attached to it is held;
  • After removing the lid, it is necessary to gently unscrew the screw through which the starter is attached to the protective cover;
  • Then you need to try to smoothly start the starter. For this, remove the spring and clamps from it;
  • Next, a coil with a cable is removed from the starter for the inspection.

As a result of the inspection, you can find a number of typical malfunctions. These include:

  • Various damage to the pulley in the form of tears or cracks mainly in the back of the part. They interfere with the normal operation of the entire starter;
  • Damage to the starter spring of lightweight launch. In such cases, not only the spring itself can be faulty, but the place of its fixation is the most vulnerable part of the spring;
  • Damaged by the dog Starter flywheel.

In any case, any faulty part should be completely replaced by a new spare part.

Dismantling, disassembling the starter of a trimmer for grass, replacing parts

First of all, the repair process begins with the removal from the trimmer for the grass of the entire starter. This process is inherently not difficult and will only require twisting several screws with a suitable locksmith tool. It should be noted that when dismantling the mechanism of launching the lawn mower, it is necessary to observe safety precautions, since the strip spring in a compressed state has sufficient energy to injure a person.

Parsing the starter motorcycles

This stage allows the master to establish the reasons for the failure of the launch unit, as well as to defect individual parts. The disassembly work should be performed in the following sequence:

Eliminated spring from a starter coil

Many experts note that the first time the installation of the spring is quite difficult, because the owner when repairing the starter of the trimmer for the grass will need not only the basic skills of the locksmith, but also patience.

The sequence of assembly of the starter of the trimmer for grass

Although the process of assembling the launch unit of the lawn mower is carried out in the reverse analysis of the order, there are several nuances that should be paid special attention to:

    The coil with the spring installed must be turned and mounted in the groove of the starter case so that all the protrusions become in their original place.

Installation of a trimmer coil for grass in the starter case

When assembling the starter, pay attention to the compression spring, which on both sides should be limited by steel springs. If this is not done, then after the first season it will rub the grooves in the pulley case.

Recommendations for stretching the strip spring

After installing the starter, it is necessary to dismantle the rope handle and insert it into the groove of the coil. Further, against the move of the pulley when starting, it is necessary to make a certain number of revolutions specified in the operation of the gasoline trimmer for the grass. It is worth noting that on how to put the spring on the trimmer and how the tension will make the tension and further performance of the node depend. At the final stage, we spread the rope into a special hole and fix it with a handle.

tighten, spring, chainsaw, starter, device

Replacing the rope of the starter of the trimmer for grass

At the very beginning, it is necessary to extract a broken cord, select a suitable length depending on the trimmer model for the grass. We extend through a special hole in the pulley and at the other end we tie a knot in order to prevent jumping out the rope from the trimmer starting mechanism for grass. Next, we build a strip spring to the required number of revolutions and mount the handle.

See also  A device for sharpening chainsaw chains with their own hands

How to assemble a starter on a chainsaw?

After replacing the faulty elements of the starter, the turn of its reverse assembly comes. In this case, it is necessary to observe maximum accuracy, since the slightest discrepancy can lead to a breakdown of the starting mechanism. The assembly of the node should be performed in the following sequence:

  • The standard cable will need to be tucked into the factory hole of the coil. The cord, at the same time, does not need to be wrapped;
  • Next, you need to insert the coil to its base place. At this stage, many newcomers make a typical error. On the surface of the coil there are 2 slots. A full.Time hook of a spiral spring should get into one of them. To do this, the coil will need to be installed in such a way that it rises tightly in its original place, and the existing hook hit exactly in the slot. The correct installation must be checked by scrolling the coil along the hour of the clock until the resistance appears;
  • Then you need to install the device of lightweight launch of the chainsaw. In this case, the ledge of the latter should be located in the seizure of the installed coil;
  • After that, you will need a screw and a washer to fix the device;
  • Next, the second end of the cord must be tucked into a special outlet;
  • At the next stage, you will need to refuel the cable into the launch handle. For this purpose, at the end of the cord, you will need to tie a medium.Sized knot. If it is too small, then the cable will slip, which is why it will quickly wrap up on the drum of the starting mechanism;
  • Then you need to release the loop inside the starter. Immediately after this, the rotation of the starting mechanism during the watch arrow should begin. In this case, the cord does not need to be wrapped. Next, the coil will need to be fixed with your hand, and stretch the loop by the handle out;
  • After that, you need to check the operation of the starting mechanism;
  • If the knot works properly, it will remain to install it on the tool, and attach it with three screws.

Starter repair. The procedure is not complicated if you adhere to the correct procedure. As a rule, replacing the starter cord will take no more than 20 minutes. The main thing is to properly place the pulley and the drum in relation to each other. Otherwise, the trigger will not work.

Chainsaw Recoil Starter Spring Repair (Ergostart Model). Stihl Ms230 CHAINSAW.

If it doesn’t work out

Когда все действия выполняются согласно установленному порядку, а бензопила не начинает работу, значит есть сбои в ее механизме. Typically, the cause of this phenomenon is common and easily eliminated problems, such as the lack of spark, overlap fuel, clogging of the filter that passes the air. In order to start a chainsaw, you will have to find the reason and perform the necessary actions to eliminate it. The rules must be followed should only be carried out correct actions. If a person does not know what to do, there is no need to commit rash actions

It is forbidden to disassemble the device, especially carefully you need to handle the carburetor. You can not unscrew any screws on it, since if its device causes a breakdown, then it is impossible to fix a chainsaw without professional equipment

The actions that need to be performed in strict order are listed. How to make a chainsaw without a starter correctly. Only when moving from one event to another can you determine the exact cause of the malfunction and quickly eliminate it without damaging other details. The algorithm of actions performed in case of failure in the chainsaw establishment:

  • First, let the device take a rest. This is especially true for the saw that were in operation recently. It is enough to wait for no more than 10 minutes, since during this time the mechanism will cool and in the absence of other breakdowns will easily start. How to get a chainsaw of various Urals, friendship without a starter cannot be started by a chainsaw. Sometimes it happens that during the establishment a candle is poured at the device. If this unpleasant property has occurred, then it is enough to wait for a very small pause and repeat all the actions for the motor factory again.
  • The hull cover is unscrewed from the device for taking out the air filter. The process of the device is performed in the absence of it. Sometimes the reason for the lack of ignition is that the filter is contaminated. If the ignition occurs without it, then the reason lies in this. To eliminate these troubles, it is enough to wash the filter under running, warm water and soap, then dry out. You can also replace the old element with a new.
  • The spark plug is removed. The spark is checking. If it does not appear, you need to replace the old candle with a new. This usually helps and the spark appears, but in some cases there is no sparks when replacing the mixture.

This means that the ignition unit is spoiled, and the chainsaw needs professional repair. Sometimes the ignition block is also in the presence of a spark, so this criterion cannot be guided to eliminate the likelihood of a breakdown.

When a spark appears if it is impossible to force the device to work, it is necessary to continue to perform the actions described below.

There are times when the spark manifests itself, but the candle itself is moisturized. This is possible if gasoline enters it. To get rid of it, it is enough to turn the device so that the cylinder is released down. Then the whole excess fluid will spill. Next, check the combustion chamber, for which it is necessary to twitch the starter more than 10 times. A spoiled candle can be tried to replace with a subsequent check of the effectiveness of its work. If it becomes faulty, you can replace this element with a new. After these actions, you need to try to activate the operation of the device again.

Sometimes the candle remains dry. In this case, it is necessary to dial a gas mixture into the syringe and let it into the cylinder. After that, you should immediately try the device. If the cause of a long absence of a reaction to attempts to include is garbage in a carburetor, then when removing it should not interfere with fuel intake into the combustion chamber. The mechanism of successful garbage harvesting is determined by the fluid flow when filling the gas mixture, so you need to pour fuel with force, and then almost immediately try to start the device. The muffler is removed. How to start Stihl, launch of the stihl chainsaw, how to properly start the Stihl 180 chainsaw. First launch of the video Original chainsaw STIHL MS 180. Sharpening the saw chain STIHL MS 180. To do this, it is unscrewed and carefully removed so as not to deform the gasket that delimits it from the engine. You need to try to perform an institution of the mechanism without the use of an air filter and muffler, which helps to eliminate breakdowns in these structural elements.

See also  Where is the fuel filter in a chainsaw?

With any damage on the walls of the cylinder, we can conclude that it will have to be repaired by professional methods or replacing it with a new. Typically, such malfunctions are led by insufficient concentration of fuel oil.

Removing and disassembling the starter, replacing broken parts

To repair the starter of the trimmer for the grass, you will need to disassemble it first, and then collect it. This process is not a particularly difficult occupation. For work you will need screwdriver with the tip of the desired shape

Everything should be done carefully, observing safety precautions, mainly that the spring does not injure the master if an accident.

Parsing the starting node

They disassemble the launch mechanism in order to install new parts instead of broken in the following sequence:

  • Spin a screw with a screwdriver, fixing the pulley with a starter lid;
  • Take out a spring and antennae;
  • Remove carefully with the pulley (you need to unscrew the head or work, having dressed the glasses and gloves before);
  • Determine why the launch mechanism has broken;
  • If the spring collapses almost completely, then it is replaced;
  • When the spring exits from the hook, it is installed in the original place, bending the antennae before this (the photographs show the laying process);
  • After the spring plate is installed inside the groove, it is carefully twisted.

To change the spring, you should work carefully and accurately: it can, under the influence of the effort caused by the installation of it in place, accidentally burst. Even if you carefully remove the video, then the spring strip flies very quickly from the coil and can injure your hand with its sharp edges.

Immediately putting a springy plate in the same place does not always work. It often slips, so attempts are required to repeat until the desired result is achieved.

Starter assembly

The assembly of the starting node is carried out in a number of stages:

Chainsaw Repair. Replacing the Starter Recoil Spring (Poulan Part # 545008013)

  • The coil is turned over, installing it so that the spring bend exactly stands into the groove of the case, as in the photo below;
  • Lay two washers between which a spring is placed;
  • Put in place a cup of antennae;
  • Twist the screw (photos below).

When making the stated manipulations, it is imperative Put two goals

If this is not done, then the spring over time damage the plastic cup, and when it is pulled. Because of this, a feeling appears, as if the spring had flown. To eliminate such a drawback, you need to install this part of a larger length or an additional goal.

When such spare parts are absent, you can just a little unscrew the screw

, And the starter knot will begin to work without shaken. But this option is temporary. It is better to repair qualitatively as quickly as possible.

Spring tension

After installing the spring, it should be pulled. The following actions are performed for this:

  • Remove the handle from the starter cord;
  • Then the rope is inserted into the coil groove;
  • They stretch the spring, rotating the coil in the direction opposite to the clock of the clock arrow (reviews);
  • Make the desired number of revolutions specified in the instructions for the use of the trimmer model used and the corresponding length of the cord used;
  • At the very end, the rope is threaded into a hole designed for this, located in the starter cover;
  • Put the handle in place, fixing it with a node.

If after repair The spring continues to fly

, then you can get rid of this in the following ways:

  • Squeeze the suitable piece of the plate into the groove at the location of the spring hook;
  • Drill holes on two sides of the groove in the coil, into which the spring hook is inserted and fix it using a wire.

Replacing a torn cord

A torn rope is replaced in the following sequence:

  • The old cord is removed;
  • Choose a suitable rope (thickness and length);
  • Having reached it through a special hole in the coil, a knot is tied;
  • Sprinkle a spring, producing the required number of revolutions;
  • Fix the pen.

It is better to stretch the spring plate along with the partner so that the edge of the cord does not hit the starter mechanism.

It is easy to assemble a starter on a trimmer and wound a spring, only you should do it carefully and with caution. For different models, the gas tanks of the launching mechanisms are the same, so they are repaired in a similar way. In this case, there are some nuances associated with their constructive features.

Starter repair for gasoline, gasoline, trimmer for grass with your own hands

Whatever high.Quality gasoline tool you use, in the process of construction, everything can happen to it at the most inopportune moment for this. Often there are problems due to the starter rupture. It happens that you can drill holes on a gas station to install the columns of the fence or cut the grass with a trimmer for grass grass, start starting the device and only have time to pull out the starter handle a couple of times, since the rope breaks and the engine has already started, wrapping it up. The rest of the cord to the flywheel, tearing off the pulley. Take it to the new store. But these, of course, are extremes.

Today we will consider the most common case when a breakdown is not so serious, and we will show how to repair the starter with our own hands, if the cord breaks off without any destructive consequences or winds due to the fact that the spring inside simply flew, turned off. At least initially I would like to believe in this. But in order to find out, whether it is or not, it will be necessary to disassemble the starter.

Diagnosis of the starter of the chainsaw

Due to the long.Term operation of the chainsaw, the start.Up mechanism becomes unusable. After one or more jerks when tearing the rope of the starter, the crankshaft does not turn. This problem can be determined by the following reasons:

Before starting work on the diagnosis and repair of the start mechanism, it is necessary to prepare the necessary tools and accessories that will significantly reduce the time for operations. These include:

  • A set of locksmith screwdrivers and a specialized set of corporate instrument, which is included in the setting set of a chainsaw.
  • Durable cord for replacing the worn.Out launch rope.

At the first stage of the repair of the starter of the chainsaw, it is necessary to identify the nature of the problem. To do this, remove the side cover from the side of the starting mechanism, while unscrewing only a few screws. Depending on the manufacturer for this operation, a specialized or ordinary locksmith screwdriver is needed.

See also  How to sharpen a chainsaw chain yourself. Sharpening device

Next, we examine the inside of the protective casing. In the absence of cracks and chips of plastic, we proceed directly to the diagnosis of the launch unit. Unscrew the central bolt of the starter and dismantle the spring. Cracks and impulses should not be observed on its surface. It is problematic to choose independently in effort and number of turns, so the help of specialized centers will be required.

After removing the clamp and the spring of the starter of the chainsaw for dismantling, a pulley with a wound cord is available. The integrity of the rope indicates that it is necessary to carefully review each of the details of the launch mechanism.

Block: 2/4 | Summer characters: 1749

How to put a starter on a chainsaw correctly

How to start a chainsaw: a couple of effective ways

Chainsaws are characterized by constructive features, but in most cases the assembly principle is carried out in accordance with two standard schemes. Many devices in the manual contain information about the need to turn on the emergency brake before the start of the turning on-off procedure.

First, it is necessary to master the installation of the plant and study the main methods of eliminating the failures, then a person will have the opportunity to fully control the device.

tighten, spring, chainsaw, starter, device

Briefly about the installation of the plant

Chain saw works from. This is a simple device whose design does not have special bells and whistles. Usually it works normally even in harsh conditions.Feeling the factory to get acquainted with structural elements:

  • Carburetor engine (see. Carburetor adjustment).
  • Cliper clutch of centrifugal type.
  • Ignition system, almost contactless in all devices.
  • Carburetor that adds air to the fuel mixture.
  • Fuel system. Its standard device consists of a hose, a filter and a gas cylinder, but sometimes it also has additional details.
  • Starter.
  • Tyr.
  • Chain (see. Oil for the chain).
  • Tension mechanism and chain brake (see., How to focus the chain).

Step-by-step instruction

With an activated brake, the assembly process occurs much slower, therefore it is also safe and convenient to turn on the gear without using brake equipment.

If a person is not confident in his knowledge and accuracy, then the brake should be activated the other way around. If the procedure is correct, the device does not start, the mechanism does not make dangerous for human actions.

1 diagram of the standard mechanism

  • Before starting benzoil, you need to move the damper, which acts as a control lever, to the bottom, compared to the optimal position. First click the button responsible for the gas supply. Only if this condition is fulfilled, you can normally move the damper to the lower stop.

Starter handle twitches again until the system starts. When the device begins to work actively, high speed becomes noticeable, since the throttle is at a high level. It should be remembered that sometimes chainsaws are delivered without a starter, then all actions are performed with this element.

In our rating, chainsaws in quality, you will find all the chainsaws with the optimal ratio of price and quality.

Our article will also help you make a choice in favor of a particular chainsaw brand.

Basil is produced in Russia. Low price with sufficiently high quality.

2 diagrams of the standard mechanism

  • Ignition is included. To do this, transfer the toggle switch to the desired position or move the switch.
  • Usually you need to press on the ground for pumping more than two times. Gasoline is poured into it, after which it is necessary to press the device more than three times.

You need to take the starter handle and tighten with sharp movements until the ignition process is heard. It is marked by the institution and almost instant off the engine of the engine. Then the flap should be assigned to the starting position, checking its reach to the stop.

Again, the starter handle twitches to the location of the device. Before conducting this action, you need to make sure that this particular method will help to get a chainsaw. Some devices have a new ignition system.

Repair of the starter of the chainsaw. With your own hands.

How to make a starter on a chainsaw yourself? How to bend a spring at a chainsaw starter? How to wind a spring

DIY chainsaw starter repair

Starter for a Chinese chainsaw 5 pieces link-

tighten, spring, chainsaw, starter, device

When the device constantly stops, you need to systematically restart it (see., What to do when a chainsaw stops when pressing for gas). After some time, the engine will gain an impulse and will be able to maintain active work without interruptions.

To obtain additional information cm.

If it does not work out

Когда все действия выполняются в соответствии с установленным порядком, и бензопила не начинает работать, тогда в ее механизме возникают сбои.

Usually common and easily eliminated problems, such as the lack of spark. The clogging of the filter passing through the air is the general causes of this phenomenon. To start a chainsaw, you will need to find the reason and take the necessary steps to eliminate it.

The rules must be observed, it is necessary to perform only the correct actions. If a person does not know what to do, a person does not need to make a rash. Dismantling the device is prohibited, especially with caution should be treated with a carburetor.

Do not spin the screws on it, as if its device caused a breakdown, then without professional equipment it is impossible to repair the chainsaw.

Lists the actions that must be performed in strict order. Only when moving from one activity to another can you determine the exact cause of the problem and quickly eliminate it without damaging other details. The algorithm of actions performed in case of failures in the creation of a chainsaw:

  • Firstly, this is enough for the device to remain. This is especially true for the saw that have been in operation recently. It is enough to wait no more than 10 minutes, since during this time the mechanism will cool, and in the absence of other cliffs, it will easily begin. Sometimes it happens that during the institution a candle is poured on the device. If this unpleasant property has occurred, then it is enough to wait a very short pause and repeat all the actions for the engine winding again.
  • The hull cover is unscrewed from the air filter removal device. The process of landing the device is performed in its absence. Sometimes the reason for the lack of ignition is filter pollution. If ignition has occurred without it, then this is precisely the reason. To eliminate these problems, it is enough to wash the filter under the run, warm water and soap, and then dry. You can also replace the old element with a new.
  • The spark plug is removed. There is a spark test. If it does not appear, you need to replace the old candle with a new. This usually helps, and a spark appears, but in some cases, and when the mixture is replaced, there is no spark.
| Denial of responsibility | Contacts |RSS