How to trim a skirting board

How to cut a ceiling plinth. Basic Ways

Upon completion of the repair, it is very important to exclude the presence of defective parts that spoil the overall appearance of the result of the work. Such nuances include the question of how to properly cut the ceiling plinth.

After finishing, there may be gaps between the walls and the ceiling. To close them and create a pleasant appearance of the interior, it is necessary to use a skirting. It is accurately glued with the help of liquid nails along the perimeter of the room near the ceiling, and after that the ceiling plinth in the corners is trimmed.

There are several options on how to cut the ceiling plinth.

Using a power plier

This device is a small tray with holes (vertical) designed for the hacksaw. There are special 45 and 90 degree marks on the jigsaw. The workpiece (ceiling plinth) must be placed inside, fixing the value of the desired angle. Then the hacksaw is inserted into the vertical slots and the skirting is cut.

The problem may be that the angle of the ceiling plinths are of 2 types: external and internal, and it is worth considering when trimming them with a plough.

For the inside corner, the process is as follows.

So, the side of the skirting board, which it will be attached to the ceiling, should be placed at the bottom of the tool, and the opposite side of this strip should be pressed to the left hole in the plough. Then it is necessary to cut a corner, put a new (received) product with the first, to check whether the cut parts coincide. If not, it is possible to very accurately correct an error with a knife. Or, if the discrepancy is very small, it can be disguised directly on the wall putty, but will need to pick up a similar color.

To cut the skirting boards in the outer corner, proceed as follows.

The side of the original piece with which it is attached to the wall is placed at the bottom of the jigsaw, and the opposite side is pressed to the right hole in the jigsaw. Then you can cut the corner with a hacksaw or a box cutter.

trimming without the help of a joiner

This method is used if you do not want to spend money on repair tools, buying it only for the baseboard.

All you need in this case: a pencil, a ruler and a box cutter.

Here, as well as in the first method, everything depends on the type of angle.

The plinth, which will be fixed to the right of the corner, is applied to the ceiling surface. Along it, along the outer edge of the plank, a straight line is drawn. Then the same process is repeated for the opposite side of the corner. At the intersection a mark is placed. After that it is transferred on a plinth which is put to a corner, and then, from it down to an edge of a plinth, the line on which it will be possible to cut a corner of a ceiling plinth with a saw or a household knife is spent.

For the outer corner, the process goes like this:

The skirting board is placed to the right of the corner. A fishing line is drawn along the skirting board along the ceiling surface further from the corner. Then the skirting board is attached to the left side of the corner. A line is drawn in the same way along the skirting board up to the intersection with the first segment.

After that two marks are copied on the initial product: the obtained intersection of lines and designation of the room corner. If you connect these two points together, you will obtain the distance by which you need to shorten the skirting board. Then we get the baseboard cut with a hacksaw or office knife. If there are some small gaps, they can also be sealed with putty.

Using a false chisel

This tool is made in 2 variants:

1) Two lines parallel to each other are drawn on cardboard or on heavy paper, then the required angle is marked using a protractor. The fixture is ready. Then the baseboard is fixed in the false fishing rod, marks are put, on which the angle should be cut.

2) A false molding can be made using 3 planks of wood. To do this, you need to fold them in a “U” shape and make marks of 45 and 90 degrees.

When working directly with the fixtures described above for the first time, it is important not to make a mistake. It is therefore necessary to cut the ceiling plinth in the corners with at least 10 cm to spare. This is a kind of safety net. In any case, the original material can always be corrected, but the cut material cannot be returned to its place.

By following the simple instructions in this article, you can understand not only how to cut ceiling skirting boards, but also how to do it neatly. What methods to follow and what to pay attention to. If there is a possibility to send part of the budget to buy a special device, then do it, in the opposite case. save money and ensure the process completely with your own hands.

How to Trim a Wood Baseboard While Installed on the Wall : Trim Installation & Maintenance

How to trim a ceiling plinth can advise and consultants of repair stores. Useful tips can also refer to certain nuances of the room being repaired. For example, how to properly trim strips in rooms where the corners are not exactly under 90 degrees.

It is also possible when a mistake is made during the repair process. For example, the main tip on how to cut the ceiling plinth (with a margin of 10 cm) is not taken into account. In this case, you need to find a pattern in the store, suitable for the concept of the room, which is just to close the gap between the planks.

How to properly trim a ceiling plinth

This is the perfect ceiling plinth you can make with your own hands, if you follow these instructions.

For the manufacture of ceiling skirting boards are mainly used three materials, these are:

Still make stucco ceiling cornices, but that’s another topic.

  • The most fragile and cheapest of them is foam, although the strength of the ceiling is not very necessary and.
  • Styrofoam is much denser it can be easily cut with a knife and, of course, it is more expensive.
  • Wood is the hardest to work with. In order for the corners of wooden baseboards to be perfect, it is necessary to use only a fine-toothed hacksaw, or even better a hacksaw for metal and a sanding sandpaper. Only in this case it is possible to achieve an even angle

Trimming the ceiling plinth with your own hands

trim, skirting, board

Let’s review step by step how to properly cut the corners of the baseboard (also called baseboard fillet). In the vast majority of modern apartments corners of rooms and other rooms are equal to 90 °. Cut the ceiling skirting must be at an angle of 45 ° or 90 °. How to cut the ceiling plinth? A special tool is used for this, which is called a plier. In this tool are already made slots at an angle of 45 ° and 90 °. At first glance it seems a simple task to cut the skirting. But the fact is that he glued to the ceiling at an angle of 38 ° to 45 °, which means that the trimmed corners will not join, leaving gaps. To prevent this from happening, and is used a wire cutter.

Cut inner corners with a hook

To do this you will need the following tools:

  • Tack is placed on the bottom of the chair with the side that will be glued to the ceiling, and the underside is pressed against the wall of the chair, to the right of her slot.
  • Trimming the tape is made with a hacksaw or sharp knife. Cut carefully, without excessive force so as not to deform the ceiling tile and not to create chips.
  • In such a way we cut the adjacent corner of the baseboard, but already using the left-hand slot in the wood mill.
  • Then these parts are attached to the corner to check if there is a gap, you can trim with a knife.

Tip.In order not to transfer the material in vain and to acquire skills, train first on small pieces.

How to fit the skirting board into the mortiser

Cut the outer corners with the wood chisel

  • Put the skirting board at the corner and mark the place on the skirting board where the outer corner begins with a pencil.
  • Then place the skirting board in the skirting board frame. The side that will be attached to the ceiling, laid on the bottom of the chair, and the other side pressed against the wall.The mark on the skirting board should be near the left-hand slot. Cut one edge.
  • Then cut the other half of the corner in a similar way. Only the mark on the skirting board must be near the right-hand slot.

We put both halves to the corner and check whether there is a gap. If everything is OK, you can glue the skirting board in place.

How to cut a skirting board without a mitre cutter Trim the skirting boards for the inside corner

If you don’t have a jigsaw, you can get by without one:

  • Then put the skirting board on the ceiling the way it should stand, and run a fishing line along the ceiling.
  • Then we put the skirting board to the ceiling to the right of the corner and run the second line.
  • At the point where the mowing line crossed, make a mark on the baseboard and guide the line from the mark to the bottom corner of the baseboard. This fishing line will be the trim line for the skirting boards.
See also  What is the best way to cut a plastic skirting board?. Sawing corners of skirting boards

Marking for trimming the left-hand corner of the skirting board

Do the same with the left corner. Trim strictly along the lines with a sharp knife.Then place it in a corner and check to see if there is a gap. If there is a gap, we carefully trim the corners. The skirting board can then be glued in place.

Tip. Do not use excessive force when trimming the skirting board. It can crumple and deform after you glue it in place after the glue dries.

Marking for trimming the right-hand corner of the baseboard without the jigsaw

You can easily cut the fillet for the outer corner without the joiner:

  • To do this, attach the ceiling batten as it should stand to the right of the corner. Guide the fishing line with a pencil across the ceiling further away from the corner.
  • Then we attach the fillet to the left of the corner and draw a fishing line along the ceiling until it intersects with the first line.
  • On the fillet do marks at the intersection of the lines and in the place where the corner of the room.
  • Connect the marks with a line on the fillet and cut with a sharp knife. The cut should go inside the fillet.
  • Check the joint at a corner, trim it if necessary, and glue the skirting board in place.

It should be noted that for 1 linear meter. Count the number of meters in your apartment, multiply by 100. This will be the amount you can save if you do the job yourself.

What??? Pros Cut Baseboard Upside-down and Vertical Why?

How to trim a ceiling molding correctly?

Trimming a ceiling skirting board properly. how to do it?

Ceiling plinth. a decorative boundary between the walls and the ceiling. But it is often used to mask the joints of finishing material on the wall and ceiling, if it is not made accurately, or has a different structure.

Many people wonder how to properly cut the ceiling plinth, because without it the design of the room seems unfinished. Glues this element simply. on a special glue. But the trimming of the ceiling plinth in the corners, so that they look presentable and neat, some may put in a stalemate. There are rooms with a complex layout, which should be equipped not only the inner corners, but also external.

This question can be answered accurately, if you know what material is made of this decorative element. There are four types of baseboards:

The cheapest option is foam baseboards. But this is a very delicate material, it can appear creases and dents, even from the fingers of the hands, if you press it harder, so it is very difficult to cut the corner of the ceiling plinth from this material accurately.

In most cases, an inexperienced person throws away a lot of material for this reason. They are electrostatic, and attract a lot of dust. They are cut with a regular office knife. You can also cut with a hacksaw with fine teeth, but there is a chance of getting an uneven edge.

Polyvinyl chloride is one of the inexpensive materials, it is brittle and can crack when cut. You can cut a skirting board made of this material with a sharp construction knife, or with a metal hacksaw. You have to be careful not to force it when cutting, you can chip it if you push down on it.

Polyurethane skirting board is more expensive than the first two versions; it is denser and harder, and difficult to cut. But on the plus side, it won’t chip under pressure. It is better to cut it with a hacksaw for metal, but a sharp construction knife can work. The corner of the baseboard from this material turns out flat and neat.

This option of decoration is currently the most expensive. It is strong, resistant to moisture, elastic. But there is a big disadvantage. the reaction to temperature changes. For example, in the kitchen above the stove, it can crack and warp, and it is almost impossible to treat it, you’ll only have to replace it. But this is not a panacea, it will crack again.

Wooden skirting is a natural solid and quite heavy material, which can not be attached to the glue. Cut it with a hacksaw with a fine blade, better for metal. That way the edge of the trimmed baseboard will look flatter.

It is a question of angular elements, which are widely available on the market. Buy fittings on the corners, the plinth itself can be cut to size, at an angle of 90 degrees. The corner piece is glued to the corner, and the baseboard itself is attached to it. So you can hide all the imperfections.

But it is not always possible to apply the hardware. it is much larger in size than the fillet itself, and the corners in such an interior stand out strongly, and this is not always aesthetically pleasing.

If it is not a matter of principle, then of course it is better to buy a corner element and not to bother with trimming corners.

Decided to trim the baseboards themselves, then use some tips on how to do it right.

  • Measure the degree between the walls using a protractor. 90 degrees, then trim at 45. If the other, then its size divide in half. Both elements are trimmed.
  • The plinth, which will be fixed on the left side, trim on the right side, and the right baguette on the left side respectively.
  • Cut details of the inner corner on the edges, should look like this, the upper line is shorter than the lower. External. on the contrary, the lower line is shorter.
  • If the foam plinth in the corners can be adjusted, then with the wooden parts it will not pass and they will have to be very precise, until the full adjacency.

Carpenters’ tool, which allows you to cut blanks at different angles. the jigsaw. It is a tray in which there are slots made at a certain angle. The material from which it is made can be different, for example:

A simple design has two types of angles 45-90 degrees, a complex configuration of 90-60-45 degrees. The second type of tool is considered a professional.

Consider how to trim a ceiling plinth with a wire cutter:

One slat is ready, now you need to cut the opposite slat:

Checking the junction. consists of the fact that you need to put the cut strips to each other at the corners. For accuracy, it is better to start trimming from the front side of the baseboard. If we’re talking about wood, then the angle will have to adjust with a file.

It is worth noting that the plane is useful to you only if all the angles in your apartment is equal to 90 degrees. When the corners are not straight, you will have to use other trimming methods.

As you can see, it is not at all difficult to cut a ceiling plinth correctly with a wire cutter.

The marking on the ceiling will also help you to cut the slat to within a millimeter. It’s not easy to do, because you have to hold the skirting board by weight when trimming. But, this is the most accurate way to adjust the angle on the ceiling plinth.

Putting the baseboard to the ceiling, you can see all the irregularities on the wall. The angle deviation is also visible and must be taken into account when trimming.

In order to make the trim correctly you need to:

Once the marking is made, you can properly trim the baseboard, and try it on. It is worth noting that this method involves trimming from the inside of the workpiece.

For the trimming of the baseboard, you can make a template of a stool yourself. It is made of cardboard, paper, or wood. The principle is as follows:

A very handy device, as it not only allows you to cut 90-degree corners, but also above. But before you do it, check the corners on the ceiling, maybe they are uneven, and then the preparation of the imitation skirting board will have to correct. Because it is not possible to cut the skirting board evenly.

Cut the corner according to the drawn template can be the same as when using a real jigsaw. Only in this situation, the bar will be pressed against the drawn, parallel lines.

There is a rule to trim the ceiling plinth:

  • To mark the inner corner, measurements are taken from the corner.
  • For the outer corner, you need to know that the ceiling plinth will protrude into the room by a length equal to the width of the workpiece.

Do not glue the skirting board until both planks have been prepared and tried on. As soon as the strips in the corner fit together perfectly, you can spread glue and fasten them.

If there are flaws in polyurethane or wood baseboards, they are treated with a fine file. With plastic skirting boards, you can do with a sharp office or construction knife.

No need to despair, if after fitting in the corners there is a gap, it can be masked with white putty. To do this, even before fixing the second skirting board, which will join in the corner, putty is applied to the joint.

After the corner is fixed and pressed, it is necessary to remove the excess mixture and wipe the corner with a damp napkin. If necessary, you can paint the joints with water-based ceiling paint.

With any neat work, there are flaws, and the installation of the ceiling skirting is no exception, especially if you are doing it for the first time, and have no idea how to neatly cut the ceiling skirting. You can remove flaws and defects this way:

  • Apply glue to the joints, which are used to fasten the skirting boards.
  • As soon as the glue dries on the joints. you just need to wipe it off with a clean rag.
  • As for the gaps in the ceiling area, they are plugged with putty and painted with paint. Do it gently with a rubber spatula.
  • If there is a white sealant at home, you can use it to seal gaps, then paint the joints will not have.
See also  How to wind a fishing line for a trim on a gas station.

As we see, the exercise of trimming the corners of the ceiling plinth is not difficult, and anyone can master it. Do not immediately begin with trimming corners on the whole slat, train on small items. And as soon as you begin to succeed, move on to a solid baseboard. We hope you learned from this article how to cut ceiling skirting boards in the corners correctly.

Ceiling baseboard is a construction material that, in addition to its decorative function, also serves a number of purposes. It is used to separate the ceiling from the wall. Under the baseboard usually hide the joints between the materials that have been used to finish surfaces. Not every room is acceptable to install moldings, but most often the room without it will look as if it is unfinished. Fixing the skirting board is not too difficult. Most often special glue is used for this purpose. But the question of how to evenly cut the ceiling plinth in many causes difficulties. Below we will consider different ways to trim baseboards. The following tips will help you in different situations to make the correct trimming of the ceiling plinth.

Before proceeding directly to the tips, you need to find out what tools can cut the baseboard. The answer will depend on the material from which the latter are made. So, the skirting boards can be made of PVC, foam, wood or polyurethane. Let’s consider each of them in more detail.

The most budgetary option of all are considered skirting boards made of PVC. They very often have bends and dents when cutting. It is impossible to fix it. Another significant disadvantage of PVC baseboards is that they attract dust. It is best to use a sharp construction knife to cut them.

Another fairly cheap option are skirting boards made of expanded polystyrene. It is worth mentioning that when cutting them, they can crumble, so it is best to use a sharp knife for this purpose. To avoid damaging the skirting board, you should not press too hard on the material.

The most expensive variant to date are polyurethane skirting boards. In contrast to the above, such moldings differ from others in strength, as well as resistance to moisture. It is easy enough to cut them with a construction knife. They will not crumble in the course of the work. Perhaps the biggest disadvantage of polyurethane baseboards is their dependence on temperature differences. This can lead to their deformation.

As for the skirting boards made of wood, they are quite dense and at the same time heavy, so to cut them, you need to use a hacksaw or metal blade.

How to cut a skirting board at 45 degrees

As written earlier, the procedure for fixing the baguettes is simple enough, but only if it is cut correctly. This can be done with a pliers tool. However, if you do not have this device, you can also do without it. To cut the skirting boards correctly, you should familiarize yourself with special techniques.

In most rooms, it is the corner of 90 degrees that is finished with skirting boards. To do this, cut the skirting board into two equal parts, i.e. 45 degrees each. The following tips will help you do this.

First of all, you should make a mark on the wall. First, apply the product in the place where it should be fixed. Along the edge of the skirting board you need to draw a line on the surface. Use it to determine the level of attachment. This must be done on the opposite side.As a result, the scythe lines will intersect at a point that will be the mark of the cut. It must be transferred to the baguette.Then again, put the bar to the ceiling and draw a scythe line between the edges of the eaves. This makes it possible to highlight the fishing line on which to make the cut.

The next step is to put the baseboard to the corner and trim it. To cut the baguette, you can use a construction knife. The choice of tool will depend on what material the baguette itself is made of.

How to cut the outer corner of the ceiling plinth

In order not to make mistakes, you should first make a mark inside corner and only then begin to cut the outer corner. If this is not done, the skirting board may end up being too short.

Apply the plank to the ceiling in order to mark its dimensions.

Next, the bar should be pressed against the wall and, holding it with your left hand, set the hacksaw at an angle of 45 degrees, at the moment when the handle is close to your right hand. Trim the workpiece and match the corner.

To trim the baseboard, you can use the jig saw only if the angle between the walls is equal to 90 degrees. If this is not the case, it is better to use another method of trimming the baguette.

How to cut the ceiling baseboard at an angle

There is another original method that makes it possible to perform trimming the baseboard correctly. The essence of it is that you will need to draw the jig.

First of all, you need to draw two scythe lines on the paper. It is important that they are parallel in relation to each other. Next, you will need to mark the corners, keeping them to a degree. You can use a protractor for this purpose. Trimming the baseboard should be done the same way you would if you were using a real wood chisel. The product must be placed parallel to one of the lines and then cut the corner.

trim, skirting, board

How to evenly cut the corner of the ceiling plinth When we evaluate a new repair, we involuntarily direct our eyes,

How to cut a skirting board properly This is how the corners of a ceiling plinth look like this perfect

How to evenly cut the corner of the ceiling plinth When we estimate a new repair, we involuntarily divert our gaze,

How to properly putty walls Properly putty walls. the key to any quality repair Puttying process

How to mask the joints

With any neat job, there are flaws, and installing a ceiling plinth is no exception, especially if you are doing it for the first time, and have no idea how to accurately cut the ceiling plinths. Mistakes and defects can be removed as follows:

  • Apply glue to the joints, with which the baseboards are attached.
  • Once the glue dries on the joints. it is enough to wipe it off with a clean rag.
  • As for the gaps in the ceiling area, they are plugged with putty and painted over with paint. This should be done carefully with a rubber spatula.
  • If there is a white sealant at home, you can use it to seal the gaps, then paint the joints will not have.

How to cut the corner of the ceiling skirting means marking on the ceiling

The marking of the skirting board on the ceiling not counting that allows you to cut a corner evenly and accurately. The only disadvantage of this method is that it is difficult and uncomfortable to hold the baseboard by weight while cutting. Otherwise mark the angle for cutting so may not be considered more accurate than other ways. Applying the skirting board to the place of installation, all the imperfections of the walls and differences in the size of the corner are taken into account.

Determining the corner of the ceiling plinth:

First the two workpieces must be cut at a ninety degree angle.

After that, first attach one slat, pointing its end perpendicular to the wall. We draw a line on the ceiling, outlining the contour of the skirting boards.

We remove this slat and attach a counter slat, not counting its end in the wall. Marking the line.

The crossing point of the marked lines will be the point to cut the skirting boards. Once again we put each slat alternately and mark the cut point on them. Lead the fishing line from this point to the other edge of the skirting board.

We cut the skirting boards along the planned lines, dock them and attach them to the place of installation. Please note, that it is more ergonomic to cut inner corners with a method.

The cutting is different, depending on the material used for the skirting boards. This is due to the different density of different polymers. Consider the most popular materials and the peculiarities of their cutting.

Styrofoam

Plastic foam is a foamed polymer material. In it, you can clearly see the small bubbles-crumbles that make it up. They can be separated quite easily. This must be taken into account when slicing. The tool which will be used during it, should be very sharp. Otherwise the skirting board will crumble, leading to its deterioration.

This applies not only to cutting corner joints, but also to even cuts. Even in this case, it’s possible to shred Styrofoam.

Styrofoam

Styrofoam is a material that is very similar to Styrofoam. It is made of expanded polystyrene or styrene. It is also made up of many bubbles. However, they are much tighter to each other.

In general, the requirements for cutting are exactly the same as in the case of Styrofoam. True, the tool can be a little less sharp. But it is not worth taking not sharpened at all. in this case, the styrofoam will also crumble.

Extruded polystyrene foam

Extruded polystyrene foam is made from the same materials as conventional. However, in this case a different technology is used.

In the manufacture of conventional foamed polystyrene, water vapor is passed through the mass of microgranules.

Extruded polystyrene foam is produced using the extrusion method. The granules are mixed under high temperature and pressure, and then a special blowing agent is added. As a result, the cell size of extruded polystyrene foam is much smaller than that of conventional polystyrene, it does not exceed 0,2 mm. Thanks to this feature, the material has greater strength and is much less crumbly.

See also  How to saw a board into boards with a manual circular saw

It is easier to cut extruded polystyrene skirting board than a standard product. The requirements for tool sharpness are not so high. And the work does not require excessive accuracy, as the material does not crumble so much.

Polyurethane

Polyurethane is another polymer material. It is dense enough and does not crumble at all. This makes it easy to cut. The tool should be sharpened, but excessive sharpness is not required. No need to monitor the pressure. polyurethane not bad takes any degree of it and does not deform and crumble (if the correct direction of force).

How to cut skirting board or baseboard corners. No power tools required!

Wood

Wooden baseboards are cut with a hand or electric jigsaw. The place of the cut should be further processed with a file or sandpaper.

The main advantage of wood products is that they forgive small mistakes. After all, if necessary, the unevenness can be smoothed out with a rasp. And the main drawback is that they do not forgive serious mistakes. If you spoil the polymeric baseboards, you can buy new ones in any quantity. the price allows it. Damage to the wooden will incur additional costs. wood products are much more expensive than plastic.

Finishing finishing work in the house, many homeowners are faced with the problem of cutting the ceiling skirting boards, especially their corners. After all, it depends on them the attractiveness of the interior. Without these decorative elements, rooms look unfinished. It is not difficult to guess how to cut a ceiling plinth with an angle, a metal ruler or a flat plank, because it is only necessary to maintain a right angle.

But in the finishing work is required to cut the skirting boards and at other angles, such as 40 degrees. Therefore, the installation of these plastic elements is fraught with certain difficulties. To get the appropriate angle, you need to be extremely careful. One of the problems is to cut the ceiling skirting boards in the corners with further joining.

The following materials are used in the production of baseboards:

  • Wood. Wood is considered the most difficult material to work with. Wooden skirting boards are sawn with a joiner’s hacksaw.
  • Extruded polystyrene. High Density Finishing Material. Does not absorb moisture. In combustion does not emit toxic substances. It is rather difficult to process, but easy to cut. Only needs a carpenter’s knife.
  • Foam. It is fragile, the cheapest and easiest material to work with. Its brittleness is not a disadvantage, because the skirting boards are located under the ceiling and they are not afraid of mechanical effects. It is easy to cut skirting boards from foam plastic.
  • Polyurethane. Characterized by plasticity and flexibility. Due to these properties, it is used on uneven surfaces. Water repellent and resistant to temperature changes.
  • Polychlorvinyl. The material is difficult to fit because of its high rigidity. Manufacturers offer it in different finishes: imitation stone, metal, wood and uniform coloring. Becomes brittle in cold.

Decorative elements made of aluminum look no less attractive under the ceiling. True, to process and cut the metal is much more difficult than the materials from the proposed list. Increased demand for aluminum skirting boards is due to the fact that they are cable channels, which is convenient to hide wiring and cables. Important is the aesthetics, non-responsiveness to aggressive environments and detergents.

Cutting aluminium ceiling skirting boards with a metal circular saw. In order not to break the blade, the reciprocating motion must be smooth and even.

Regardless of the material of manufacture, ceiling plinths can be considered the best solution for creating a unique interior. They are mounted in the most difficult area, which is the joint between the wall and the ceiling. Someone who knows how to properly cut the corner on the ceiling plinth, quickly make the interior of the room completed, which will give it more appeal. With the help of these elements it is possible to partially hide small defects.

The tool for cutting choose depending on the material and the necessary corners. In rooms of standard shapes with perfectly flat walls and ceilings, to cut the corners of the ceiling plinth use a plier. Wood is sawn with an ordinary carpenter’s saw, and for other materials a jigsaw should be purchased. You can also use a metal saw. To adjust the corners manually, you will need additional tools: ruler, angle, protractor, pencil.

Angle cutting techniques

At what angle to cut the ceiling plinth? In the case we are trying to decorate the ceiling plinthing right angle (in all apartment buildings and most private homes other angles do not meet) 45 degrees.

Right angle, divided into two equal sectors.

How to cut a ceiling plinth at an angle?

Cutting ceiling plinth with the jigsaw

The most common way to cut an angle is with a simple carpentry tool, the plier. It is a construction of an aluminum, plastic or wooden tray with grooves that guide the hacksaw blade at certain angles to the axis of this tray.

How to cut corners with this tool?

  • Fix the baseboard in the tray in the same position as it will be installed on the ceiling. Align it on the side that will be pressed to the ceiling.
  • With your free hand we cut along the guide groove. For wood, as mentioned before, we use a hacksaw. Both Styrofoam and polystyrene can be cut with a metal saw. You can also cut Styrofoam or polystyrene skirting boards with a knife, but the knife must be very sharp. Otherwise the material will chip away under the blade.
  • A wooden skirting board may need to be fitted with a file before fitting it to the wall. To fit softer skirting boards we again use a sharp knife.

How to cut a ceiling plinth in the corners? We’ll need a simple power plier

How to cut a skirting board in corners? We’ll need a simple pliers tool.

Corner cutting itself is very simple; avoid, however, excessive force. Styrofoam is easy to crumble. And the wooden baseboard with too much enthusiasm is easy to split.

Cutting without a chisel

How to cut corners if you do not have a plier at your disposal?

Method 1

One of the easiest solutions to make a counterpart of the chisel yourself.

  • Make a simple tray of three planks.
  • Cut it at an angle of 45 degrees. You can mark an angle with a protractor or a student’s angle piece.

The chair is very easy to make yourself. If you have a lot of corners to adjust this work will pay for itself

Method 2

You can make do with a tray without a slot. Make a template corner of paper or cardboard (this is especially important if the angle is not exactly 90 degrees) and draw a fishing line on it, which you will navigate.

Pinch the boards together at right angles (in this case, it’s easy to get by with two, not three).

  • Insert the ceiling plinth for conventional or stretch ceilings into the improvised tray in exactly the position in which it will be attached to the ceiling.
  • Place the tray on the edge of the template.
  • Cut the skirting board, referring to the line drawn on the template. Hold the knife or hacksaw strictly vertically.

Method 3

We also need an improvised tray in this case, but it can be absolutely any kind. You can simply use a table pushed against the wall or the corner between the wall and the floor.

How to cut corners with such a strange tool?

  • Mark the future corners on the ceiling, the wall and the baseboard itself. These are the ends of the imaginary mowing line, which will cut both planks of the baseboard.
  • Install the baseboard in the tray exactly as it will be attached to the ceiling in the bedroom or other rooms, and cut it, guided by the applied risks. Again, keep the knife or the hacksaw blade strictly vertical.

How to cut a ceiling plinth in the corners with a minimum set of tools? Easy. All you need is a pencil, a knife, and an eyeball

How to trim a baseboard in the corners with a minimum set of tools? Easily. All you need is a pencil, a knife, and an eyeball.

How to cut the corners of the ceiling plinth

The most difficult thing when installing ceiling and floor plinths. it is the design of the corner. To join strips in such places must be very carefully, otherwise the appearance of the decor will be hopelessly spoiled. Of course, you can use quite aesthetic special angular elements.

However, naturally docked slats usually look more harmonious. And spend money on additional parts in this case will not have. Therefore, further in the article we will consider how to cut the corner of the ceiling plinth correctly and what to process the seam.

The necessary tools and materials

First you need to prepare the panels themselves. Depending on the material, you will need different tools to properly cut the baseboard.

PVC tacks are not as brittle, but they are still prone to dents. They can be cut with a construction knife or hacksaw. Styrofoam is more brittle than PVC. It can just fall apart when you cut it. Well-sharpened tools should be used. A sharp knife or a hacksaw will work. Do not apply excessive pressure on the material when working. Polyurethane panels are easy to cut and do not crumble. They can be cut with a knife. It is more convenient to cut wooden panels with an electric saw or a hacksaw. The serrations must be very fine. What else you may need when working:

  • Chisel;
  • Knife, hacksaw or electric saw for cutting panels;
  • Paper and pencil for drawing and marking;
  • A ruler and a square.

The chisel is a special tool for cutting panels at a certain angle. Inexpensive, so it makes sense to buy it for a better job. You can make it yourself or draw a template on paper in its likeness.

| Denial of responsibility | Contacts |RSS