How to unscrew a small screw if you do not have a screwdriver

How to unscrew the different types?

The main difference between the different types of screw fasteners is in the types of their slits and the shape of their heads. Rules for unscrewing also differ, because in each case to act in accordance with the peculiarities of metalware:

  • Straight. Both large and very small can easily be unscrewed with an ordinary flat-headed screwdriver. The basic rule of work with such hardware is a tight fit of the tool tip. The slightest gap many times increases the chances of breaking the slot.
  • Cruciate, or Phillips. The distinctive feature is the extrusion of the tool when screwing. This increases the probability of coming loose. Cruciform variants are the champions of unscrewing problems. When working with them, it is better to observe the rule of unscrewing.
  • Pozidriv. Phillips with notches and parallel sides. No push out problem with this variant and you can apply more force on the final screwing of the fastener. Pozidriv differs from Phillips only in the presence of serrations. But different bits are used for them, as well as screwdrivers, otherwise disruption of the slot will be inevitable.
  • Hexagon. Internal spline in the form of a hexagonal slot in the screw head. In order to tighten it correctly, it is important to choose the right wrench or screwdriver. the tool must fit tightly, without gaps. If there is air in the cavity, the tip of the tool will turn, grinding out the slits.
  • Sprocket, or Torx. appeared as an improved alternative to the hexagon. Designed to withstand high tightening torques, centred. With the right bit, it would be quite difficult to break it.
  • Three-beam. A variant which is considered anti-vandal because it is used so infrequently. Comes in different shapes: Y-type, Ti-wing. In the first case, the slot looks like the letter with the same name, and in the second one, like a turbine blade.
  • TORX Plus anti-vandal. Its slot is a five pointed star with a center pin. Vandalism lies in the fact that only a special bit is used for installation, it is not included in standard tool kits. No other tools are required to unscrew the screw.
  • Vandal resistant triangular slot (TA). Looks like a recess in the screw head, can be turned not only with the special tool but also with a hexagon or small-diameter slotted screwdriver. Probability of tripping is low and the bit is easy to make yourself.
  • One way. Screws with only straight strokes. In an attempt to unscrew, the screwdriver or bit is simply thrown out of the slot. Cannot be unscrewed using conventional methods.
  • With outer splines. To work with them use a special tool with a recess, corresponding in shape and size of the fixing head. Available in square, pentagonal, hexagonal, Torx, 12-point or twelve-point. Most of them are suitable for a ring wrench, head licking often occurs with excessive force during work.

These are the main types of screw fasteners with which problems occur when unscrewing. On how to solve them, it’s worth breaking down in more detail.

Useful tips

When performing the work it is worthwhile to use a few tips:

  • Before resorting to drastic measures, it is worth examining the back of the workpiece in which the screw is screwed. Perhaps the edge of the fastener is peeking out from the underside. In that case you can grasp it with the pliers and try to unscrew it from the inside.
  • When getting started, make sure that the fastener is rotated in the right direction. Some screws contain reverse threads. In such situations, to solve the problem you need to make rotations in a clockwise direction.
  • If after the screw in the workpiece left a gaping hole, you can solve the problem by inserting a larger self-tapping screw here. As an alternative, it is worth using a bolted connection with a nut.
  • When removing a screw by one of the above methods, all kinds of nicks and metallic burrs are likely to form. To avoid getting hurt while working, you just need to wear thick gloves on your hands and goggles to protect your eyes.

How to get to hard places with a screwdriver. Angle wrench, bit holder extension and flexible shaft. And of course disassembly.

Let’s look at how you can get to hard-to-reach places with a screwdriver or electric screwdriver. Sometimes the screws nuts and bolts are in places that are difficult to reach. There are screwdrivers with a swivel head, there are ratchets and other devices to solve such problems. This problem is not common, but it must be solved somehow. So I bought something simpler and cheaper. So, the first is the flexible shaft. Plastic flex casing and rope inside, at the end and beginning of the hex 6.35 for bits. What kind of force it can not do, but something easy to unscrew it can well. For example the screws fixing the trim panel in the car door are not located conveniently, you can not reach them with screwdriver and bit holder. A flexible shaft is fine for such a task. But it might not break a screw in plastic. You can use an angle screwdriver to break a screw. Or the L-jaw wrench from this review. With an angle wrench, you can basically rip off and unscrew the screws on the trim. Side play is smaller than with the flexible shaft, but the angle of rotation can be any angle up to 180 degrees, and it is fixed with the angle wrench. I wear them both, they complement each other. You can use the angled wrench to tighten a screwdriver 4 for example.2 with press washer in thin sheet metal. Large tasks are difficult for it. It has a little play after such work, but it is still working.

See also  Is it possible to cut metal. How to protect paint on ceramic tiles for many years.

How to remove small stripped screw from electronics

The only thing is, if I were to buy it now, I would take a longer version with a holder. tail. It is difficult to hold on such a small gearbox and put pressure on it when screwing screws.

Another thing that helps me with screws and screws is the bit locking extension cord. I got the short one, but there’s different lengths. In the angle drill and the flexible shaft the bits are held in place with a magnet, which is kind of nice. But sometimes a bit gets stuck in a self-drilling screw and when you pull the electric screwdriver towards you, the bit stays in the grooves of the screw. And then it often falls down, when you work at height it causes some problems, especially when you’re hanging at fifteen floors and the bit falls down somewhere This extension cord tightly holds the bit, its black “skirt” is pulled back and the bit is inserted.

The bit is secured with a stopper that retracts when the skirt is pressed. There are special grooves or slots in the bits for this very fixation. That means that if the bit is inserted in such a holder, you can be sure it will stay there and not fall out by getting stuck in the screw. And another advantage of this type of holder is that it allows you to hold on to the “skirt” while you twist the screw. If you have a long screw then when you drill the hole it tends to fall sideways. And with this screw you can twist with an electric electric screwdriver and hold the axle by the holder, the “skirt” twists freely. This prevents the screw from falling off to the side.

Let’s see what’s inside these adapters. I couldn’t disassemble the straight shaft extension. Flexible shaft. just cut off the outer plastic with a office knife. There’s a spring and a rope inside. The rope is pressed into the holders at the edges. Typical breakdown. when too much force is applied, the cable pops out of the retainer. I don’t think the repair is worth it at this price. It’s probably possible, though.

Angle wrench. there are two bearings pressed in on both sides. The retaining ring is visible. I couldn’t get it off, no matter how hard I tried. The most I could do was to remove the side bearing washer and look at the balls and the white plastic cage. Looks like a single row bearing.

Generally a tool for the DIYer or occasional use, but when you have to use it you think “What would I do without it”. Sometimes it speeds up the work considerably. For frequent and professional use there are other tools with the same functionality but better quality, but a completely different price.

Putting kebabs on a skewer, cut yourself and blood from the meat of the animal probably got into the wound. Is it dangerous and is it possible to get infected by it??

Monitor how you feel and the condition of the wound for the first time. In case of any abnormality consult a doctor.

I do not write about the treatment of the wound.к. that’s obvious.

  • The place where you bought the meat (and its reputation). Meat products are usually inspected. It is very doubtful that a place with a good reputation would sell meat from sick animals.
  • Time and method of storing meat before cooking. So, for example, storage in the freezer, or marinade in an acidic environment (vinegar, citric acid), or in alcohol (beer, wine), should theoretically rid the meat of some potentially harmful microorganisms. If the meat was kept at room temperature outside of its sealed package, the number of potentially harmful microorganisms may have increased accordingly.

How to undo a screw that has had its flats cut off for a screwdriver?

If the flat top is above the surface you can try to make a cut with a file or a metal saw for a flat screwdriver, if this is not possible, you can try using a bit or flat screwdriver to knock out a groove on the flat top for a flat screwdriver. If the edges are not too badly torn off, put between the screwdriver and the flat bar an auxiliary material. a piece of abrasive sponge or abrasive paper, rolled up scotch tape, a thin strip of rubber. You can use additional materials weld the head of another screw to the torn off flathead (with standard or cold welding, liquid nails, superglue), and then unscrew it with a screwdriver, wrench or pliers

How to unscrew a torn off hexagon bolt

To unscrew the protruding bolt under the Allen key or “star”, you can use the following methods:

  • Use a metal saw or an angle grinder to make a clean, straight vertical cut across the top of the screw head. After these steps, it can be unscrewed using a normal flat-blade screwdriver.
  • With a torx star: it must be hammered into the recess for the hexagonal key in the cap of the hardware. The size of the sprocket must be such that its slits do not go through the hole. Then the hardware is unscrewed with a sharp jerk. The use of a torx with a hole in the center is not recommended because the sprocket can be broken off.
  • Before unscrewing a hexagon with a torn edge, a hole is drilled in the center of the hexagon with a drill bit and extractors. The extractor is then driven into it, then pulled out with pliers along with the hex screw.
  • Using a drill with reverse rotation, a thin hole is drilled, then a left-handed socket is inserted and the fastener is unscrewed. In doing so, the drill should rotate slowly and the pressure should be strong.
unscrew, small, screw, screwdriver

Ways to unscrew bolts, screws, and screws with flared faces

If you are unable to unscrew the fasteners with edges that have slipped off, you can use one of several tried and tested methods.

See also  How to choose a wood grinder

Gas Wrench

This method is used when unscrewing bolts, because the head of the bolt is sticking out and can be caught. To do this:

  • Clean head of bolt.
  • Lubricate the joint with kerosene or diesel fuel, WD-40 type liquid helps a lot, and leave it for 15-20 minutes.
  • Bolt unscrewing. This is done with a gas wrench. It makes a big effort and you can catch even a round head well.

The disadvantage of this method is that it is not always possible to get close to the desired bolt with a gas wrench.

Re-cutting

If the bolt is large, you can use an angle grinder to cut new faces on it. It is enough to make only 4 of them and use a smaller wrench to unscrew the bolt. It is possible to cut a new edge on a bolt with a file, but this is harder and longer. A cut can be made in the head of the screw or screw with a metal saw or angle grinder.

Hammer and chisel or impact screwdriver

This option is more suitable for flared nuts or fairly large screws. Place the chisel against the head of the fastener and gradually turn the screw or nut by hitting it with a hammer. Small screws or screws can be unscrewed with an impact screwdriver and hammer. After loosening the fastener, the work can be done with a normal screwdriver.

Tourniquet or a piece of rubber

In this case use a small piece of medical tape or a piece of dense rubber. The material of your choice is placed on top of the head of the screw or bolt and then pressed down with a screwdriver, gradually turning it. The presence of rubber will help increase friction and solve the problem.

Extractor

The extractor is a special tool that is used to unscrew screws, bolts or screws with flared or broken heads.

  • The thin drill bit is used to make a small hole in the head. In some cases the extractor can simply be driven into the stripped slot in the screw.
  • Select the extractor of the required diameter. Hammer or screw it into the prepared hole. It depends on whether a regular or screwdriver tool is used.
  • Screw out the bolt.

Regular or left-hand drill bit

Left-handed drills are commercially available with counterclockwise rotation. They improve tool centering and reduce the load on the drill bit, resulting in higher productivity and accuracy of drilling. Inserted in a drill, the tool can be used to remove a screw or screw with a slipped head. If you do not have a left hand drill bit, you can try to drill out a stuck fastener with an ordinary one. In this case you should take a drill bit with a diameter smaller than the diameter of the bolt or screw. Be careful not to have to cut the thread for the new fastener later.

To the head of the problem screw or screw using epoxy glue or glue called “cold welding” fix a nut of the appropriate diameter. After the glue has firmly fixed it, use a wrench to turn the nut and unscrew the screw or screw together with it.

Welding

If there is a welding machine nearby, you can fix a new nut on the head of a bolt or screw by welding it on. It can then be immediately unscrewed.

Solder and soldering iron

If you need to unscrew a small screw or screw, use a soldering iron and solder:

  • Drop the heated solder on the head of the fastener with bevelled edges.
  • Before the tin hardens, a screwdriver is inserted and waits a few minutes.

What you can unscrew the screws on the iPhone 5

The iPhone is considered quite complicated, but compared to other devices, it is easy to disassemble. This has a good effect on the serviceability of the phone. After all, even an unskilled person can make any manipulations with your gadget. True, this will require a set of special tools. But what to do if you do not have them at hand??

You can open the guts of the iPhone by unscrewing two bolts located on the lower part of the device. With a special screwdriver this action will take a maximum of a minute of your time. But, if you are smart and spend a little more time, you can do everything without tools.Although the bolts have tiny threads, they are placed on the surface. So you can use a knife with a thin and sharp tip for unscrewing. Also use other sharp objects such as needles, scissors and awl. Some go further and use feminine jewelry. Particularly ingenious make very strange things. with the help of duct tape and glue make the tip of the needle something like a screwdriver, but this can afford not everyone.

However, nothing will be better than a knife, which is proved by personal experience.

Cell phones are firmly embedded in the daily lives of almost everyone. As well as any other technique, it is peculiar to these electronic gadgets to break and malfunction. A large number of models and brands cause an unlimited number of spare parts and repair tools. The main tool in repairing the phone is a screwdriver. After all, even in order to simply diagnose a malfunction, you must first disassemble the body model.

What unscrew the bolt star

As an option. If the flat is not countersunk, you can cut a slit for a flat screwdriver with a hacksaw blade and try to unscrew it that way. Before you do this, it is worth warming up the bolt with a technical hair dryer or a soldering iron of sufficient power, it should facilitate the work. If the flat is big enough, you can also try to twist the bolt with the pliers, clamping it harder.

If the head is flat or countersunk, it will be much harder.

unscrew, small, screw, screwdriver

For this purpose I took a suitable flat bit from a screwdriver, so that it fits very tightly into the hexagon, gently hammered it in and then tried to turn it with a pair of pliers.

And even better to use special extractors for unscrewing bolts, they are sold as all kinds of kits or even individually.

A bolt is a fastener with an external thread.

It may consist of two elements, the threaded rod itself with the head and the nut, and can be screwed into a hole with an internal thread, that is, the nut is not on the end.

See also  How to unscrew a slugged screwdriver bolt

The so-called “sprocket” can be male,

If it is external, you will need a hammer to tap the bolt, but without fanaticism.

VD-40 penetrating fluid, it will facilitate the unscrewing of the bolt.

If it is not a nut at the end of the bolt, use the same pliers to hold the head, and unscrew the nut with open-end wrenches of the required size.

If the “star” inside, you can make a straight bar for a flat screwdriver, you’ll need a hacksaw for metal, or an angle grinder with a cutting disk, or a sharp chisel, the same hammer, VD-40, screwdriver.

In the most extreme case (nothing helps), the bolt can be drilled out, you need a drill and drill bits for metal.

One more variant of loosening the bolt with inner sprocket, which is actually what I used.

Armed with a dremel, put a small abrasive disk on it. On the round head of the bolt with the internal sprocket, made two faces for a ten-millimeter open-end wrench. Just sawed off two halves on opposite sides. Unscrewed it with a regular wrench. This can also be done with a normal socket wrench and even with an iron file. In the picture below, the red areas show some of the metal being removed from the head of the bolt.

There is another way to unscrew bolts with hexagonal socket or sprocket, but with stripped edges. This paste increases the adhesion of the mating parts. Quite simple to use, does not take a long curing, adhesion is very good tool (a Phillips screwdriver, Allen screwdriver or a sprocket head “stick” into the slot perfectly). If used according to the instructions, there is no paste left on the tool.

Often there is such a problem, when a sprocket bolt gets torn off and a person doesn’t have the slightest idea how to unscrew it. And there may be a situation where you can’t unscrew a bolt with a wrench.

unscrew, small, screw, screwdriver

How to unscrew a small screw without a screwdriver

I had a problem unscrewing the bolts and didn’t want to drill them out. Two days of effort, but it worked. And these bolts were on the carburetors, so even more care was needed! Maybe someone can benefit from my experience I decided to disassemble the carburetors on a suzuki RF400, because I got it sick, here’s the post about it: RF-ca is dying took them off as expected, brought them home, so as not to sow anything in the garage, sat down to disassemble A minute later realized that it would not be very easy(( The thing is that the float chamber trays are screwed to the carb and at the first attempt to unscrew them broke a cross on the bolt (( Turned one bolt. broke it, began trying to rest. I feel the cross What to do. And there are eight bolts, two on each carburetor and not one unscrewed. I decided to try to clamp them with tonknose What to do next, I did not know, so as they say “Ok, Google!”The result: unscrewed 2 bolts and there are 8 of them Some solutions found there were interesting but others didn’t fit (heat with burner is dangerous. plastic floats inside. can melt, I guess). But I didn’t find any particular way to my problem, so I unscrewed everything in a few tries)

Tried it : made a notch in one of the bolts with the flat screwdriver!

Tried : I decided to pour WD-40, wait, try with small side cutters to catch the bolts from the outside and tonknockers Result: unscrewed 2 bolts, and there are 8 in total.

Tried : Went to the store, bought tougher side cutters. Before leaving, all a good watered WD-40, Result: unscrewed three more bolts, 3 remained, they did not want to succumb Tried: read somewhere that you can tap on the head of a hammer, it can help nuts come back Result: did not help

Tried : found a soldering iron at home. decided to warm it gently from the edge Result: it got so hot that it does not even burn your hand, in short a complete failure

Tried it : I soaked some cloths in acetic acid and put them on the flats overnight Result : I unscrewed one more bolt and broke the new side cutters

And it was already the second day of disassembly of carburetors, according to my plans I should have already assembled them by this time!) But.

Tried : Again to the store Bought new side cutters, even more powerful) Tool “Liquid Wrench” And as a last resort extractors and drills Decided to try watering with the liquid wrench and once again try to unscrew with side cutters. If it did not work, I wanted to drill a small hole in the flat and screw an extractor into it. The extractors have reverse threads, t.е. You screw them into the bolt and the bolt unscrews, the harder the extractor is tightened, the harder the bolt unscrews. That’s about how it works. In fact, it was already a desperate measure. I really did not want to drill the bolts!

I used Liquid Wrench, went to lunch, after about an hour and a half I went back to my carburetors Barely, somehow, with an incredible effort these last two bolts were able to unscrew them with side cutters.! I clamped the side cutters with both hands as hard as I could! Result: Yay, it worked!

That’s how complicated everything is, I honestly did not expect such a mess! These bolts are really so hard stuck that I could not octricate them with all my might, and the crosses on the bolts go with incredible ease. Will have to look for wrench bolts probably better. I hope this is helpful to someone! If anyone has any other ways to write in the Комментарии и мнения владельцев! Thanks for reading, everyone! Good luck to all and good weather, because in Tver it is raining again!

| Denial of responsibility | Contacts |RSS