How to wind a fishing line for a trim on a gas station.

How to change a fishing line for a trimmer in a trimmer

Trimmer for grass is the most common unit used to cut grass and cut small shrubs. This device is distinguished by its simplicity in maintenance, simple management during operation, and even women cope with it even a small weight. It is no secret that for the high.Quality performance of herbal mowing work, the correct selection of a cutting tool is required. As the latter in trimmers, special cutting nozzles (wheels, knives) or trimmer heads with fishing line inside are used. Nozzles and a fishing line for a trimmer are a consumable tool, but if the knives can be sharpened, then when spending the fishing line you need to replace it. In this article, we will tell you in the most detail how to correctly replace the fishing line for the trimmer.

A mowing head for grass is a cylindrical case in which a coil (bobbin) is inserted with a fishing line in it (cord). This design can be installed both on gasoline and electric trimmer. The heads differ in the method of refueling and supplying the cord and there are 3 types.

  • Automatic. The cord is supplied after the user reduces engine speed. Although the automatic supply of the fishing line is convenient if large volumes of work are performed, such rods have one drawback. A large thread consumption.
  • Semi.Automatic. Using this type of head does not require complicated manipulations from the user. The principle of their operation is arranged so that the cord is automatically lengthened at a time when the device works at full speed. It is enough to slightly hit the trimmer’s head for the grass on the ground (this removes the cord lock), and the fishing line for the trimmer, due to the centrifugal force, moves out of the bobbin, after which it is cut to the desired length with a knife located on a protective casing.
  • Manual. For lengthening the cord, the device is required, after which the fishing line for the trimmer is handed out manually.

Based on the above, semi.Automatic bobbins are the most optimal option. It should also be borne in mind that the coils for a trimmer for grass are one.Built (used only to trim the grass) and two.String, which are used to mow high grass and small, with thin stems of shrubs.

How to replace a fishing line for a trimmer on a trimmer?

Replacing the fishing line for the grass with step.By.Step instructions will even allow the owner of the lawn mowed inexpensive in such matters to do a fairly difficult job.

However, before starting work to replace the fishing line on the trimmer, it is necessary to ensure the safety of work. In particular, it should be taken protection measures against careless or spontaneous inclusion of the lawn mower:

  • Exclude spontaneous start,
  • Delete the battery (if used),
  • Place the tool on a comfortable site for work.

It is convenient to perform work on replacing the fishing line for the grass when the lawn mower lies on the table, and the master, who is performed by replacing the fishing line of the trimmer for the grass, has the opportunity to approach the instrument from any side.

Remove the head of the head of the grass for the grass

At the first stage of disassembly, the head of the head of the grass is removed. On the example of the models of trimmers “Black and Decker” and others, it is usually enough to apply some pressure to squeeze the click-fixer, which are on the side of the head of the head of the head of the head of the head of the body to remove the lid to remove the lid.

Some models of lawn mowers initially include dismantling the head of a trimmer for grass, for which a playback key is used, which is included in the tool kit. The head is usually held by two or three screws, access to which is provided through the side holes of the rear decorative cover.

wind, fishing, line, trim

The head cover, where the coil with a fishing line is installed, is usually held due. It is enough for some effort to squeeze the tongue-thorough and slightly turn the lid, after which the lid is easily removed

At the time of squeezing the tongue-fixer, you need to turn slightly and raise the head of the head of the trimmer for the grass to remove the winding drum.

Step two: extracting a winding drum (coil) with a fishing line

The next step in the process is the exhaust drum with a fishing line from the inner region of the head. You need to turn the head with an open side to see a fishing line for a trimmer and a reel. On the side of the head, find two recesses (eyelets) through which the fishing line for the trimmer is bred outside.

You should release a fishing line for a trimmer from the holes by checking the drum. Then gently remove the coil from the head of the head. The winding drum of some models is installed on the spring. This moment must be taken into account by performing the operation to extract.

The procedure for extracting a coil of a trimmer for grass with a fishing line from the inner region of the head: 1. Head assembly with a coil; 2. Extracting neatly with a small axial turn; 3. Extracted details

The old fishing line for the trimmer is completely removed from the coil. To remove the old fishing line for grass, you need to remove the forest from the loops and pull the free end. This method is removed by the whole old winding. A similar process is repeated on the second section of the drum. The master is recommended to use gloves when performing work.

Making a cord cord holder

On the outer forming cup.Shaped sleeve on the back of the ruler and marker, we plan two marks on the diameters perpendicular to each other.

Piscifun Review ~ Innovative or Cheap JUNK?

Then, focusing on the first four marks, we transfer them to the middle of the side surface of the cup.Shaped sleeve strictly vertically. We clamp the cup.Shaped sleeve into a locksmith and in the marked places with the help of a core and a hammer, we set the drill points, which we do using a drill. Two anti.Icing holes should be obtained in perpendicular diameters.

We clean the metal around all four holes, alternately processing them with a manual file. Over each of the four holes on the outside, we install and weld along the nut with a rounded top.

We clamp sequentially two bolts in a vice and directly under the heads, drill through the through holes with a diameter of a little more than two millimeters.

We steal nuts on them and lay both bolts with probably nuts into the annular recess of the cup.Shaped sleeve inward symmetrically between the two holes opposite each other.

The location of the bolts should be such that the nuts on them are freely twisted and unscrewed from the head to the top of the holes drilled in them. After making sure that the bolts are laid correctly, we weld them to the sleeve on both sides.

We unwind a two.Millimeter cable and pass it at one end through any of the side holes in the cup.Shaped sleeve towards the bolt. We pass the hole in it with the rope and pull out the end of the rope out through the hole in the sleeve on the other side of the bolt, helping ourselves with nippers.

We set the required length of the elongated cord and, having measured the same size on the other side, snack the cord in the intended place with nippers. We do the same with the second “Usik”, and tighten the nuts on the bolts using an online key with an effort sufficient for reliable fixation of the “antennae” in a given position.

Typically, the ultrasound rope at large operating speeds quickly decay, lose their strength and begin to break under the influence of a huge centrifugal force. This worsens the work of a trimmer for grass, but what is even more dangerous, they can damage the legs of the operator or people nearby. Therefore, you should make a shell from the solder with a soldering iron along the entire length of the “antennae” from the cable. A soft solder, which has significant plasticity, in contact with the stems of grass and small bushes, extinguishes most of the impact strength and, thereby, protects the cable from destruction. So, a home.Made working body of a trimmer for grass is ready.

Preliminary preparation

First of all, to wind the fishing line, it is required to remove the coil (bobbin, spool) from the trimmer for the grass. Specific actions will depend on the complexity of the configuration and the type of product itself:

  • Small electric trimmers for grass with a working location of the engine and coils in the lower part, as a rule, have side keys on both sides of the bobbin. With the simultaneous press on them, the upper part of the coil, along with the internal contents for winding the fishing line, is disconnected, while the lower remains on the trimmer. It is advisable to analyze the bobbing in an even smooth place, so that the spring does not jump out and not be lost;
  • Electric and gasoline trimmers for grass with a curved rod without the ability to install a knife, as a rule, have coils with a special lamb: in such structures, you should hold the spool in a fixed position with one hand, and rotate the fixing bobbin on the bar with a barack bobber. After disconnecting the nut, the whole bobin is removed.
  • Electric and gasoline trimmers for grass with the ability to install a knife on a straight rod (for example, trimmers for STIHL grass) have a hole. For the immobility of the bar, a screwdriver or another suitable object is inserted into this hole and, with slow rotation, such a mutual arrangement is achieved when the screwdriver enters the hole and the bob is fixed. After that, the coil body is scrolled clockwise (with the left thread) and removed from the trimmer for the grass.

How to Spool ANY Fishing Reel Using a Portable Line Spooler Winder Tensioner | Ecooda Piscifun

For the second and third cases, the coil, depending on the design, are versed in various ways. In the bobbins with a lamb, lamb is twisted, in the reels with latches, latches-fixers are pressed and one part of the coil is freed from the other. If the halves of the spool are connected by thread, then it is enough to turn them with your hands in the opposite directions until they are completely developed.

Winding of a double fishing line

Usually the coil is divided along the 2 parts of the walking partition. You need to take a fishing line for a skein trimmer and wind it into one half to measure the capacity with the selected cord diameter. You need to wind so much so that the lace does not stick out. As soon as half is filled, you need to wash the fishing line for the trimmer back, remembering the used meter. The cord should be cut off with a length of exactly 2 times more than placed on the half of the coil.

Having reached the end, you need to fix the ends of the fishing line in special opposite cuts on the side of the coil. Since one of them is longer, the free tails at the output are almost the same.

Now you need to insert a coil mainly with the spring. At the same time, the ends of the fishing line stretch into the holes in the mowing head. They are pulled up to free themselves from the capture of the slots on the coil. After the lid is placed and the head is ready for use.

Winding of a double fishing line

Usually the coil is divided along the 2 parts of the walking partition. You need to take a fishing line for a skein trimmer and wind it into one half to measure the capacity with the selected cord diameter. You need to wind so much so that the lace does not stick out. As soon as half is filled, you need to wash the fishing line for the trimmer back, remembering the used meter. The cord should be cut off with a length of exactly 2 times more than placed on the half of the coil.

Having reached the end, you need to fix the ends of the fishing line in special opposite cuts on the side of the coil. Since one of them is longer, the free tails at the output are almost the same.

Now you need to insert a coil mainly with the spring. At the same time, the ends of the fishing line stretch into the holes in the mowing head. They are pulled up to free themselves from the capture of the slots on the coil. After the lid is placed and the head is ready for use.

Fuel filling method

In cheap, low.Power samples, fuel is poured into the tank at the same time. This creates inconvenience for users, since before work you have to mix oil and gasoline. In expensive mowers, 2 separate tank for gasoline and oil are installed. Replenishment of fuel occurs as you use and not interdependent.

In cheap devices, simultaneous combustion of gasoline and oil occurs. This leads to the formation of a large amount of exhaust gases, an increased noise level. In expensive models, the oil is separate from gasoline, does not burn out, which leads to the formation of a smaller amount of carbon monoxide. The second bonus of separately finding oil and gasoline is quiet work, low vibration level of the tool.

In some versions, designers install special sound.Absorbing nozzles, but you have to pay extra for them.

The choice of fishing line

In order to easily wrap a fishing line for a trimmer to a trimmer coil for grass, it is worth deciding on what tasks the garden tool will perform. The thicker the thread tucked into the head, the more difficult the tasks that it can complete. It should be noted that a universal thread is often used, the width of which does not exceed 2 mm. You, in turn, can decide on the size, using the following methods:

wind, fishing, line, trim
  • Get acquainted with the information set out in the instructions from the manufacturer;
  • Check the suitability of the fishing line for use on your own, trying to insert it into the coil hole;
  • Study the spool for information about diameters allowed for use.

Selection of fishing line for refueling a trimmer for grass can be carried out by engine type. So, for example, an overly thick thread can affect an increase in rotational resistance. Because of this, the load on the engine will increase, which will certainly affect the quality and timing of its further operation.

Avoiding negative consequences is easy. To do this, it must be borne in mind that for electric motors with a power of up to 500 W, a fishing line for a trimmer with a diameter of up to 1.2 mm is ideal. If you cannot get such a thread, you can use the cord by 1.6 mm. A thread with a diameter of 2 mm, in turn, is used for engines with a power of more than 1 kW. It is worth noting that the cord for 2 mm is often used for winding on a bent mower. If the gasoline device has a straight shaft, the thread should be used 2.5 or 3 mm. The thickest fishing lines are installed exclusively on devices, the power of which is equal or exceeds 1.3 kW.

The last, but no less important factor is the type of fishing cross section. When choosing it, it is worth focusing on the tasks set before the garden tool. There are several demanded cross.Sectional options:

  • Twisted-has a small margin of safety, which is why it suits exclusively for young grass;
  • Substitute. Is characterized by sharp edges suitable for working on overgrown weeds;
  • Round. The most common section. Such fishing lines cope well with fresh grass, but they are not suitable for shrubs and dry ones;
  • Rectangular, square and star type of cross section-due to low strength, are used to work on lawns.

The most durable and universal cord is a two.Component fishing line for a trimmer with a round cross section, inside which the core is located. It is this thread that is suitable for the majority of work. It must be remembered that the use of fishing fishing line, ordinary wire and other third.Party materials as a cord pose a danger to others.

Fishing winding

At the next stage, we wrap the fishing line for the trimmer, making sure that each end is in its groove. When wound. The ends of the fishing line must be temporarily inserted into the side grooves.

wind, fishing, line, trim

Then we insert the coil into the head, put the lid on top, straighten the ends of the fishing line so that they leave the grooves, and then fix everything on the latches.

Details about how to wrap a fishing line for a trimmer to the head of a trimmer for grass, you can watch in the author’s video. This review is prepared on the basis of video from YouTube Hotsem channel.

| Denial of responsibility | Contacts |RSS