Installation of a trimmer for grass on the boat motor. What can be done

How to make a boat motor from a garden trimmer for grass with your own hands

Many avid fishermen have repeatedly thought about how to remake an ordinary rubber boat into a motor swimming product. To do this is much easier than it seems. for this it is enough to install a boat motor from motorcycles on it. We will talk about possible methods and nuances of the engine for the engine to install it in more detail.

Methods for making a boat motor from a trimmer for grass

There are three ways to make a boat motor from a trimmer for grass. Between themselves, they differ in the parts used and the principle of independent assembly.

Method

This method stands out by its simplicity and efficiency.

For work, you will need to prepare:

  • the clamp, which is necessary for attaching the device on the boat traffic;
  • rowing screw. it can be bought ready.made in the store. The standard assembly of the node includes a drive made of stainless steel, and adapters that need to be connected to a flexible shaft of household motorcycles. Some models of the screws are delivered along with clamps, so the buyer will need to specify in advance a set of parts included in the set of delivery.

As a rule, in the set to the screw there is already a finished drawing. This makes it possible to save on finding the necessary schemes for work. It takes about 1-1.5 hours to install the boat engine.

Method

To assemble the boat ICE, the manufacturer will need to prepare a corner gearbox that can be removed from the corner grinder. Also, a rowing screw is necessary for alteration. it can be cut out of a sheet of stainless steel and bend the resulting blades at the right angle.

Despite the relatively small step of the screw received, this method of alteration makes it possible to achieve the maximum possible speed from the engine. The only negative is the need for additional engine adjustment for which you can use the pliers.

Method

This method differs from others to make some details for the boat engine with your own hands. This will require a 2-stroke gasoline ICE with a cylinder of 25 cm3. The power of the internal combustion engine from a trimmer for grass should not be less than 0.7 kW, and its weight is not more than 4.5 kg. The unit should be equipped with a bent foot. The engine from a trimmer for grass, which meets all these parameters, will make it possible to move on a boat at a speed of 5 to 8 km/h with a minimum fuel consumption. We will tell you about the principles of its manufacture in more detail below.

installation, trimmer, grass, boat, motor

The advantages and features of the alteration of the trimmer for grass in the boat motor

The use of the lawn mowing available on the farm has a number of advantages. Firstly, the owner of the boat will not overpay for an expensive motor purchased in the store. Secondly, the motor for a boat from motorcycles consumes much less fuel than specialized boat engines. Thirdly, the engine from the lawn mower has an order of magnitude smaller dimensions than the boat engine purchased in the store. There are a number of other factors forcing fishermen to use a trimmer for grass instead of a boat motor.

  • high reliability of engines of modern trimmers;
  • complete tightness inside the body;
  • the presence of all the elements necessary for the control of a home.made engine;
  • The presence of a built.in tank.

Super Fast Drill Powered Boat Motor

Thanks to all these factors, the boat motor from motorcycles is most popular among enthusiasts.

In the process of processing the engine from the lawn mower to the boat engine, it is extremely important to consider that this power unit was produced for other purposes. Trimmer engines operate at small torque, but, at fairly large speeds. In the case of a specialized boat engine, everything happens the other way around. In this regard, to remake a motor from a trimmer for grass, you will need to prepare drawings, equipment and observe a certain procedure.

Despite some difficulties in converting, it is in the trimmer that all the details necessary for the manufacture of the boat engine are a built.in starter and a gas lever, a rod with a hard shaft and a translucent fuel tank.

Homemade boat motors from a trimmer for grass. options for alteration

You can make a boat motor from a trimmer for grass in three ways. The first option is extremely simple, and does not require large financial investments. For work, you will need to buy a clamp necessary for attaching the engine to the boat transza, and the rowing screw. The latter can be sold both separately and in the form of a special kit. The set includes a special drive made of stainless steel, and several universal adapters required to connect a flexible shaft motorcycles. Often, the striper itself is also included in the set of the screw, therefore, before ordering the kit, be sure to specify what is included in it. The purchased kit can be used to install the engine from motorcycles to the boat. Work is carried out according to the instructions and takes away no more than half an hour.

The second option is more complicated in execution. For work, you will need an angular.type gearbox from a corner grinder, bearings and seals for mounting a motor, as well as a screw that can be cut from a solid steel sheet. This method makes it possible to increase the engine speed from the trimmer for grass. With practical use, such a design needs to be adjusted, for the implementation of which there will be a plot.

The third option is the easiest and consists in buying a special nozzle. Such a nozzle on a motorcycle for a boat does not require any alteration-it is enough to purchase a ready-made device and equip it with an existing trimmer for grass.

How to make a motor for a boat from a trimmer for grass. step.by.step instructions

Before making a boat engine from a lawn mower, you should carefully prepare. For work you will need:

  • household trimmer for grass, with a capacity of at least 3 liters. With.;
  • a sheet of duralumin or steel with a thickness of at least 2 mm. it will be required to make a screw;
  • welding machine;
  • fasteners;
  • clamp or other device for fixing the motor to board the boat;
  • Drill and corner grinder.

Immediately before work, you should study the scheme in detail. It should indicate the size of the elements required for the work, as well as the order and method of installation.

It will also be necessary to determine the dimensions of the rowing screw in advance. they depend on the maximum power of the drive used and on the mass of the boat in a loaded form. When choosing sizes, it should be borne from the fact that a screw with dimensions of 10 × 3 cm is capable of transporting a swimming product with passengers, with a total weight of up to 120 kg.

The procedure for the manufacture of an engine for a boat from a trimmer for grass is as follows:

  • First of all, it is necessary to remake a bent shaft. From this goal, carefully remove the factory nut, originally placed in a bobbin with a fishing line. The nut has the shape of a 2-centimeter tube with an internal thread. The standard nut can be divided into 2 full details. At the same time, it is very important not to lose details, since each company-producing trimmers will equip its equipment with original spare parts. After extracting the nut, you will need to dismantle the plastic pad located on the gas button. There are no bearings at the end of the curved washer, and instead there a bronze sleeve is installed there, which also needs to be removed. After that, you need to knock out the plastic tread of the flexible shaft. The steel pipe available in the design can be thrown away, since it is not possible to get it perfectly without special equipment. Instead of a steel pipe, use a duralumin part with the same diameter. In the latter, install the previously extracted bronze sleeve and reliably impress it on a canvas using a hammer or a kiyanka. Next, take a plastic tread, cut it in diameter and mount it motionlessly into the pipe. If the outer diameter of the duralumin tube is larger, and the part cannot crawl into the hole for mounting on a motor boat, then it will need to be gripped until the optimal size is reached. If possible, then you can make a longer shaft by applying a suitable tube for this, and mounting a suitable bar of steel instead of a regular flexible shaft;
  • At the next stage, you need to make a screw. To do this, from the duralumin sheet, it will be necessary to cut a strip, in size 10 x 3 cm or more. The edges of the cut strip must be sharpened. The screw step should be approximately 1 cm, so each of the blades should be bent upward by 10 mm to fix the rowing screw. In the manufacture of the screw, it is not necessary to use the venerable veneer, since when the screw impacts it will stop rotating;
  • Next, you will need to replace the standard plastic overlay of the motor with a conventional bicycle switch. The direction of emission of exhaust gases can be changed by redrawing the muffler towards the rowing screw;
  • At the last stage, you will need to attach the shaft to the motor from the trimmer for the grass. To do this, from ordinary plywood you need to cut 2 overlays that will be used to attach the engine to the head. It is necessary to fix the shaft with 4 screws that will clamp the part motionless. If necessary, then the shaft can be disconnected so that it is more convenient to transport the motor.

To run in a do.it.yourself boat engine from a trimmer for grass, you will need a full gasoline tank, which must be diluted with engine oil in a ratio of 40: 1. One liter of fuel mixture will allow you to swim on a boat about 10 km of path. The maximum speed of a boat with a motor from a trimmer for grass will be about 6–8 km/h. It should be remembered that the higher the transported weight, the lower the speed of the swimming agent will be.

Homemade leg from a gearbox from a corner grinder for Lifan motor with a vertical rampart of 6.5l.With.

Do.it.yourself motor motor

The easiest way is to make a motor for a boat from a trimmer for grass with a straight bar and a hard shaft. If your unit has a curved bar, then it will have to be redone.

Alteration of the curved shaft

First of all, it is necessary to get a full.time nut under the number 2 shown in the diagram below. It looks like a cylinder 2 cm high with a thread chopped inside it.

Further, the alteration of the rod is as follows.

  • Remove the metal flexible shaft (9) and Deadwell Val (8) from the bar, promoting the nut (4).
  • Since the end of the bent bar does not contain any bearings, and their role is played by a bronze sleeve (6), it is required to cut it out.
  • After the bronze sleeve (6) will be extracted, you need to knock out the plastic tread (10). Since the pipe is metal and curved, it will not be possible to align it, you can safely throw it away.
  • Pick up a duralumin, with a similar diameter (internal) instead of an emitted pipe. It will be better if the diameter is slightly smaller than the diameter of the previously extracted sleeve.
  • It is necessary to press the bushing (6) from bronze into the pipe. You may need to squeeze the pipe a little.
  • Express the groove bushing (5) using a hammer. You need to do this very carefully, without making a lot of effort, so as not to deform the sleeve (6).
  • Tread (10) is cut to the desired diameter and tightly inserted into the bar.
  • In the case when the tube you have chosen will have a large external diameter, and you cannot insert it into the hole of the motor head, you will have to pave it to the desired size.
  • Instead of a flexible shaft, you can take a steel rod and connect it to the edwal shaft (you will need the help of a turner).
  • The screw is fixed to the shaft using a nut (2).
  • The bar with an internal shaft is attached to the motor with adapters made specifically in a lathe. There is no universal drawing of adapters, since different models of trimmers can have their own design features.

Using a gearbox from an angular grinder

Also, for the independent manufacture of a boat engine, based on a trimmer for grass, a gearbox is often used from corner grinder, but with some improvements.

  • It is necessary to disassemble the gearbox, and instead of a shaft with a gear, order a new, longer one (respectively, a trimmer for grass). The end of the shaft is made similarly to the extracted (short) so that you can use the same bearings and gear.
  • It is advisable in the place where the bearing is installed, install the oil seal so that the water does not fall into the gearbox.
  • The gearbox body is twisted using sealing gum and sealant.
  • You can fill the lubricant inside the gearbox, or cover the gears abundantly with thick grease.

Production of a screw

To make a screw for the boat engine, you can use a small piece of duralumin 2 mm thick. For the screw, you will need a strip of 30 mm wide and 100 mm long. Make it according to the drawing below.

By step step, the following is meant: if you place the propeller on the table, then from its surface to the blade there should be a distance equal to 10 mm. The angle of inclination of the blades is easy to adjust with the help of pliers, after preliminary annealing duralumin.

This option is not final, and on the Internet you can find a lot of screw drawings with two blades, with three blades, as well as different dimensions. In each case, the size of the propeller is selected individually.

Mount mounts on a boat

The location of the boat engine is called a transom. This part should be strong and reliable. To correctly design the detail, carefully study the technical characteristics of the boat and motor, as the mines creates an additional load. Springs for an inflatable boat consists of:

The edges of waterproof plywood are treated with sandpaper. Loops for metal brackets are installed on the plate. Fasten arches bend with the help of a machine, you can do it manually. Rymes are made of plastic or bought in a store.

How to make a boat motor with your own hands from a trimmer for grass?

To assemble a motor from a trimmer for grass to a boat, the manufacturer will need to prepare the following equipment and materials:

  • household lawn mower;
  • clamp. If it is not, then you can use any other mount for reliable fixation of the motor on the boat;
  • a sheet of duralumin, the thickness of which should not be less than 2 mm;
  • welding machine;
  • set of fasteners;
  • set of screwdrivers and wretched keys.

To assemble a home.made rowing screw, the manufacturer will need drawings. They should indicate the exact dimensions of the blades and the method of fixing them on the axis.

It must be remembered that the lower the power of the drive used and the mass of the boat, the less should there be a blades. For example, a screw with blades 10 × 3 cm is suitable for a boat with a mass of not more than 120 kg.

After the preparation of equipment and a thorough study of drawings, you can start assembling homemade.

The work algorithm should look as follows:

  • First of all, the manufacturer will need to finalize a bent shaft. First you need to dismantle the factory nut placed in a bobbin with a pre.wound fishing line. The nut itself in shape resembles a small 2-centimeter tube with internal thread. If necessary, it can be divided into 2 small full.fledged nuts. During the dismantling of fasteners, you need to be extremely careful so as not to lose them. If this happens, then finding another suitable fastener can no longer work;
  • After dismantling the nut, you will need to dismantle the plastic pad located on the gas button. There are no roller bearings at the end of the standard curved rod. They are replaced by an ordinary bronze sleeve, which is often called a sliding bearing. It needs to be gently extracted. Before this, you will need to unscrew the nut, as well as remove the daily and metal shafts from the tube;
  • Then you need to go to knocking out a plastic tread located on a flexible shaft. In the future, the steel pipe can be thrown away, since it will not be possible to align it with improvised means. It can be replaced by a duralumin pipe with the same diameter. It will need to install a bronze sleeve, which will need to be moved by a canvas using a hammer. Next, you need to take a plastic tread pre.trimmed in diameter, and install it on the pipe;
  • The next step will be the manufacture of the screw. To do this, you need to cut out duralumin blades and sharpen their edges. After that, each blade will need to bend up 1 cm up so that the screw step is at least 10 cm. You can fix the finished device using a nut;
  • Next, you need to install a bicycle speed switch on the boat motor from motorcycles, which will replace the standard plastic lining. After that, you will need to install a silencer that will take the engine exhaust away from the boat driver;
  • To fix the boat engine from the lawn mower, you need to use two plywood sheets. After that, the shaft will remain using 4 screws for this. During the transportation of a boat motor from a trimmer for grass, the shaft can be removed.

The regular ventilation of its standard cylinder will also help to extend the operating time of the boat ICE from a trimmer for grass. To do this, about once every 2 months, you need to twist the spark plug, and it is rarely possible to pull the starter cable 4-5 times. After the procedure, the candle can be screwed back to the place and continue the operation of the engine.

How to make a boat motor from a trimmer for grass

Every fisherman conceived about the replacement of the store for the boat with an alternative engine. It was learned to create from lawnmands, benzos, and even screwdrivers, since their cost is several times lower than the price of a finished sample. The most suitable option is a trimmer for grass, since this device is equipped with all the necessary elements and mechanisms.

Ready set of nozzles

Now they sell special nozzles for remaking a trimmer for grass in the boat motor. Such a prefix includes everything you need for fastening to the gasoline motor. The control handle and the switch button are mounted to the rod. The gas handle is made with the possibility of switching speeds and equipped with a rattle, which fixes the necessary position.

The kit includes a device for installing a device on a boat. The nozzle for a trimmer for grass can be collected easily, it has a simple design. For assembly, you should attach the gas cable to the motor, and then fix the muffler cable. The nozzle costs about 5 thousand in a specialized store. rubles.

Do.it.yourself motor motor

You can perform a home.made boat motor from a trimmer for grass. First you should prepare materials and tools:

  • trimmer for grass with a capacity of 3 liters.With.;
  • steel sheet 2 mm thick for the screw;
  • welding machine;
  • fasteners;
  • clamp for installing the engine on board the boat;
  • corner grinder;
  • drill.

Before work, you need to create drawings indicating all the sizes necessary for the work of parts and nodes, as well as the scheme and installation procedure.

It is necessary to find out the size of the screw, which depends on the power and weight of the boat with the load. It should be borne in mind that the screw with sizes 3×10 cm installed on the ICE can transport a boat with passengers with a total weight of up to 120 kg.

installation, trimmer, grass, boat, motor

Stages of work on the manufacture of a benzo.cash motor:

  • To make a motor for the boat, first you need to redo the bent shaft.
  • Then make a screw.
  • Replace the engine plastic overlay with a switch.
  • Attach the shaft to the engine from the mowing.

Alteration of the curved shaft

First you need to redo the curved shaft. To do this, take a nut 2 cm high in the shape of a cylinder with a cut inside. The unscrewed nuts and bolts must be preserved, since they have a non.standard thread. Then redo the bar with a hard shaft. They pull out a flexible shaft from the rod by removing the nut.

The end of the bar does not have bearings, they are replaced by a sleeve, so it needs to be cut out. Remove the tread. Since the metal pipe is curved, it is difficult to align it, so it will not be used. Instead, you should choose a duralumin pipe of the same diameter, or smaller than the diameter of the sleeve.

installation, trimmer, grass, boat, motor

A bronze bushing is installed in the pipe. To do this, slightly rub the pipe. Then you should carefully adjust the sleeve on the groove with a hammer. At the same time, it is not recommended to make efforts so that the sleeve does not deteriorate. The tread is cut to the desired diameter and put in the bar. If the tube has a large diameter and it is difficult to put it in the hole of the ICE head, then it should be sharpened to the required size.

Instead of a flexible shaft, take a steel rod and connect it to the engine shaft. Then twist a screw onto the shaft and fixed with a nut. Then you need to fix the bar with the inner shaft using adapters to the engine. They need to be performed in a lathe. Different models of mowers can have features that need to be taken into account.

Using a gearbox from an angular grinder

To create a engine on a boat on the basis of hayfields, a gearbox is often used from corner grinder. It needs to be finalized. The shaft with a gear must be replaced with a longer one, which will correspond to the bar. The end of the shaft is performed by analogy with the extracted short shaft so that the same bearings can be used.

In the places of installation of the bearing, the oil seal is mounted, which will protect the angular gearbox from water getting. The gearbox body is twisted using a sealant. Breed into a gearbox to cover the gears.

Production of a screw

To create a screw, you need a duralumin strip of 100 mm long and 30 mm wide. If you put the screw on the table, then from it to the blade should be 10 mm. The angle of inclination of the screw blades must be adjusted with plots. Before that, annealing duralumin is performed. You can make screws with 2 or 3 blades, various sizes. Propeller dimensions should be selected individually.

Experience in remaking the lawmaker-libimmer for grass in the boat motor

In winter 2006 bought two.stroke manual 1 liter.With. Shindaiwa Home-Pro (model 22F), and converted into an auxiliary motor-lover to a sailing catamaran. To overcome narrowness, movements in Stihl, and t.P.

General view of the boat engine from the lawn mower

General view of the boat engine from the lawn mower

A screw for the engine from the lawn mower was chosen with a diameter of 115 mm

Protective ring nozzle to protect against screw

Rowing screw with a stubborn puck, fluoroplastic bearing.

Gas handle, stop button.

Silencer: a regular exhaust pipe is brewed, a new one is installed in the other direction

After the May Day tests on the water, a new, three.lobed screw was made (turned out to be heavy).

Installation for “wind”

Guides.

Games with Schindai are over, sold to a good person. I saw, the fuse and bought 4-tactage, 1.6 liters.With. Elmos EPT-40F braid, with a straight long bar and a hard shaft. I begin the construction of a new, more powerful motorcycle.

Type of motor from the shaft. The standard Opylek on the ground is deployed up, it turned out a convenient and strong handle for carrying the unit.

Type of motor from the front sotoron. Wide textolite support-renewal, the second handle for convenient manipulating the engine while moving.

Stop button. To the right. Wouse lid for pouring oil into the crankcase.

Carburetor throttle control. speed switch from Soviet racing bicycle.

installation, trimmer, grass, boat, motor

Release system. Muffler and adapter for flexible metal.burning.

General view of the motor from the muffler.

Daidwood with traverses for ring nozzle.

The knot of the ring nozzle.

The knot of the ring nozzle.

Ring nozzle assembly with Deadwood and Rowing shaft

She is from the side.

The exhaust pipe is finally laid and fixed.

Rowing screw (first, trial).

Experimental screws. Search for optimal 🙂

Comparison and assessment of the traction qualities of various screws 🙂

Transform Grass Cutter Machine Into Rudder Boat Propeller Drive

Unfortunately, the four-stroke engine Elmos EPT-40F did not justify the hopes assigned to him. Either the poor.quality metal of the sleeve, or I overloaded it without running it properly, but the compression decreased quickly, difficulties began with launch (subsequently dashed on the sleeve, were found). In general, it was risky to take such an engine planned a serious campaign. And two weeks before the start, a difficult decision was made to buy and quickly convert another brand brand mower. So there was a return back to the two.stroke “shindai”, only a little greater power (model Shindaiwa C230. 1.2 l.With). I managed to redo it, but rolled up on the route 🙂

Advantages and disadvantages of using a trimmer for grass

Consider what the benefits of using a trimmer for grass are:

  • Do not have to buy an expensive boat motor.
  • ICE made from a trimmer for grass spends less gasoline than a boat motor.
  • The engine from the lawn mower is more compact than the factory engine for the boat.
  • The engine of the lawn mower has high strength, tightness of the case, the presence of a built.in tank.
  • It has all the nodes that are needed to control a homemade engine: starter, gas lever, bar, shaft, fuel capacity.

Do not forget about the disadvantages of such an alteration:

  • The gasoline engine from the trimmer for the grass is low.power, and it will be difficult or impossible to swim with it on a boat against the current. For the same reason, he will not cope with a heavy ship.
  • A boat for a boat made of motorcycles is suitable for moving around reservoirs with standing water, which may not suit lovers of active fishing on the river.
  • Also, an important minus is an increased level of noise of the trimmer motor for grass, and some models can smoke.

Principle of operation

The engine for a boat from a trimmer for grass has a higher speed of the blades, which allows you to move faster along the river. When a gas station works when cutting the lawns, its blades are twisted in the other direction. In the manufacture of a motor for the boat, engine blades are turned over. Then the engine will work to push the boat. The higher the blades are located to the surface of the water, the faster the speed speed and the higher the speed of the boat.

How to make a boat motor with your own hands from a trimmer for grass?

To assemble a motor from a trimmer for grass to a boat, the manufacturer will need to prepare the following equipment and materials:

  • household lawn mower;
  • clamp. If it is not, then you can use any other mount for reliable fixation of the motor on the boat;
  • a sheet of duralumin, the thickness of which should not be less than 2 mm;
  • welding machine;
  • set of fasteners;
  • set of screwdrivers and wretched keys.

To assemble a home.made rowing screw, the manufacturer will need drawings. They should indicate the exact dimensions of the blades and the method of fixing them on the axis.

It must be remembered that the lower the power of the drive used and the mass of the boat, the less should there be a blades. For example, a screw with blades 10 × 3 cm is suitable for a boat with a mass of not more than 120 kg.

After the preparation of equipment and a thorough study of drawings, you can start assembling homemade.

The work algorithm should look as follows:

  • First of all, the manufacturer will need to finalize a bent shaft. First you need to dismantle the factory nut placed in a bobbin with a pre.wound fishing line. The nut itself in shape resembles a small 2-centimeter tube with internal thread. If necessary, it can be divided into 2 small full.fledged nuts. During the dismantling of fasteners, you need to be extremely careful so as not to lose them. If this happens, then finding another suitable fastener can no longer work;
  • After dismantling the nut, you will need to dismantle the plastic pad located on the gas button. There are no roller bearings at the end of the standard curved rod. They are replaced by an ordinary bronze sleeve, which is often called a sliding bearing. It needs to be gently extracted. Before this, you will need to unscrew the nut, as well as remove the daily and metal shafts from the tube;
  • Then you need to go to knocking out a plastic tread located on a flexible shaft. In the future, the steel pipe can be thrown away, since it will not be possible to align it with improvised means. It can be replaced by a duralumin pipe with the same diameter. It will need to install a bronze sleeve, which will need to be moved by a canvas using a hammer. Next, you need to take a plastic tread pre.trimmed in diameter, and install it on the pipe;
  • The next step will be the manufacture of the screw. To do this, you need to cut out duralumin blades and sharpen their edges. After that, each blade will need to bend up 1 cm up so that the screw step is at least 10 cm. You can fix the finished device using a nut;
  • Next, you need to install a bicycle speed switch on the boat motor from motorcycles, which will replace the standard plastic lining. After that, you will need to install a silencer that will take the engine exhaust away from the boat driver;
  • To fix the boat engine from the lawn mower, you need to use two plywood sheets. After that, the shaft will remain using 4 screws for this. During the transportation of a boat motor from a trimmer for grass, the shaft can be removed.

After the homemade nozzle is ready, it will need to run into. To do this, prepare a fuel mixture of fresh gasoline and motor oil in a ratio of 40: 1. After that, you will need to pour the finished mixture into a standard boat engine tank, start it, and let it develop 1 full fuel tank at idle. After running in, a home.made boat motor from a trimmer for grass will be completely ready to work.

Making mount and installation on the boat

To install a home.made motor on an inflatable boat, you will have to make a special mount. The following option is possible: the ring is used, to which the belt is attached. To connect the product with a transet, it is permissible to use an old unnecessary meat grinder. To do this, the lower part is cut in it, and a hole is drilled in the transverse plane with a diameter of 12 mm. This will also require a hairpin, with a diameter of 12 mm and a length of 100 mm. One side must be flattened and drilled a hole with a diameter of 6 mm. The m6 bolt is inserted into this hole, after which the eye of the braid braid is attached to this bolt using a nut.

The homemade device is installed on the boat in this order:

  • Homemade is attached to the transit of the boat with a hairpin and nut.
  • After that, the engine is mounted and fixed using the corresponding connection. Then it is checked how the motor rotates in one and the other.

Fishermen are such a category of people who constantly come up with something. Many fishermen just like this process, and other fishermen just do this, because they have no extra money to buy a new boat engine. There is such a category that is available to purchase a boat and a boat motor at once.

Installing a home.made motor is a difficult procedure that requires certain skills, and not everyone can make such a fairly simple device. Firstly, you need to have a desire, and secondly, there should be conditions for its manufacture. In addition, it must be remembered that everything should be done firmly and reliably, since the water water does not forgive. If the cylinders are damaged, then the result of fishing can be unpredictable. You should not count on distant transitions in reservoirs, since a home.made design is not a completely reliable design. Despite this, a home.made boat motor is able to significantly make life a fisherman.

| Denial of responsibility | Contacts |RSS