Mow hay with a motor block with an adapter. The price of a rotary mower to a walk -behind tractor

How to install a rotary mower on a single tractor

Speaking of a rotary mower, it implies a device with which a vegetation cover is mowed, growing in the fields and meadows. It can be agricultural crops or weeds that should be eliminated if herbicides are not used.

This is the name closest to the speedy perception, giving an idea that the principle of its work is the functionality of the discs available on it, with which the mushroom is carried out.

The rotary type of pigtails is connected to the walk.behind tractor in three main ways:

In the same way, there is a separation of this type of pigtails according to how the cutting devices are located in relation to the unit on which they are fixed:

All about how to make an electric mower with your own hands.

Looking here, you can watch a video mini.tractor from the Neva walk.

one.axle tractor with a hay

So, as a result of long torment selection and compromise searches, it is purchased:

There were already reports on the walk.behind tractor, I will not repeat myself. The engine is magnificent, the swing of the assembly of everything else is Soviet. In particular, after 5 minutes of working with a whistle, a bolt flew out onto the engine shaft pulley. It’s good that the shield stood. And after 10 minutes of work, the knob was lost from the speed switch, stupidly unscrewed despite the found traces of the glue, but then found the elastic band from the right hand and so on. In general, you need to glue everything and tighten everything. The most important claim is the bolt that attaches the steering wheel to the walk.behind tractor, according to the design of the designers, it should provide a slight rearrangement of it on the side to go from the side block. In fact, it turns out that the entire steering wheel is attached to the base with a bolt on which is probably up to the middle of the nut, t.e. Just pressed. You have to pull up constantly. I think to cut the thread on the bolt to drag it through this node and tighten it with a nut from below. Of course it will be more difficult to rearrange the steering wheel, but constantly pulling it up is not a matter.

Now on the mower. I immediately discovered that the shaft on which the stretch video is placed is not parallel to the main structure, as a result, after installing the tensioner, it turns out that the video spares the trajectory of the belt movement. Cured the bend of the tensioner for which the video is installed. Let’s go The first belt was killed for about 15 minutes The most filthy that even a slight weakening of the belt, as a result of its overheating, leads to that it is no longer possible to use it, because its tension is carried out by a proliferator or rearrangement of one “hole” on the console itself. As a result, the belt is pulled out and the tensioner is no longer enough, and the rearrangement of the braid leads to the fact that even with the lowered tensioner lever the belt is still stretched, and I didn’t want to try something with the “connected” load, in my opinion this is wrong. We change the belt, the attempt number 2 rushes like a tank, cuts everything and everything, but if the grass is thick or settled, it is better to mow small squares, t.to. A whole stack of tangled grass is assembled on the mowal frame, which, first of all prevents the knives from rotating, secondly falls and crushes grass from the side. I got so embarrassed-I do it after 5-7 meters, such as the “pull”, I hand over, and then Kosh is perpendicular to these crooks to dump them in them what gathered on the frame. As a result, with this approach, with a very difficult nomadic area, dense grass and places already burned in 2 hours, it was possible to mow about 6 acres, with pauses for cooling the belt (it was the last, and to the city of 150 km) and the scattering of already mowed grass.

Summary: Little, despite the above shortcomings. If mowed before two weeks, it would be much easier.

Review of other options for hay harvesting devices

If in the configuration of a walk.behind tractor or motor.cultivator there was no sufficient number of hinged devices, owners have to either buy various nozzles, or make them with their own hands, taking into account specific needs. Each owner solves these issues in his own way.

Thanks to the possibilities of modern production, consumers are offered in a wide assortment various options for moving cultural and wild herbs, cleaning in rolls, mowing and grinding weed herbs, transporting to the place of storage. Collection presses and roller compactly packing hay and straw, haywoods turn over hay for optimal drying.

Rabble-lumps

Depending on the method of aggregation, nozzles can be tape, lateral, transverse with rings. Some models can be used not only for hay assembly, but also for cleaning the territory and snow cleaning, no worse than standard screw.core snowpliters. In a specialized network, you can find prefixes for a walk.behind tractor in a huge assortment for the most demanding and picky hosts.

Homemade nozzles and devices for spiting, hay harvesting and packaging in bales is generally difficult to cover with any classification-people’s craftsmen and craftsmen manage to create a unique multifunctional equipment, the price of which is an order of magnitude lower than factory options, and the quality of manufacture and functioning is not inferior to industrial samples.

In addition to the most common models of rotary (disk) and segmented mowers, chain mowers are also made. This is a fairly rare option, since chain braids are a very traumatic device. Chain mowers work as a crusher of grass, require more power and are more often used in aggregation with tractors or mini-tractors.

Make sure how clearly a plan and a sequence of actions are thought out when creating a rake for a walk.behind tractor:

Mitch for a walk.behind tractor

Increasingly, you can see how the owners of summer cottages and small farms perform haying in a motorcycle unit. There are several varieties of this equipment that differ not only externally, but also the principle of action.

On the market you can find and choose the following modifications:

Frontary models are divided into two categories:

Rotor mower with a walk.behind tractor choosing attaching equipment for yourself, it is worth considering the following features:

How the grass will be stacked:

  • in the rolls. this option will allow you to quickly form a stack without involving additional equipment (rake);
  • In mowing. the grass in an even layer covers the lawn, additional equipment will be required to collect and lay it;
  • Mulching. grass is crushed, becoming natural fertilizer for plants (shrubs, trees, etc. D.).

Capture width. depends on the specific model.

Method of aggregation with a motorized device:

  • in front of the walk.behind tractor. the most popular option;
  • Behind. these are chain lawn mowers used more and more for cultivating lawns;
  • from the side (half-waver)-the support wheel takes on the main weight of the mower, such models are more relevant for mini-tractors.
  • The power of the haying unit. The higher it is, the more functional the nozzle is. with its help it will be possible to mow not only grass, but also a shrub, the shoot of young trees up to 3.5 cm in diameter.
  • Rotation frequency of the working organs of hay.

Rotor mower

The rotary nozzle on a one.axine tractor can be attached in all three ways (back, front, from the side), depending on the location of the cutting organs in a particular model of a mower.

Dawn “dawn”

Dawn-1 mower

The lineup of disk (rotor) braids involves the presence of one, two, or three discs that are fixed on a hard frame. The support wheel connected to the working organs of the mowing is attached to the same frame by transmitting. This supporting wheel with its rotation drives the working organs of the haymaking.

The main application of the rotary mower to the walk.behind tractor with VOM:

We suggest watching a video of the disk (rotor) mowing for a walk.behind tractor:

Segment mowing

The segment mower for the walk.behind tractor is a variety of frontal haymaking, is designed for mowing herbs and hay in territories with different relief, and the grass is cut directly under the root. Such hayfields can be attached in two ways to the walk.behind tractor:

  • in front with a drive belt (it is better to use a three.armed pulley);
  • behind, using a power shaft (VOM) and a special adapter (adapter).

The nozzle is used for both soft and hard herbs, and stubeen is relevant for mowing.

Senocoserian segment 9G-1.four

Semetal Front Scout SM-110

The design is very simple and unpretentious in care. The haymaking of a rigid frame consists of a hard frame, on which two bars with cutting elements (fingers) are fixed, one of which is completely motionless, the second makes reciprocating movements to the right and right. The principle of scissors. grass falls between the cutting edges and is cut off by them.

We suggest watching a video of the Chinese haying for a walk.behind tractor:

Chain mowing

This is also a type of frontal mowing on a single tractor, however, chain modifications are aggregated with a motorized device only from behind. The height of the cut is regulated by a special roller. The nozzle allows you to mow not only grass and hay, but also a shrub with a thickness of up to 3 cm. These are rather heavy nozzles, their weight may exceed 100 kg.

KM-0.5 mower

About how the chain mower works on a single tractor will tell

Mitch for a walk.behind tractor

Increasingly, you can see how the owners of summer cottages and small farms perform haying in a motorcycle unit. There are several varieties of this equipment that differ not only externally, but also the principle of action.

On the market you can find and choose the following modifications:

Frontary models are divided into two categories:

Rotor mower with a walk.behind tractor choosing attaching equipment for yourself, it is worth considering the following features:

How the grass will be stacked:

  • in the rolls. this option will allow you to quickly form a stack without involving additional equipment (rake);
  • In mowing. the grass in an even layer covers the lawn, additional equipment will be required to collect and lay it;
  • Mulching. grass is crushed, becoming natural fertilizer for plants (shrubs, trees, etc. D.).

Capture width. depends on the specific model.

Method of aggregation with a motorized device:

  • in front of the walk.behind tractor. the most popular option;
  • Behind. these are chain lawn mowers used more and more for cultivating lawns;
  • from the side (half-waver)-the support wheel takes on the main weight of the mower, such models are more relevant for mini-tractors.
  • The power of the haying unit. The higher it is, the more functional the nozzle is. with its help it will be possible to mow not only grass, but also a shrub, the shoot of young trees up to 3.5 cm in diameter.
  • Rotation frequency of the working organs of hay.

Rotor mower

The rotary nozzle on a one.axine tractor can be attached in all three ways (back, front, from the side), depending on the location of the cutting organs in a particular model of a mower.

Dawn “dawn”

Dawn-1 mower

The lineup of disk (rotor) braids involves the presence of one, two, or three discs that are fixed on a hard frame. The support wheel connected to the working organs of the mowing is attached to the same frame by transmitting. This supporting wheel with its rotation drives the working organs of the haymaking.

The main application of the rotary mower to the walk.behind tractor with VOM:

We suggest watching a video of the disk (rotor) mowing for a walk.behind tractor:

Segment mowing

The segment mower for the walk.behind tractor is a variety of frontal haymaking, is designed for mowing herbs and hay in territories with different relief, and the grass is cut directly under the root. Such hayfields can be attached in two ways to the walk.behind tractor:

  • in front with a drive belt (it is better to use a three.armed pulley);
  • behind, using a power shaft (VOM) and a special adapter (adapter).

The nozzle is used for both soft and hard herbs, and stubeen is relevant for mowing.

Senocoserian segment 9G-1.four

Semetal Front Scout SM-110

The design is very simple and unpretentious in care. The haymaking of a rigid frame consists of a hard frame, on which two bars with cutting elements (fingers) are fixed, one of which is completely motionless, the second makes reciprocating movements to the right and right. The principle of scissors. grass falls between the cutting edges and is cut off by them.

We suggest watching a video of the Chinese haying for a walk.behind tractor:

Chain mowing

This is also a type of frontal mowing on a single tractor, however, chain modifications are aggregated with a motorized device only from behind. The height of the cut is regulated by a special roller. The nozzle allows you to mow not only grass and hay, but also a shrub with a thickness of up to 3 cm. These are rather heavy nozzles, their weight may exceed 100 kg.

KM-0.5 mower

About how the chain mower works on a single tractor will tell

Press Collection for a walk.behind tractor. models, types, characteristics

Hay harvesting is a rather long and complex process. This is a mowing of grass, its drying, loading on transport, transportation, folding. Therefore, the press collection for a walk.behind tractor is an optimal device for household owners.

Advantages of the operation of the preserlier

Press for hay to the walk.behind tractor is actively used by modern farmers.

The advantages of this device are difficult to overestimate:

  • Convenient settings;
  • Neat hay collection in bales;
  • Plants do not crumble;
  • You can form small rolls for the lightness of their carrying;
  • The simple design is easy to repair in case of failure;
  • The ability to create a press with your own hands.

Types of the press of the colleagues

Depending on the method of formation of the bales, the press colleagues are a dull or roller type:

  • Rolonnik for a walk.behind tractor. Straw is collected in cylindrical blocks with a loose middle. The roll is fixed by the twine that simplifies further transportation and storage;

Tulk for a walk.behind tractor. There are large sizes than rolled analogues. Harse enters a special camera, rectangular bales are pressed, tied with twine. This form is more convenient for loading, transportation and storage. The desired density and dimensions of the block are determined automatically, therefore it is very easy to control the equipment.

Roller type presser

The rolled press is the most reassured due to its positive characteristics:

  • Compactness;
  • Small sizes simplify the storage process during the downtime of the device;
  • Affordable cost;
  • Simplicity in work;
  • The ability to make the middle of a billy uncomplete;
  • The resulting blocks have the same size.

Rolled models have a lower processing width and speed than a similar technique of standard type, but they can be used with most motoblocks.

The design of the hay presser for a roll.type motoblock:

  • Drum;
  • Lattice;
  • Pressing belt;
  • Conveyor;
  • Stretch and knitting node;
  • Shaft;
  • Electrical system (sound signal and lightindicators);
  • VOM Power Plant, setting the unit in motion.

The presser of the embossed type

The press collection press is slightly different from the rolled analogue. The design of the device includes a screw for receiving-handicrafts, a press block and a knitting unit. The same.based tractor drives the power shaft of the power of the power plant used.

The salesman has quite compact sizes, and also has the following features:

  • A fairly high level of performance;
  • Automation system. The model of the wireman will be optimal, in the configuration of which the loader and the apparatus for knitting bales.

Popular models

The assortment of the press of the colleagues for the motor blocks is quite large. It is worth paying attention to several interesting models.

Senian colleague PPR-50. The model is installed on Neva walk.behind tracts, has an affordable cost and good performance. The device is suitable for technology with a power of 10 liters. With. But such a press for the Neva walkover without a protective casing, because a small amount of hay falls through the rollers.

Parameters of the device model:

  • The width of the coverage is 80 centimeters;
  • The maximum weight of the finished bale is 20 kilograms;
  • Briket dimensions (in length/width/height). 250/160/150 centimeters;
  • Speed ​​- up to 6 km/h;
  • Minimum motor power. from 10 liters. With.;
  • Device weight. 350 kilograms.

Minter Mini Mini R-500. The Italian unit, which is characterized by high maneuverability, the possibility of use in large territory, high performance and reliable equipment.

  • Capture width. 130 centimeters;
  • Minimum motor power. from 11 liters. With.;
  • The maximum weight of the finished bale is 55 kilograms;
  • Briket dimensions (length/width/height). 180/140/120 centimeters;
  • The mass of the device is 520 kilograms.

Presser RXYK 0850. A device with a high power level and the ability to work with rude feed. Compact cylindrical bales are formed, they are easy to load and transport.

  • Processing width. 80 centimeters;
  • Working speed. 5 km/h;
  • Motor power. from 24 liters. With.;
  • The size of the briquet (in length/width/height). 115/130/120 centimeters;
  • The mass of the device is 390 kilograms.

Model M60 Mini press. A dumpling type device that has a reliable design, compact dimensions and the ability to set up the capture width.

  • Processing width. 105 centimeters;
  • Minimum motor power. from 20 liters. With.;
  • The dimensions of the briquet (length/width/height). 160/390/135 centimeters;
  • The mass of the device is 900 kilograms.

Homemade press collection for a single tractor in parameters may not be inferior to the acquired unit. If you make a device with your own hands, it is worth focusing on the technical characteristics of the used motoblock.

The purchased or made press of hay can save forces, time and finances, as well as prepare food in the season.

Complex nozzles

Complex nozzles are a type of walk.behind stationary equipment. They are purchased for processing a land plot, seasonal care of a plant culture, harvesting and other economic needs. Thanks to them, sowing occurs in the shortest possible time, when the score is on a matter of days. Motoblocks are equipped not only with seed seeders, but also with potato. In addition, a large number of equipment are intended for other use. Having familiarized yourself with simple nozzles, let’s try to deal with those that include complex.

The plow is perhaps the most popular mounting equipment for a walk.behind tractor. It can be fully evaluated by those who had to dig a land plot for long days. The technique equipped with a plow will plow the field quickly, completely taking physical labor on itself. The plow is able to plow the ground to a depth of 15-25 cm. At the same time, it looks quite simple, in the form of a steel plate on a metal lever, with an element. Simplicity of design allows many craftsmen to make it on their own. This mechanism is ambiguous, it has its own varieties.

  • The plow is standard. Endowed with a wide lime (with a knife) and bent dump, which gives it the opportunity to cut weeds and turn over soil layers.
  • Revolutionary plow. A more complex design, which is two plows, fixed at a certain angle on the frame, with dumps “looking” in opposite directions. While one plows the soil, the second is in a state of reserve, they change the plow on the next furrow, this greatly simplifies the work of the plowman.
  • Zykov’s plow. This device flips and grinds the soil layer more qualitatively due to the improved shape of the dumpy plane.

Harrow

With the help of this design, the plowed surface is aligned. Equipment in the form of a steel grate with sharp spikes looks, thanks to which the harrow is called tooth. There is another type of harrow. disk. It differs from the tooth presence of spinning knives made in the form of disks.

Such a model is a better looser, it copes better with grinding and alignment of the soil.

Helpers

The name of the equipment speaks for itself, this is a design that helps to hide the plants. In addition to pouring the soil to seedlings, the hillock forms furrows and even falls asleep with the seeds. There are different types of cummers.

  • Lister-the simplest model with two motionless wings and a constant width of the soil, creates a row of 20-30 cm. It is clear that such a device does not regulate the width of the capture, so you will have to be content with the aisle, which the cigns is capable of. Lister equipment is hung on lightweight types of equipment.
  • The hip with a variable capture width has mobile wings and is regulated, so the distance of the aisle can be changed at its discretion. Such a nozzle is used for equipment that has a power of at least four horsepower. Unfortunately, this is energy.consuming work, since part of the Earth from the educated tubercles is poured back to the holes.
  • thought out a disc hir. It is easy, efficiently, efficient to work and the generated ridges are much higher for him. Buying a cupboard, it is worth choosing large.sized thick disks from alloy steel. Such a purchase will cost more than such models, but after it it is difficult to switch to other equipment.
  • In terms of quality, the Dutch.type cigarette baker is inferior to a disc one, but surpasses usual in that its wings in corners are capable of moving up and to the sides. The design allows you not to do excess work and reduces the energy intensity of hilling.
  • Propeller (active) in quality is not inferior to the disc. The principle of operation is different: with the help of blades, he grinds the soil along with weeds and makes loosened embankments.

Cutters

The most encountered type of equipment intended for field work. Cutters plow easily, loosen the soil, riding it from weeds. With their help, you can make fertilizers and special top dressing. This equipment is diverse in shape, quantity and place of location of knives. It looks like an axis with plate knives mounted at different corners, which, when rotating, enter the ground. If you put blocks with cutters from the sides of the walk.behind tractor, they will replace the wheels.

How to choose?

The choice of attachment equipment to some extent depends on the power of the motor block motor. This technique is of three classes: light (household), medium (semi.professional) and heavy (professional). The shaft with capacity selection promocratively increases the capabilities of the equipment, with its help, attachment equipment is equipped.

Hinged nozzles for different types of economic activity are often more expensive than a walk.behind tractor itself. To make a choice, you should think what work is the most time.consuming. For them you can choose more complex equipment. Simplified nozzles are quite affordable to do it yourself.

Sometimes they do not know what is better to choose for soil processing. mills or plows. For a choice, you should study the soil features of your site. For plowing a field with soft soil, milling cutters are used, and a plow is used to work on solid ground.

Choosing a small one-axle tractor for a summer residence, many turn to the MF-70 Czech production model. It can be used to mow grass on the site, cleaning snow, delivery of small cargoes. Thanks to the compactness and maneuverability of MF-70, they are used to work in hard-to-reach places. To help gardeners and gardeners, a new model of the Motoboblok Stavmash BM-15 has been developed. This technique has already established itself well, with the help of nozzles, any work is performed on the garden.

The Brado BD-1600 Tractor Tractor is purchased for work on small farms. It is equipped with the strongest four.stroke engine that works on gasoline. The technique weighs 120 kg, is capable of producing a depth of plowing up to 30 cm. Self.Procedure Unoa SW 360 (Sungarden MF 360 S) is intended for professional use. The technique has a large selection of equipment, the replacement of which occurs without the use of tools.

The same.based tractor with mounting equipment will facilitate the work of a summer resident with a small land plot and a farmer with a field of medium.sized. The executed volume of work directly depends on the power of the engine and the specifics of the nozzles.

Pros and cons

The main advantage that has a dawn rotary mower (for the Neva and analogues) is the possibility of folding mowed hay in neat rolls. The function significantly facilitates further processing. In the presence of too thick grass, this approach increases the time of drying. The tool under consideration is safer than cutting modifications, since it has protective fuses. However, one should not forget about security measures, you must not allow any contact with the disks and cutting knives with the state on.

The disadvantages of this mower include the rapid wear of the drive belt. This is due to the fact that when processing sites with different relief, the working part of the device has some freedom of movement in relation to the motorcycle unit. This leads to a violation of the dressing position of the drive and motor pulley, which helps to accelerate the wear of the belt and its deformation. Having the necessary skills, you can adapt a more rigid connection, without losing the possibility of free movement of the working unit.

Motoblocks and mowing suitable for them

Each mower is designed for a certain model of a walk.behind tractor, so it corresponds to it:

“Neva” MB-2

This device appeared in 1985 and immediately gained popularity among customers thanks to its versatility.

It is equipped with a shom, and the speed adjustment range is 1.8-12 km/h.

The manufacturer of this model is Red October OJSC, which is a fully compatible KR-0.5 Neva mower.

This mower is a single.rope with a mowing width of 55 cm and weighing 35 kg. The optimal speed of mowing of grass is 1.8-3.2 km/h, which allows you to mow grass in an area of ​​900-1500 m2 per hour. The mitch can be installed on any Neva walk.behind shoes, as well as other models with a similar method of attaching and location.

OJSC “Kaluga Engine” produces dawn rods (KRN-1) with belt drive (chain transmission in such devices is rarely used), completely compatible with MB-2 and other similar devices. KRN-1 is equipped with skis that protect knives from a collision with the soil, as well as the same height of herbal mowing. The width of the capture of 80 cm provides fast mowing of any grass up to one meter high, as well as small single shrubs and young wooden shoots.

MTZ “Belarus”

The first models of these motoblocks appeared in the mid.seventies of the twentieth century as a replacement of manual and horse traction on personal farmsteads. All devices of this series due to heavy weight are difficult, but the power of their engines is not too high.

Motobes MTZ are equipped with engines from various manufacturers, but the overall design is always the same.

2 models of mowers are compatible with MTZ “Belarus”:

KRM-1 is a single-rope device with a capture width of 60 cm and a weighing of 45 kg, its performance is 1200-1500 m2/h, and the adjustment of the mowing height is not provided for.

KRM-2-single-rope device with additional front wheels and manual adjustment of the height of mowing. In its design, closer to traditional lawnmands, because the cutting disk is closed by the case (deck), so this attachment device not only cuts off, but also grinds the grass.

“Salute”

This uniform tractor was developed by the Salyut scientific and production enterprise in the mid-nineties of the twentieth century, but only in 2002 went into mass production.

In 2012, production on the territory was turned and brought to China, so all devices under this brand released after 2012 are Chinese, albeit under the control of specialists.

A distinctive feature that makes the “salute” a direct competitor of the “Neva” is the belt drive and shom located on the left side of the apparatus.

The most popular hinged equipment for mowing grass, which is installed on this device, is the “Lander” KRN-1M-a two-rot braid with a belt drive, a constant mowing height and an capture width of 80 cm.

The skis installed on the sides protect the knives from a collision with the ground and limit the minimum mowing height. In its design, it is almost completely identical with the dawn described above, therefore it is suitable for installation on any motoblocks with belt drive.

Motobogloks “Ugra” produces OJSC “Kaluga Engine”, and in their design they are very similar to well.established “salutes”.

The device is equipped with engines of different manufacturers, including market leaders as:

For this, the walk-behind tractor from the Kaluga Engine produces the dawn mowls (KRN-1) with a drive from VOM. They differ from the “dawn” for the “Salute” or “Neva” motoblocks only by the drive system, and the rest is completely identical.

Thanks to a simple design, such hinged braids often collect various small enterprises that have access to cheap Chinese components and the necessary equipment.

“Brait”

Under the brand “BRAIT” sell motoblocks of various types made at the PRC factories.

The real owner of the brand is unknown, but the products under it are distinguished by a good quality of manufacture and low price, so it is in demand.

Due to the fact that motoblocks of both types are available under this brand, it will not be difficult for them to choose a hinged mower, because even if the standard mount is not suitable, you can buy a installation kit, that is, a universal adapter.

For devices with VOM, the same hinged devices that are installed on USRU and other devices equipped with a power selection shaft. The same models are suitable for motoblocks with whas as for “Neva” MB-2.

Therefore, KRN-1M, produced at an unknown Chinese factory, is suitable for both the apparatus and for any other, equipped with Shom.

This heavy one-legged tractor weighing 160 kg was developed in the mid-90s of the twentieth century at the Ufa Motor-Building Production Association (UMPO) as part of reorientation (reprofilization) for the release of consumer goods.

A large weight and a powerful motor made this device very popular, and VOM provided the ability to connect various attachments to it, including mowers.

Due to the standard for motoblocks of this type of design for installation on “Argo”, any braids operating from a power selection shaft are suitable. In addition to the above KRM from MTZ, as well as KRN-1 with a drive from VOM, you can install a mobile to KM-0.5 on Argo on Argo. This mower is a copy of KRM-2, only manufactured at another enterprise.

Patriot “Ural”

Despite the fact that Patriot has arisen in the United States, and the main plants are in the PRC, the Ural model is assembled on the territory of the Patriot Ural. this is a heavy multifunctional one.legged tractor with a belt drive and shom, therefore, most mowers are suitable for installing it. type.

On the manufacturer’s website, the KRN-1 model is available, which is no different from the mowing mowed already described above with the same name. Any other hinged devices operating from Shom are also suitable, however, some may require a universal installation kit (adapter).

“Virginarina”

Motobogloks under the Znetina brand are produced by the Academy of Tools, which produces both types of devices, so any compatible attachment equipment compatible for connection is suitable for them.

How to plow a motor block with milling cutters correctly

The appearance of milling plants for motoblocks has greatly simplified the procedure for cultivating land for many gardeners. Instead of traditional works, such as plowing and harrowing, a comprehensive operation has appeared, which allows you to get a loose soil structure 1 time suitable for sowing work. This significantly reduced labor costs and gave a significant winning time.

How to adjust the depth of plowing with a motor block with milling

The maximum depth of cultivation by a motorcycle unit (it is more correct to call the process of plowing with cutters) to the greatest extent depends on the diameter of the cutter and usually half of this value. Attempts to plow to a great depth will lead to the fact that the cultivator will simply be overwhelmed. Adjust the deepening to the soil within the required limits using a coupon.

How to dig a garden with a motor block with milling

The standard process of cultivation of the Earth by a motor block is usually carried out in 2 stages.

  • Install a couch on a small deepening. They process the plot throughout the area, bypassing it in a circle and gradually shifting to the center. At the same time, the cultivator works at small speeds or in the first gear.
  • Set a couch to the required depth of cultivation. The site is processed over the entire area at high speeds or at 2 speeds.

As a rule, to dig a previously processed area by a motor block, 2 passes are enough.

How to plow the virgin soil with a motoblock with milling

The virgin soil plowing with cutters with cutters is carried out in several techniques. The first passage at low speed with minimal deepening violates the integrity of the turf, destroys the strongest surface layer. On the second and subsequent passages, the deepening is increased, gradually increase the engine speed. In total, 3-4 processing may be required, it is highly dependent on the density and structure of the soil.

Brush hogging (mowing)

Pros and cons

Previously, farmers did not have an alternative, so all the work was carried out manually. Now many can purchase a motor cultivator or even a single tractor. However, some still doubt that the Earth plowed with such technology is of high quality.

The main advantage of using this type of technique is that mechanical plowing takes a little time. The farmer saves time and effort, performance grows, and this affects the level of profit. Having a single tractor, you can abandon the help of employees. As a result, the farmer saves on several salaries.

motor, block, adapter, price

At the same time, using the one.axic tractor, you can not only plow the ground, including the virgin lands, but also plant seeds, collect the harvest, mowing of grass and harvesting hay, as well as do a lot of other useful work without spending a lot of time. It is also convenient that with the help of one device you can simultaneously do several works. So, already during plowing the farmer, it has the opportunity to introduce fertilizers to the ground.

Both the same.based tractor and motor cultivator allow you to deeply dig in the soil. It will not be possible to achieve such results manually. This is especially true for work not virgin. Thanks to the deep plowing, which is provided by the uniform tractor, the cultivated lands become better in terms of structure. Thus, the soil can be saturated with oxygen and properly moistened. This will certainly affect the crop in the future.

The processing of virgin grounds brings a lot of benefits. With the help of this technique, fencing of the soil occurs.

As a result, planted plants grow well on the site, but weeds are excreted.

Statistical data show that after processing the soil with a might block or a motor.cultivator, the yield increases at least twice.

Of the shortcomings, one can distinguish a high plus to this to perform various tasks, additional nozzles will be required. They can be made with your own hands, but some species will still have to be bought.

Very carefully need to use motoblocks on the virgin lands. If there are many weeds with a deeply planted root system in the soil, machining will only harm, since it will contribute to the propagation of harmful plants.

Some farmers believe that the constant use of a walk.behind tractor for virgin lands or a motor.cultivator can lead to depletion of a fertile layer or to its violation, which negatively affects the productivity. But you can solve this problem very easily. To do this, it is enough to make fertilizer simultaneously with the dugout of the soil.

A lot of gardeners and farmers believes that the cultivation of land with a tractor will be much more convenient, and the quality of plowed land is much higher. The first parameter can be considered correct, but regarding convenience, this is not so. Arable work with a tractor will be possible only in large and completely open areas. If there are buildings or trees nearby, then using such a technique will not work. Motobobes are much more maneuverable, and they are many times cheaper than the simplest tractor.

Rotor haymaking and the price of them

We recommend that we buy a rotary mower to agrarians who need to mow a dry diameter of less than 100 mm, thick vegetation or hard residues of sunflower or corn. But the rotary model will cope with the departure of the lawn or a small area in the garden. Aggregate to the drive of the Neva motor block in front or trailer method. The trailed traps mulch the grass, so they are not suitable for farmers that need herbal harvesting on hay.

The operation of the rotary mower is carried out from the belt shaft of the walk.behind tractor. Suitable for Neva motor blocks on gasoline and diesel moves, as in the video. For attaching to the latter, a special adapter includes a complete set. Among the various rotary mowers for Neva, Kaluga Zarya and St. Petersburg KR-05 stand out. Depending on the modification on rotary mowers, 1-2 working discs, the KR-05 working body 1, the “dawn” has 2 disks. On the disk using a moving hinge connection, 4 knives are fixed. The movable codder when the disk moves allows knives under the influence of centrifugal force to turn around and they cut the grass. The Dawn Disks rotate towards each other, the width of the handling of the lawn is larger. The design of the rotary model on special sledges is located, they allow a simple movement to adjust the height of the cut of grass. Small vegetation in even shafts is distributed in two sides and it is easy to assemble it with a pitchfork.

It’s easy to work with a rotary mower, but once a day it is necessary to spin the corner joints and smear the gears with a lithol or machine oil. The technique will last with proper care longer.

Consider the popular segment models for the Neva motornote Read more on video and photo. In the video below you can see how the equipment works on the field and along the road.

Rotary “dawn”

Official manufacturer of the Dawn Rotor Rotor Pitch. “Kadwi”. is located in Kaluga. But the market has many home.made and Chinese models made according to the manufacturer’s schemes “Kaluga Engine”. Outwardly, they differ only in color-at the Kaluga Dawn it is bright red, as in the video. But this is not the main difference. Chinese quality is worse, since low.quality material is used for manufacturing.

The official “dawn” for the Neva motornote showed itself in use well. Chinese and homemade mowers are just fakes, although among them you can find models of acceptable quality.

Characterization of the haying “Dawn” for the Neva walk.behind tractor and the price of analogues and licensing equipment in the table:

TX “Dawn” Indicators
Performance 0.2 ha/hour
Maximum speed 2-4 km/h
The width of the capture 800 mm
The speed of rotation of the working bodies 2000-2400 vol./min.
Maximum height of mowing grass 100 cm
The weight of technology 35 kg
The price of the official model/Chinese analogues 12 500/11 700

You can buy cheaper directly from the manufacturer in Kaluga. The retail price is 10-15% higher and it is more profitable to buy in bulk. Spare parts from the domestic model are suitable for all Chinese analogues, therefore, in some cases, you can not overpay. The price of used equipment starts at 5,000, but we do not recommend purchasing equipment over 10 years old.

Rotor mower of KP.05

Officially, KP-05 is produced in St. Petersburg at the Krasny October factory. The model is official to the Neva MB-1 and MB-2 motornote. It is impossible to find accurate analogues in the market, but there are similar mowers with low quality. Many years of experience and advanced technologies allowed the manufacturer to develop an optimal, functional and small rotary mower KP-05. Read more Model in the work, the reader can consider on the video.

The weight of the technology is smaller than the Zarya model, so the KP-05 is convenient for summer residents and farmers with small personal sections. Copes with any remnants of cultivated plants, shrubs, hard and thick grass. The power of the crumbs is sufficient to cope with hard vegetation.

Kp.05 is used on an uneven surface, since the working organ in the form of a large disk is easily adjusted to any irregularities. Not afraid of a mower of small stones and branches. Around the disk is a metal casing that protects the operator from small particles of stones and vegetation.

Characteristics of the KP-05 for the Neva walk-behind engineer MB-1 and MB-2 and the price in the table:

TC KP-05 Indicators
Performance 0.15 ha/hour
Maximum velocity speed during operation 2-4 km/h
The width of the capture 560 mm
The speed of rotation of the working bodies 2300-2500 vol./min.
Maximum height of mowing grass 100 cm
The weight of technology 30 kg
The price of the official model 14 500

Homemade constructions

Given that there are several varieties of braids, we give several options for homemade structures. Let’s start with a simpler rotor option.

Rotor haymaking is used to mow high herbs. Small shoots such a model do not mow, but grinds. You will need two discs to make such a model. These will be rotors on which the cutting elements are fixed.

Homemade mowing equipment for a walk.behind tractor

For rotors, it is better to use hardened metal disks. Four knives are installed on each rotor. Keep in mind that the knives should rotate around its axis 360 degrees. Therefore, calculate the ratio of fasteners in the rotor and the length of the cutting elements.

Knives are attached to the discs by means of shinka. The distance from the plane of the knife to Shinka should be slightly larger than the thickness of the cutting element. This scheme will provide knives with free rotation due to centrifugal force, and prevent mechanical damage to the elements in a collision with a solid subject.

Rotors are attached to shafts made of high.carbon steel. The shafts themselves are installed on the welded frame, and are aggregated to the walk.behind tractor by means of a power selection shaft. Keep in mind that the rotors should rotate to meet one another, this will allow you to form a bracket in the rolls.

Homemade segment mowing is made somewhat more complicated. You will need a metal bar, about 120 centimeters long. Here, at equal distances, you need to drill holes for fasteners.

By means of threaded connections, a guide rail (length 90 cm) and knives are installed. The cutting elements are installed in two.sided, on both sides of the bar. Powers and fixators are installed on the basis. The braid operates from the engine of the walk.behind tractor, the force is transmitted through the power shaft.

motor, block, adapter, price

Please note that mowers, homemade or factory ones need to be able to connect to the walk.behind tractor. This is done like this:

  • The same.based tractor switches to reverse mode.
  • Before connecting the selection shaft, the docking unit is installed in the clutch connector.
  • After installing VOM, the clutch is fixed with a shkworm equipped. Keep in mind that the presence of a spring must not withstand the loads otherwise.

Please note that the wheel pairs of motoblocks have weighting elements that provide reliable adhesion when cultivating land. Speasing the grass, cargo can be removed, this will remove the load from the engine, accordingly the performance will increase

Keep in mind that in the manufacture of a rotary mower you need to install protective covers

Speasing the grass, cargo can be removed, this will remove the load from the engine, accordingly the performance will increase. Keep in mind that in the manufacture of a rotary mower you need to install protective covers.

In which case it makes sense to purchase a motor.cultivator, and in which one is a single tractor?

The first unit is intended only for cultivating the Earth using milling. And although some models allow the use of other nozzles, nevertheless, these nozzles are designed only for soil processing, and, in addition, due to the small weight of the motor-cultivator, perform serious earthworks to them tiring for the operator.

motor, block, adapter, price

Motoblocks- units with a wide spectrum of attachment equipment: plow, cummen, cultivator, snowman, brush, hay and lawn mower, trailer, etc. That is, they serve to solve a wide variety of problems during the round year. They are heavier and more powerful than motor cultivators, so they are better suited for plowing virgin lands and other earthwork work.

What kind of hinged equipment that is not related to the cultivation of land can be purchased? There are nozzles for cutting grass. segment (frontal) or rotary hayfields.

Segment. a traditional solution, they are two canvases with sharpened teeth, one of which has its own drive (the design resembles a hair cutter). Rotor mowing vegetation due to two cutting discs mounted on the frame. These discs are “floating”, due to which the rotary mowers are more reliable than segmented ones: having run into an obstacle, the discs do not break (like teeth), but go around it. In addition, unlike a segment mower, the rotor lays cut grass in a row, and in order to remove it, additional gratulation is not required.

Note that a single.axic tractor with a haying.mobble of any type cannot act as a lawn mower, since even a slight slipping of its wheel with a directed tread can lead to damage to the lawn. But such an aggregate copes with a rough vegetation of high yields and can be used to mow cereal crops and even a stunted shrub.

When the unoic tractor is not used for a long time, you should drain the fuel from the engine: over time, gasoline loses its properties, and if this is not done, when starting, the engine will stall or work with interruptions

Among the hinged tools for motor blocks are snow clearing devices: a shovel (dump), as well as a special snowball player with a screw mechanism that captures snow and throws it to a distance of up to 10 m through the bell. As a rule, the width of the snow chip is about 70 cm, the performance of the unit is 2500 m²/h. For cleaning freshly fallen snow up to 10 cm deep, as well as for cleaning the territory of garbage, another nozzle is provided. a brush 80–100 cm wide.

Finally, the accessory that is important for many consumers is a cart (trailer) with a carrying capacity of an average of 300-350 kg, which allows you to transport various goods. The speed of movement of the machine with a cart is 10-11 km/h.

Such is the nomenclature of additional accessories to most models of motoblocks. However, for units designed for professional use, other nozzles are also provided. So, for some models, you can find a shredder of branches, a hay heapon, a special mill, with the help of which you can prepare even a rocky target for planting a lawn in one pass, and others.

One of the advantages of motoblocks is a large weight, from 70 to 170 kg with a nozzle, so that the load on the hands, shoulders and back of the operator is less than when working with a motor.cultivator. However, this advantage can be considered as a drawback, when there is a need to transport the car from one place to another. However, 70-kilogram motor blocks in assembled form are quite compact (all models are removable or folding handles), so they can be transported even on cars.

Роторная косилка своими руками- 2. Homemade rotary mower 2.

Differences between motoblocks

Power of the motor blocks. 6–9 liters.With. (only in individual models of heavy class. up to 12 liters.With.). The difference is insignificant and fundamentally does not affect the performance of the unit. But it affects its durability: the more powerful the engine of the machine, the longer it will last. Mostally, gasoline 4-stroke engines operating on AI-92 gasoline (only some models of heavy units-diesel) are installed on motor blocks.

The main part of the motoblocks presented on the market of both foreign and domestic production is equipped with 4-stroke internal combustion engines with a large motor resource from three manufacturers-Briggs Stratton (USA), Robin-Subaru and Honda (Japan). over, when buying units of many companies, you can choose the power and brand of the engine.

All modern motoblock models are installed not with lateral, but with the upper location of the valves, which work quieter and less vibration. Gasoline consumption depends on the operation of the device, but on average it is 1.5–2 l/h. The fundamental difference between the units is in the type of attachment drive: it is belt or gear, and the latter with a power selection shaft. Almost everyone and a number of foreign motoblocks have a first type of drive. However, according to experts, it is not very reliable: with high operational loads, the belt can slip and even break.

The service life of the walk.behind tractor depends on the features of its operation, moreover, the qualitative engines have an operating time before the first refusal. at least 800–1500 mothers

The design with a power selection shaft is more reliable, and in addition, attaching nozzles to the shaft is easier and faster than to the belt drive (you can change the nozzle on the motor blocks of some models in a couple of minutes). Another advantage of the mechanism with a shaft. it allows you to hang on the car a cutter behind (from the operator), and not instead of wheels, as in units with a belt drive. over, the cutters of a number of manufacturers rotate in the direction of rotation of the wheels, thereby simplifying the process of burrowing the cutter into the ground and reducing the load on the back and shoulders of the user. Meanwhile, some experts argue that in practice, motoblocks with a belt drive in one pass plow the ground to a greater depth than units with a shaft. Among the differences between the walk.behind tracts. the number of speeds: minimum. one forward and one back, as much as possible. five forward and two back. Typically, the handles of machines can be adjusted in height, and sometimes also in the corner of rotation in the horizontal plane.

| Denial of responsibility | Contacts |RSS