Replacement of a spray on a trimmer Hitachi. How to remove a fishing line for a trimmer from a trimmer for grass

Criteria for choosing discs for trimmers for grass and instructions for replacing them

If the disk on the trimmer is used regularly, it needs to be removed from time to time to remove and sharpen or change it to a new. This part can be made of metal or plastic, have a different number of blades, but the replacement process remains the same. over, this procedure is similar to the equipment of different manufacturers, whether Carver or Huter, but minor differences are possible. Changing the knife on the trimmer is quite simple if you observe safety precautions and know the correct procedure for which you can find a description of which you can in the user’s instructions. The whole process of replacing step by step, as well as the way of independent sharpening of knives, will be described in this material.

A trimmer for grass with a knife installed on it is most conveniently used for a more comfortable mowing of high and loaded grass in the country. a fishing line for a trimmer on a motorcycle in such cases does not cope. Thin torn very quickly. Using Tolstoy 2.3 mm cord or homemade rods with cables forces the vegetation to wind up on the rogue. This increases the load on the engine. As a result, the piston group and other mobile units of the unit wear out very quickly.

If the mowing of a weeds is produced by an electric trimmer without a knife, only with a fishing line, even a thick with a figure section, the problem cannot be solved. There is always a risk of overheating the electric motor and disable flexible shaft. And it’s all in a large torque of the electric motor. The grass wound on a spindle creates strong resistance to the shaft resembling a speedometer cable that does not withstand and twist.

In order to protect the equipment from premature wear, manufacturers have provided the ability to install special knives on the grass for grass for grass. The design and shape of existing cutting elements allows you to easily cope not only with coarse and outgrown with grass, but also to successfully fight the young shrub.

Choosing the best option for a cutting knife for a lawn mower

Some manufacturers of trimmers with a rigid structure of the gear rampart equip their tools additionally not only fishing lines, but also with steel disks. This does not always happen, and if such a situation is appropriate, then if necessary, instead of a mowing head with a fishing line, a metal disk is installed. However, this does not always happen. First you need to make sure that a steel disk can be used on a trimmer. Consider all types, and designs manufactured for trimmers of cutting knives.

It is interesting! The size of the landing hole on all metal disks is 25.4 mm or 1 inch. Models with a large diameter are rare, and for their use you will need to use the adapter.

What can be used instead of fishing line

Many users of trimmers are wondering: how to replace the cord, by default used in this kind of devices? Unsafe experiments begin to carry out, installing metal or copper wire, metal cables or strings in a mowing head, as well as a regular fishing fishing line for a trimmer.

If you install a metal cable instead of fishing line, then a trimmer for grass turns into a dangerous device not only for the user, but also for others. This fact is explained by the fact that during the operation of the unit, the steel cable will be gradually shut up, its ends are gradually released, and small pieces of wire will fly in different directions at high speed.

A similar one happens when using steel or copper wire, only with the difference that the torn pieces will be larger and can cause a significant injury.

And if you accidentally hook your or someone’s leg, working as an unit with a steel cable (wire), then a strong and deep section of the fabrics, and in some cases, amputation of the fingers are provided with you. The manufacturer is not in vain for these purposes, nylon uses, since it is quite light and durable, and when separating he does not fly away and cannot cause injury.

It is possible to use a fishing fishing line for a trimmer in a trimmer instead of a standard one, of course, but this will add unnecessary trouble, because it quickly wears out, breaks, mows slowly and does not fit for cutting hard grass. In addition, during the work, a lot of time is lost to replace the broken tool more than once.

In practice, the installation of a regular fishing line is justified if the user is going to mow grass near the fence, especially if he is from a rabid grid. In this case, in order to protect the standard and sometimes expensive cord from wear, it changes to a fishing fishing line for a trimmer, which is not a pity. Usually, in order to change the cord to a fishing line for a trimmer, it must be selected the greatest thickness-2-3 mm.

Malfunctions and their elimination

Electric and gasoline trimmers have typical breakdowns and malfunctions. For devices running from an internal combustion engine, this is:

  • problems in the carburetor;
  • engine breakdown;
  • problems with the fuel system;
  • breakdown of the gearbox, starter, muffler;
  • blockages;
  • Air filter breakdown;
  • Problems with ignition coil.

Electric units have specific breakdowns:

With simple problems, you can make a trimmer repair for grass with your own hands.

Why is a trimmer not starting for grass

The most common reason that the unit does not start is the use of poor.quality fuel. The choice of gas stamps below AI-92 can disable the lawnical mower. If high.quality fuel is used, you need to look for other reasons. To do this, carefully check all nodes and systems. The checks are subject to:

The device may not start after prolonged downtime. Before turning on a trimmer for grass, you need to study well the instructions for operation. The solution of many problems is indicated in it.

If it stalls when you press the gas

There are several reasons why a trimmer for grass stalls when gas is pressed:

  • The first reason is the dumping of the carburetor.
  • Fuel valve.
  • Fur valve blockage.
  • The weakening and sagging of the carburetor cable or sagging of the fuel intake hose.

So that the described problems with the lawn mower do not arise, you need to carefully monitor the condition of the device and its blocks. Timely cleaning, washing of the unit and spare parts allow you to increase its life.

Starter breakdowns

The most difficult breakdown of the starter occurs when the rope is broken and winding it into the flywheel of the operating engine. As a result, the spring may burst and the pulley plunges. In this case, only a complete replacement of the spare part will help. This breakdown rarely occurs. often:

In this case, it is easy to fix the starter yourself. The manufacturer has prepared a step.by.step instruction for this.

REDUTOR Repair

Caring for the motorcade gearbox consists in the timely lubrication of the unit. The absence of one can lead to rapid wear of the gear and jamming of the gearbox module.

The main malfunctions of the trimmer gearbox for grass:

  • severe heating of the gear component due to the use of low-quality lubrication or its absence;
  • shaking of the shaft during the rotation of worn bearings;
  • staggering or flowering from the bar of the gear ratio as a result of damage to the case;
  • Lack of rotation of the output shaft with a knife due to wear on the teeth on the gears.

This happens due to the use of low-quality lubrication or its complete absence. Another reason for the failure of the gearbox is the operation of a trimmer for grass at the limit of its capabilities and the hit of foreign objects. To replace a faulty bearing, a gearbox is disassembled.

Features of the repair of electric models

Electric models of trimmers operating from the network have several main blocks:

replacement, spray, trimmer, hitachi, remove, fishing

Each electrimmer block has specific problems. In the mechanical part, they depend on the presence of a fishing line used as a cutting element. Reasons for the termination of work:

You can identify the problems of the electrical part of the electrocos using special tools:

To eliminate problems, a soldering lamp is needed.

  • a malfunction of the power cable;
  • problems with an outlet and fork;
  • the failure of the control handle;
  • combustion of the starter winding, engine replacement is required;
  • Contact breaks can be corrected independently using a soldering lamp.

The choice of fishing line

In order for the dressing of the fishing line to the trimmer head to be successful, it is important not to fail to choose the consumer material. The thicker the cord you refuel, the more thick and hard grass it can cut

A universal fishing line for a trimmer is often used, the diameter of which is 2 mm. You can choose the diameter suitable for the mower in the following ways:

See the information about the thickness of the fishing line in the instructions attached to the trimmer. Pay attention to the squash itself. Sometimes information is applied on it about possible fishing line diameters. Another option is to try to insert the cord into the output

If it easily passes into it, then the selected fishing diameter is suitable for use.

A coil for a trimmer for grass can choose a cord thread by type of engine. If the fishing line for the trimmer is too thick, then the resistance to rotation will increase. the engine in this case will overheat and will soon fail. Useful recommendations:

  • For an electric device with an engine of less than 500 in, a thread of 1.3 mm thick is suitable. If this was not found, then you can use a fishing line for a trimmer by 1.6 mm. If the power is more than 1 kW, then select a cord with a diameter of 2 mm.
  • The gasoline trimmer for grass has a shaft mower. For the bent version, the cord for 2 mm is often used. If the shaft is straight, then set the thread 2.4–2.5 or 3 mm. The thickest fishing line for a trimmer is installed on powerful devices. from 1.3 kW.

Pay attention to the type of cross section of the cordry thread. Some popular options:

  • The most common fishing lines with a round section. They mow fresh herbs well, but they cope worse with shrubs, drows.
  • Twisted (spiral) cord does not differ in high strength, but well suitable for thin young grass.
  • The jagged thread with sharp edges is ideal for a large weeds in a neglected area.
  • You can mow the lawn in a rectangular, starry or square fishing line for a trimmer for grass, but they are not very durable.
  • The most durable is a two.component cord with an internal core and a round section.

Types of fishing line for a trimmer for grass, keep in mind that it is impossible to use wire, metal strings and cables, as well as an ordinary fishing thread instead. The device will be dangerous for both the user and for others. So the cable or similar products will gradually begin to shut down, as a result, their ends will be reacted, and small pieces will scatter at high speed.

Ignition algorithm

The ignition on the trimmer is easily adjustable.

  • Remove the cover from the engine by unscrewing all the bolts holding it. For example, on the Patriot (Patriot) PT 2540 gasoline scrap, you need to unscrew the air filter housing and remove it from the latches using a screwdriver with a flat sting. After that, the plastic case can be easily removed.

With the help of a screwdriver, weaken 2 bolts (do not unscrew completely), holding the magnet. Turn the flywheel so that the magnets are from above. Further, to correctly install the best gap between the flywheel and the coil, you can use a regular business card or calendar. If you do not have it at hand, you can use a sheet of A4 paper to fold the ignition by folding it 2 times (as a result you will get a thickness of 4 sheets). This thickness will be sufficient to obtain the optimal clearance and adjust the ignition. Insert a business card or paper between the coil and magnets. The magnetic field will pull the coil to the flywheel. Holding the magnet with your fingers in this position, tighten the fasteners. Delete the business card. After that, the ignition on the trimmer will be adjusted.

Replacing Magneto

To correctly purchase Magneto for replacement, you need to contact a specialized store or service center and name the brand and model of a trimmer for grass.

To remove the magneto, you need to remove the plastic casing from the trimmer for the grass. On different models of motorcycle, this process is different. It is usually necessary to unscrew the bolts, but on some benzotrimers it may be necessary to squeeze the latches. After that, access to the coil opens. To remove the part, you need to unscrew the holding fasteners and disconnect the wires.

When installing a new part, you need to correctly set the distance between the flywheel and magneto. To do this, you need to turn the flywheel with magnets up, install the coil and fix it, but the screws do not completely tighten, so that there is a short distance between the details. Further, between the coil and the flywheel, it is necessary to put a calendar, a business card or four.folded paper sheet of A4 format, you can also use a plastic strip cut out of the bottle. Such tricks will provide a suitable gap between the flywheel and magneto. A more competent solution will be the use of a special template, but it is impractical to purchase it for the sake of once. Next, you need to tighten the fasteners, remove the object between the details, and, holding the magneto with your hands so that it does not spin, tightly tighten the fixing screws. After that, you should crank the flywheel and make sure that it does not catch the coil anywhere. Now you need to connect the wires and insert the candle into the cap, and then check the operation of the device.

How to refuel a fishing line for a trimmer to a trimmer coil for grass? Instructions

Warranty production of the factory refueling of a trimmer for the grass will be in demand for fishing line substitutions. Having a very approximate idea of ​​how to tuck a fishing line for a trimmer to the coil of a trimmer for grass without the help of others, the new ones without hunting take up this matter. But with some ability, mastering this simple teaching does not represent any difficulties, and the similar annotation presented below will greatly facilitate this process.

How to wind a fishing line for a trimmer to a mowing head of a trimmer for grass or motorcycle

Fishing line in a trimmer for grass: 2 ordinary methods

For us, the turnover with our readers is very fundamental. Leave your own rating in the Комментарии и мнения владельцев with the argument of your choice. Your worldview is useful to other users.

Two segments

The only difference from the method is no different from the method. Two wound segments of fishing line, accommodated 1st.

There are two special fixing nests on the coil (see sketch above).

They hook it previously formed on the fishing line, and begin to wrap a fishing line for a trimmer.

Winding is carried out in a special way

The winding must be carried out in the future: at first the lower fishing line for the trimmer, t.E. That which is closer to the holes on the day of the coil, and only later the upper one, t.E. The one that will overlap the lower section.

The tip is made in the holes of the corps of the rogue trimmer for the grass. They are pulled to clicks, Yaki means that the fishing line for the trimmer has left the latch.

The tip is threaded into the holes of the corps of the rogue trimmer for the grass

The coil is fastened into the case. The fishing line for a trimmer in a spool is replaced.

Trimmer head with two Usik

After extracting the spray from the coil body, we determine the number of streams for winding fishing line (1 or 2). There are no distinctions between bobs with one and 2 grooves, but with a negligent refueling in a paired groove, there are difficulties with operation. Due to the likelihood of interweaving with the adjacent tool, a situation may appear when, after the wear of the workers’ antennae, it is unrealistic to extract new.

Regardless of the number of streams for refueling, a fishing line is taken for a trimmer from 1 length.5 to 3 meters. The winding needs to be created in a flip rotation of the head to the side, because the winding in the direction of movement will lead to the fact that the fishing line for the trimmer will not be removed from the bobbin. After the fishing line for the trimmer, tucked in the coil of the trimmer for the grass, free ends (15-30 cm) extending into special holes. Next, collect the head in the back of the order and check the performance. Do not worry if the ends of the 2nd antenpers are very different in size, since when the trimmer for the grass is launched, the knife installed on protection will cut off excess.

How to install a starter on MTZ

How to install a starter on MTZ instead of starting installation without changes? The role of the starting installation is played by a button or hole into which you need to insert the ignition key. The performance of such a starting device is low, so a change in the mechanism to a toothed starter is established. The need for such an update is associated with such characteristics of the gearbox:

  • Are produced as planetary gearboxes with 1 or more of 2 gears
  • The voltage passes through the gearbox, increases several times.
  • He has a low level of electricity consumption, especially if you start the device on a cold engine.
  • Automatic shutdown occurs immediately after starting the main engine.
  • Most often, the reason that you need to replace the starting installation with a starter is the need to repair or change the starting mechanism to a more powerful. The processed design is as good as the original.

The following characteristics belong to the factors because of which it is necessary to re-equip the MTZ:

  • Starter Starter MTZ does not return the starter well.
  • The trigger slowly rotates the turnover of the crankshaft after its hook. This is often due to the fact that the battery is not sufficiently charged, irregular oil for filling or the position of contact brushes is used.
  • The mechanism does not turn off when the engine is already turned on.
  • The installation simply failed, so it does not respond to launch.
  • Clutch of the bendix and flywheel does not occur.
  • There is no rotation of the crankshaft during the rotation of the reinforcement.

In one case or another, the owner must either change the starting installation for the starter, or repair it.

Removing and disassembling the starter, replacing broken parts

To repair the starter of the trimmer for the grass, it first needs to be disassembled, and then collect it. This process is not particularly complicated. You will need to work the shape of the screwdriver.

Everything should be done carefully, observing precautions, especially so that the spring does not injure the owner in case of accidental departure

Starting analysis

Disassemble the starter mechanism to install new parts instead of broken in the following sequence:

Unscrew the screw that attaches the pulley with the starter lid using a screwdriver; Remove the spring and antennae; Carefully remove the pulley (you need to turn your head or work, after putting on your glasses and gloves); Determine why the trigger worked; If the spring fell apart almost completely, it is replaced; Когда пружина выходит из крючка, она устанавливается на прежнее место, предварительно сгибая антенну (фотографии показывают процесс установки);

After the spring plate is installed inside the groove, carefully tighten it. To change the spring, the work must be performed carefully and accurately: it can accidentally explode under the influence of the force caused by its bringing into effect

Even if you carefully delete the video, the spring tape is very quickly torn off the coil and can injure the hand with sharp edges

To change the spring, the work must be performed carefully and accurately: it can accidentally explode under the influence of the force caused by its bringing into effect. Even if you carefully delete the video, the spring tape is very quickly torn off the coil and can injure the hand with sharp edges.

Immediately put in place a spring plate does not always work. This often slips, so attempts should be repeated to achieve the desired result.

Starter assembly

The assembly of the starting installation is carried out in several stages:

The coil turns over, installing it so that the bend of the spring accurately fits into the groove of the case, as in the photo below;

When making the above manipulations, it is necessary to put two goals. If this is not done, the spring will ultimately damage the plastic cup, and when it is removed, jamming will begin. This makes you feel that spring has come. To eliminate this drawback, it is necessary to install this part of a larger length or an additional goal.

When such details are not enough, you can just unscrew the screw a little, and the starter assembly will start working without fixing. But this option is temporary. It is better to repair it as soon as possible.

Spring tension

After installing the spring, tighten it. To do this, follow the following actions:

  • Remove the handle from the starter cord;
  • Then the rope is inserted into the groove of the coil;
  • The spring is delayed by the rotation of the turn in the opposite direction clockwise (winding);
  • Make the required number of revolutions specified in the operating instructions for the used trimmer model for grass, and the corresponding length of the cord used;
  • At the very end, the rope is lowered into the hole provided for this, located in the starter cover;
  • Place the handle in place by fixing it with a node.

Read what gasoline is pouring into the Husqvarna lawn mower

If after the repair the spring continues to fly, you can get rid of it in the following ways:

  • Insert the corresponding piece of the plate into the groove at the location of the spring hook;
  • Drill holes on both sides of the groove in the coil, into which you need to insert a spring hook and fix it with wire.

Replacing a torn cord

A torn cable is replaced in the following sequence:

  • The old cord is removed;
  • Choose a rope of a suitable size (thickness and length);
  • Having passed it through a special hole located in the coil, tie a knot;
  • Spring valve producing the required number of revolutions;
  • Fix the pen

Hitachi Trimmer 7 Year Review CG22EAS(SLP)

It is better to tighten the spring plate with Partner so that the edge of the cord does not twist inside the starter mechanism.

It is not difficult to assemble a starter on a trimmer and wound a spring, but this must be done carefully and carefully. For different models of gasoline engines, the breakdown of the starting mechanisms are the same, so they are repaired the same

However, there are some nuances associated with their constructive features.

Review: Trimmer head Hitachi 781301. A little expensive for the consumable, but performed qualitatively.

Greetings to you, friends.It seems that I found a suitable head for my Hammer trimmer amazing thing: heads for trimmers in specialized and not very stores in bulk, but I was managed to buy such a unique model of a trimmer for grass, which only my native, extremely poorly made for it, is suitable for it. And I found one more from a third.party, but very good manufacturer. True, its price is like a quarter of the trimmer itself for grass, but there is nowhere to go.

The main parameters are indicated on the front side of the package.REAL thread M8 and a nut 1.25, almost not recessed into the case designed for wrapping on a short screw of the reducer gearbox. So I managed to buy such a trimmer for the grass)

Back on the package brief instructions for the use and maintenance of the coil.

Hitachi trimmer head plastic, unlike native Hammer, very thick and high.quality.

The head is semi.automatic, the fishing line for the trimmer is extended a few centimeters with a light blow by the button on the ground.

Brassy inserts in the slots of the case protect the body from cuts with fishing line.

The nut is also metal, however, like all heads.

The head is disassembled somewhat more complicated than this is described in the instructions.Theoretically, it can be disassembled by pressing the hollows with your fingers on the case, but I could not do it. I had to help myself with a wide screwdriver, sticking it into the upper slots and bent the clamps. Then it can be developed, but it is unlikely that it will most likely be scorched by grass and it will become even more difficult to open it.

The coil spring is quite strong, and if the line for the trimmer is over, be more careful: when opening you can get a reel in the forehead!Having removed the lid we get the result:

The lower part of the body of the head is disassembled. Compared to the native Hammerov. day and night.

The fishing line for the trimmer is wound clockwise two layers.

The spring is powerful, installed in only one position, a wider part down, if you confuse, then the lid will not close.

Before installing the ends of the fishing line, it is better to first insert into the grooves on the coil housing, and only then shove them into the holes on the case, and then press with force. You can do it, but it’s more convenient.

The fishing line for the trimmer is suitable only for verification, although it is thick, it will be quickly rubbed and consumed. Personally, I prefer a twisted fishing line for a trimmer, but so far it comes down and my native.

Review: trimmer head Huter. One of the serious ambush of trimmers Huter.

A semi-automatic head with a fishing line for trimmers Huter Eth-1200 is supplied with a 2mm thick with a thick-colored fishing line of 5m.Height of the head 320g.The head has a bobbin with a fishing line and two metal holes through which the ends of this fishing line are removed that carry out the mowing of the grass during the rapid rotation of the head of the trimmer for the grass.Designed for electric trimmers Huter Get-1200SL.

When the grass is spent, the ends of the fishing line wear out and their length decreases.Therefore, the radius of the capture of the mowing becomes less.You can restore the length of the ends of the fishing line with a slight blow to the ground of the button located in the center of the head, when the head of the trimmer for grass is gaining momentum.

replacement, spray, trimmer, hitachi, remove, fishing

After that, the two ends of the fishing line will supply, the excess of which will be cut off when the trimmer for the grass rotates for the grass.

Sooner or later, one of the cutting ends under the root breaks out at the fishing line and it is necessary to re.dispatch it, or the fishing line for the trimmer ends and it is necessary to wind up a new one.

In short, it becomes necessary to remove the head cover and pull out the bobbin bobbin from the housing.The most interesting begins here.A similar situation is described in the fable of Ivan Andreevich Krylov “Monkey and glasses” 🙂

The fact is that the trimmer head Huter has a unique design.I have never met any company.Open it for reloading fishing line is not for the faint of heart.

Description of how to do this is missing.The inscription on the back of the head of the head in English “click to open” did not help.Pressed, tried to turn the body in both directions.Nothing helped.

Finally realizing that my brains were not enough for the first non.destructive opening, he reconciled with this and began to look for knowledgeable people.The cheerful and friendly saleswoman in my village store for the sale of power tools and devices for them helped. Antonina, showing how this is done. Thanks to her for that!

Over time, I, of course, forgot this unique experience.To bow again to Antonin was already inconvenient.I had to turn on the brain, and it is objectively and in detail to deal with the problem.The Internet was prompted by the method of uprooting the head of the head head of the head.Which did not suit at all.

From the video found, the head device understood.It turned out that the lid is held on four holders attached in the nests of the body and is fixed with a latch.Having squeezed which the corresponding screwdriver with a flat blade and turning the body clockwise, you can easily remove the lid and pull out the bobbin with the remains of the fishing line.

Fishing line refueling is standard and described in detail in the description of a trimmer for grass.Also not simple, but you can figure it out.

When using the head for a sufficiently long time, a little earth, the remains of grass and all dirt are packed into it.For the benefit of the case, I cleaned the dirt from the body and the outer parts of the head.

The head is not difficult to assemble.Necessary:- Title the ends of the fishing line into the corresponding holes of the case:

In the photo, among other things, on the bobbin you can see slits for fastening fishing line sizes from 1.6 to 2.6mm. For electric trimmers, Huter Get-1200S is recommended a fishing line for a trimmer with a diameter of 2mm, which is reliably fixed in the slots for fishing line 2.4mm.

Next:- Combine holders with the corresponding slots in the hull cover. with a simple press on the back of the case with an inserted bobbin with a fishing line. click the latch. turn the body counterclockwise.

I received great satisfaction after it was finally able to remove the lid of the head :)) The feeling of victory over the rebellious and hostile to you nature 🙂 as a taming of Claudt’s horses on the Anichka bridge of St. Petersburg.

Buy or not such a head for trimmers?Only if there is a desire to fight her when replacing a fishing line.In addition, the weight of this head is 15g above the weight of a similar head from Patriot trimmers.How important is it. I don’t know.

The plastic is ordinary, I haven’t scattered yet.But, people complain of its fragility. With careless attacks on the ground, it can be crumbled.

In fact, the thread in the head is standard left m10x1.25 LH.Accordingly, the head for fishing line with a diameter of 2mm can be used standard with the same thread, for example, from a trimmer for Patriot grass.

Offers at different of different manufacturers in the market enough.From the most democratic to completely prohibitive for automatic heads.You can choose the most suitable for you.

The final moment of the instruction

Typically, the process of replacing fishing line on a trimmer of a particular model is popularly described by accompanying documentation. Another question is that this documentation is often supplied in a foreign language, since the notorious lawn mowers for the most part are imported products.

Meanwhile, there is a much simpler, more economical and healthy way for human health and nature. putting the lawns of an ordinary peasant oblique in order. Blory of braids for grass:

which is subsequently accompanied by abundantly growing greens, and not by the formation of dryness as a result of the work of a trimmer for grass.

Trimmer Head Removal

Winding profiles (cones)

Different models of coils of the coils of fishing line on the rogue are applied in different ways. High.quality products use a cylindrical and conical winding method. The laid fishing line for a trimmer to profile forms a flat fishing line for a trimmer. With a cylindrical winding, this fishing line for a trimmer is straight, parallel to the spool, with conical. inclined.

The straight conical shape narrows to the front side of the spool, the opposite. expands. Straight cone reduces the friction of the fishing line. The reverse styling type reduces the likelihood of spontaneous fishing line.

There is a third type of winding. chaotic. Usually used in cheap Chinese fishing rods. And if such a winding can still be tolerated using a regular fishing line for a trimmer, then you should refuse to use in such a coil of the cord. Bad castings, “beard”, overlaps and confusion are provided. This leads to failures during fishing, and can also ruin the mood for every fisherman.

| Denial of responsibility | Contacts |RSS