Replacement of bobbin on the trimmer Stihl. Replacing fishing line in trimmer: 2 simple ways

How to remove a mowing head from a trimmer for STIHL grass

When finishing the garden, park zones and other places where you need to mow various types of plants, you often have to change the cutting tool in the trimmer. This is due to the fact that the standard cord installed in the head of the lawn mower can only work with grass. But when a shrub or a young sprout of a tree appears in the way of the worker, a fishing line for a trimmer does not cope with this task and should be replaced by a more effective cutting tool.

Trimmer manufacturers have provided similar situations and complemented their products with a mass of nozzles in the form of knives with several “petals” or in the form of disks similar to disc saws.

If you replace the fishing line for a trimmer with a knife with several “petals”, then this tool can mow both high grass and plants with thick and dry stems. And changing the fishing line for the trimmer on the disk, the user gets the ability to cut bushes or small trees.

Knives and wheels are installed according to the following algorithm.

  • First, remove it by fixing the shaft, the mowing head (turn clockwise) or a nut with a shoe if the unit has not yet been used.
  • Set a saw or cutting knife so that they are placed on a small ledge (sleeve).
  • Install the fastener on the knife and screw the nut to the shaft (counterclockwise).
  • Tighten the nut (counterclockwise) using a pipe key.

You can watch this video to better understand the process of changing the tool.

Read how to remove the bearing from the gearbox of the corner grinder

How to refuel a fishing line for a trimmer to a lawn mower: how to change and charge a reel, how to change and how much to wind it into a trimmer for grass

When spring comes, people often spend their free time in a summer cottage. They try to save their site from such a problem as weeds and grass with the onset of warm days. It is difficult to do this manually, especially if the territory is very large, so the lawn mower will help. Thanks to this technique, you can trim the grass and remove weeds. this is a suitable device to mow unnecessary plants near the fence, at home, between rows in the garden on a flower bed and so on. About how to choose a lawn mower, which is suitable for your needs, read here. The cutting element in this device is a fishing line for a trimmer (strong polyethylene thread), which is wound on a special element. a reel. But over time, the fishing line for the trimmer wears out and there is a need to replace it. The article will talk about how to refuel a fishing line for a trimmer to a lawn mower.

If there is a country plot or large land near your individual house or cottage, then for the convenience of cleaning grass and weeds, you must use the lawn mower. If you think to choose an electric lawn mower or gasoline, then click here and you will find comparative characteristics of different models.

Over time, a fishing line for a trimmer on a mower wear out and it needs to replace it. this can be done yourself. Choosing this polyethylene thread is necessary depending on the model of the mowing. It is also worth monitoring the rest of the unit details, for example, you will find information about knives for the Craftsman lawn mower, which also wear out and can lead to irreversible consequences.

The device of the coil, into which the fishing line for the trimmer is inserted, is very simple. But it differs depending on whether a coil with one or two antennae works works

It is important to observe safety precautions while replacing the fishing line in the reel

Large cord consumption

Basically, the cord quickly ends if you often knock on the ground with a semi.automatic head or press it hard. The coil unlock occurs, and the fishing line for the trimmer, lengthening, is cut off with a knife. Another reason that the cord quickly ends is the improper operation of the device with an automatic head: the user during kosbe often drops engine speed. But as we recall, the automatic head is arranged so that it is with each reduction in the revolution that a new portion of fishing line is supplied, so it is quickly consumed.

Battering trimmers options

Battery braids for grass are ordinary in use, they intensively help clear the terrain near the house from the grass. Such devices contain batteries with an indicator for a charge. You can just adjust the bar and handle.

How to rewind your Stihl trimmer equipped with the AutoCut 25-2.

  • Without noise, also wires can be taken care of lawns;
  • the best option for amateur use;
  • has a little weight and holds the balance perfectly.

The equipment is in a series, and the following enters it.

  • Rod. It can be adjusted at least at any moment. It is completely suitable for those criterion when several people use the unit, and everyone can adapt it for themselves.
  • The handle has the shape of a circle and simply tunes. She has 6 positions.
  • The mowing unit is regulated. This can be done in four positions.
  • The edge can be cut vertically. With all this, the angle can be changed to 90 degrees.

The most famous versions of the cos on batteries are spelled out below.

How to wind a fishing line for a trimmer to a trimmer coil for grass: Key points

A gasoline or electric trimmer for grass is an indispensable assistant in the arsenal of a modern summer resident or owner of their own house.

Thanks to these garden devices, you can easily bake even a large personal plot.

After acquiring this tool and performing several mowing, many people think about how to correct the fishing line for a trimmer to a trimmer coil for grass.

For an inexperienced user, the first operation to replace it will seem problematic and laborious, since the developers often do not fully reflect the instructions for replacing the fishing line in the operating manual.

Two working antennae

In this type of squelpies, you should find the number of grooves for winding the fishing line lying on the inside of the coil:

For both cases, a fishing line for a trimmer 2-3 m long is taken.

In a single.bonhean coils, the fishing line for a trimmer stretches into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in the back of the rotation of the bobbin on the bar the side inside the arrow is usually indicated the correct direction of the winding.

In the presence of fixing grooves, the ends of the fishing line are threaded into them or hold the fingers of the free hand, spread into the through hole of the outer half of the bobin, the spool is locked and attached to the bar of the trimmer product.

The difference between the winding of the fishing line in the two-to-dancing coils is that initially a line of fishing line 2-5 m long is folded in half (to determine the middle fold), and the bend loop is inserted into a special groove between the grooves. Both strains of the fishing line are wound each on their own groove, fixing antennae and assembly of the coil is similar to the option considered above with one groove.

The 1st implementation of this procedure may seem to be long and quite laborious, but over time and experience, this problem will be solved significantly more freaky and easier.

The video below will clearly show how to refuel a fishing line for a trimmer to the coil of a trimmer for the grass and correct it correctly. this operation is not a complicated one and, with some patience, will necessarily be crowned with success:

Refueling coils with a thread of various types of rods

With two.stringed automatic heads:

First you need to press the clamp until the click appears, remove the lid. Carefully turn Bobin so that she can disconnect from the holder. Extract her. Measure two segments of cutting thread of the same length

replacement, bobbin, trimmer, stihl, replacing, fishing

To make further work easier, the ends of the fishing line need to be cut off at an angle. Take one end and put in a special hole in the coil. It can also be slots, grooves, clamps, etc. Further, in the direction of the arrow, you need to wind the fishing line for the trimmer, and quite tightly and evenly. In a special ear on the coil, it is necessary to fix the end of the fishing line. The second half of the fishing line is subject to the same operation, only on the other half of the coil. Next, install the coil in the head of the trimmer for the grass. And pass the rest of the fishing line in the hole in the head. Then carefully straighten the thread and close the lid. If the fishing line for the trimmer is long, then it is better to cut off the excess. About fifteen centimeters should remain on each side.

replacement, bobbin, trimmer, stihl, replacing, fishing
  • The thread is threaded into the hole that is inside;
  • Fix the ends of the thread in grooves on the case.
  • The coil is collected and pressed by a special button;
  • After that, the fishing line for the trimmer itself begins to dangle in the right direction.

You should very carefully and carefully refill the cutting thread into the unit, because not only the purity of the garden plot depends on the correctness of its winding, but also personal safety

If the coil allows you to wind fifteen meters of thread, then you should not wind so much, there is enough ten, that is, if you fold in two layers, you get five meters each. With another capacity of the fishing line, it is worth using the same rule. In the case when an ordinary round thread is used, it is better that it is 3.3 mm with a diploma. If this is a figured fishing line for a trimmer, then its thickness should be less, for example, 3 mm. It is better to wrap both segments of the fishing line at once on the spool, and you need to start with its bending

It is important to prevent overlap in the direction of the arrow. It is also important to be able to perfectly pull the thread

There will be a thread to be pulled, it may go over. If not unit, can twist. In order not to cut your hands on the figure thread yourself, you should wind it in gloves. No need to leave the ends of the fishing line long. This can lead to its tightening.

Replacing Trimer bearing Stihl FS 38

There are situations when a trimmer user for grass notices a very frisky fishing line. With all this, he has never beaten the button on the ground for lengthening the fishing line. The prerequisite is that the fishing line for the trimmer spontaneously lengthens, cutting off a special knife on the casing of the apparatus, is the absence of a spring in a mowing head. Often, beginner users of mowers, trying to charge a fishing line for a trimmer into a coil, blurry to install a clutching spring in the head, or completely lose it when opening the lid, and in the near future, do not even suspect its existence.

Also, the fishing line for the trimmer lengthens without using the buttons if the spring weakened. If the spring check confirmed this fact, then you need to slip a few goals under it to strengthen its pressing characteristics.

The owners of the trimmers, in the main brand new, are confused, adjacent to panic, when it becomes necessary to change the cutting tool or a fishing line for a trimmer in a reel. Often, when trying to unscrew the mowing head, users simply make her unusable, not suspecting that she was unscrewed in the back. So that this does not work out, if you need to change the tool, it is recommended to study in detail a step.by.step annotation given further.

  • While fill the fishing line for the trimmer into the coil, drown out the motor motorcycus or de.energize the ethletric trimmer for the grass to avoid injuries that occur when the cutting tool is accidentally launched.
  • Unscrew the nozzle mounted on the gearbox shaft. To do this, the shaft needs to be fixed by combining holes on the puck on the axis, and inserting an iron bar there or a screwdriver there.

The ignition system of the benzo tool

  • Take a piece of plywood on a different textolite and draw a circle from him with a diane of about 14 cm.
  • Cut the disk with a jigsaw in other words.
  • Drill a hole in the center of the disk, suitable along the diameter to the gear shaft. You also need to think ahead of time before installing the disk on the shaft, put the puck on this address.
  • On the sides of the disk, you can fasten small corners as it is also called to make 1-2 holes on the return sides. They will serve for refueling their fishing line.
  • To fix the fishing line for the trimmer, in the plywood of course, screw several screws.

Such a home.made mowing nozzle is fixed on the shaft with a nut. It is impossible to tighten or unscrew the nut without fixing the shaft. To change the cord, it is necessary to release screws, stick a segment of the fishing line of the desired length and crush it and again.

Also, a mowing nozzle for fixing the fishing line on its surface is certainly made from the iron sheet. How to do this can be realized from the next video.

How to replace a fishing line for a trimmer on a STIHL motorcycle

About a year ago, the author of these lines bought the STIHL Motokos (Stihl, as they say in the common people) FS 38.

The fishing line that was in the herbs was purchased for about a year and was enough, the last remnants were torn out when a dry tree branch was not seen in the grass. This is not the point.

The fishing line for the trimmer for replacement was also bought, along with a motorcycle (trimmer). But when the question arose of how to replace it, it caused difficulties. Searches on the Internet on request how to replace a fishing line for a trimmer STIHL did not lead to an instant result. precisely, the author of these lines came across a question about replacing the fishing line, asked by the user a specialist and answer: it is impossible to explain this, contact the dealer, he will show.

Well, he went to the dealer, the dealer showed, and he (the author of this entry), having arrived home, pulled out a fishing line for a trimmer and inserted it in front of the camera again. To yourself, if you need to remember, and show others. Those who are worried about the beauty of the house or garden.

So, see how to replace a fishing line for a trimmer on a STIHL motorcycle.

Update

After publishing the video, a method was found even easier, and a new video was shot. At the end of the video, bonus advice How to quickly adjust the length of the fishing line.

How to replace a fishing line for a trimmer Stihl trimmer

Winding a fishing line for a trimmer to a coil with one osik is very easy. In such structures, depending on the brand of a trimmer for grass, from two to five meters of the cord is placed. The edge of the fishing line in the spool must be tucked into a special hole or groove, after which the string is wound in the direction opposite to the rotation of the coil during operation.

Advice! To understand which way to wrap the thread, you should look at the corps of the spool. usually marks are made on it indicating the direction of movement of the coil during operation.

After the fishing line for the trimmer is windpowed, you need to leave a small piece (15-30 cm), walk into the output of the spool and collect the head again.

Coil with one working osik

The easiest option and a simple sequence of actions:

replacement, bobbin, trimmer, stihl, replacing, fishing
  • The dimensions of the bobbin and the length of the original factory winding determine the length of the fishing line recommended for winding. 2 5 m.
  • One end of the fishing line is inserted into the fixing technological hole located inside the spool.
  • The fishing line for the trimmer is wound on the drum in reverse rotation of the spray in the trimmer product direction. as a rule, on the inside of the bobin, the arrow indicates which direction the winding is carried out.
  • A small section of the fishing line is left free to output it. it is fixed in a specialized border on the inside of the bobbin, designed to keep the winding when assembling a spool in working condition.
  • The left end of the fishing line is passed through the hole of the outer part of the bobbin.
  • Half of the bobbin are collected and put on the bar of the trimmer device.

What is needed to replace the cord

With regular use of a trimmer for grass for begging grass, the discs are blunting, but they can be sharpened and continued to operate. The fishing line for a trimmer in the coil has the ability to end, so there is a need for refueling a new one, for which you need to determine the type of head and prepare the cord of the required thickness and length.

So, the mowing head is a cylindrical body in which a bastard is placed with a fishing line. Such a part is present both on electrimmers and on gasoline braids of any brands, whether it be Bosch, Makita, Stihl or other brand. There are three types of heads depending on the method of refueling and feeding the fishing line.

  • The principle of operation of the heads of the automatic group is that they independently serve a fishing line for a trimmer, when a mowing reduces the speed of the motor. Such designs are convenient when working in large areas, but they have a shortage. a large cord consumption.
  • The heads of the semi.automatic group are easy to operate. automatic fishing is performed at maximum engine speeds. To remove the cord lock, you need to carefully tap on the ground with the tool, after which the unlocked thread extends from the coil. The cut to the required length is made with a knife fixed on the protective casing.
  • Trammers for grass with manual supply of the cord must first be turned off, and then independently pull out the fishing line for the trimmer.

On a note! The most convenient and optimal in price are semi.automatic coils with the cord.

Coils for electric and gasoline braids can be with one or two tastes of fishing line. The former are used to trim low herbal shoots, the latter. for beveling tall grass and small shrubs.

Solving possible problems with fishing line

Most of the problems associated with the fishing line are similar to different trimmers and are solved in a similar way.

Automatic winding of the fishing line on the reel

There is a variety of coils in which the automatic mechanism performs winding on its own. it is enough to correctly season the fishing line for a trimmer from the user. The fishing line for the trimmer is passed through the hole on the inside of the case, its antennae without winding are spread through the hole on the outer body, the bobbin is assembled, and when rotating the winding button for the trimmer, it is wound independently inside. It is impossible to make the winding incorrectly in such a spool: the mechanism itself will determine the correct direction, since it can only spin in one direction.

The coil does not spin

The reasons why the coil does not spin are similar to the lack of fishing line. This is the wrong or uneven winding of the string, its sticking, as well as the short ends of the cord, emerging from the holes.

Preparation for the replacement of fishing line

Before replacing the fishing line, you need to pull out, and then disassemble the head. It usually includes a casing, a spring (on some models), a bobbin with a fishing line, a lid. It is necessary to turn off the electric trimmer for the grass (or drown out gasoline) from the network, and then proceed to remove the coil. It can be recorded in two different ways: in the first case, it is necessary to completely disassemble the head, and in the second. just remove the gearbox from the shaft, to which it is attached.

  • Find the latches on both sides, press and remove the lid to open the internal device of the head;
  • A bobbin is located under the lid, it must be carefully pulled out of the case (sometimes a spring is hidden under it, it should also be carefully removed to the side so as not to lose);
  • After removing the spool, it becomes noticeable in the center of the case with a fixing bolt (or screw), which must be unscrewed in a direction opposite to the clockwise movement;
  • After removing the fasteners, it is necessary to hold the body with a swaying movement to remove the coil from the gear shaft.

The second method involves the following actions. Coil head is worn on the gear shaft. To disconnect it, you need to lock this shaft. Typically, in braids, for example, the brand “Champion” or “Stihl”, for this a hole is made into which a nail, rod or screwdriver is inserted. After fixing the shaft in a fixed position, you need to, holding the body, start rotating the head clockwise, since the thread on the shaft is usually applied to the left.

Now that the head is removed and dismantled, it is necessary to determine what thickness the cord should be. You can find out the suitable diameter for your trimmer for the grass by looking at the user’s guide or on the squash itself, it usually indicates such information. Another way is to insert the thread into the hole from which it is served. If the Sruna is without difficulty, it can be used to work.

What is needed to replace the cord

With the constant use of a trimmer for grass for grass, the discs are blunting, but they can be sharpened and continued to work. Lines for a trimmer

The coil tends to end, therefore there is a need to refuel the latest, why you need to find the type of head and prepare the cord of the desired thickness and length.

So, the mowing head is a cylindrical case, in which the rogue and a fishing line are located for a trimmer. Such a part is located both on electronic trimmers and on gasoline braids of all brands, whether it be Bosch, Makita, Stihl or another brand. There are three types of heads depending on the method of refueling and feeding the fishing line.

  • The mechanism of operation of the heads of the automatic group is that without the help of others they feed a fishing line for a trimmer, when the mower reduces the speed of the motor. Such designs are comfortable when working in huge areas, but have a defect. Large cord consumption.
  • Automatic group heads are comfortable in operation. Automatic fishing is carried out at the highest revolutions of the motor. To remove clogging of the cord, carefully tap on the ground with the inventory, after which the unlocked thread will push out of the reel. The segment to the desired length is made by a knife attached to the protective cover.
  • Trammers for grass with manual supply of the cord must first be turned off, and then without the help of others remove the fishing line for the trimmer.

Coils for electronic and gasoline binders can be with one or 2 threads. The 1st is used for haircuts of low grass, 2. for cutting the highest grass and small shrubs.

Trimmer coil device for grass

Cassyle heads for trimmers come in different designs. both simple and complex. The figure below shows a semi.automatic trimmer head from the Husqvarna motorcycle (Husqvarna).

This type of head is present in the configuration of most benzocosyles and electrimmers such as Stihl (Stihl), Patriot (Patriot), Champion (Champion), Bosch (Bosch), Huter (Huter) and others. The device of the braid head is quite simple. It includes the following details:

  • the base of the mowing head;
  • button for semi.automatic supply of the cord;
  • Spulk (coil), into which a fishing line for a trimmer is refuel;
  • spring;
  • eyes. through them a fishing line for a trimmer goes outside;
  • trimmer head cover;
  • Trimmer fishing line (cord).

Why you need to put a knife on a trimmer for grass

A trimmer for grass with a knife installed on it is most conveniently used for a more comfortable mowing of high and loaded grass in the country. a fishing line for a trimmer on a motorcycle in such cases does not cope. Thin torn very quickly. Using Tolstoy 2.3 mm cord or homemade rods with cables forces the vegetation to wind up on the rogue. This increases the load on the engine. As a result, the piston group and other mobile units of the unit wear out very quickly.

If the mowing of a weeds is produced by an electric trimmer without a knife, only with a fishing line, even a thick with a figure section, the problem cannot be solved. There is always a risk of overheating the electric motor and disable flexible shaft. And it’s all in a large torque of the electric motor. The grass wound on a spindle creates strong resistance to the shaft resembling a speedometer cable that does not withstand and twist.

In order to protect the equipment from premature wear, manufacturers have provided the ability to install special knives on the grass for grass for grass. The design and shape of existing cutting elements allows you to easily cope not only with coarse and outgrown with grass, but also to successfully fight the young shrub.

Which fishing line for a trimmer to choose to refuel a lawn mower

The thickness of the polyethylene thread depends on the model of the technique and varies from 1.2 to 4 mm. She may be:

  • With a round section. this is the most durable material for mowing herbaceous plants;
  • with curly section. used to mow soft plants;
  • twisted. used for thin grass;
  • professional type, is not suitable for all models of technology.

To change the fishing line for a trimmer on a lawn mower, it is necessary to purchase a cutting thread that will be ideal for a particular type of mower.

Read where is the fuel filter in the trimmer Sturm

How to Release Trimmer Line

You can soak the thread in a basin of water for several minutes to increase elasticity and strength.

How to remove a coil from a trimmer for STIHL grass

Trimmer for grass, whether it is gasoline or electronic, is the only right solution for mowing grass in inaccessible places with which the wheeled lawn mower does not coage. In the role of cutting tools in trimmers, iron knives or a special fishing line for a trimmer are used, which is tucked into the coil of a trimmer for grass. However, unfortunately, the trimmer heads in the process of use over time become unusable. Certain malfunctions of course to remove at home, and with some, a complete change of mowing head will come in handy.

Cassyle heads for trimmers have various designs. both ordinary and complex. The figure below shows an automatic trimmer head from the Husqvarna motorcycle (Husqvarna).

This type of head is in configuration of most benzocosyles and electrimmers, such as Stihl (Stihl), Patriot (Patriot), Champion (Favorite), Bosch (Bosch), Huter (Huter) and others. The device of the braid head is quite common. It includes subsequent details:

  • the base of the mowing head;
  • button for automatic supply of the cord;
  • Spulk (coil), where the fishing line for the trimmer is refuel;
  • spring;
  • eyelets. through their fishing line for a trimmer it goes outside;
  • trimmer head cover;
  • Trimmer fishing line (cord).

There are also more ordinary trimmer heads shown in the next photo.

These nozzles do not allow you to change the length of the fishing line in automatic mode (after pressing the button). If the passage of the cliff of the cord, you have to stop the mowing and change it manually.

Users of the electrimmer and lawn mowers often face the inconsistency associated with an automatic mowing head. Coil malfunctions are subsequent:

STIHL Motokos, refueling the string in the Autocut 25 2 2

If, with a light blow, the trimmer coil button for grass on the ground is not lengthened for a trimmer, then the prerequisites are subsequent.

Option 1. it came out snacking, t.e. Squeezing the cord between the turns. This non.bond usually occurs if the user wound a fishing line for a trimmer to the coil unevenly, with a crossbreed of turns, or wound it with the missing tension. In the latter case, when the mowing head is rotated at huge revolutions under the influence of centrifugal force, the cord begins to delay, and as a result you are inter.trustee pouring the fishing line. To eliminate the difficulty, you will have to disassemble the coil on the trimmer and rewind the cord correctly, in other words, even coils with good tension.

Option 3.2. very short ends protrude from the head. A fishing line for a trimmer may not exit when hitting the ground, if its ends sticking out of the head are insufficient (short). Then the centrifugal force is not enough for the fishing line for the trimmer to stretch. Therefore, it is required to suspend the unit (drown out the engine differently disconnect the ethletric trimmer for grass from the network) and pull the fishing line for a trimmer manually, after pressing the button.

Option 3. A fishing line for a trimmer was soldered by a snot of a spitter head. This leads to the fact that the coil stops does not spin when the button is pressed. In the main thing, this happens for several reasons: the bad quality of the cord, overheating of the coil during prolonged operation of the unit, a string of fishing line on solid items.

  • At the beginning of the cord of the advantage of manufacturers, you will like more of low.quality and fusible materials that do not hold mechanical and temperature loads. Therefore, preference should be given to “branded” fishing.
  • If you, in spite of this, got a fishing line for a trimmer of an unknown property, and it is often soldered at one time of work, then you can follow the example of certain users, which, after refueling the cord, moisten it or silicone grease (from a spray can), or mineral oil). This procedure greatly reduces the possibility of soldering a fishing line with each other.
  • Also, a fishing line for a trimmer can sleep if at one time the mowing she hit a hard object (stone, fence, dry branch, etc.D.). At the end of this, it is a little stretched and draws back into the head with a high speed. The cord is heated from friction, and its turns are stuck together. The only thing that is done to eliminate this malfunction is to open a trimmer coil for grass and rewind a fishing line for a trimmer.

About the manufacturer

The history of this German brand begins in 1926. At the initial steps of its own development, the company was engaged in the production and implementation of various devices for washing and steam machines. It all began, like many companies, with small production and narrow orientation, which made it possible to focus on the quality of the manufactured products.

At first the 30s, the first stihl chainsaw was released, which is distinguished by convenience and functionality in those days. The company is developing at a great time, having introduced new tools everywhere, which gives it the opportunity to enter the international market. The Stihl lawn mower and already in 1931 organized the 1st permanent supply of products at the present moment, the company launched its activities in more than 160 countries of the world, opening new centers and production departments in Switzerland, China and many other states. This is fully explainable, because the assortment of the company is impressive: motorbuses, gasoline sprayers, mowers, gasoline trimmers for grass, chainsaws and almost everything else. It is a hunt to note that Shtil chainsaws are very popular due to their own functionality and applicable cost.

The relatively high price of STIHL products can be scared away by many, but if you think about what is more important. reliability and good result or savings that are in harm with the quality? But, if you set out to save money, we offer you an option for the lawn mower with your own hands, collecting the device with your own efforts you will know all the nuances and the structure of the tool.

Of course, you can choose cheaper Chinese counterparts, but then no one can vouch for the result of the final work and for the life of the service, which is very short.lived among such models. So it is more profitable to purchase a mow from an authoritative company once, which is certainly Stihl, and enjoy stable work for many years of operation.

Conclusions. which head with a coil to choose for a trimmer for grass

Summing up, consider when buying heads for trimmers for grass and lawn mower, the following factors:

Type. It can be a small lawn with young green grass or several hectares of area with thick.nisted vegetation. For the second case, you may need to purchase a metal knife for a lawn mower the number of segments of the fishing line protruding from the head. This amount can be different-from one to 6-8 pieces. The larger the number of fishing line segments, the higher the speed of the urgent

In addition, the more segments, the smaller the grass is grinded when it is driven by the fastening axis. as a rule, household and professional instruments have different mounting diameters, which is important to consider when buying a head. Even if you bought a coil with a landing hole that does not fit your tool, then the problem is solved by using special adapters type of fastening axis. they are fixed and rotating on different angles from 90 to 360 degrees

The presence of a rotation function allows you to perform grass mowing even in the most inaccessible places of the diameter of the fishing line. depends on the power of the power unit. For low.power trimmers, fishing lines with a thickness of 1.3 to 1.6 mm are used, and cords from 1.8 mm thick are used for more powerful units

Sometimes for choosing the optimal model for a trimmer for grass it takes a lot of time, therefore, given all the tips and recommendations, you can significantly reduce these costs.

| Denial of responsibility | Contacts |RSS