stripper ws 06 kwt

wire stripper ws 06 kwt

Gone are the days when stripping wires insulation was solely the prerogative of a hand knife. Today there are many models of so-called strippers. strip tool. One of the most successful, universal and convenient strippers can be rightly considered a model WS-04 from KVT. Let’s take a closer look at the design and principle of operation of this interesting tool.

The WS-04 stripper comes in a blister pack, on the back of which you can read the specifications of the tool. Let’s briefly list them:

WS-06 от КВТ. Съёмник изоляции. Плюсы и минусы.

  • Insulation stripping of wires with 0,05-6,0 kV section.mm.
  • Cutting of wires cross section up to 6 kV.mm.
  • Crimping lugs (insulated, non-insulated, auto-cleamp).
  • Microtuning screw for stripping wires with cross-section less than 0.2 kV.mm.
  • Ergonomic handles with soft rubber inlays.
  • Stripping length adjuster (detachable).
  • Housing surface finish. blued.

The handles are pressed together. jaws closed and separated. Blue part. Isolation length limiter.

Handle pressed. Back view.

The principle of operation of the tool is based on the initial bilateral gripping of the insulation (cutting into the insulation) of the wire by the jaws with deep incisions (applied at a certain angle), working on the plough principle (forward movement leads to holding and/or deeper cutting into the insulation), followed by a sharp (jerk) movement of the jaws aside, the insulation is torn and stripped. It is important to note that the tearing of the insulation is not a result of an even spreading of the stripper‘s jaws but a result of a jerk. The rear metal plate, covered with plastic caps, with a hole for a small conical metal pin to enter, is responsible for this sharp behavior of the tool. If you apply some force to the handles of the tool, the metal plate will rise (a slight bend at the base) and disengage from the pin and the jaws will separate sharply. By changing the length of the pin (depth of insertion into the hole) the jerk force is regulated (with the microtuning screw).

See also  Wire stripper ws 07

Rear view without, plastic covers. You can see the metal plate with the hole and the pin in the hole.

Rear view, without plastic covers. Handles pressed. Metal plate is out of mesh with the pin.

Example of stripping the insulation from a 4 kV single wire.mm.

Putting wire between jaws, as far as it goes.

Lightly depress the handles. jaws clamp wire.

Press the handles all the way down. insulation stripped.

Stripping tool WS-11 (KVT)

The company provides returns and exchanges of this product in accordance with the requirements of the law.

Return time

Returns possible within 30 days after receipt (for goods of proper quality).

Delivery of goods back according to agreement.

According to the current legislation you can return the goods of proper quality or exchange them if:

  • the goods have not been used and have no traces of use by the consumer: scratches, chips, scuffs, stains, etc. п.;
  • the goods are fully completed and the factory packing is preserved;
  • All labels and factory markings are intact;
  • The product retains its appearance and consumer properties.

stripper

0 wire stripping tool.05-10 mm2 wire cutting cross-section up to 10 mm2 stripping flat wires VVG-P, PUNP crimping lugs 0.5-6.0 mm2

In the standard range 0.2-10 mm2: automatic adjustment to the correct size and thickness of wire insulation In the micro range 0.05-0.2 mm2: use of microtuning screw Reinforced pressing jaws. Grip width: 13 mm Window for insulation cuttings discharge, thanks to which the stripped insulation does not get stuck in the mechanism Simultaneous stripping of up to 3 wires in one action, thanks to the wide holders Function of partial stripping of insulation. Notch and shift Built-in module “CutPro” for cutting wires. Professional blades instead of the sharpened section on the metal body in the WS-04 and WS-07 Types of crimped lugs: Uninsulated lugs and auto-crimp for double crimping Metal flanging of the mechanism protective cover Removable stripping length regulator with a screw fixing the regulator position New ergonomic handles with increased area made of non-slip rubberized material A hole on the handle for tool attachment to a carabiner Two built-in return springs Weight: 360 g Length: 206 mm

Limited Liability Company INSTRUMENTALelectro

See also  Window glass retail cutting

220040 г. Minsk, Korotkovaya str. Maksim Bogdanovicha str. 142, room 3

Date of registration in the Commercial Registry/Domestic Services Registry: 24.06.2020

Number in the Commercial Register/Registry of Consumer Services: 485120, Republic of Belarus

Registration authority: Minsk city executive committee

Location of the book of Комментарии и мнения владельцев and suggestions: 220040, ul. М.Bogdanovicha 142, pom.3

| Denial of responsibility | Contacts |RSS