The gas station starts and stalls the cause and elimination.

Why is a trimmer not starting for grass gasoline? Reasons and their elimination

Agree that almost any problems with the trimmer can be solved independently without resorting to the help of specialists. Когда не заводится газонокосилка, причины и способы устранения неисправности лежат на самой поверхности. You only need to carry out a thorough diagnosis of the device and determine the key causes of problems.

In this article, we will consider the popular causes of breakdowns of benzocose, ways to detect them. Here is a repair recommendations at home. To simplify the understanding of the process by beginners in this matter, we will provide material for visual photos and detailed video instructions.

Checking the fuel mixture

Suppose you don’t start a trimmer for grass. In this case, the first thing is to check whether the fuel is enough in the tank, as well as evaluate the quality of the fuel mixture. To refuel a motorized unit, it is necessary exclusively high.quality gasoline. It is recommended to use fuel, the brand of which is not lower than AI-95. Refueling a trimmer for grass with fuel of unknown origin, not bought at a gas station, is fraught with frequent failures in the work of the tool. This can cause a breakdown of the cylinder-piston system. Repair in this case often exceeds the cost of the device itself.

Why is a trimmer not starting for grass gasoline? Incorrect preparation of the fuel mixture may also lead to this, which consists of oil and gasoline. The proportions in which the specified components are connected are indicated by manufacturers in the guide for the operation of a trimmer for grass. Preparing the fuel mixture is extremely not recommended in large volumes, that is, for the future. Indeed, with prolonged savings, there is a loss of the determining properties of the substance. Therefore, if a trimmer for grass does not start, it is worth draining the old fuel and use freshly prepared fuel mixture.

What could break

Malfunctions with a benzocosa associated with the fact that this device is not started, in a certain way are classified by specialists of service services. They stand out malfunctions with the following nodes of the mechanism:

  • the engine in which the piston and bearings can be worn out or fail to crack the crankcase;
  • the fuel supply system, while it is possible to clog the filter or problems with the carburetor;
  • mechanical damage to wires, tubes, hoses;
  • The ignition chain.

To correctly determine the knot where the breakdown occurred, it is necessary to pay attention to the circumstances of the trimmer stalls for the grass.

Ways to eliminate breakdowns

Subsequent work is likely on the carburetor:

station, starts, stalls, cause, elimination
  • cleaning and adjustment of the fuel supply valve;
  • similar work with a valve producing redesigned gases and pairs (after burning fuel);
  • replacement of the spring more weak on the entrance valve;
  • restoration of the tension of the carburetor cable;
  • replacement of the fuel leaks hose, verification and strengthening of a weakened connection;
  • changing the rotor damper disk;.
  • Change of faulty wire or ignition coil.

Immediately after the start

Smelting Motokos or a trimmer for the grass after starting is justified by subsequent reasons:

  • impressive of previously adjusted valves;
  • first the wrong settings of the valve mechanism;
  • clogging with deposits of the fuel supply valve;
  • the hose is worn or poorly annexed.

Due to the violated method of injection of a fuel, a lawn mower or a trimmer for grass is very vibrated in work.

The trimmer for grass stalls. how to eliminate the problem

A gasoline trimmer for grass is a useful tool for cleaning from unnecessary grass of house territories and large area lawns. The design of this technique is quite complicated, therefore, if the device breaks, there may be several reasons. The most likely factors that have caught a breakdown are usually described in the user guide. Knowing why a trimmer for grass stalls, you can try to independently eliminate the defect. The most common malfunctions provoking the motorcycle stops, and the ability to repair them with your own hands is in the material further.

In order to most accurately determine the cause of the trimmer malfunction for grass of any brand (for example, echo) and find out the possibility of eliminating it, you need to install, when performing what action the device stalls. The engine can turn off both at idle and at high speeds, heated under load or immediately after starting and t.D.

If you stalled after gas supply

Owners of gasoline braids often mention that the lawn mower stalls when you press the gas. Usually such a breakdown occurs due to problems in the carburetor. A failure in his work can occur due to long-term storage, use in difficult conditions, significant overload of the motor. The symptom of such a breakdown will be vibrating movements of the device during operation.

On a note! Users familiar with the repair of a car carburetor can try to restore this important node of the trimmer for the grass on their own, using the instructions for operating. Otherwise, the correct decision will be to seek help from the service center representatives.

Sometimes a trimmer for grass stalls when you give gas because the fuel valve is clogged. This interferes with the supply of gasoline. To eliminate the problem, it is enough to loosen the valve. Thus, normal supply of carburetor fuel will be restored.

Another possible reason why the lawn mower stalls when gas is supplied is pollution of the soundtress (check valve). This detail prevents the appearance of a vacuum in a gas tank. If it is clogged, the air does not flow, which means that fuel does not go to the carburetor. To eliminate the problem, it is necessary to clean this element.

If it stalled at high speeds

If the carburetor stalls at high speeds, this means that in idle and small there are enough incoming fuel, and to work on high is not enough. Then it is necessary to check the serviceability of the following nodes of the trimmer for the grass.

  • Fuel hose. its integrity could be violated as a result of cracking. In this case, you need to replace the part. Or maybe you just need to tighten the clamps.
  • A filter network between a carburetor and a hose for supplying a gasoline mixture-it could clog. In this situation, it is necessary to clean the detail.
  • The valve on the gas tank cover. he could stick or clog with garbage. Cleaning is also necessary.
  • Carburetor. perhaps as a result of constant vibration, it was resolved. This is usually characteristic of cheap Chinese details. To eliminate the problem, it is necessary to set up according to the instructions. In some cases, it is enough to only weaken the tightening of the carburetor case. If the adjustment is not possible, it is necessary to install a new element.
  • Additionally, check the air filter. Perhaps it will need to be washed and cleaned or replaced with a new one, as he could clog with dirt and particles of grass when tilted technology, when the user mowed in hard.to.reach places.

If you stalled during work idle

If the lawn mower stalls, working idle, there may be several factors reasons.

  • First you need to check the prepared fuel solution, when it comes to a four-stroke trimmer working on a gasoline-oil mixture. There is a chance that it is made incorrectly. the proportions are not withstanded. Because of this, the gearbox is warming up, and the revolutions on the drum are lowering.
  • Another probable cause is blockage of elements such as a throttle, air filter or carburetor. You need to clean the indicated details.
  • Another possible factor is to resolve or incorrectly carried out carburetor adjustment. You need to adjust the setting according to the instructions.
  • Observe this problem mono and when opening the air damper. In this situation, the lack of fuel for a trimmer for grass occurs through the fault of the air flow.

If the device does not have enough fuel, it works properly at high speeds or when they increase, but stalls at idle. If the root of the problem consists in the carburetor, the lawn mower will be disconnected both with cold startup and hot.

If you stalled after starting

If the technique starts and stalls immediately after starting, this indicates the wrong settings or deducting the device. As a result of this, the fuel enters the engine unevenly, which leads to significant vibration and disconnecting the trimmer for the grass. To fix the breakdown, it is necessary to reconfigure the device according to the user management.

Another probable problem is the blockage of the valve supplying the gasoline mixture. It must be cleaned.

On a note! If the trimmer for the grass starts, but immediately stalls, it may also mean that the fuel is moving to the carburetor with difficulty. Weakening the valve will help to eliminate the problem. this will provide uniform and free circulation of fuel in the device.

Another possible reason is the damaged fuel intake hose. Air can penetrate through cracks and holes into the system. To solve the problem, you need to increase the engine speed in order to get rid of air bubbles that have penetrated the device.

If you stalled when opening the damper

If the technique works properly at idle, but stalls when opening an air damper, this reports about the penetration of air into the system through cracks in the fuel supply hose or damaged oil seals. To fix the breakdown and establish the work of the tool without driving air from the atmosphere, it is necessary to replace damaged parts.

НОВЫЙ ПОРТ ИГРЫ GAS STATION SIMULATOR НА АНДРОИД И IOS!!! ССЫЛКА В ОПИСАНИИ!!!

Preventive measures and operating rules

So that the lawn mower does not work and does not stall when starting, it must be correctly stored and operated. Compliance with the following simple recommendations will forget about problems.

  • When begging the grass, you need to monitor the state of the cooling system. It is also necessary to regularly clean the channels in the case and starter’s ribs.
  • To clean the tool, you should use kerosene, solvent, or other washing tools.
  • You can not clean a hot tool. it must cool before washing.
  • It is important to observe the recommended working mode. this will avoid overheating of the engine.
  • If a braid for grass is not used over the next thirty days, the fuel must be drained, otherwise it will fall into heavy components that can score the channels of the carburetor.
  • After the fuel is merged, the trimmer for the grass should work at idle for some time until it turns off. This will allow you to completely get rid of the rest inside the working mixture.

To store the tool in cold weather, you need:

  • completely drain the fuel;
  • disassemble the lawn mower, wash and clean all available components;
  • inspect the condition of the parts, eliminate all defects that can be corrected;
  • pour the required amount of oil into the gearbox;
  • Clean the air filter;
  • perform partial disassembly of the engine, wash all moving parts, blow and lubricate thoroughly;
  • To lubricate the piston, unscrew the candle, then raise the piston to the upper dead point by the starter, pour a small amount of oil into the hole for the candle and do the crankshaft several times.

Important! If there is no way to store a trimmer for grass in a warm dry room, you must first wrap the motor with an embarrassed rag.

Only by observing these rules, you can be sure that the lawn mower will work properly and will not stall for a number of seasons.

As you can see, stopping the work of a trimmer for grass can be caused by many reasons. Most of them can be fixed independently using the user instructions. In cases where there is no self.confidence, the equipment is recommended to be attributed to repairs. It is worth remembering that incorrect actions can cause even greater harm to the trimmer. As a result, the repair of Motokos will cost a much larger amount than it would be initially, and in the worst case, it may be necessary to buy a new unit.

The main thing. Fuel mixture!

Suppose you don’t start a trimmer for grass. In this case, the first thing is to check whether the fuel is enough in the tank, as well as evaluate the quality of the fuel mixture. To refuel a motorized unit, it is necessary exclusively high.quality gasoline. It is recommended to use fuel, the brand of which is not lower than AI-95.

Why is a trimmer not starting for grass gasoline? Incorrect preparation of the fuel mixture may also lead to this, which consists of oil and gasoline. The proportions in which the specified components are connected are indicated by manufacturers in the guide for the operation of a trimmer for grass. Preparing the fuel mixture is extremely not recommended in large volumes, that is, for the future.

Another common cause, due to which a trimmer for grass does not start, is the presence of a blockage in the filter area. To confirm the conjecture, just dismantle the indicated block and try to start the unit without it. If the engine of the trimmer for the grass has launched, most likely you will have to replace the air filter or at least perform a thorough purge of the old.

In the presence of abundant contaminants on the surface of the filter element, it is necessary to use a new grid. Relying to such actions, you should not leave a suction pipe at all without a filter. After all, rush in this case can lead to the need to repair the entire piston group of the unit engine.

In this case, the remains of plastic plastic dissolved in the brutal environment are created in the combustion chamber so terrible things that you will definitely not be able. Why does a trimmer for grass stall when you press the gas? The reasons for stopping a trimmer for grass at high and idle speeds, when heated or opened by an air damper. But you certainly remember how to correctly store fuel.

What to do when the fuel was definitely ordinary, there is a spark, but a trimmer for grass does not start a gasoline? Maybe you just flooded the candle with gasoline. In this case, it needs to be unscrewed, wiped with an unspoken rag and dry. By the way, it will be completely useful to check the spin for performance itself.

How to clean and store a tool?

During the operation of the lawn mower, monitor the state of the engine cooling system. The channels available in the starter housing, as well as the cylinder ribs, should always be clean. If you ignore this requirement and continue to operate the motorcycle, then you can disable the engine due to overheating.

Competent care of gasoline scythe during operation allows you to use it for several seasons in a row without serious repair

Before cleaning, let the engine cool down. Take a brush with a soft pile and clean the outer surface from dirt. Cleaning plastic parts is carried out by solvents, including kerosene, or special detergents.

After the summer season, the lawn mower should be prepared for long.term storage. To do this, the fuel mixture is drained from the tank. Then the engine is launched in order to develop fuel residues in a carburetor. The entire tool is well cleaned of pollution and sent to “hibernation”.

As you can see, it is possible to repair the malfunctions of the household lawn mowed on their own. Service services should be contacted in case of serious breakdowns. In this case, the cost of repairs with the price of a new lawn mower should be correlated. Perhaps it will be more advisable to buy a new tool.

Why is a trimmer for grass stops when you press the throttle, with high and lack of speed, when heated or opened by the air damper

A gasoline.drive grass braid is a useful thing for owners of home plots, lawns, and when a trimmer for the grass suddenly stops, work on cleaning the territory from the grass stops. The device itself is a rather complex mechanism, so there are many reasons for its breakdown. The most common faults are operating instructions. Know the reasons why the trimmer stops for the grass, it is necessary to repair the device yourself.

The lawn mower stalls when you press the gas

The hole in the fuel cover (saepun) of a trimmer for grass

With a similar problem, it is worth paying attention to the fuel valve, which, when clogging, ceases to normally pass the fuel mixture. By solving this malfunction, it is weakening using a suitable tool. In addition, the problem with the circulation of the fuel mixture may cover in the contamination of the valve. To do this, just blow it with a stream of compressed air.

If you stalled when opening the damper

If the technique works properly at idle, but stalls when opening an air damper, this reports about the penetration of air into the system through cracks in the fuel supply hose or damaged oil seals. To fix the breakdown and establish the work of the tool without driving air from the atmosphere, it is necessary to replace damaged parts.

Another possible reason for the breakdown is the malfunction of the carburetor dosage system. To eliminate this problem, it is better to contact professionals.

At high speeds

When a braid for grass stalls at high speeds, this is due to the following problems:

  • clogging or clutching a valve located on the gas tank lid;
  • The carburetor was diluted under the influence of vibrations arising during the operation of the mechanism;
  • problems with the circulation of the fuel mixture;
  • atmospheric air
  • The hose intended for fuel fuel cracked or slightly connected.

The carburetor is regulated by relying on the operational instruction to the trimmer. For configuration, it is often enough to weaken the tightening of its body. If there are problematic issues with the circulation of the fuel mixture, then it can gradually enter the carburetor. After its production, the engine stalls at high speeds.

The performance of the spark plugs

If there is a need to figure out why a trimmer for grass is not started, then the state of contacts of the installed candle should be checked. In this case, you can figure out why the lawn mowing engine does not occur. For high.quality diagnosis of the spark plug, you must definitely adhere to the following scheme:

  • If during the dismantling it was found that the candle was wet, then in a small combustion chamber there is a certain part of the fuel, from which you do not need to rush to get rid of. To eliminate the problem, it is necessary to dry and carefully clean the contacts. After the manipulations done, you should carefully connect the candle. You need to turn on the ignition and without unnecessary efforts pull the starter handle. If the device is regular, then there will be a constant and bright spark. Otherwise, you have to replace the candle.
  • The state of involved electrodes can be considered ideal when they have a characteristic dark brown fog. If the candle has a white or even black soot, as well as wet, then it must be immediately replaced.
  • A trimmer for grass may not respond to launch due to the fact that there is too much gap between the contacts of the candle. To set the optimal gap, you need to use special multibody probes.

If, after all the manipulations done, the engine of the lawn mower did not start, then the cause of the malfunction must be sought in a carburetor or heat supply. Otherwise, you will have to check the serviceability of the involved high.voltage wire.

Not starting on a cold trimmer for grass. we eliminate the cause

On the cold.The reason is an air leak that does not allow fuel to download. In the camera.

After several jerks, he will start and stall, which is a normal phenomenon. What to do when the fuel was definitely normal, there is a spark, but a trimmer for grass does not start a gasoline? Putting the damper to the working position, start the tool again and start working.

What in the end

As a result, we add that the fuel highways, connections and hoses are rubber products. For this reason, you should keep in your head that the natural aging of rubber occurs. On cars that are more than 10 years old, a frequent phenomenon becomes cracking in rubber hoses, which leads to a suction of air. It should be added that the outer state of such hoses is not a clear indicator of their condition. The inner surface of the walls is also destroyed, which leads to an inconspicuous one from the outside of particles in the injector, carburetor or fuel pump, especially in cases of the appearance of the task in areas behind the fuel filter.

Read trimmer for grass gasoline does not develop the moment

The main prerequisites, according to the engine, begins to stall after warming up. Frequent obstacles of carburetor and injector engines, diagnosis of defects.

The car engine starts and stalls immediately after starting: the main prerequisites for this malfunction. Diagnosis of probable circumstances, tips and tips.

As a result of what there are jerks and failures when recruiting, the car pulls in motion on transitional modes. Prerequisites and elimination of defects.

Swimming idle revolutions of the motor “on cool”. The main malfunctions, symptoms and detection of breakdown. Non.blessed idle motor.

The prerequisites, according to the accelerator pedal after pressing the pedal of the accelerator, and the engine begins to zoopet. Motor failures with HBO when switching from gasoline to gas.

Why the engine can have high.speed revolutions. The main prerequisites for the large revolutions of the XX on the injector motor and engines with a carburetor.

At idle

At single speeds, the common reasons for stopping a trimmer for grass are as follows:

  • reducing the speed of the gearbox when heating it, which is a consequence of the use of inappropriate fuel mixture;
  • clogging of the throttle;

If a carburetor is a problem place, then the technique will stop at the “cold” and with a “hot” launch.

The trimmer for the grass starts and immediately stalls the reasons

In recent years, the gasoline trimmer for the grass has made the status of a textbook from the main tools in the arsenal of summer residents. And such actions are logical, because a motorized braid for grass allows you to quickly put a personal plot in order. But when it happens that the trimmer for the grass does not start on the hot and cool. In such situations, it is necessary without the help of others to establish the cause of the malfunction. Next, find out what to do if a trimmer does not start for grass. The prerequisites that for the most part lead to such troubles will be considered further.

Where to start the diagnosis of defects if a trimmer is not started for grass? In situations where the tool stalls immediately after launch, it is worth looking at the subsequent units of the unit:

Старший сержант Міхайло ДІАНОВ: “Ми не любим, коли нас називають герої. Герої лежать в землі”

Specifically, the breakdown of the above locations for the most part leads to the fact that a trimmer for grass is poorly started. It is necessary to consider how to remove such problems.

Suppose you don’t start a trimmer for grass. Then the beginning of everything needs to be checked whether the fuel in the tank is enough, to additionally evaluate the quality of the fuel consistency. It is necessary to refuel a motorized unit only with high.quality gasoline.

It is recommended to use fuel, the brand of which is not lower than AI-95. Refueling a trimmer for grass with fuel of unknown origin, acquired not at a gas station, is fraught with the appearance of frequent failures when working as a tool. This causes a breakdown of the cylinder-piston accounting system.

Repair under such circumstances often exceeds the price of the device itself.

Why is a trimmer not starting for grass gasoline? Incorrect preparation of fuel consistency can also lead to this, which consists of oil and gasoline. The proportions, in which the designated components are connected are indicated by manufacturers in the guide for the operation of a trimmer for grass.

Preparing the fuel mixture is not very recommended in large volumes, in other words for the future. Indeed, with prolonged savings, the loss of the determining parameters of the substance occurs.

If a trimmer for grass does not start, it is worth draining old fuel and use freshly prepared fuel consistency.

The trimmer for the grass on the cold is poorly started, what to do?

What to do if the used fuel mixture is in perfect order, alas, as before, a trimmer for grass is not started by gasoline? The prerequisites for the refusal of the mechanism are variations to cover in excess moisture of the candle channel. To diagnose and eliminate difficulties, you need to make the next:

  • Turn the candle. Wipe it painstakingly, and then dry it.
  • Drain the excess combustible in the chamber through the corresponding candle hole.
  • Clean an old candle if there is a dozen on its surface. The use of an ordinary ladies’ nail file or file will allow you to cope with the task.
  • To install the element in the area, set a gap of 1 mm. To check the parameter, it is enough to place any coin in the lumen.
  • Collect a multifunctional block back.
  • Try to start a trimmer for grass.
station, starts, stalls, cause, elimination

It is recommended to do drying the candle channel by minimum within half an hour. But do not resort to calcining its parts. After all, heating the spark plug leads to its ultimate corruption.

Что сделать, если сервис многофункционального блока выполнялось согласно вышеуказанным советам, но триммер для травы не заводится, искра конечно при всем этом? Here it is worth treating gasoline threaded connection. The latter should not be plentifully impregnated with combustible. It is only a little moisturized.

Resort to such actions should be to ensure the ignition. After all, no matter how the candle gives a strong spark, in a completely dry chamber there simply will not be something to ignite.

If even a trimmer for grass does not start here, it is worth evaluating the quality of contact between a high.voltage wire and a candle. For which the design of the absence of a spark is intended (in the presence of a reliable connection with the designated elements), for sure, the inconsistency is caused by the breakdown of the ignition unit. In this situation, you will have to turn to the services of masters who will reinstall the knot.

After starting, the engine immediately stalls? why is this happening

Another all.produced prerequisite, because of which it is required, does not start a trimmer for grass, is the presence of a blockage in the filter area. To confirm the hypothesis, quite dismantle the designated block and experience the unit without it.

If the engine of the trimmer for the grass has launched, most likely you will have to create a change in the air filter or at least perform a painstaking blowing of an old. In the presence of abundant contaminants on the filter element, you need to use the latest grid. Relying to similar actions, it is not recommended to leave an absorbing pipe completely without a filter.

After all, haste in our version leads to the need to repair the entire piston group of the unit engine.

Often the engine of branded models of trimmers stalls during the clogging of the sapun. The main task of the designated component is the leveling of pressure in the fuel tank. For which the design of the node is intended here, a vacuum appears here, which greatly complicates the supply of fuel. Removing a malfunction allows the cleaning of the cabin using an ordinary sewing needle.

The measured functioning of the trimmer for the grass will be more impaired due to the laying of dirt in the final channel or the formation of blockage on the muffler grid. Such a disorder in most cases appears during the operation of the older generation trimmers. The issue is being solved by dismantling the anti.diploma mesh and its cleaning.

So that the unit is always in a multifunctional state, it is worth observing several ordinary rules:

  • Carry out timely, constant technical inspection of the main mechanical nodes of the device.
  • To refuel a trimmer for grass only with the latest fuel, the quality and origin of which is not caused by fluctuations.
  • To inspect after each use of the tool, whether oxides and soot formed on parts of the accounting ignition system.
  • Avoid the strong load of the trimmer for grass during work.

saw stall when you press the gas

So that the unit remains in a working state, you need to correctly prepare it for storage during the cold period.

station, starts, stalls, cause, elimination

Trimmer does not start for grass. Why?. Agrotechervice

A gasoline trimmer for grass is an amazingly useful thing, with the help of which you can, without unnecessary troubles, put in order not only a miniature lawn in the backyard of the house, but also to dig a considerable size of the lawn. But, like all things in this world, it has the ability to break. In this article, we will try to figure out what to do in cases where a trimmer for grass refuses to work.

The gasoline trimmer for the grass is poorly started

So, what to do if the gasoline trimmer for the grass is poorly started or not started at all? The most common reason for such a breakdown.This is poor.quality fuel. Remember that, for example, trimmers for the grass of brands “STIHL” and “Husqvarna” are unlikely to start the quality below AI-92.

Do not save on fuel, t.to. Repair of cylinder parts.the piston group can be a third of the entire cost of a braid for grass, and sometimes even half. Also, when preparing the fuel mixture, it is necessary to correctly observe the proportions of fuel and oil, which are always indicated in the instructions for the trimmer.

What to do if high.quality fuel is flooded in the gas tank, there is a spark, but the tool still refuses to start up? It is necessary to check the condition of the candle. It is located in the center of the gas mowing housing. It needs to be carefully twisted and make sure if there is a raid on it. If it is, then carefully clean the candle from the carbon and dry it.

If the lawn mower does not start even after the methods proposed above, then you need to try to remove the air filter and start the device without it. If the trimmer for the grass has not earned, clean the old filter well from dust or buy a new one.

It also happens that the lawn mower works as a maximum of 5 minutes, and then stalls and does not start until it cools down. In this case, try to open the pouring cover of a benzogornin. a suction sound should appear.

After that, tighten the lid back. If you do this manipulation during the time when the trimmer for the grass has just begun to stall, then the turns will recover, and it will be possible to continue to work.

If the lawn mower stalled until the cover is opened, then you just need to start it as it should be according to the instructions.

Trimmer for grass does not start after winter

How to be in such a situation? Do not worry and panic. This is a very common problem that is solved in just 3-4 minutes. Firstly, if the fuel is left in the gas tank last year, then it must be drained.

Gasoline loses its octave properties after 2 weeks of downtime. Secondly, start a lawn mower after a long stagnation in a slightly different way.

First you need to open the damper and pump up a little fuel mixture into the carburetor, then stretch the handle until a small resistance is sensed. After that, you can start a trimmer for the grass.

Trimmer for grass starts and stalls

If, when trying to start a trimmer for the grass, it starts up, but immediately stalls, then the cause of this may be an air filter again. It is necessary to remove it and check if it is clogged with dust.

If this is true, then it is necessary to carefully clean it or purchase a new. Also, the problem may also consist of malfunction of the ignition coil.

| Denial of responsibility | Contacts |RSS