Trimmer for grass for grass stalls at high speeds. Electric malfunctions:

The reasons for the fall in the motorcycle. The lawn mower does not develop full power

Any person owning a country or land plot is well aware of the problems of the fight against excess vegetation. Now a trimmer for the grass has come to the rescue, which successfully replaced the usual braid in this field. This unit is very convenient in work, but it, like any mechanism, also, due to difficult working conditions or incorrect operation, is characterized by failing. Situations are quite common when a trimmer for grass does not gain momentum. To understand this problem, it is necessary to understand some aspects related to the functioning of the device.

All trimmers for grass are classified according to the type of power: gasoline or electricity (from the network or battery). It should be noted that gasoline mowers in many respects exceed their electric and battery analogues. Despite the fact that they all perform similar functions, the difference in performance, maneuverability and effectiveness is very noticeable. However, the general principle of operation of all types of manual braids is almost no different- the devices are equipped with engines (two- or four-stroke ICE or electric motors), which drive the cutting unit (reel with fishing line or metal disk). All elements are fixed on the line of straight or curved shape, including the handle for controlling the trimmer on which the main buttons are located.

Since the problem of weak revolutions is more characteristic of gasoline trimmers, they will be given more attention. So, the lawn mower is very comfortable in work and unpretentious in maintenance. over, most of its malfunctions are caused by ignorance by the user of elementary things, which are written in the instructions. Therefore, before starting the operation of the unit, it is necessary to carefully study the management of the manufacturer. In particular, in order to start the engine, it is necessary to do the following sequential actions:

  • turn on the ignition button;
  • press the silicone button for pumping gasoline several times;
  • close the air damper;
  • The gas lever is installed in a position for high speeds;
  • first make non.leaf with the starter handle to feel the engine resistance, then jerk sharply.

If the lawn mower started up, but stalled, you need to put the air damper in the middle position and repeat the attempt. When the engine works, you need to slow the gas and open the air damper, since the trimmer for the grass functions only on the leak.

Important! The mode of operation of the trimmer for the grass depends on the various environmental influences. In hot weather, the unit should be given more time to cool. When working in conditions of dense thickets or high vegetation, the engine also overheats strongly. It is necessary to take five-minute breaks every 15-20 minutes.

The reasons for the weak.speed trimmer for grass

If users complain to the trimmer for grass, which does not gain momentum, this means that it works normally on idle, and when pressing gas does not develop the necessary power. This can happen as a result of a long downtime of the apparatus without activity. These problems are typical for gasoline devices, including the Husqvarna 128R, STIHL FS 38 and Hitachi different modifications.

Working with a trimmer, you need to monitor its behavior all the time. a drop in revolutions and unusual noises signal the malfunctions in the aggregate. Sometimes you give gas, and the trimmer for the grass swims. In such cases, the work should immediately be suspended, let the mechanism cool and start searching for possible problems. They can be of a different nature of both the technological plan and external factors related to the conditions and features of the operation of the device.

External factors

Several factors that are not related to its breakdown affect the reduction of revolutions:

  • filter pollution due to the hit of particles of dirt and dust in it;
  • use of poor.quality fuel;
  • incorrectly prepared mixture (relevant for trimmers with two.stroke gasoline engines);
  • pollution of the muffle of muffler particles of vegetation, soil elements and other objects.

In this case, in the second and third cases, the formation of a soil in the combustion chamber is formed, and the elements of the carburetor are clogged.

technical issues

The technical problems of the lawn mower mainly occur in the fuel and ignition system. You can cope with them yourself.

  • Когда ручная косилка не заводится или глохнет, проблема может быть связана со свечой. The dark cargo speaks of poor carburetor adjustment and low gasoline quality.
  • The reason for the incorrect operation of the trimmer for the grass may be clogged fuel hose. Filters are also often clogged.
  • Another internal problem. the muffler is covered with soot. From this, the turnover of the grass for the grass falls strongly. Output. you need to clean the muffler.

Important! If the unit does not work due to breaking up the engine, serious problems may occur. In this case, the malfunctions that can be eliminated with your own hands include only the destruction of piston rings. With more serious problems with the motor, if there is no warranty, you should be prepared to visit the workshop.

The lawn mower stall when you press the gas, how to eliminate the breakdown

The reasons why the lawn mower stalls is a huge number, we offer the most common of them, and we hope that you will find your own, and, of course, eliminate it. So, one of the situations is to clog the air damper, then the hole behind which the fuel is sprayed. If something got into it, then it can most often be quickly and easy to remove. This is the simplest reason, like a clogged filter. It needs to be washed in the solvent, and then get it well with compressed air. If it is not subject to repair, then order a new one in spare parts from the Kosikos store.

When a braid for grass stalls at high speeds, this is due to the following problems:

trimmer, grass, stalls, high, speeds
  • clogging or clutching a valve located on the gas tank lid;
  • The carburetor was diluted under the influence of vibrations arising during the operation of the mechanism;
  • problems with the circulation of the fuel mixture;
  • atmospheric air
  • The hose intended for fuel fuel cracked or slightly connected.

The carburetor is regulated by relying on the operational instruction to the trimmer. For configuration, it is often enough to weaken the tightening of its body. If there are problematic issues with the circulation of the fuel mixture, then it can gradually enter the carburetor. After its production, the engine stalls at high speeds.

The causes of the malfunction and their elimination

In order to most accurately determine the cause of the trimmer malfunction for grass of any brand (for example, echo) and find out the possibility of eliminating it, you need to install, when performing what action the device stalls. The engine can turn off both at idle and at high speeds, heated under load or immediately after starting and t.D.

If you stalled after gas supply

Owners of gasoline braids often mention that the lawn mower stalls when you press the gas. Usually such a breakdown occurs due to problems in the carburetor. A failure in his work can occur due to long-term storage, use in difficult conditions, significant overload of the motor. The symptom of such a breakdown will be vibrating movements of the device during operation.

On a note! Users familiar with the repair of a car carburetor can try to restore this important node of the trimmer for the grass on their own, using the instructions for operating. Otherwise, the correct decision will be to seek help from the service center representatives.

Sometimes a trimmer for grass stalls when you give gas because the fuel valve is clogged. This interferes with the supply of gasoline. To eliminate the problem, it is enough to loosen the valve. Thus, normal supply of carburetor fuel will be restored.

Trimmer malfunctions for grass

Trimmer for grass is a convenient and affordable replacement for the lawnical mower. Its cutting part is made in the form of fishing line, knives or disk installed on the drum, which is closed on top of the protective casing. The basis of the design is a bar, which is adjustable in height, at the end there is a comfortable handle and shoulder belt.

Like any other technique, a trimmer for grass may be unknown, and so that the breakdown does not lead to the final failure of the tool, we suggest you familiarize yourself with this article. Unit can break down for various reasons. Breakage occurs both in new trimmers and those that have long been operated.

A malfunction of electrical models

The reasons for the unexpected shutdown of an electric lawn mower are associated with a cliff of the cord or the absence of current. In the first case, it is recommended to check the cable for a cliff. To replace the power cord, you need to pull out the fork out of the outlet, open and dismantle the circuit lid.

Before unscrewing the squeezing of the cable? It is necessary to remember the diagram of its connection to the switch. To disconnect the cord, a hexagon is used (diameter 1 mm). The clip is released, the conductors are dismantled. To check the cable for a cliff, multimeter is used. If necessary, a new cord is installed. In this case, the reverse sequence is observed.

In the second case, it is recommended to connect another device to the mains. Electric devices may not work when the fuse is damaged in the fork. To carry out repair work, you will need to disassemble the fork. For this, a screwdriver and a tester are used.

Motor malfunctions occur when overheating of the lawn mower:

In the first case, it is recommended to wait a few minutes so that the motor cools. In the second case, you need to remove the stuck object. The effectiveness of the cooling system depends on the state of the air filter.

Dirty device poorly passes air, which helps to turn off the device. Experts advise cleaning and changing the filter once every 3 months (with constant operation of the lawn mower).

With a breakdown of the electric motor, the corresponding smell and noise appear. In this case, you need to replace the drive.

The vibration of the motor on idle, on a cold or warm engine: possible causes

Immediately note that there are many reasons for the emergence of vibration of the internal combustion engine, starting from the torn engine pillows (supports) and ending with ignition passes and the tag of power unit. For a more accurate definition, first of all, you should pay attention to one or other symptoms.

The fact is that vibration can be either constant (regardless of heating and loads on the unit), and manifest itself in a certain mode of operation (idle or high speeds, on cold or hot). Another engine vibration can manifest itself on a cold ICE, but as it warms up, it completely disappears. Let’s understand.

  • For example, if the engine was recently versed for repair (possibly capital), then there is a high probability that the crankshaft was not properly covered after the reverse assembly. The result is a beating and increased vibrations.
  • We also note that after repairing the motor to imbalance and vibrations, different weights can lead to the details of the cylinder-piston group. The more weight difference turns out, the stronger the vibrations will be. For this reason, experienced craftsmen weigh pistons, fingers, etc.D.
  • Often the reason for vibrations is that the engine is troit, that is, one or more cylinders for any reason do not work or work with failures. As a rule, the elimination of the cause of the touch automatically eliminates the presence of vibrations of the power plant.
  • Do not forget that the timing belt incorrectly set on the marks or the chain also causes vibrations.The reason is that the engine works unstable due to violation of the phases of gas distribution.
  • Many engines have in their design special balancing shafts that are necessary in order to “extinguish” fluctuations. Quite obvious, problems with these shafts will lead to an increase in the vibrations of the motor.

The engine pillows are one of the most common reasons why the engine vibrates. In fact, this is a damper made on many cars from rubber to absorb vibrations. As you know, over time, the rubber daggers and cracks, loses its properties as a result of technical fluids and t.D. The main thing is that the engine with a damaged pillow cannot work softly.

  • If you recently moved from one car to another, it should be borne in mind that different engines may differ in vibration loads. The number of cylinders, layout and a number of other features affect the level of vibrations. In simple words, the usual in-line engine for 6 cylinders can operate with less vibrations than a 4-cylinder and, especially, 3-cylinder engine. over, in this case, we are not talking about problems, since for a particular ICE a certain level of vibration can be considered the norm.
  • We also add to reduce vibrations, on the crankshaft of many engines there is the so.called dignified damp. If problems arise with the element, the motor will begin to vibrate more strongly.

As you can see, at the initial stage it is important to accurately determine the cause of the strengthening of vibrations. For example, in most cases, it is enough to replace the engine support or solve the problem on which the engine is troit. However, it also happens that the power unit itself needs to be disassembled and repaired.

Repair of mechanical braids is carried out when the cutting elements are blown up or damaged. In this case, experts recommend to independently dismantle removable knives. Evadal is used to sharpen them. If necessary, the battery is replaced in battery.

Before repairing the lawn mower, the type of motor is determined:

The lawn mower stalls at high engine speeds

During operation, a situation arises when, when pressing the fuel supply key, the aggregate turnover begin not to increase, but to decrease. A malfunction of this nature can be caused:

Fuel hoses Motokos with filter

  • etching of atmospheric air into the combustion chamber;
  • problems with the circulation of a mixture of fuel;
  • clogging the saapun in the lid of the fuel tank (cleaning the hole with a thin sewing needle);
  • Incorrect carburetor adjustment.

When air sunses, when I operate ICE, it is necessary to check the tightness of the pipes and the integrity of the gaskets in the CPG. The problem with the circulation of the fuel mixture can be solved by the elimination of blockages in the fuel pipes leading to the carburetor. If a vacuum occurs in the tank and not receipt of the fuel mixture to the carburetor, it is enough to clean the soundtress with a thin needle and blow it with air.

The trimmer for grass stalls. how to eliminate the problem

A gasoline trimmer for grass is a useful tool for cleaning from unnecessary grass of house territories and large area lawns. The design of this technique is quite complicated, therefore, if the device breaks, there may be several reasons. The most likely factors that have caught a breakdown are usually described in the user guide. Knowing why a trimmer for grass stalls, you can try to independently eliminate the defect. The most common malfunctions provoking the motorcycle stops, and the ability to repair them with your own hands is in the material further.

In order to most accurately determine the cause of the trimmer malfunction for grass of any brand (for example, echo) and find out the possibility of eliminating it, you need to install, when performing what action the device stalls. The engine can turn off both at idle and at high speeds, heated under load or immediately after starting and t.D.

If you stalled after gas supply

Owners of gasoline braids often mention that the lawn mower stalls when you press the gas. Usually such a breakdown occurs due to problems in the carburetor. A failure in his work can occur due to long-term storage, use in difficult conditions, significant overload of the motor. The symptom of such a breakdown will be vibrating movements of the device during operation.

On a note! Users familiar with the repair of a car carburetor can try to restore this important node of the trimmer for the grass on their own, using the instructions for operating. Otherwise, the correct decision will be to seek help from the service center representatives.

trimmer, grass, stalls, high, speeds

Sometimes a trimmer for grass stalls when you give gas because the fuel valve is clogged. This interferes with the supply of gasoline. To eliminate the problem, it is enough to loosen the valve. Thus, normal supply of carburetor fuel will be restored.

Another possible reason why the lawn mower stalls when gas is supplied is pollution of the soundtress (check valve). This detail prevents the appearance of a vacuum in a gas tank. If it is clogged, the air does not flow, which means that fuel does not go to the carburetor. To eliminate the problem, it is necessary to clean this element.

If it stalled at high speeds

If the carburetor stalls at high speeds, this means that in idle and small there are enough incoming fuel, and to work on high is not enough. Then it is necessary to check the serviceability of the following nodes of the trimmer for the grass.

  • Fuel hose. its integrity could be violated as a result of cracking. In this case, you need to replace the part. Or maybe you just need to tighten the clamps.
  • A filter network between a carburetor and a hose for supplying a gasoline mixture-it could clog. In this situation, it is necessary to clean the detail.
  • The valve on the gas tank cover. he could stick or clog with garbage. Cleaning is also necessary.
  • Carburetor. perhaps as a result of constant vibration, it was resolved. This is usually characteristic of cheap Chinese details. To eliminate the problem, it is necessary to set up according to the instructions. In some cases, it is enough to only weaken the tightening of the carburetor case. If the adjustment is not possible, it is necessary to install a new element.
  • Additionally, check the air filter. Perhaps it will need to be washed and cleaned or replaced with a new one, as he could clog with dirt and particles of grass when tilted technology, when the user mowed in hard.to.reach places.

If you stalled during work idle

If the lawn mower stalls, working idle, there may be several factors reasons.

How To Easily Fix A Quick, Rapid Loader LineHead

  • First you need to check the prepared fuel solution, when it comes to a four-stroke trimmer working on a gasoline-oil mixture. There is a chance that it is made incorrectly. the proportions are not withstanded. Because of this, the gearbox is warming up, and the revolutions on the drum are lowering.
  • Another probable cause is blockage of elements such as a throttle, air filter or carburetor. You need to clean the indicated details.
  • Another possible factor is to resolve or incorrectly carried out carburetor adjustment. You need to adjust the setting according to the instructions.
  • Observe this problem mono and when opening the air damper. In this situation, the lack of fuel for a trimmer for grass occurs through the fault of the air flow.

If the device does not have enough fuel, it works properly at high speeds or when they increase, but stalls at idle. If the root of the problem consists in the carburetor, the lawn mower will be disconnected both with cold startup and hot.

If you stalled after starting

If the technique starts and stalls immediately after starting, this indicates the wrong settings or deducting the device. As a result of this, the fuel enters the engine unevenly, which leads to significant vibration and disconnecting the trimmer for the grass. To fix the breakdown, it is necessary to reconfigure the device according to the user management.

Another probable problem is the blockage of the valve supplying the gasoline mixture. It must be cleaned.

On a note! If the trimmer for the grass starts, but immediately stalls, it may also mean that the fuel is moving to the carburetor with difficulty. Weakening the valve will help to eliminate the problem. this will provide uniform and free circulation of fuel in the device.

Another possible reason is the damaged fuel intake hose. Air can penetrate through cracks and holes into the system. To solve the problem, you need to increase the engine speed in order to get rid of air bubbles that have penetrated the device.

If you stalled when opening the damper

If the technique works properly at idle, but stalls when opening an air damper, this reports about the penetration of air into the system through cracks in the fuel supply hose or damaged oil seals. To fix the breakdown and establish the work of the tool without driving air from the atmosphere, it is necessary to replace damaged parts.

Preventive measures and operating rules

So that the lawn mower does not work and does not stall when starting, it must be correctly stored and operated. Compliance with the following simple recommendations will forget about problems.

  • When begging the grass, you need to monitor the state of the cooling system. It is also necessary to regularly clean the channels in the case and starter’s ribs.
  • To clean the tool, you should use kerosene, solvent, or other washing tools.
  • You can not clean a hot tool. it must cool before washing.
  • It is important to observe the recommended working mode. this will avoid overheating of the engine.
  • If a braid for grass is not used over the next thirty days, the fuel must be drained, otherwise it will fall into heavy components that can score the channels of the carburetor.
  • After the fuel is merged, the trimmer for the grass should work at idle for some time until it turns off. This will allow you to completely get rid of the rest inside the working mixture.

To store the tool in cold weather, you need:

  • completely drain the fuel;
  • disassemble the lawn mower, wash and clean all available components;
  • inspect the condition of the parts, eliminate all defects that can be corrected;
  • pour the required amount of oil into the gearbox;
  • Clean the air filter;
  • perform partial disassembly of the engine, wash all moving parts, blow and lubricate thoroughly;
  • To lubricate the piston, unscrew the candle, then raise the piston to the upper dead point by the starter, pour a small amount of oil into the hole for the candle and do the crankshaft several times.

Important! If there is no way to store a trimmer for grass in a warm dry room, you must first wrap the motor with an embarrassed rag.

Only by observing these rules, you can be sure that the lawn mower will work properly and will not stall for a number of seasons.

As you can see, stopping the work of a trimmer for grass can be caused by many reasons. Most of them can be fixed independently using the user instructions. In cases where there is no self.confidence, the equipment is recommended to be attributed to repairs. It is worth remembering that incorrect actions can cause even greater harm to the trimmer. As a result, the repair of Motokos will cost a much larger amount than it would be initially, and in the worst case, it may be necessary to buy a new unit.

Read the same from the heading

What gasoline in the Husqvarna lawn mower

Oil for the lawn mower: how to correctly change it and which liquid it is better to fill the lawn mower is a very necessary thing for those who need repeating mowing of grass on lawns and other earthen areas. But with the acquisition of this tool, one should not forget that he, like at least some other mechanism, asks for repeating maintenance. Basin gasoline Husqvarna to the lawn mower []

Huter gas mower adjustment of carburetor

Tuning the carburetor of the chainsaw of the chainsaw for an independent option of the carburetor, it is necessary to familiarize yourself with its device and understand the work order that is carried out to adjust the parts responsible for the correct functioning of the components of the device and the parts close to it. It is necessary to carefully handle objects for the option, also determine the compliance of the displayed characteristics of very acceptable values. About the device of the carburetor carburetor []

How to correct the fishing line for a trimmer to a gas station

A step.by.step annotation, how to wind a fishing line for a trimmer on a trimmer coil for grass with the advent of spring, you often spend your time in a dacha or a personal plot. From such a confusion as grass and weeds, you will be protected by a trimmer for grass. This tool without much work trims and mows grass in complex areas, where an ordinary lawn mower is not possible. Trimmer for grass. very effective and []

At high speeds

When a braid for grass stalls at high speeds, this is due to the following problems:

  • clogging or clutching a valve located on the gas tank lid;
  • The carburetor was diluted under the influence of vibrations arising during the operation of the mechanism;
  • problems with the circulation of the fuel mixture;
  • atmospheric air
  • The hose intended for fuel fuel cracked or slightly connected.

The carburetor is regulated by relying on the operational instruction to the trimmer. For configuration, it is often enough to weaken the tightening of its body. If there are problematic issues with the circulation of the fuel mixture, then it can gradually enter the carburetor. After its production, the engine stalls at high speeds.

What to do if the lawn mower or saw stalls at high speeds (under load)

Group for repairing garden equipment Video about the reasons for the sudden stop of a two.stroke.

The lawn mower does not start hot. press the gas trigger and pull the cord abruptly several times until the engine earns, then lower the trigger. Not starting. specialized repair is required.

Checking the ignition system, if the lawn mower is not started, is carried out sequentially:

trimmer, grass, stalls, high, speeds
  • Clean the removed candle from soot and dirt, dry, set a gap of 1 mm;
  • Connect to a high.voltage wire and check on a spark, twitching a few times;
  • In the absence of a spark, check the high.voltage wire for integrity;
  • replace the candle;
  • dry the candle channel;
  • At the same time, the operation of the ignition coil is checked, it is faulty if the working candle does not spark.

It is in the case of a malfunction of the ignition coil that the lawn mower does not start hot, stalls, works with interruptions.

Cleaning or replacing the air and fuel filter will provide the necessary consumption of ingredients entering the carburetor. Air filter can be washed in soapy water or replaced. If the nylon canvas is used, it is washed, the porous felt filler is replaced. Why does the lawn mower stall when you press the gas: the causes and their solutions. The lawn mower stalls (trimmer for grass): the fuel filter is carefully changed, without leaving an open suction pipe. Whether the replacement of the air filter is needed, it is possible to determine if the engine with the air purifier removed is launched. Whether it is necessary to change the grid on the fuel supply, if the lawn mower is not started, a dry candle will tell.

Sapun, a hole for air intake into a gas tank. If it is clogged, discharge is created in the tank and the mixture does not enter the carburetor. The hole can be blown with air or cleaned with a needle. Clean the exhaust channel, remove the anti.icper mesh of the muffler.

What to do if the engine does not start?

If the lawn mower fails is not possible, then the first thing is to check the presence of fuel in the tank and its quality. For refueling the tool, it is recommended to use high-quality gasoline purchased at gas stations, the brand of which should not be lower than the AI-92. Savings on cheap fuel can lead to a breakdown of the cylinder-piston group, for the repair of which a third of the cost of Motokosa itself can take. It is equally important and correctly preparing a fuel mixture of gasoline and oil. The proportional ratio of these components of the mixture is indicated by the manufacturer in the manual. Do not prepare the fuel mixture in large volumes, since during long storage its properties are lost. It is better to use a freshly prepared mixture.

When preparing the fuel mixture, pour the oil into gasoline using a medical syringe that allows you to accurately observe the necessary proportion of the components

Ozito 18V Cordless Grass Trimmer Tips & Tricks

Fuel filter pollution in the tank may also prevent the operation of the lawn mower engine. Therefore, when problems with the launch of the motor, check the condition of the filter. If necessary, replace the filter. It is forbidden to leave the incoming pipe without a fuel filter.

The air filter also needs to be in the test. During contamination, the part is removed, in the field is washed in gasoline and put in place. In the country or at home, the filter can be washed in water using detergents. After that, the filter rinses, squeezes and dries. The dried filter is moistened with a small amount of oil used to prepare the fuel mixture. Excess oils are removed by compressing the filter with hands. Then the part is installed in place. The removed cover is placed back and fixed with screws.

The air filter washed in the fuel mixture, squeezed and dried, is installed in place in the plastic case and covered with a lid

How this procedure is done in more detail you can look at

If all of the above procedures are carried out, and the engine is not started, then adjust its revolutions at idle, twisting the carburetor screw. In the video posted at the beginning of the article, attention is paid to this issue.

  • Put the tool on the side so that the air filter is at the top. With this location of the chainsaw, the fuel mixture is ensured exactly into the bottom of the carburetor. On the first attempt, the engine will start if you remove the air filter before starting and pour a few drops of the mixture into the carburetor, and then install the dismantled parts to the place. The method is tested in practice.
  • If the first advice does not give a result, then, most likely, the problem in the spark plug. In this case, unscrew the candle and check its performance, as well as dry the combustion chamber. A candle that does not show signs of life, replace the new.
  • If the spark plug is in good condition, the filters are clean and fuel mixture, then you can use the universal way of starting the engine. Close the carburetor air damper and pull the starter handle once. Then open the damper and pull the starter 2-3 times. Repeat the procedure from three to five times. The engine will surely start.

Some pull the pen with such force that it is necessary to repair the starter of the lawn mowed with their own hands. This is possible only in the case of a gust of a cable or breakdown of the cable handle. In other cases, it is recommended to replace the starter. This node is sold in the collection.

The lawn mower stalls at high speeds

Perhaps the most common complaint related to gasoline trimmers sounds like this: “The lawn mower stalls”.

Of course, the reason for this may be a rather serious malfunction. However, most often the situation is much simpler than it seems at first glance.

To cope with such a problem, first of all, try to deal with its causes on your own, because, having found out the reason, it is much easier to fight the problem, and sometimes it is even self.destructive.

In fact, the reasons are when the lawn mower stalls at high speeds, there are quite a lot of these reasons.

Another, this is the presence of malfunctions in the power system.

In this case, the lawn mower will stall at idle. The problems with the power system may lead to a drainage or incorrect carburetor adjustment.

Vibrations that take place in the process of operation of the lawn mower can lead to a reservoir.

Incorrect adjustment of the lawn mower can be fixed by simply adjusting it in accordance with the requirements specified in the operating instructions.

In addition, sometimes gasoline trimmers for grass can stall due to the fact that the valve located in the gas tank cover just clogged or stick.

To find out, try using a braid by loosening the gas tank cover.

If in this mode the device works properly, clean the valve.

over, the lawn mower can stall due to poor fuel flow into the carburetor

Why then the device starts up, ask you?

The reason for this is that at first the fuel gradually falls into the carburetor and is enough for work with increased power.

However, then it is produced and at large speeds the engine begins to stall.

As for the carburetor, here the problem may also be that its body is too pulled.

The reason that the lawn mower stalls at high gas speeds may also be an air leak.

We are talking about the possible presence of a place through which air can pass during the heating process of the engine.

Among other things, do not forget to check the fuel intake hose. The problem may be that it is weak or cracked at all.

At high speeds

The hole in the fuel cover (saepun) of a trimmer for grass

With a similar problem, it is worth paying attention to the fuel valve, which, when clogging, ceases to normally pass the fuel mixture. By solving this malfunction, it is weakening using a suitable tool

In addition, the problem with the circulation of the fuel mixture may cover in the contamination of the valve. To do this, just blow it with a stream of compressed air.

  • etching of atmospheric air into the combustion chamber;
  • problems with the circulation of a mixture of fuel;
  • clogging the saapun in the lid of the fuel tank (cleaning the hole with a thin sewing needle);
  • Incorrect carburetor adjustment.

When air sunses, when I operate ICE, it is necessary to check the tightness of the pipes and the integrity of the gaskets in the CPG. The problem with the circulation of the fuel mixture can be solved by the elimination of blockages in the fuel pipes leading to the carburetor. If a vacuum occurs in the tank and not receipt of the fuel mixture to the carburetor, it is enough to clean the soundtress with a thin needle and blow it with air.

If the lawn mower stops when pressing the gas, then the reasons may be the following.

  • The most common option is a fuss of adjusting the carburetor, which occurs with significant loads on the drive, after a prolonged inaction of the mechanism or when it is used in severe conditions.
  • The clogging of the fuel valve, which eliminates it with the message, as a result of which gasoline according to the system begins to flow normally.
  • The weakening and hanging of the cable in the carburetor. Also, a tensile of the fuel hose can occur up to its rupture, caused by the action of a significant load.
  • Clogging of the saapun (check valve), as a result of which fuel does not enter the tank.

If the problem is associated with the carburetor node, then it can be recognized by the appearance of vibrations of the lawn mower. Когда лопается шланг или растягивается трос — выполняют замену данных комплектующих.

When a braid for grass stalls at high speeds, this is due to the following problems:

  • clogging or clutching a valve located on the gas tank lid;
  • The carburetor was diluted under the influence of vibrations arising during the operation of the mechanism;
  • problems with the circulation of the fuel mixture;
  • atmospheric air
  • The hose intended for fuel fuel cracked or slightly connected.

The carburetor is regulated by relying on the operational instruction to the trimmer. For configuration, it is often enough to weaken the tightening of its body. If there are problematic issues with the circulation of the fuel mixture, then it can gradually enter the carburetor. After its production, the engine stalls at high speeds.

  • a clogged air damper;
  • The clogged filter is fuel, and when you give gas, this is especially noticeable;
  • the air of the crankshaft shaft occurs;
  • damaged gasket between the cylinder and the carb.

When you cleared, washed and blowing the elements, but again the lawn mower stall when you press the gas-replace them with new ones, check the quality of the fuel, as well as the literacy of the proportions of the cooked mixture. When opening the air damper, the tool will stall for the following reasons:

  • Dosage carburetor.
  • The appearance of cracks on the fuel hose caused air leaks.
  • The occurrence of problems with the oil seals.

Read more: The best robots-vacuum cleaners of 2021: 10 flagship ratings

In the process, situations arise when the lawn mower at high speeds is subject to a similar sharp stop. It occurs for the following reasons:

  • due to problems with the circulation of the fuel mixture;
  • with air leaks;
  • The fuel intake hose is poorly connected or cracked and cannot be used;
  • stab or clogged the valve of the cover of the gasoline tank;
  • The carburetor was resolved.

What in the end

It is worth noting that the inconsistency of the idle move on the engine with the injector is diagnosed by the method of checking the main systems that are responsible for the flow of air in the internal combustion engine, also a change in the composition of the consistency, taking into account the number of incoming air. It turns out that it should also be taken into account that the failure of individual sensors of the ESUD can lead to an increase or floating turnover of xx.

The lawn mower stalls at high speeds

Perhaps a more common complaint associated with gasoline trimmers sounds like this: the lawn mower stalls.

Naturally, a rather formidable malfunction may be a prerequisite for this. How to adjust the carburetor at idle does not work. On the Forward Boistorose, even at idle (the benzotrimmer shaft always turns even on. The lawn mower stalls at idle. The Benzotrimmer system and the lawn mower system does not work. But almost always the situation is even easier than it seems in the 1st look.

To cope with such an inconsistency, at first, try to deal with its causes without the help of others, because, having found out the reason, it’s even easier to fight with the inconsistency, and at times it is even self.destructive.

In fact, events are when the lawn mower stalls at high speeds, there are quite a lot of these events.

Another is the presence of flaws in the power system.

In this case, the lawn mower will stall at idle. For what reasons Stihl 100 eighty stalls idle or complete gas at least some kind of tool can break and the Stihl MS 100 chainsaw is not an exception. The lawn mower does not work at idle. The problems with the power system may lead to a drainage or incorrect carburetor adjustment.

If the chainsaw of STIHL MS 100 eighty stalls at idle, does not gain power when pressed on gas or completely stalled at full speed, you need to diagnose the fuel system and inspect the crankcase for density. You can do this without the help of others, but you need to have certain abilities. If you are not familiar with two.stroke saws, it is better to turn to specialists, t. To. This technique is quite capricious and any errors are expensive.

The lawn mower stalls at high speeds

Perhaps a more common complaint associated with gasoline trimmers sounds like this: the lawn mower stalls.

Naturally, a rather formidable malfunction may be a prerequisite for this. I can’t get a trimmer for grass why when working a motor for but saw, with all this, it does not revolve? It works only when it is worth opening its trimmer for the grass does not work right away. On the suction. It works only when opening an air damper for one mm I do not think that a trimmer for grass but. But almost always the situation is even easier than it seems in the 1st look.

To cope with such an inconsistency, at first, try to deal with its causes without the help of others, because, having found out the reason, it’s even easier to fight with the inconsistency, and at times it is even self.destructive.

In fact, events are when the lawn mower stalls at huge turns, there are quite a lot of these events.

Another is the presence of flaws in the power system.

In this case, the lawn mower will stall at idle. Works only at idle. trimmer for grass actually new. This may be exclusively in case I can’t start a trimmer for grass Craton works on a sucker. Stalls, mm for two. And she doesn’t work. If the engine at idle why the motor works. The problems with the power system may lead to a drainage or incorrect carburetor adjustment.

Why does the lawn mower stall when you press the gas: the causes and their solutions. The lawn mower stalls (trimmer for grass): on idle.

  • Idle sensor failure;
  • Clogging of the throttle;
  • The failure of the throttle position sensor;
  • Injector or carburetor pollution

The grounds for breakdown can be completely different, therefore, when eliminating them, it will be necessary to operate with all kinds of actions and techniques. If your shoulders are considerable driver’s experience, and you know the features of the car’s work as your five fingers, regardless of the model, then the elimination of this kind of malfunctions will not cause you any problems. And all because such breakdowns are not complex or serious. It follows that you can establish the operation of the car without outside help. Well, if the level of awareness or lack of free time will not give you the opportunity to eliminate all defects yourself, it is better to seek help from knowledgeable people who can save you from unpleasant moments in the shortest possible time.

| Denial of responsibility | Contacts |RSS