Trimmer for grass gasoline no power reason. The lawn mower stalls hot? There is a solution!

The trimmer for the grass does not gain momentum. the causes of the problem and their elimination

Why is the gasoline or electric trimmer for STIHL, Husqvarna, Champion grass is not gaining momentum. why do this common problem have a number of different reasons for the trimmer. While working with the device, you can meet as obvious problems, signs

Trammers for grass are reliable and durable (of course, subject to proper care). Most often, malfunctions arise due to contamination of structural elements.

If the engine of your lawn mower does not start, does not gain momentum, does not reach the power you need or suddenly stalls, it may be a reason:

  • low.quality fuel (fuel mixture), it can be in long.term storage or in non.compliance with the recipe for the preparation of the mixture;
  • The grass was wound on the shaft of the fishing/knife head;
  • clogging of the air filter/muffler;
  • Balance of the carburetor.

The lawn mower stalls

When purchasing a lawn mower, you must be prepared for the fact that, as in all other similar tools, breakdowns may also appear in it that will require repairs.

But do not immediately run to the service center and pay big funds to the craftsmen who convince you of the presence of severe malfunctions in the device.

The lawn mower stalls at high speeds

Perhaps more and more a widespread complaint associated with gasoline trimmers sounds like this: “The lawn mower stalls”.

Naturally, a rather harsh fault may be a prerequisite for this. A two.stroke trimmer engine for grass does not develop turns stalling. lawn mower FS 130 give gas stalls. But in most cases, the situation is even easier than it seems to be the 1st gaze.

In order to cope with such an inconsistent, first, try to deal with its causes without the help of others, because, having found out the reason, it’s even easier to fight with the inconsistency, and from time to time it is even self.destructive.

In fact, circumstances, this is when the lawn mower stalls at high speeds, there are quite a lot of these circumstances.

Why is a Chinese lawn mower not developing momentum?

The trimmer for grass does not gain momentum, a very common inconsistent and of course does not always have a common solution.In this.

The lawn mower is not gaining momentum, the cause of the malfunction and eliminate it

1st launch of the latest lawn mower.Removed the grid from the silencer, began to work.

Another, this is the presence of malfunctions in the power system.

In this case, the lawn mower will stall at idle. At speed stalls a trimmer for Champion grass. GAPHOLLOSKALL GOODLUCK 4300 stalls video revolutions. The lawn mower stalls when you press the gas. At high speeds, the lawn mower stalls. The problems with the power system may lead to a drainage or incorrect carburetor adjustment.

Vibrations that take place in the process of operation of the lawn mower can lead to a reservoir.

Incorrect adjustment of the lawn mower can be fixed by simply adjusting it in accordance with the requirements specified in the operating instructions.

In addition, sometimes gasoline trimmers for grass can stall due to the fact that the valve located in the gas tank cover just clogged or stick.

To find out, try using a braid by loosening the gas tank cover.

If in this mode the device works properly, clean the valve.

The reasons

Trammers for grass are reliable and durable (of course, subject to proper care). Most often, malfunctions arise due to contamination of structural elements.

If the engine of your lawn mower does not start, does not gain momentum, does not reach the power you need or suddenly stalls, it may be a reason:

  • low.quality fuel (fuel mixture), it can be in long.term storage or in non.compliance with the recipe for the preparation of the mixture;
  • The grass was wound on the shaft of the fishing/knife head;
  • clogging of the air filter/muffler;
  • Balance of the carburetor.

Ways to eliminate problems

The first three reasons are quite simple to eliminate. If the matter is the mixture, it is necessary to pour old fuel from the tank, prepare a new emulsion from high.quality gasoline and engine oil (if your motor requires a mixture) and pour it into a fuel tank. If a trimmer for grass works on clean gasoline, it’s still easier.

In the second case, it is necessary to carefully release the details of the trimmer for grass from the wound grass.

If the filter is clogged, you can try to rinse it. If this procedure has not brought the effect, replace it with a new.

The last reason why the lawn mower does not work properly will require you a little more knowledge and skills.

In order to properly adjust the carburetor of the lawn mower, it is necessary to observe a certain procedure. First of all, carefully clean the air filter. The easiest way to rinse it (it is advisable to carry out the filter with water regularly after 9-10 hours of operation).

After that, in the diagram of your trimmer for grass, which is in the instructions for the operation of the device, find the adjustment screws. Usually there are three of them: the first is responsible for the supply of fuel, the second. for idle, but the third is designed to limit the number of maximum engine speeds.

trimmer, grass, gasoline, power, reason

Next, you should turn on the unit and wait for the engine to warm up.

Slowly twist the first adjusting screw (fuel mixture). Catch the moment when the motor begins to stall, and turn the screw in the opposite direction 45 degrees. If you did not have time and the motor stalled, the screw should be turned 90 degrees. Open the throttle and see how the speed is going. Next, you should slowly unscrew the screw (each turn. the same 45 degrees) until the moment when, with full gas, the motor begins to firmly issue maximum revolutions.

The second screw, as mentioned above, controls the engine speed at idle. Weakening it, you reduce the number of revolutions, tighten. increase. The screw must be adjusted so as to ensure confident operation of the motor at small speeds. Accelerate the engine for better starting a little. At the same time, make sure that before the movement of the knives/coil with the fishing line, the motor makes several dozen revolutions. With poor starting the engine, screw the screw slightly.

After you have adjusted the first two screws, test the operation of the device at the maximum engine speed. If necessary, you can limit it (maximum). this will serve as protecting the motor from “boiling”. To do this, you need to do the third screw. Unscrew the fixation nut until the moment when the control screw can be calmly turned. To increase the maximum speed, the screw must be loosened to reduce. on the contrary, tighten. Fix the screw position with a nut. Test the work of the motor again.

Spend the position of the screws regularly. a high level of vibration characteristic of benzocoses can cause their involuntary shift.

Remember that carburetor adjustment is not the final procedure. During operation, Motokos, most likely, you will have to mess with it more than once, because an unbalanced carburetor is both an increased fuel consumption and a quick failure of the candles, not to mention reducing the power and productivity of the device.

At high speeds

When a braid for grass stalls at high speeds, this is due to the following problems:

  • clogging or clutching a valve located on the gas tank lid;
  • The carburetor was diluted under the influence of vibrations arising during the operation of the mechanism;
  • problems with the circulation of the fuel mixture;
  • atmospheric air
  • The hose intended for fuel fuel cracked or slightly connected.

, based on the operational instruction to the trimmer. For configuration, it is often enough to weaken the tightening of its body. If there are problematic issues with the circulation of the fuel mixture, then it can gradually enter the carburetor. After its production, the engine stalls at high speeds.

trimmer, grass, gasoline, power, reason

At idle

At single speeds, the common reasons for stopping a trimmer for grass are as follows:

  • reducing the speed of the gearbox when heating it, which is a consequence of the use of inappropriate fuel mixture;
  • clogging of the throttle;
  • air entering the system;
  • not enough fuel for the operation of the lawn mower.

If a carburetor is a problem place, then the technique will stop at the “cold” and with a “hot” launch.

The trimmer for the grass is very hot

Overheating of a trimmer for grass can occur for many reasons:

  • Gasoline has not the same octane number indicated in the instructions for the unit;
  • the proportions of gasoline and oil during the preparation of the fuel mixture are not observed;
  • A mixture of fuel with butter has long been prepared (the mixture cannot be stored for more than 2 weeks);
  • The trimmer for the grass works more than the time instructions;
  • A low.power trimmer for grass on thick and hard grass is used, the device works with overload and quickly heats up;
  • shifted towards the bar or the cassette lid clutched.

The latter occurs if you install a mowing head inappropriate for this unit, or when the axis shifts inside the bar. These changes make it difficult to rotate, the load on the engine increases, and it overheating.

The main thing is the fuel mixture!

In this case, the remains of plastic plastic dissolved in the brutal environment are created in the combustion chamber so terrible things that you will definitely not be able. But you certainly remember how to correctly store fuel.

What to do when the fuel was definitely ordinary, there is a spark, but a trimmer for grass does not start a gasoline? It is possible that you just flooded the candle with gasoline. In this case, it must be turned out, wiped with a clean rag and dry. In general, when a trimmer for the grass began to act up and stall why a trimmer does not start for grass. By the way, it will be completely useful to check the candle for performance itself.

The gasoline trimmer for the grass does not gain momentum what problems

This all.produced task has a number of different circumstances.

At one time of working with the device, you can meet with obvious problems, the signs of which are correctly tracked, and with asymptomatic options. The 1st option is more simple from the point of searching for difficulties.

If the trimmer for grass does not develop, and there are no exact signs of breakdowns, then you will need to alternately check more common cases of problems, and if the prerequisite is detected, remove it.

Non.disclosure, when the lawn mower does not develop, is mainly found in gasoline engines. This is tormented by the technique of different models, for example, Husqvarna, Champion, Stihl.

With high.quality products, such problems are more frequent than with cheap ones from unknown manufacturers.

Part of the structural parts with which difficulties will be associated are available to visual examination, to verify the functioning of other components it will be useful to disassemble the motorcycle.

How To Fix a Generator That Won’t Put Out Power

The trimmer for the grass does not develop momentum if refined with low.quality fuel. Therefore, the engine may not start or work with “jerks”, changing the speed of rotation of the knife or fishing line.

To find the quality of gasoline used without the help of others, subsequent deeds are made.

  • The candles are removed with a special key.
  • Inspect their working contacts for the presence of a rabid brick color plaque: if it is of course, then the fuel used contains significant inclusions of the additives.

Candles in general often act as indicators that allow you to find problems with the combustion chamber of the internal combustion engine, since of course they can be quickly removed and look around.

If plaque is detected, you need to drain fuel in a tank and replace it with a high.quality. The gas mower used should be refuel only with those brands of gasoline, which are indicated by manufacturers in the operating annotation. Also, the candles should be cleaned from plaque before installing to the place.

The subsequent all.fought prerequisite for lowering the number of revolutions on the trimmer is the pollution of its air or fuel filters. At the beginning, the inconsistent is that the fuel-air mixture entering the combustion chamber is not saturated with oxygen, and therefore not all the gasoline burns. This does not allow Motokos to develop the highest power.

Pursuing the purpose of checking whether the air filter really will indulge, it is necessary to remove it (for previously promoting the cover for this purpose) and turn on the lawn mower. If it works fine, then the knocked.down filter element is knocked down you need to stick a new.

If the situation remains unchanged after the actions done, then it is necessary to study the fuel filter.

Fix a Mower that stopped while mowing and won’t start again

The essence of difficulty is similar to a previous case, only a bidding of oxygen does not work than gasoline for the usual operation of the device. The elimination of this task is also carried out by the usual change in the filter element.

Air and fuel filters are cheap. It is not difficult to change them without the help of others, and all the work does not take extra time.

It should be noted that without a fuel filter, it is forbidden to operate a trimmer for grass by annotation, and a piston knot is useful to repair a piston node through a kutser.

With the invariable operation of the lawn mower, the spark plugs are polluted and wear out over the years. To check this, they are removed and inspected for the presence of a carbon. Of course, remove the problem with 2 methods: with the ability, return an old candle, or simply set in its place the latest.

  • turn and wiped a candle from a fuel;
  • dry it without calcination;
  • Using a file or small sandpaper, they remove from a candle of crochets and inspect the gap between the electrodes (occurs 1 mm);
  • collect a trimmer for grass;
  • Book a lawn mower.

The main reason does not develop in the chainsaw of the lawn mower

If the candle does not give out a spark after restoration manipulations at a suitable distance between the electrodes, then you will need to check the quality of the units of the parts of the electronic circuit of the device. Когда с проводами полный порядок, то пригодится совершенно точно устанавливать новейшую деталь.

Changing candles is a light process that is inexpensive, if you can return old ones, then in general free of charge. Only the candle key and the superstil will come in handy for the work.

If there is a constant red pollution and wear of the candles, then it is necessary to find the case of these abnormal phenomena deeper.

If with fuel, filters and candle of ignition to our client remains in order, then the subsequent source and possibly an internal combustion engine. He will have subsequent mechanical breakdowns:

There is a small cable in the carburetor department. He can save and lead to the dilemma under consideration. Therefore, while engaged in a carburetor, you should first check the condition of the cable, and if you want to tighten (however, not up to the maximum). The main thing is not to overdo it with a stretch so that he does not crack under load.

After it is necessary to check the operational options of the carburetor, which are made to comply with the characteristics given in the annotation. If they are installed correctly, but there is no suitable effect, then you should disassemble the part, wash, clean, blow the pump what remains to make our client and collect it back. The carburetor itself is expected without mechanical damage.

Read Stihl lawn mower how to refuel a fishing line for a trimmer

If it is impossible to independently restore the performance of the carburetor, it is better to replace it with the latest detail or resort to expert services.

If the passage, when the adjustment or change of the carburetor does not give the desired result, you need to clean the drive mechanism and grease the cable with oil.

The problems associated with the engine can be removed at home with the required abilities, but it is better to use the services of the service center for this purpose. Its specialists will conduct an all.encompassing diagnosis of a trimmer for grass and establish an exact cause of the speed of revolutions.

Violation of conventional circulation of fuel on the trimmer also leads to the fact that the lawn mower does not gain working turnover. This is possibly caused by such basic reasons:

If everything is in order with electrical equipment, then we check the carburetor.

Vacuum carburetors are put on trimmers for grass. When disassembling it, cleaning or washing, it is necessary to be as careful as possible under any circumstances to disassemble the lower part of the carburetor where the primer is located. Air filter (it is visible if you remove the protective casing from the carburetor) must be washed with detergents. The most ideal for washing dishes. After drying, put back. We wash the carburetor with unsented gasoline and blow out all the holes by the pump. We also wash the filter of the gas pipeline, then we dry everything and collect everything. Usually, after all manipulations, the trimmer for the grass begins to work.

A narrow cable is made of fishing line, it is worth placing it on a motorcycle?

This idea comes to mind in virtually everyone who had to pump out 10 acres overgrown with the highest grass. On the 1st gaze thought seems good. The cable is stronger than the fishing line, it is not so wear out. But not everything is so simple.

Also, the ignition coil can be broken in electric equipment. In this case, the lawn mower will not start or start and works with interruptions, and later stalls, or it will not start on the hot at all.

You can check the serviceability of the coil in the same way as when checking the spark: we unscrew the candle, lean it against the trimmer body for the grass. If there is no spark when the starter is jerking, or it occurs after once you need to change the coil.

The lawn mower is not gaining momentum, the cause of the malfunction and eliminate it

.Removed the grid from the silencer, began to work.

Another, this is the presence of malfunctions in the power system.

will stall at idle. At speed stalls a trimmer for Champion grass. Hoodluck lawn mower four thousand three hundred stalls at speeds. The lawn mower stalls when you press the gas. At high speeds, the lawn mower stalls. The problems with the power system may lead to a drainage or incorrect carburetor adjustment.

Vibrations that take place in the process of operation of the lawn mower can lead to a reservoir.

Incorrect adjustment of the lawn mower can be fixed by simply adjusting it in accordance with the requirements specified in the operating instructions.

In addition, sometimes gasoline trimmers for grass can stall due to the fact that the valve located in the gas tank cover just clogged or stick.

To find out, try using a braid by loosening the gas tank cover.

If in this mode the device works properly, clean the valve.

Air or fuel filter pollution

The next common cause of reducing the number of revolutions on the trimmer is the pollution of its air or fuel filters. In the first case, the problem is that the fuel-air mixture entering the combustion chamber is not saturated with oxygen, as a result, gasoline does not burn out all. This does not allow the maximum power to develop a motorcycle.

In order to check whether the air filter is really to blame, you need to remove it (first promoting the lid for this) and turn on the lawn mower. If it works fine, then instead of a clogged filter element, you must insert a new.

Read how to lubricate a gearbox of a gasoline trimmer for grass

If the situation has not changed after the actions done, then you need to pay attention to the fuel filter. The essence of the problem is similar to the previous case, only instead of a lack of oxygen is a little gasoline for the normal operation of the device

The elimination of this problem is also carried out by a simple replacement of the filter element. Air and fuel filters are inexpensive. It is easy to change them on their own, and all the work does not take much time.

It should be borne in mind that without a fuel filter, it is forbidden to operate a trimmer for grass, otherwise you will need to repair a piston node after a short time.

Engine starting problems

It is very important to determine the cause of the failure correctly, because otherwise we simply cannot eliminate it. If there are no extraneous sounds when trying to set up a chainsaw (knocking down, grinding, etc. D.), It often turns out that in fact there are no problems

For example, if you put the chainsaw and pull the fork for a long time, the engine simply pours and starts very much

D.), It often turns out that in fact there are no problems. For example, if you put the chainsaw and pull the fork for a long time, the engine simply pours and starts very much.

To properly start the engine saw engine, install the lever or switch to the “flap” position. Then you need to pump the mixture into the carburetor if there is a fuel pump in stock. Pull out the starting handle until the engine resistance becomes noticeable, and energetically extend the amplitude, taking your hand to the side. After two. Three such movements, the engine must first start, and then decay. If this does not happen, then it is necessary to transfer the lever to the position of half.gas or simply to the working position, and then continue to work the chainsaw in this mode. Many Pologaz chainsaws are recorded automatically when the air damper is pulled

Some models have an ignition with the key, it is important to make sure that it is turned on

If the engine does not start, the first thing to do. unscrew and check the spark plug. There are times when the plant fills the burner with fuel in the cold season. Then you also need to unscrew the candle, dry the combustion chamber with one plant, clean the spark plug, screw it up and repeat the start. It is advisable to immediately check the presence of a spark. On a twisted candle, we put on a cap with a high.voltage wire, we put it on a cylinder, and we pull the starter. Visually observe a frequent blue spark. OK. We twist the candle in place and launch it. If there is no spark, change the candle and repeat the attempt. Again, no. Check the connection of the high.voltage wire to the spark plug, coil and ignition system.

In general, the condition of the candle can be used to determine the type of malfunction.

  • Dry. Most likely, the fuel mixture is not included in the cylinder. This is not a ignition system, so the candle is screwed and checked.
  • Wet, strongly sprinkled with fuel. The cause of the excessive fuel mixture is to violate the launch rules, as described above, or if the carburetor is incorrectly set up.
  • Covered with black carbon. This may indicate the use of poor.quality oil, an incorrectly configured carburetor or an incorrectly calculated ratio of gasoline and oil. The candle should be washed, cleaned of carbon deposits with a sharp object (awl or needle), rub the electrodes with a fabric and installed in place.

When checking the light of the ignition, it is necessary to pay attention to the gap between the electrodes: Normal is considered from 0.5 to 0.65 mm. Damaged or worn gasket should be replaced. Correctly adjusted carburetor chainsaw provides its effectiveness at full capacity with the most economical fuel consumption

Correctly adjusted carburetor chainsaw provides its effectiveness at full capacity with the most economical fuel consumption.

The need for tuning a carburetor chainsaw is infrequent, since adjustment is originally performed by the manufacturer to achieve the optimal mode of operation. Adjusting screws are designed for a more accurate adjustment of the carburetor chainsaw, if necessary.

Among the causes of violation of fixing the adjusting screws are the most common:

  • Strong vibration or damage to a protective cap. This rarely happens, but still happens.
  • Serious engine wear (piston). Of course, in this case it is better to take care of repairing a chainsaw, but at the same time, adjusting the carburetor can improve its functionality for some time.
  • Litter in a carburetor because of the low quality of gasoline or due to the formation of scale. In this case, in addition to adjusting the carburetor, it can be avoided.

The reasons

Trammers for grass are reliable and durable (of course, subject to proper care). Most often, malfunctions arise due to contamination of structural elements.

If the engine of your lawn mower does not start, does not gain momentum, does not reach the power you need or suddenly stalls, it may be a reason:

  • low.quality fuel (fuel mixture), it can be in long.term storage or in non.compliance with the recipe for the preparation of the mixture;
  • The grass was wound on the shaft of the fishing/knife head;
  • clogging of the air filter/muffler;
  • Balance of the carburetor.

Immediately after you started

The unit can stall immediately after the launch, if the carburetor is cesspool or was incorrectly configured. this causes Uneven fuel supply

The result is that the device begins to vibrate clearly. To eliminate problems, the carburetor is reconfigured, acting according to the instructions for the mechanism.

The engine also stops when Clotting of the valve

, supplying fuel. In such cases, it is enough just to clean it. If the lawn mower at first earned, but then immediately stalled, then possible fuel to the carburetor unit enters some difficulty. The weakening of the valve helps to solve the issue, which provides free circulation of the mixture in the system.

The stop may also be called Air suction

In the presence of mechanical damage to the hose (holes, cracks) that fuel fuel fuel. In this case, the drive should be added to the drive to quickly drive air bubbles from the system.

When to contact the workshop

If the device is under warranty, at the first signs of incorrect operation, it can be safely attributed to a specialized workshop. Repair will be made for free, regardless of the nature of the damage, if it happened not due to the fault of the owner. In case of breakdowns in the engine, an ignorant person in technology, it is better to immediately contact a specialist. In any case, the degree of seriousness of malfunctions with the unit is determined by the user himself.

Summarize. Both gasoline and electric trimmers for grass are designed for many years of reliable work. Most of the problems described above occurs due to the insufficient attention of the owner to his assistant. Subject to strict compliance with the requirements from the manufacturer and regular maintenance, the manual mower will work rhythmically and without interruptions.

For what reason does an electric braid for STIHL grass do not develop full power

When using an electric trimmer for the grass, non.aviation problems may also occur. Here the reasons are completely different than that of fuel cos.

You can eliminate problems yourself

Eletric trimmer for grass does not develop the required power, because:

  • The voltage in the network is below the required minimum for the device more than 10%;
  • There was a failure on a smooth launch (if there is such a system);
  • there was a malfunction of the brush node;
  • The engine winding was burned;
  • rotating parts sometimes jamming.

To establish voltage, you should first check its power. If it does not meet the norms, it should be increased using a stabilizer.

The repair of the smooth start system is carried out only in the service center.

With wear of brushes, you just need to replace them. When installing new ones, it is recommended to clean all the surfaces with which they contact.

To establish voltage, you should first check the power.

When burning engine windings, you need to change the electric motor.

Jamming of parts of rotation can occur for various reasons. To eliminate them, you should review the entire drive unit.

The last problem may also arise in another unit of this company. the STIHL prisoner, and the sharpening of the disk on the scissors will be its solution.

| Denial of responsibility | Contacts |RSS