What can be done by a end saw. Carpet manufacturers rating

End saw or circular: what to choose?

Many people believe that the saws, despite the name, are similar to each other and are easily able to replace each other in work. However, this is not quite true. Each tool has its own purpose, a number of tasks that it is able to solve, so we advise you to choose the right device.

The replacement of the saw is often sinful by novice masters who have not yet studied the clear purpose of a particular tool and do not use them in certain tasks. Explain this is simple: the working body of both devices is a round disc. At its core, the end. The same circular, but fixed with the help of a mobile mechanism above the bed.

Before buying, we advise you to familiarize yourself with the appointment of each of them and choose the one that is most responsible for the tasks.

Areas of the use of manual and stationary models

The end saw is an electric manual tool designed for sawing and processing various materials (wood, metal and plastic). Depending on the purpose, such equipment is classified as follows: end and end and traffic control, pendulum and circular saw (electric stupid).

The manual disc saw differs from the end saw only in that it does not have a bed with a rotary table, which makes it more mobile, and this is especially important with domestic use.

Top saws on wood are used for sawing wooden blanks, as well as products made from woodworking products (laminate, wood-steering plate, wood-fiber plate and other slab materials). Sprinking is performed at a straight or other specified angle or inclination, which is necessary in the manufacture of carpentry and furniture items. In addition, such equipment is used in the implementation of construction and installation and finishing work.

Using manual disc saw when processing a wooden balance

Manual models are used on construction sites and at home, and stationarily installed. In the conditions of workshops or workshops of various types of production. Pendulum saws are used when working with metal, which is necessary in the manufacture of metal structures in various fields of production. Such equipment is installed stationary, and special saw discs are used to work.

Device and functionality of the end saw

The end of the end is not difficult to understand from the figure on which the main components of the tool are indicated. Everything else is only additions that do not change the principle of work, but only improve functionality and ease of use.

Handle with a power button.2. Saw disk.3. Protective casing.4. Clamp for fastening the workpiece.

Stops for the workpiece.6. The mechanism of fixation of the table at a given angle.7. Horizontal angle adjustment scale.Eight. Table.

Vertical angle adjustment mechanism.Ten. Vacuumber.Eleven. Engine.12. Pension for carrying.

The main elements of the end saw are an electric motor and a saw disk manufactured from high.Quality over.Strength steel. Engine, saw disc and connecting them with a functional unit, is also located a handle with a switching room.

The entire block is attached to the base. The bed, on which the sawing workpiece is placed. On the basis of the rotary circle moving when setting the angle of cut, and the emphasis. The beds of relatively expensive devices are made of strong and light aluminum or magnesium alloys, which ensures not only the reliability of the base, but also the mobility of the entire tool due to weight loss.

The functional block is connected to the bed through a rotary lever using a spring.Loaded hinge. The rotary lever is called the pendulum, and the end of this type of endoenthes themselves. Pendulum.

The pendulum provides the movement of the working module. To perform the cut, it is necessary to lower the lever, “drowning” the saw disk in a fixed workpiece (there is a slot for unhindered sawing in the turning circle of the bed). This is the most just option for the end saw. As a rule, all modern models are equipped with a mechanism that provides the rotation of the desktop along with all mechanisms, in a horizontal plane.

Thus, guides and table elements remain motionless, and the tool itself changes the position in the horizontal plane. Using such a tool gives more ending opportunities.

Daws of the combined type have another hinge that allows you to rotate the lever relative to the vertical axis (t. E. Such cuts can be changed in two planes). Often, the turn around the horizontal axis is allowed only in one direction. The opposite of the electric drive.

But there are models that allow you to tilt in both directions.

10 Famous Clothing Logos With HIDDEN Meaning | RMRS Style Videos

Such technical solutions repeatedly expand the list of tools of the tool. Cutting, tilted to the vertical, allows you to handle the blanks of which the height is greater than the active radius of the disk.

Install Vinyl Plank or Laminate WITHOUT LOSING Your Mind | Here’s How

The cutting width of the end saw is relatively small, especially when working at an angle or slope. For example, an average pendulum saw with a 10-inch disc at a right angle cuts a beam of 95 × 95 mm or a board of 69 × 135 mm (when you install any other angles, the permissible size of the workpiece decreases). In other words, the end saw is unsuitable not only for the longitudinal saw, but also for the transverse sawing of wide blanks.

To increase the cut width, the saw is equipped with a traction function. The working unit at the end with such a function is moved not only around the axis of the hinge, but also along the cut line along the guide rods, due to which the maximum width of the cut at an angle of 90 ° increases from 80-180 mm to 280-340 mm. Such tools are called end saws with a length or saws with horizontal movement.

In this case, the mechanisms implementing the movement of the saw along the workpiece differ depending on the manufacturer and the model of the device.

Vorskla PMZ-90-255

Recently managed to test such a saw a little. Despite the style of the name (fashionable now), a purebred Chinese appeared before me, in a sense analogue LS 1040.

The feeling from this end, as if you transplant from a foreign car to the Zhiguli-it seems to go, but somehow it is not very good. The most important thing is the backlash in the settings, so the high accuracy of the cut is simply unattainable. The details of the engine body and the control button are rudely made, well, that’s okay, if only it does not break. The protective casing interferes a little to work (it was removed by the owner). The engine is powerful. 2100 watts, which is as much as 450 watts more than Makita, it is at the same speed (4500 about./min.). It works louder, but not more productive, heated well. It requires regular breaks. Sawdust stubbornly fly past the vacuum cleaner. The presence of a long mechanism is pleasing, you can cut the workpiece somewhere around 30 widths. True, the console moves tight. There is no smooth start, there is no disc brake after turning off. Otherwise, everything is tolerable. It’s still difficult to say something about the durability of this device, since the copy has not yet been really checked in battle.

If the PMZ-90-255 does not sprinkle under load, you can recommend it as an option for home use, where superiority is not needed, and the speed of the saw is at the forefront. The price of such a machine is about 170–180, that is, instead of Makita LS 1040, you can buy two and a half Vorskla PMZ-90-255.

How to use a end saw

When the saw is chosen, it must be configured. Then she will be ready for use. Should act according to the rules. And you need to figure out how to control the tool depending on the processed material.

On wood

A trigger switch is used for launch. But the tool will not start performing cuts until the lock lever is pressed. After that, the equipment is lowered to the material. Before work, it is recommended to put on protection products to protect yourself from chips that will appear when processing wood.

The wooden workpiece should be held with your hand if the cut occurs at right angles. But if the work is performed by a newcomer, it is recommended to use the clamp. It holds the material motionless, allowing you to focus on the cut. The clamp is necessarily needed if they work with blanks not at right angles, but at any other.

To adjust the cutting angle, it is necessary to use the platform reversal. It is necessary to unscrew the handle acting as a turning lock, and squeeze it down. The platform is ready to move.

Attention! When changing the angle, the sawing area increases. This reduces the convenience of using a saw, so it is necessary to use clamps.

To change the angle of cutting of wood, you can use the vertical inclination of the end. The fixation handle is first weakened, set the desired slope and fix it again.

For metal

Before turning on the tool, it is necessary to make sure that its nodes and the capabilities of the disk are free to move. To carry out the oblique saw, it is necessary to loosen the mounting screw at the rotary table and start turning it to the desired angle. The set position is immediately fixed. If the work is long, periodically, you should check how accurate the ending is. This is due to the fact that after some time there is a weakening of the mounting screw.

If you need to saw with the left inclination, then it must be configured correctly. The mounting screw of mounting the inclined angle is released and the desired angle is set. To fix the installed parameter, the screw is tight. After that they continue the saw.

Important! When the work is finished, after turning off the tool, you must wait for the cutting disk to completely stop. After that, the handle returns to the position up.

It is forbidden to remove a protective casing from the device. It rises when the disk is lowered down for the saw.

How to use a end saw

When the saw is chosen, it must be configured. Then she will be ready for use. Should act according to the rules. And you need to figure out how to control the tool depending on the processed material.

On wood

A trigger switch is used for launch. But the tool will not start performing cuts until the lock lever is pressed. After that, the equipment is lowered to the material. Before work, it is recommended to put on protection products to protect yourself from chips that will appear when processing wood.

The wooden workpiece should be held with your hand if the cut occurs at right angles. But if the work is performed by a newcomer, it is recommended to use the clamp. It holds the material motionless, allowing you to focus on the cut. The clamp is necessarily needed if they work with blanks not at right angles, but at any other.

rating

To adjust the cutting angle, it is necessary to use the platform reversal. It is necessary to unscrew the handle acting as a turning lock, and squeeze it down. The platform is ready to move.

Attention! When changing the angle, the sawing area increases. This reduces the convenience of using a saw, so it is necessary to use clamps.

To change the angle of cutting of wood, you can use the vertical inclination of the end. The fixation handle is first weakened, set the desired slope and fix it again.

For metal

Before turning on the tool, it is necessary to make sure that its nodes and the capabilities of the disk are free to move. To carry out the oblique saw, it is necessary to loosen the mounting screw at the rotary table and start turning it to the desired angle. The set position is immediately fixed. If the work is long, periodically, you should check how accurate the ending is. This is due to the fact that after some time there is a weakening of the mounting screw.

If you need to saw with the left inclination, then it must be configured correctly. The mounting screw of mounting the inclined angle is released and the desired angle is set. To fix the installed parameter, the screw is tight. After that they continue the saw.

Important! When the work is finished, after turning off the tool, you must wait for the cutting disk to completely stop. After that, the handle returns to the position up.

It is forbidden to remove a protective casing from the device. It rises when the disk is lowered down for the saw.

Electric end.Saw: nuances and selection criteria

The question of how to choose a end saw can be solved by adhering to five small rules.

    First you must decide on its purpose and operating conditions. Why do you need it? What work, and most importantly, in what quantity do you plan to make it with its help? If you purchase a pipe for home use and do not plan to perform complex operations, then you can do a simple tool with the basic configuration of additional functions. If we are talking about the professional use of the end saw and its daily use, then, of course, you need to choose an extended version of this tool with a full set of additional features. You can consider the option of purchasing the so.Called combined end saw, which is equipped with an additional desktop in the upper part of the cutting head, allowing it to be used as a stationary circular saw.

Naturally, making the choice of a end saw, it will not be superfluous to take into account the power of this tool, as well as the speed of rotation of the disk. In most cases, these values ​​are designed by the manufacturer and are optimal. In a household tool, the power will be lower than that of a professional, but the speed of rotation of the disk is almost always the same, which is caused by the need to make a clean and even cut.

rating

What is the end of the end for

The main task of the ending is to make a very accurate and perfectly even cut at a given angle. It can be a horizontal saw at 90 ° or at an angle of 30 °, 45 ° and so on. Most often, a end saw is needed at woodworking and furniture enterprises, often its use in finishing work. She is an indispensable assistant in the manufacture of door and window openings, furniture. The endings have found their application and where you need to work with polymer materials or soft non.Ferrous metals. For this, they have a saw disk replaced with a cutting disk for metal. Sometimes the end saw is called the installation, because it is directly involved in the installation of something.

If you do not need to frequent use of the end or the accuracy of the cut should not be so critically accurate, then we recommend paying attention to the cheaper and simple disk saw.

rating

Disks for the end saw: what is the difference between them

There are not so many differences between the discs used on the end saw. The main of them is planting and external diameter, as well as the geometry of the cutting tooth. If with the size of the disks more or less understandable (the landing hole can be either 25mm or 30mm, and their outer diameter is 210, 250 and 305mm), then the tooth geometry should be understood in more detail.

  • Attention should be paid to the size of the tooth. The larger it is, the rougher the cut. A large tooth disk is unlikely to be purely cutting laminated, lacquered or painted blanks. For these purposes you need to purchase a disk with a small tooth. Also, a small tooth showed itself well when working with an aluminum profile. In general, in this regard, saw wheels for the end saw can be divided into three types: for longitudinal cuts, for transverse and for final cuts, which, as a rule, are universal.
  • If we are talking about mass production or working with thick blanks, you need to pay attention to the presence of thin slots on the disk. In fact, these are temperature compensators, the tasks of which include maintaining a stable disk when it is heated. In addition, such discs are less noisy.

And a few words about enterprises that produce end saws on wood. The leaders in the production of almost all electric tools are Bosch and Makita, and their end saws are no exception. Metabo, Hitachi, Dewalt tools also showed themselves well in practice. If we talk about domestic end saws, then here we can note the Corvette tools. In general, there is something to choose from. The main thing is not to count with the possibilities.

Here, in principle, and all that you need to know regarding such an instrument as the end saw. Buy, use it and remember that this tool is quite dangerous. Do not forget about safety precautions and be always extremely assembled when working, and most importantly sober!

| Denial of responsibility | Contacts |RSS