What can be screwed in with an electric screwdriver. Making holes for planting
What can be made of an electric screwdriver
In addition to the standard use of an electric screwdriver in repair and construction work, many craftsmen make from it household appliances, equipment for various purposes. Often, modifications and tips for using the tool greatly simplify the life of the user. The pluses also include a significantly lower cost and a long service life of created devices in comparison with their factory analogues. The following will tell you what you can make from an electric screwdriver at home.
A small PVC boat can be launched with the machine. In this case, the watercraft will not be able to reach high speed, but such a solution will be suitable for leisurely walks on the water or fishing during a dead calm period. The device obtained from an electric screwdriver, many people call an “electric paddle”.
To install the motor from a cordless tool on the boat, you need to take or cut out a metal impeller, in which you drill a hole with the diameter of a meter metal stud. The latter is clamped with nuts and inserted into an electric screwdriver, allowing the propeller to move.
The resulting boat motor is fixed on the watercraft with improvised materials (clamps, homemade stands). The easiest way is to hold the machine with your hands.
With a propeller diameter of 100 mm, the boat takes 3 min. the wrench can travel approximately 100 meters.
You can use plastic or metal brushes to strip surfaces of old paint and polish metal parts of car bodies for priming or painting. Even has a brush nozzle that can be used to quickly clean a toilet bowl. Some brushes have an hex shank like a standard electric screwdriver bit, but others may require an adapter.
DRILL VS. DRIVER (What’s The Difference?!! Cordless Drill Vs. Impact DriverCOMPARISON)
Metabo BS 18 LTX Impuls
Hammerless type model allows you to drill 13 mm holes in metal and 65 mm in wood. Considering that the craftsman will often use the drilling function, the manufacturer has equipped the device with a 2-position speed slide switch. It allows you to set the chuck speed to 500 or 1700 rpm. In addition, the set includes a chuck for bits and a quick-action chuck for drills for use with various types of attachments. The torque of 110 Nm is sufficient for screwing screws up to 150 mm in length.
The device has a brake of the engine that stops it almost instantly after releasing the power button. LED backlighting for working in dimly lit areas. The motor is protected from overload. It should be noted that the device is equipped with two high-capacity 5.2 Ah batteries, which are enough for several hours of uninterrupted work. But such a high-capacity battery has affected the weight of the unit. with it it weighs 2.3 kg, which is significantly more than with the previous screwdrivers. The manufacturer supplies a 3-position handle and storage case with the electric screwdriver.
The Japanese have created a really cool machine that can handle any fastener and drill a hole in any material of any density. Has an impact mode to make screwing in long fasteners as fast as possible and to minimize drilling resistance. Electric screwdriver drill is equipped with a quick-action chuck capable of working with drill bits for wood, metal and concrete. It is able to make a hole up to 76 mm in diameter in wood, up to 13 mm in metal and up to 16 mm in concrete. If you need to drill holes for installing door frames into the opening, this is the right device.
the electric screwdriver has a powerful brushless motor with a torque of 115 Nm. And you can adjust the screw-in torque with a 21-position switch. The speed is also adjustable in two positions: 550 and 2100 rpm. Additional handle and drilling depth gauge included. It makes it possible to drill just the right spot, for example for a plastic dowel cap. Also, the unit is equipped with two 5 Ah batteries each. On average, one battery lasts for 4 hours of work, and its charging, according to the manufacturer, will not last longer than 45 minutes. an electric screwdriver is quite expensive, so it is worth buying it only if you regularly do “odd jobs.
Milwaukee M18 FPD-502X
Once you have worked with a Milwaukee power tool, you will never want to change over to any other tool. The quality of work performed, ease of use, power, reliability. these are just some of the positive qualities of Milwaukee M18 FPD-502X. Maximum torque of 135 Nm. which allows it to turn long screws and even drill holes in the ice. On average, you can drill up to 40 m of ice with the 130 m drill on one battery pack (according to user reviews). One of the main uses is drilling holes, which the unit is able to perform the following parameters: 16 mm in metal, 16 mm in concrete with the mode of impact, and in wood up to 89 mm.
Brushless motor with brake and electronic overload protection. It comes with two 5 Ah batteries with an average charging time of 59 minutes. Note that all M18 series batteries are suitable for the model, that is, if you have other handheld power tools of this series, the batteries will fit. For convenient drilling, the manufacturer supplies an additional handle, the position of which can be changed under the left- or right-handed person. It costs a lot of money, but it pays for itself quickly. If you have a construction crew and your electric screwdriver will be used by several people, then this device from Milwaukee is the right one. But for home use it is better to get something cheaper.
How to remove the bit correctly
To increase the speed of work, you also need to know how to remove the nozzle from the electric screwdriver. To quickly unscrew the bit, use “reverse” mode. Then fix the chuck and start the machine. This loosens the clamping jaws and you can easily remove the bit.
It is not uncommon for craftsmen to have a question about how to remove the bit from an electric screwdriver if it is jammed. It can get stuck in any type of chuck for the following reasons:
- large amount of debris, scale under the shaped frequent jaws;
- Fixation in the holder of tooling, the size of which is larger than allowed;
- poor quality material or overheating of the nozzle.
In such situations, the tool can not work. There are several ways to help you remove a stuck element yourself, but if you lack the necessary knowledge, it is better to have the problem solved by a service center.
Experts recommend pulling out the drill bit or bit only after thoroughly lubricating the chuck with WD-40. In this case, the element must be removed and then the grease poured in until it flows over all the cams. After 15 min. the tool holder is clamped in a vise, the jaws are tapped with a hammer (better a rubber one), a cloth or a wooden bar is put underneath. When the grip on the jaws loosens, the bit can easily be unscrewed.
If it is not possible to achieve a positive result, the chuck can be heated with a hair dryer.
Sometimes craftsmen use adjustable wrenches to remove the tool. One clamps the chuck, and the other gently unscrews its upper part. The use of soft, thin, but dense shims prevents damage to parts.
The drill has an adjusting ring to set the torque, on which its values are marked.
This is necessary in order to set the most suitable value when working with materials of different hardness.
For example, for screwing self-tapping screws into drywall (with little effort), the range of values 2-4 is suitable, and for hard wood, the torque can be set to the maximum number on the ring.
This setting helps to avoid rapid damage to the fastener slots.
RPM can be varied by increasing or decreasing the amount of force applied to the trigger.
This allows you to stop the tool in time when the screw or bolt is fully tightened.
How to use
The answer to the question of how to use an electric screwdriver is quite simple, the main thing is to carefully follow the instructions for use, especially in the first stages of learning a new tool.
The battery must be stored in its protective case at all times. It is best to put away charging, metal objects, to avoid short circuit of opposite contacts and its failure.
The battery is inserted simply by inserting it into the appropriate groove on the bottom of the handle of the electric screwdriver and pushing it in until it clicks into place. To remove it, press the buttons on both sides of the battery and pull it out at the same time.
How to attach the bit or drill bit
You must place the back of the bit in the middle between the cams that clamp it. After that, clamp the sleeve of the electric screwdriver with one hand and turn it on with the other, this will tighten the cams, and secure the bit or drill inside.
To remove the bit, the mechanism is the same, but you have to switch the electric screwdriver to reverse rotation and remove the bit.
Depending on what kind of screwdriver is used and what material it is screwed into, the amount of force the electric screwdriver applies to the fastener head will vary. At the top there is a switch with different numbers, which mean the force in Newtons.
AWESOME DIY TIPS. HOW TO USE A DRILL/ SCREWDRIVER COWBOYDIY.COM
It can be difficult for beginners to find the right mode right away, for example:
Screwing in and out the screwdriver
Initially, the tool is in the neutral position. The mode switch is usually located near the trigger.
The switch may look different, but the principle is the same: it can be in reverse, neutral, and clockwise.
Important! Hold the electric screwdriver correctly when screwing or unscrewing.
It should be positioned perpendicular to the plane of the material to be worked with. To screw in self-tapping screws, a small amount of force should be applied so that the device can enter the material. When using it instead of an electric screwdriver, it is better, on the contrary, to do everything carefully without a strong push to avoid unnecessary breakage.
Tips for women to use an electric screwdriver
It is not always possible for a man to attach or unscrew fasteners in the house. Interest in how to use an electric screwdriver often arises among women. First of all, experts recommend choosing a light and compact model.
Then you need to read the instructions, which describe how to twist with an electric screwdriver fasteners in materials of different density to achieve the desired result. After studying the rules of adjustment, installation of nozzles, the woman should not forget that the use of the machine requires physical strength. It is better to hold the tool with both hands when working and to be extremely attentive.
Do not forget about the rules of safety:
- only start working after the machine has been set up and the right nozzle has been installed;
- Avoid getting liquids, sand, construction dust and shavings inside the chuck;
- Do the operation in a well-lit room;
- Clean and lubricate the riveting chuck periodically;
- Wear protective working clothes and safety glasses.
If a woman plans to use the tool often, it is better to know in advance how to untwist an electric screwdriver. This will ensure proper maintenance of the machine, avoiding numerous breakdowns.
The riveting adapter
The riveting adapter from the reputable Chinese manufacturer DEKO. A compact and convenient nozzle is quite a worthy alternative to a riveting gun. The design is equipped with a noise protection. Ergonomic design ensures complete safety and comfortable grip. Suitable for a variety of materials: wood, aluminum, stainless steel. Supplied with four optional bits 3/32″,1/8″,5/32″,3/16″. Is compatible with a tool that has a rotor speed of at least 1000 rpm./min.
Wire Twisting Bit
A simple nozzle that allows you to strip and twist a few wires at the same time, speeding up the process significantly. Made of high-carbon steel, galvanized. Is a small bit 902010 mm, one side has holes with a blade for stripping and twisting wires, and on the other side is a hex shank for fastening the bits into the chuck. No more than five wires of a minimum cross section of 2 wires can be stranded at the same time.5 to 4 kV. mm.
- Replacing nickel cadmium batteries in an electric screwdriver
- How to put a cartridge on an electric screwdriver. Hitachi tool
- How to remove a battery from an electric screwdriver. How to disassemble the battery of an electric screwdriver
- How to disassemble an electric screwdriver Redverg. Methods of fastening