What is the best way to cut a plastic skirting board?. Sawing corners of skirting boards

What to cut a plastic baseboard: tools and equipment

Baseboard is a necessary part of a room’s interior, and no living room can do without it. Most coatings can not lie close to the wall, in connection with that, the seam between the wall and the surface adjacent to it will inevitably have a rather unsightly appearance. Installation of wooden, plastic, metal skirting boards. it is quite a simple process, which is quite realistic to carry out with their own hands, without resorting to the services of specialists.

In the recent past the main material for the production of baseboards was natural wood, but in view of the significant disadvantages, the most noticeable of which were high price and excessive stiffness, the most rational was the use of plastic floor panels. PVC skirtings are much cheaper than their wooden counterparts and are highly flexible, allowing for a more efficient installation process.

As in any other case, the installation of the plastic skirting has a number of specific features, among which occupies a special place the process of cutting the panels, which is necessary for the formation of angles or linear connections. PVC panels have a flexible hollow structure. the traditional way of cutting is not suitable for them, as a conventional wood saw will leave an uneven cut edge and create splinters.

Correctly cut corners ceiling plinths. the appearance of the future construction. Uneven cuts, chips and poorly fitting seams will adversely affect the visual impression of the panels as a whole, the interior of the room in particular. This article will provide you with instructions on how to properly cut plastic panels.

Types of ceiling and floor plinths, choice of tools

Installation of baguettes and baseboards is no less important stage of repair than any other. And trimming corners here is the most difficult. It is important to choose the right tool for the job and the most appropriate way to cut.

Skirting boards

Ceiling moldings, also known as moldings, fillets, borders or just a skirting board, are mostly used for finishing joints between the wall and ceiling, but sometimes they are used to cover inner corners, make decorative frames or panels, and design niches and architectural elements. There are several of the most popular materials for making ceiling moldings:

Plastic (polyvinylchloride). It is more convenient to cut wide and rigid moldings with a metal hacksaw. If a more gentle tool is needed, a jigsaw is used.

best, plastic, skirting, board, sawing, corners

Styrofoam (polystyrene foam). A very light and porous material that is best cut with a sharp construction or office knife.

Wooden baguettes. Slant-ground saws specially designed for baguettes are suitable for cutting. Hand or electric jigsaws can also be used.

Floor plinth

Modern floor plinths can hardly be called a plank that closes the gap. It is a structural component that complements the design and accentuates the overall design. Baseboards are made of several materials:

The wooden ones can be made of massif or veneer. For trimming use flat or circular saws, jigsaws.

Plastic skirting boards are “dangerous” competitors to traditional wood. Easy to install and cut with an ordinary metal hacksaw.

Aluminum skirting boards. the last word in interior design. Usually cut through with an electric saw or a handheld metal saw.

Only on wooden baseboards will have to do a corner trim. The rest are trimmed evenly and joined with special corners.

Now you have an idea of how to properly cut ceiling baseboards in the corners. The video in this article will help you reinforce the material you’ve learned (see “How to Trim a Baseboard with a Baseboard” on CD).(See also the article “Corners for ceiling plinths: types, material selection and measurement of the room and installation work”).

If after studying you still have questions, put them in the Комментарии и мнения владельцев, we are happy to help.

Exterior corner of the wooden strips.

The necessary tools and calculation of quantity of materials

Every self-respecting owner should have a well-equipped tool kit in his arsenal, which will come in handy in many situations. But, in the case of finishing the room with baseboards, without additional equipment can not do. Depending on the method of fixing the baseboard, the following tools and materials may be needed for the work

  • A tape measure (measuring);
  • a pencil;
  • A cutter (for making holes in concrete walls);
  • screwdriver (drilling in wooden materials or drywall);
  • An angle grinder or a hacksaw (for cutting the skirting boards);
  • clips;
  • Self-tapping screws with dowels;
  • Assembly glue or liquid nails;
  • acrylic sealant.

To determine the necessary amount of materials, it is necessary to perform the appropriate calculation. First of all, the perimeter of the room in which you plan to install the baseboard is measured. In this case, the width of the doorway can be ignored. To determine the number of plastic profiles, divide the resulting value by the length of one slat.

The number of connecting corners is comparable to the number of walls in the room. Two plugs per door. To determine the number of fasteners (self-tapping screws or staples) should divide the perimeter of the room (in meters) by 0.5 m, but it is better to take with a reserve.

best, plastic, skirting, board, sawing, corners

Alternative to standard types

The right tool will not leave jagged edges

Bathroom design in a hruschevka: a competent approach and features

After the PVC skirting board is cut, there must not be any chips on the edges. The right tool, which will have to cut the baseboard canvas, does not cause cracks or significant irregularities on the edges of the edge.

The electric jigsaw is no less popular with builders, but it can only be used when working with panels. Skirting boards, whose feature is quite thin walls, can not be cut qualitatively with such a device.

Sharp stroke and quite large teeth will lead to the cracking of the product, making it impossible to install.

The safest and most effective after a hacksaw for metal is recognized an ordinary mounting (wallpapering) knife.

Cutting thin skirting boards, which are fastened to the floor, with such a tool is done quickly and easily enough.

The easiest way to cut PVC skirting boards equipped with a trunking is with a standard handjigger. It will allow you to make a precise cut, keep edges intact and prevent cracking of the skirting board.

Cut the trim, covering the cable-channel, must be prepared after the skirting board itself. When it is cut to the exact size, you must install a blanking plate, and only then cut it, too.

Baseboard fitting starts at the far inner corner. If the length of the wall is long, then it is necessary to use a connecting plug, and then cut the skirting board, not reaching 1,5 cm to the edge of the wall or 0,5 cm to the next corner. Regardless of the number of corners and connections, cutting is carried out strictly in a straight line, which greatly facilitates the work. For a detailed tutorial on cutting and joining baseboards, see this

How to cut a plastic skirting board?

Baseboards are an indispensable part of the interior of any room, of course, when it comes to residential areas.

Although not uncommon, and those cases where, without appropriate final processing, which just happens to be the installation of skirting, even an austere office space looks incomplete.

The fact is that most floor coverings do not lie close to the walls, so there are unsightly seams from the outside, the concealment of which is the main task of the skirting boards.

Choosing the right tool

The first and quite logical question that arises in every person who plans to install baseboards. why cut it? It is from the tool you choose that directly depends on how smooth the cutting edge will be.

The thing is that PVC products are hollow, so using tools with large teeth or a wide wave is not recommended for cutting them, because it can end up with chipping and numerous irregularities.

I recommend the best option. a hacksaw for metal. Its teeth are quite fine, and the width of the separation is just acceptable for work with PVC.

But here it can be used only for panels, as thin-walled skirting boards can not withstand the impact of the teeth, and the cut at the end acquires an uneven appearance.

If you need to cut corners on a ceiling plinth, you can easily do this with a hand jigsaw.

The resulting cut will be perfectly equal, whatever the plastic product in question.

Naturally, this tool also has a disadvantage. small dimensions, due to which the work with large blades of material will take a long time.

I want to draw your attention to the fact that when working with a jigsaw is highly recommended not to use circular saws with abrasive, as they only complicate the entire process. For example, a clear and straight cut can only be made if you have some experience with such tools and materials

For example, a clean, even cut can only be made with some experience with these tools and materials.

Step by step instructions for cutting with the chisel:

A tray in the middle of the plinth cutter is used to hold the skirting boards in place.

The panel must be placed against the fixture with the rough surface, because if put the opposite way, the cut can damage the front part.

The aforementioned diagonal slots are placed in such a way that they act as guides for the cutting part.

The next step is to select the right angle. It is worth taking care that the edges of the panel do not protrude beyond the edges of the guide rails. Only then can you get a quality cut.

If the width of the used baseboard is narrower than the tray in the jig, you have to press the panel evenly to one side of the groove and only in this position make the cut.

It is possible to place the panel at any angle in the tray, because later the shapes are not identical with each other. PVC has a rather elastic structure, which is why it is better not to put pressure on the skirting board during sawing, as the cut will be uneven.

You should also not speed up the cutting process yourself, as this will cause the edges to overheat and deform.

After sawing one side of the corner, you can proceed to the other, but with only one difference. the second corner will be the mirror opposite of the first. To make a straight cut, there is a perpendicular notch on the jigsaw that allows you to cut strictly vertically.

How and what to cut a plastic baseboard. 3 of my favorite ways

The question of how to cut plastic baseboards can be answered quite concisely and unambiguously, pointing to a hacksaw for metal, but it will still not be quite accurate information. After all, by and large, there is an implication in this question, indicating the complete action and not the tool itself, so without a complete familiarity with the process, the purpose of this or that tool is difficult to understand. Therefore, I want to tell you about my own experience, gained over the years of practice, and in addition you can watch the video in this article.

Tools and appliances

With the arrangement of the final framing of the floor, any home handyman reasonably have three main questions:

Sawing long products into individual pieces of the required length can be done with the help of:

The final choice of what to cut the plastic skirting board with, depends on the already available tools, personal preferences and experience.

To securely fix the fillets to the walls of the room, you will need:

  • a torch (with a drill of the required diameter) or an electric drill (with percussion mode of operation);
  • a set of dowels and self-tapping screws;
  • screwdriver or an electric screwdriver (to save time and effort).

For accurate sawing of pieces at the right angle will have to buy a plier (of course, if it is not in the household). Without it there is no way.

How to cut plastic baseboards

Choosing what to cut a plastic baseboard, give preference to a familiar and fairly easy to handle tool. We are talking about a metal saw, familiar to all craftsmen.

However, this is not enough, because it is required not only to accurately make a straight cut, but also to accurately and correctly cut the corners.

To qualitatively perform this operation, you need such a device as a joiner’s plier. It is the one that can be used to cut a 45 or 90ͦ angle. Of course, you can use an angle grinder, but in this case the cutting line for the trimmer will be quite wide, which is not always convenient.

Completing the repair and finishing work in the room, every specialist asks the question “what to cut the plastic baseboard”. The answer depends on how important the quality of the resulting edge is.

The highest quality it will be when using a hacksaw for metal. Its blade is thin and strong enough, so the cut will be thin and even. The edges will not crumble, and it will be convenient to cut the skirting board.

If the quality of the edge is not particularly important, but the speed of the work is important, then many builders and finishers use an angle grinder.

How to Cut & Install Skirting Board, Baseboard Internal Corners

The thickness of its disc is such that the cutting line for the trimmer will be quite wide, but the edges will not always be able to please the owner with its quality. However, with the help of this tool, it is possible to perform quite a large amount of work in a short time.

An angle grinder will leave a smooth edge

Even a metal scissor can be used to cut a skirting board if you have no other tool at hand. This manipulation can not be called convenient, but if necessary, the master can easily cope with the task.

In any case, the cutting tool must meet certain requirements, among which are:

Use a particular device should be used after you are convinced of its productivity and the possibility of quality work.

The right tool does not leave jagged edges

After a PVC skirting board has been cut, the edges should not have any chips. The right tool, which will have to cut the baseboard cloth, does not cause the appearance of cracks or significant irregularities on the edges of the.

No less popular with builders electric jigsaw, but it can only be used when working with panels. Skirting boards, whose feature is quite thin walls, can not be cut qualitatively with such a device.

A sharp stroke and quite large teeth will lead to cracking of the product, making it impossible to install.

A standard wallpapering knife is considered the safest and most effective after a metal saw.

Cutting thin wall baseboards, which are attached to the floor, with such a tool is fairly quick and easy.

PVC skirting boards that are equipped with a cable duct, the easiest way to cut them is with a standard hand jigsaw. It will allow you to make a clear cut, keep the edges intact and prevent cracking of the plank.

Cut the plank that closes the cable-channel, it is necessary after the preparation of the skirting board itself. When it has been cut to size, a blanking plate should be installed, and only then should it be trimmed.

Baseboard installation starts with the far inside corner. If the wall is long, you have to use a joint cap and then cut the skirting board 1.5 cm short to the edge of the wall or 0.5 cm to the next corner. Regardless of the number of corners and joints, cutting is carried out strictly in a straight line, which greatly facilitates the performance of the work. For a detailed guide on how to cut and join baseboards, see this

Beginners often ask how to cut a ceiling plinth to properly form an inside or outside corner. Ceiling baseboards cannot be accurately cut without a wire cutter. This device allows you to make a cut at any desired angle.

Proper trimming is possible with strict adherence to geometric shapes. Using a straight edge band saw produces a perfectly straight and precise cut.

perfect inside miter joint hack. baseboard molding install

Working diagram with a wire cutter

The full set fixture has grooves designed for cutting workpieces at an angle:

To perform the operation, during which it is necessary to install a baseboard in a corner, you will need to cut the panel strictly at 45 ͦ. In this case, two parts stacked together will give a full 90 ͦ when creating both external and internal corners. For more information on how to properly saw out the baseboards with the necessary angle, see this

Cutting any baseboard (ceiling or floor) is done after determining the correct slope.

The configuration of the corner itself determines the location of the cut on the inside or outside surface of the part.

In cases where the walls in the room are uneven and there are almost no strict angles, it is not worth using a jigsaw. It is better to cut the skirting boards by hand, using a normal painting knife (stationery knife).

How to run a wire under a baseboard

What to seal the gaps between the floor and the wall

Installing skirting boards with cable ducts

| Denial of responsibility | Contacts |RSS