Why did a trimmer for the grass began to work poorly. How to get a motorcycle stihl

The trimmer for the grass does not gain momentum. the causes of the problem and their elimination

Why is the gasoline or electric trimmer for STIHL, Husqvarna, Champion grass is not gaining momentum. why do this common problem have a number of different reasons for the trimmer. While working with the device, you can meet as obvious problems, signs

Trammers for grass are reliable and durable (of course, subject to proper care). Most often, malfunctions arise due to contamination of structural elements.

If the engine of your lawn mower does not start, does not gain momentum, does not reach the power you need or suddenly stalls, it may be a reason:

  • low.quality fuel (fuel mixture), it can be in long.term storage or in non.compliance with the recipe for the preparation of the mixture;
  • The grass was wound on the shaft of the fishing/knife head;
  • clogging of the air filter/muffler;
  • Balance of the carburetor.

The lawn mower stalls

When purchasing a lawn mower, you must be prepared for the fact that, as in all other similar tools, breakdowns may also appear in it that will require repairs.

But do not immediately run to the service center and pay big funds to the craftsmen who convince you of the presence of severe malfunctions in the device.

The lawn mower stalls at high speeds

Perhaps more and more a widespread complaint associated with gasoline trimmers sounds like this: “The lawn mower stalls”.

Naturally, a rather harsh fault may be a prerequisite for this. A two.stroke trimmer engine for grass does not develop turns stalling. lawn mower FS 130 give gas stalls. But in most cases, the situation is even easier than it seems to be the 1st gaze.

In order to cope with such an inconsistent, first, try to deal with its causes without the help of others, because, having found out the reason, it’s even easier to fight with the inconsistency, and from time to time it is even self.destructive.

In fact, circumstances, this is when the lawn mower stalls at high speeds, there are quite a lot of these circumstances.

Why is a Chinese lawn mower not developing momentum?

The trimmer for grass does not gain momentum, a very common inconsistent and of course does not always have a common solution.In this.

The lawn mower is not gaining momentum, the cause of the malfunction and eliminate it

1st launch of the latest lawn mower.Removed the grid from the silencer, began to work.

Another, this is the presence of malfunctions in the power system.

In this case, the lawn mower will stall at idle. At speed stalls a trimmer for Champion grass. GAPHOLLOSKALL GOODLUCK 4300 stalls video revolutions. The lawn mower stalls when you press the gas. At high speeds, the lawn mower stalls. The problems with the power system may lead to a drainage or incorrect carburetor adjustment.

Vibrations that take place in the process of operation of the lawn mower can lead to a reservoir.

Incorrect adjustment of the lawn mower can be fixed by simply adjusting it in accordance with the requirements specified in the operating instructions.

In addition, sometimes gasoline trimmers for grass can stall due to the fact that the valve located in the gas tank cover just clogged or stick.

To find out, try using a braid by loosening the gas tank cover.

If in this mode the device works properly, clean the valve.

What could break

Malfunctions with a benzocosa associated with the fact that this device is not started, in a certain way are classified by specialists of service services. They stand out malfunctions with the following nodes of the mechanism:

  • the engine in which the piston and bearings can be worn out or fail to crack the crankcase;
  • the fuel supply system, while it is possible to clog the filter or problems with the carburetor;
  • mechanical damage to wires, tubes, hoses;
  • The ignition chain.

Loving the new stihl trimmer #lawn #fyp #foryou #grasstok #Shorts

To correctly determine the knot where the breakdown occurred, it is necessary to pay attention to the circumstances of the trimmer stalls for the grass.

Ways to eliminate breakdowns

Subsequent work is likely on the carburetor:

  • cleaning and adjustment of the fuel supply valve;
  • similar work with a valve producing redesigned gases and pairs (after burning fuel);
  • replacement of the spring more weak on the entrance valve;
  • restoration of the tension of the carburetor cable;
  • replacement of the fuel leaks hose, verification and strengthening of a weakened connection;
  • changing the rotor damper disk;.
  • Change of faulty wire or ignition coil.

Immediately after the start

Smelting Motokos or a trimmer for the grass after starting is justified by subsequent reasons:

  • impressive of previously adjusted valves;
  • first the wrong settings of the valve mechanism;
  • clogging with deposits of the fuel supply valve;
  • the hose is worn or poorly annexed.

Due to the violated method of injection of a fuel, a lawn mower or a trimmer for grass is very vibrated in work.

Ways to eliminate problems

The first three reasons are quite simple to eliminate. If the matter is the mixture, it is necessary to pour old fuel from the tank, prepare a new emulsion from high.quality gasoline and engine oil (if your motor requires a mixture) and pour it into a fuel tank. If a trimmer for grass works on clean gasoline, it’s still easier.

In the second case, it is necessary to carefully release the details of the trimmer for grass from the wound grass.

If the filter is clogged, you can try to rinse it. If this procedure has not brought the effect, replace it with a new.

The last reason why the lawn mower does not work properly will require you a little more knowledge and skills.

In order to properly adjust the carburetor of the lawn mower, it is necessary to observe a certain procedure. First of all, carefully clean the air filter. The easiest way to rinse it (it is advisable to carry out the filter with water regularly after 9-10 hours of operation).

After that, in the diagram of your trimmer for grass, which is in the instructions for the operation of the device, find the adjustment screws. Usually there are three of them: the first is responsible for the supply of fuel, the second. for idle, but the third is designed to limit the number of maximum engine speeds.

Stihl trimmer won’t start or has no power? How to adjust the valves on a Stihl 4 mix. Repair Vlog

Next, you should turn on the unit and wait for the engine to warm up.

Slowly twist the first adjusting screw (fuel mixture). Catch the moment when the motor begins to stall, and turn the screw in the opposite direction 45 degrees. If you did not have time and the motor stalled, the screw should be turned 90 degrees. Open the throttle and see how the speed is going. Next, you should slowly unscrew the screw (each turn. the same 45 degrees) until the moment when, with full gas, the motor begins to firmly issue maximum revolutions.

The second screw, as mentioned above, controls the engine speed at idle. Weakening it, you reduce the number of revolutions, tighten. increase. The screw must be adjusted so as to ensure confident operation of the motor at small speeds. Accelerate the engine for better starting a little. At the same time, make sure that before the movement of the knives/coil with the fishing line, the motor makes several dozen revolutions. With poor starting the engine, screw the screw slightly.

After you have adjusted the first two screws, test the operation of the device at the maximum engine speed. If necessary, you can limit it (maximum). this will serve as protecting the motor from “boiling”. To do this, you need to do the third screw. Unscrew the fixation nut until the moment when the control screw can be calmly turned. To increase the maximum speed, the screw must be loosened to reduce. on the contrary, tighten. Fix the screw position with a nut. Test the work of the motor again.

Spend the position of the screws regularly. a high level of vibration characteristic of benzocoses can cause their involuntary shift.

Remember that carburetor adjustment is not the final procedure. During operation, Motokos, most likely, you will have to mess with it more than once, because an unbalanced carburetor is both an increased fuel consumption and a quick failure of the candles, not to mention reducing the power and productivity of the device.

Features of the work of a trimmer for grass

All trimmers for grass are classified according to the type of power: gasoline or electricity (from the network or battery). It should be noted that gasoline mowers in many respects exceed their electric and battery analogues. Despite the fact that they all perform similar functions, the difference in performance, maneuverability and effectiveness is very noticeable. However, the general principle of operation of all types of manual braids is almost no different- the devices are equipped with engines (two- or four-stroke ICE or electric motors), which drive the cutting unit (reel with fishing line or metal disk). All elements are fixed on the line of straight or curved shape, including the handle for controlling the trimmer on which the main buttons are located.

Since the problem of weak revolutions is more characteristic of gasoline trimmers, they will be given more attention. So, the lawn mower is very comfortable in work and unpretentious in maintenance. over, most of its malfunctions are caused by ignorance by the user of elementary things, which are written in the instructions. Therefore, before starting the operation of the unit, it is necessary to carefully study the management of the manufacturer. In particular, in order to start the engine, it is necessary to do the following sequential actions:

  • turn on the ignition button;
  • press the silicone button for pumping gasoline several times;
  • close the air damper;
  • The gas lever is installed in a position for high speeds;
  • first make non.leaf with the starter handle to feel the engine resistance, then jerk sharply.

If the lawn mower started up, but stalled, you need to put the air damper in the middle position and repeat the attempt. When the engine works, you need to slow the gas and open the air damper, since the trimmer for the grass functions only on the leak.

Important! The mode of operation of the trimmer for the grass depends on the various environmental influences. In hot weather, the unit should be given more time to cool. When working in conditions of dense thickets or high vegetation, the engine also overheats strongly. It is necessary to take five-minute breaks every 15-20 minutes.

The trimmer for grass stalls. how to eliminate the problem

A gasoline trimmer for grass is a useful tool for cleaning from unnecessary grass of house territories and large area lawns. The design of this technique is quite complicated, therefore, if the device breaks, there may be several reasons. The most likely factors that have caught a breakdown are usually described in the user guide. Knowing why a trimmer for grass stalls, you can try to independently eliminate the defect. The most common malfunctions provoking the motorcycle stops, and the ability to repair them with your own hands is in the material further.

In order to most accurately determine the cause of the trimmer malfunction for grass of any brand (for example, echo) and find out the possibility of eliminating it, you need to install, when performing what action the device stalls. The engine can turn off both at idle and at high speeds, heated under load or immediately after starting and t.D.

If you stalled after gas supply

Owners of gasoline braids often mention that the lawn mower stalls when you press the gas. Usually such a breakdown occurs due to problems in the carburetor. A failure in his work can occur due to long-term storage, use in difficult conditions, significant overload of the motor. The symptom of such a breakdown will be vibrating movements of the device during operation.

On a note! Users familiar with the repair of a car carburetor can try to restore this important node of the trimmer for the grass on their own, using the instructions for operating. Otherwise, the correct decision will be to seek help from the service center representatives.

Sometimes a trimmer for grass stalls when you give gas because the fuel valve is clogged. This interferes with the supply of gasoline. To eliminate the problem, it is enough to loosen the valve. Thus, normal supply of carburetor fuel will be restored.

Another possible reason why the lawn mower stalls when gas is supplied is pollution of the soundtress (check valve). This detail prevents the appearance of a vacuum in a gas tank. If it is clogged, the air does not flow, which means that fuel does not go to the carburetor. To eliminate the problem, it is necessary to clean this element.

If it stalled at high speeds

If the carburetor stalls at high speeds, this means that in idle and small there are enough incoming fuel, and to work on high is not enough. Then it is necessary to check the serviceability of the following nodes of the trimmer for the grass.

  • Fuel hose. its integrity could be violated as a result of cracking. In this case, you need to replace the part. Or maybe you just need to tighten the clamps.
  • A filter network between a carburetor and a hose for supplying a gasoline mixture-it could clog. In this situation, it is necessary to clean the detail.
  • The valve on the gas tank cover. he could stick or clog with garbage. Cleaning is also necessary.
  • Carburetor. perhaps as a result of constant vibration, it was resolved. This is usually characteristic of cheap Chinese details. To eliminate the problem, it is necessary to set up according to the instructions. In some cases, it is enough to only weaken the tightening of the carburetor case. If the adjustment is not possible, it is necessary to install a new element.
  • Additionally, check the air filter. Perhaps it will need to be washed and cleaned or replaced with a new one, as he could clog with dirt and particles of grass when tilted technology, when the user mowed in hard.to.reach places.

If you stalled during work idle

If the lawn mower stalls, working idle, there may be several factors reasons.

  • First you need to check the prepared fuel solution, when it comes to a four-stroke trimmer working on a gasoline-oil mixture. There is a chance that it is made incorrectly. the proportions are not withstanded. Because of this, the gearbox is warming up, and the revolutions on the drum are lowering.
  • Another probable cause is blockage of elements such as a throttle, air filter or carburetor. You need to clean the indicated details.
  • Another possible factor is to resolve or incorrectly carried out carburetor adjustment. You need to adjust the setting according to the instructions.
  • Observe this problem mono and when opening the air damper. In this situation, the lack of fuel for a trimmer for grass occurs through the fault of the air flow.

If the device does not have enough fuel, it works properly at high speeds or when they increase, but stalls at idle. If the root of the problem consists in the carburetor, the lawn mower will be disconnected both with cold startup and hot.

If you stalled after starting

If the technique starts and stalls immediately after starting, this indicates the wrong settings or deducting the device. As a result of this, the fuel enters the engine unevenly, which leads to significant vibration and disconnecting the trimmer for the grass. To fix the breakdown, it is necessary to reconfigure the device according to the user management.

Another probable problem is the blockage of the valve supplying the gasoline mixture. It must be cleaned.

On a note! If the trimmer for the grass starts, but immediately stalls, it may also mean that the fuel is moving to the carburetor with difficulty. Weakening the valve will help to eliminate the problem. this will provide uniform and free circulation of fuel in the device.

Another possible reason is the damaged fuel intake hose. Air can penetrate through cracks and holes into the system. To solve the problem, you need to increase the engine speed in order to get rid of air bubbles that have penetrated the device.

If you stalled when opening the damper

If the technique works properly at idle, but stalls when opening an air damper, this reports about the penetration of air into the system through cracks in the fuel supply hose or damaged oil seals. To fix the breakdown and establish the work of the tool without driving air from the atmosphere, it is necessary to replace damaged parts.

Preventive measures and operating rules

So that the lawn mower does not work and does not stall when starting, it must be correctly stored and operated. Compliance with the following simple recommendations will forget about problems.

  • When begging the grass, you need to monitor the state of the cooling system. It is also necessary to regularly clean the channels in the case and starter’s ribs.
  • To clean the tool, you should use kerosene, solvent, or other washing tools.
  • You can not clean a hot tool. it must cool before washing.
  • It is important to observe the recommended working mode. this will avoid overheating of the engine.
  • If a braid for grass is not used over the next thirty days, the fuel must be drained, otherwise it will fall into heavy components that can score the channels of the carburetor.
  • After the fuel is merged, the trimmer for the grass should work at idle for some time until it turns off. This will allow you to completely get rid of the rest inside the working mixture.

To store the tool in cold weather, you need:

  • completely drain the fuel;
  • disassemble the lawn mower, wash and clean all available components;
  • inspect the condition of the parts, eliminate all defects that can be corrected;
  • pour the required amount of oil into the gearbox;
  • Clean the air filter;
  • perform partial disassembly of the engine, wash all moving parts, blow and lubricate thoroughly;
  • To lubricate the piston, unscrew the candle, then raise the piston to the upper dead point by the starter, pour a small amount of oil into the hole for the candle and do the crankshaft several times.

Important! If there is no way to store a trimmer for grass in a warm dry room, you must first wrap the motor with an embarrassed rag.

Only by observing these rules, you can be sure that the lawn mower will work properly and will not stall for a number of seasons.

As you can see, stopping the work of a trimmer for grass can be caused by many reasons. Most of them can be fixed independently using the user instructions. In cases where there is no self.confidence, the equipment is recommended to be attributed to repairs. It is worth remembering that incorrect actions can cause even greater harm to the trimmer. As a result, the repair of Motokos will cost a much larger amount than it would be initially, and in the worst case, it may be necessary to buy a new unit.

Immediately after you started

The unit can stall immediately after the launch, if the carburetor is cesspool or was incorrectly configured. this causes Uneven fuel supply

The result is that the device begins to vibrate clearly. To eliminate problems, the carburetor is reconfigured, acting according to the instructions for the mechanism.

The engine also stops when Clotting of the valve

, supplying fuel. In such cases, it is enough just to clean it. If the lawn mower at first earned, but then immediately stalled, then possible fuel to the carburetor unit enters some difficulty. The weakening of the valve helps to solve the issue, which provides free circulation of the mixture in the system.

The stop may also be called Air suction

In the presence of mechanical damage to the hose (holes, cracks) that fuel fuel fuel. In this case, the drive should be added to the drive to quickly drive air bubbles from the system.

When opening an air damper

It happens that the unit stalls when opening an air damper, working normally at idle. This is due to the air leaks of the system caused by the presence Cracks of the fuel hose

or problems with seals. The carburetor dosing system can also work malfunctioning, while the lawn mower will stop after the opening of the damper.

All possible reasons that the lawn mower stalls, and the methods of eliminating them are contained in the next video

There are many reasons for stopping Motokos, but the most commonly occur in work related to its carburetor. They can arise in any case. The most problematic option is when there is a serious breakdown, and you will need to purchase new parts or change the lawn mower.

So that the trimmer for the grass works normally for a long time, you should strictly comply with the requirements of the operating instructions. It is necessary to refuel the unit suitable for it in the composition with a fuel mixture, the device should work with a moderate load.

If everything is in order with electrical equipment, then we check the carburetor.

Vacuum carburetors are put on trimmers for grass. When disassembling it, cleaning or washing, it is necessary to be as careful as possible under any circumstances to disassemble the lower part of the carburetor where the primer is located. Air filter (it is visible if you remove the protective casing from the carburetor) must be washed with detergents. The most ideal for washing dishes. After drying, put back. We wash the carburetor with unsented gasoline and blow out all the holes by the pump. We also wash the filter of the gas pipeline, then we dry everything and collect everything. Usually, after all manipulations, the trimmer for the grass begins to work.

A narrow cable is made of fishing line, it is worth placing it on a motorcycle?

This idea comes to mind in virtually everyone who had to pump out 10 acres overgrown with the highest grass. On the 1st gaze thought seems good. The cable is stronger than the fishing line, it is not so wear out. But not everything is so simple.

Also, the ignition coil can be broken in electric equipment. In this case, the lawn mower will not start or start and works with interruptions, and later stalls, or it will not start on the hot at all.

You can check the serviceability of the coil in the same way as when checking the spark: we unscrew the candle, lean it against the trimmer body for the grass. If there is no spark when the starter is jerking, or it occurs after once you need to change the coil.

The lawn mower is not gaining momentum, the cause of the malfunction and eliminate it

.Removed the grid from the silencer, began to work.

Another, this is the presence of malfunctions in the power system.

will stall at idle. At speed stalls a trimmer for Champion grass. Hoodluck lawn mower four thousand three hundred stalls at speeds. The lawn mower stalls when you press the gas. At high speeds, the lawn mower stalls. The problems with the power system may lead to a drainage or incorrect carburetor adjustment.

Vibrations that take place in the process of operation of the lawn mower can lead to a reservoir.

Incorrect adjustment of the lawn mower can be fixed by simply adjusting it in accordance with the requirements specified in the operating instructions.

trimmer, grass, began, work

In addition, sometimes gasoline trimmers for grass can stall due to the fact that the valve located in the gas tank cover just clogged or stick.

To find out, try using a braid by loosening the gas tank cover.

If in this mode the device works properly, clean the valve.

Air or fuel filter pollution

The next common cause of reducing the number of revolutions on the trimmer is the pollution of its air or fuel filters. In the first case, the problem is that the fuel-air mixture entering the combustion chamber is not saturated with oxygen, as a result, gasoline does not burn out all. This does not allow the maximum power to develop a motorcycle.

In order to check whether the air filter is really to blame, you need to remove it (first promoting the lid for this) and turn on the lawn mower. If it works fine, then instead of a clogged filter element, you must insert a new.

Read how to lubricate a gearbox of a gasoline trimmer for grass

If the situation has not changed after the actions done, then you need to pay attention to the fuel filter. The essence of the problem is similar to the previous case, only instead of a lack of oxygen is a little gasoline for the normal operation of the device

The elimination of this problem is also carried out by a simple replacement of the filter element. Air and fuel filters are inexpensive. It is easy to change them on their own, and all the work does not take much time.

It should be borne in mind that without a fuel filter, it is forbidden to operate a trimmer for grass, otherwise you will need to repair a piston node after a short time.

Engine starting problems

It is very important to determine the cause of the failure correctly, because otherwise we simply cannot eliminate it. If there are no extraneous sounds when trying to set up a chainsaw (knocking down, grinding, etc. D.), It often turns out that in fact there are no problems

For example, if you put the chainsaw and pull the fork for a long time, the engine simply pours and starts very much

D.), It often turns out that in fact there are no problems. For example, if you put the chainsaw and pull the fork for a long time, the engine simply pours and starts very much.

To properly start the engine saw engine, install the lever or switch to the “flap” position. Then you need to pump the mixture into the carburetor if there is a fuel pump in stock. Pull out the starting handle until the engine resistance becomes noticeable, and energetically extend the amplitude, taking your hand to the side. After two. Three such movements, the engine must first start, and then decay. If this does not happen, then it is necessary to transfer the lever to the position of half.gas or simply to the working position, and then continue to work the chainsaw in this mode. Many Pologaz chainsaws are recorded automatically when the air damper is pulled

Some models have an ignition with the key, it is important to make sure that it is turned on

If the engine does not start, the first thing to do. unscrew and check the spark plug. There are times when the plant fills the burner with fuel in the cold season. Then you also need to unscrew the candle, dry the combustion chamber with one plant, clean the spark plug, screw it up and repeat the start. It is advisable to immediately check the presence of a spark. On a twisted candle, we put on a cap with a high.voltage wire, we put it on a cylinder, and we pull the starter. Visually observe a frequent blue spark. OK. We twist the candle in place and launch it. If there is no spark, change the candle and repeat the attempt. Again, no. Check the connection of the high.voltage wire to the spark plug, coil and ignition system.

In general, the condition of the candle can be used to determine the type of malfunction.

  • Dry. Most likely, the fuel mixture is not included in the cylinder. This is not a ignition system, so the candle is screwed and checked.
  • Wet, strongly sprinkled with fuel. The cause of the excessive fuel mixture is to violate the launch rules, as described above, or if the carburetor is incorrectly set up.
  • Covered with black carbon. This may indicate the use of poor.quality oil, an incorrectly configured carburetor or an incorrectly calculated ratio of gasoline and oil. The candle should be washed, cleaned of carbon deposits with a sharp object (awl or needle), rub the electrodes with a fabric and installed in place.

When checking the light of the ignition, it is necessary to pay attention to the gap between the electrodes: Normal is considered from 0.5 to 0.65 mm. Damaged or worn gasket should be replaced. Correctly adjusted carburetor chainsaw provides its effectiveness at full capacity with the most economical fuel consumption

Correctly adjusted carburetor chainsaw provides its effectiveness at full capacity with the most economical fuel consumption.

The need for tuning a carburetor chainsaw is infrequent, since adjustment is originally performed by the manufacturer to achieve the optimal mode of operation. Adjusting screws are designed for a more accurate adjustment of the carburetor chainsaw, if necessary.

Among the causes of violation of fixing the adjusting screws are the most common:

  • Strong vibration or damage to a protective cap. This rarely happens, but still happens.
  • Serious engine wear (piston). Of course, in this case it is better to take care of repairing a chainsaw, but at the same time, adjusting the carburetor can improve its functionality for some time.
  • Litter in a carburetor because of the low quality of gasoline or due to the formation of scale. In this case, in addition to adjusting the carburetor, it can be avoided.

Review

Motokosa Stihl FS38 belongs to the lighting group and is the best addition to a powerful lawn mower to record inaccessible areas along the paths, under trees and shrubs. Using STIHL mobile lawnmands, you can quickly cut soft overgrown lawns and lawns, always maintaining cleanliness on a small area.

The lawn mower stalls hot? There is a solution!

The lawn mower stalls hot-this means that there is already a certain amount of fuel for starting the engine, but after 5-10 minutes of operation, it stops working in the engine. This motor behavior indicates problems with the fuel filter.

This article will solve the case of a gas station when they stall at large gas speeds

When purchasing a lawn mower, you must be prepared for the fact that, as in all other similar tools, breakdowns may also appear in it that will require repairs.

But do not immediately run to the service center and pay big funds to the craftsmen who convince you of the presence of severe malfunctions in the device.

The lawn mower stalls at high speeds

Perhaps more and more a widespread complaint associated with gasoline trimmers sounds like this: “Lawn mowl

Naturally, a rather harsh fault may be a prerequisite for this. A two.stroke trimmer engine for grass does not develop turns stalling. lawn mower FS 130 give gas stalls. But in most cases, the situation is even easier than it seems to be the 1st gaze.

In order to cope with such an inconsistent, first, try to deal with its causes without the help of others, because, having found out the reason, it’s even easier to fight with the inconsistency, and from time to time it is even self.destructive.

In fact, circumstances, this is when the lawn mower stalls at high speeds, there are quite a lot of these circumstances.

Why is a Chinese lawn mower not developing momentum?

gaining momentum. very frequent inconsistency and of course always has a common solution.In this.

The lawn mower is not gaining momentum, the cause of the malfunction and eliminate it

.Removed the grid from the silencer, began to work.

Another, this is the presence of malfunctions in the power system.

will stall at idle. At speed stalls a trimmer for Champion grass. GAPHOLLOSKALL GOODLUCK 4300 stalls video revolutions. The lawn mower stalls when you press the gas. At high speeds, the lawn mower stalls. The problems with the power system may lead to a drainage or incorrect carburetor adjustment.

Vibrations that take place in the process of operation of the lawn mower can lead to a reservoir.

Incorrect adjustment of the lawn mower can be fixed by simply adjusting it in accordance with the requirements specified in the operating instructions.

In addition, sometimes gasoline trimmers for grass can stall due to the fact that the valve located in the gas tank cover just clogged or stick.

To find out, try using a braid by loosening the gas tank cover.

If in this mode the device works properly, clean the valve.

over, the lawn mower can stall due to poor fuel flow into the carburetor

Why then the device starts up, ask you?

The reason for this is that at first the fuel gradually falls into the carburetor and is enough for work with increased power.

However, then it is produced and at large speeds the engine begins to stall.

As for the carburetor, here the problem may also be that its body is too pulled.

The reason that the lawn mower stalls at high speeds

on gas, there may also be an air leak.

We are talking about the possible presence of a place through which air can pass during the heating process of the engine.

Among other things, do not forget to check the fuel intake hose. GAPHOLLOSKALL GOODLUCK 4300 stalls video revolutions. Husqvarna trimmer stalls when loading. The problem may be that it is weak or cracked at all.

These are the main reasons why the gas mowl can stall.

This common problem has a number of different reasons. While working with the device, you can meet both obvious problems, the signs of which are clearly traced, and with asymptomatic cases. The first option is the most simple from the point of searching for the problem. If the trimmer for the grass does not gain momentum, and there are no clear signs of breakdowns, then you will need to sequentially check the most typical cases of malfunctions, and if the reason is detected, eliminate it.

The problem is when the lawn mower is not gaining momentum, it is mainly found in gasoline units. This is the technique of various models, for example, Husqvarna, Champion, Stihl.

With quality products, such problems are less common than with cheap from unknown manufacturers.

Part of the structural elements with which problems can be associated with visual inspection are available, and to verify the functioning of the remaining nodes you will need to disassemble the motorcycle.

Low quality fuel use

The trimmer for the grass does not develop momentum if refined with low.quality fuel. For this reason, the engine can do not start or work with “jerks

trimmer, grass, began, work

“, Changing the speed of rotation of the knife or fishing line.

To independently determine the quality of the used gasoline, the following actions are performed.

  • The candles are removed with a special key.
  • Inspect their working contacts for the presence of a rag of red brick color: if it is, then the fuel used contains significant inclusion of additives.

Candles generally often act as indicators that allow you to determine the malfunctions of the combustion of the gasoline engine, because they can be quickly removed and inspected.

If plaque is detected, it is necessary to drain the fuel filled into the tank and replace it with high.quality. The lawn mower used should be refuel only with those brands of gasoline, which are indicated by manufacturers in the operating instructions. It also follows peel

Air or fuel filter pollution

The next common cause of reducing the number of revolutions on the trimmer is the pollution of its air or fuel filters. In the first case, the problem is that the fuel mixture entering the combustion chamber Not enough saturated with oxygen

, As a result, gasoline does not burn out all. This does not allow the maximum power to develop a motorcycle.

In order to check whether the air filter is really to blame, you need to remove it (first promoting the lid for this) and turn on the lawn mower. If it works fine, then instead of a clogged filter element, you must insert a new.

How to look for malfunctions in the mechanical part

The transmission of rotation from an electric trimmer for grass is performed in the same way as models with an internal combustion engine: an integral shaft works inside the rectangular section of the bar, and a curved cable works.

Their length, diameter and design are selected by the manufacturer for specific dimensions of the composite bar.

Features of the junction of the composite bar

It is made by an adapter with a screw clamp.

The large screw head is made to conveniently adjust the position of the mowing organ at the bottom of the bar. The rotation angle is selected individually.

It is convenient for me to expose it so that the longitudinal axis of the protective casing and the axis of the electric motor are located in the same plane.

In this place, a malfunction associated with the transfer of torque from a direct shaft to a cable may sometimes occur in this place. It is manifested by the fact that at idle engine the trimmer for grass works normally, and already under a small load, the mowing head stops rotating.

trimmer, grass, began, work

The method of its elimination was well shown by the owner of the video “Repair of the Electrimmer” Roman Shapkov. I recommend to see.

Method of attaching a mowing head and a casing

On my trimmer from below the rod, the adapter is fixed with rivets, into which the fastener bolt of the protective casing will be plunged.

The output shaft of a rotating cable has a hexagon at the end. A plastic mowing head is put on it.

From the inside, a return spring of the automatic discharge of fishing line during kosbe is inserted into it.

A spool was inserted into it. It is fastened with a fixing nut from above.

The device of a spitter head with a fishing line is quite simple.

However, all plastic parts do not have high strength, subject to wear. Their working surfaces are erased. After three seasons of work on my trimmer, the output holes of the fishing line from the mowing head expanded, the thickness of the fixing nut decreased.

It is difficult to apply protective measures to wear, and repair of these parts is easiest to fully replace the head. It is easy to buy it: you just need to know the exact dimensions of the hexagon and evaluate the new design according to the working characteristics.

The secrets of the selection of fishing line

Among the frequent malfunctions of the trimmer coil, there are cases when the fishing line for the trimmer ended or simply confused due to improper winding on the spool. It is not difficult to eliminate them.

But in practice, I met with another defect in the fishing line, which was sold on the state retail chain from Patriot LLC company. Her view in the factory packaging.

As I understand it, it is specially hidden in a sealed package: you can not touch when buying.

When I opened the packaging to install the fishing line in the spool, its plasticity immediately caught my eye, and not elasticity. It is easily bending, behaves like a soft wire: when in contact with the grass, it immediately breaks. It is impossible to mow: she managed to return to the seller.

Since then, I have been buying only that fishing line for a trimmer that can be molested in my hands and evaluate its operational properties.

I try to refuse varieties of ordinary round fishing line. I prefer a ribbed shape to them with faces: asterisk, trapezoid, square or triangle. They are better cut off the grass.

How to eliminate increased vibration

Reliably collected trimmer mechanics for grass is well balanced. It provides convenient work. However, bearings can be worn out over time, lose lubrication.

A prefabricated shaft transmitting rotation from the engine of a spool is able to touch the internal walls of the bar, creating excessive friction with heating.

Such a defect can and must be eliminated. This technology is shown by TV repairman with his video “Vibration during the operation of Elektokosa”.

If you still have questions about how to carry out the repair of the electrimmer, then ask them in the Комментарии и мнения владельцев. I will answer.

Subscribe to our “Home Master” newsletter and you will always learn the first about the news of this blog!

Комментарии и мнения владельцев

Elena :

The Eletric trimmer has broken for the Carver TR1200S grass. a plastic hexagonal planting nest on a semi.automatic burst melted and a square screw from a fixing nut flew out of overheating (although they didn’t mow 10 minutes). We cannot choose a similar rogue of another brand. On some site, the man was advised: since the landing size M10x1.25 is the left (although they did not find something in the instructions), the head from Husqvarna 5310060-93 may approach the instructions. But she stands like a new trimmer for grass.What do you advise?

Alexei :

Hello, Elena. Do I understand correctly that you have a new trimmer for the grass and broke down after the purchase? The fact is that in this case the manufacturer’s guarantees act in this case. On his website https: // mcgrp.ru/Manual/Carver/TR-1200S specially looked at the instructions for your model. There is also a forum for users where they ask any question about products and share information. I advise you to discuss this issue with the manufacturer. He values ​​a reputation and should help you. Phone Central Service Center: 7 (342) 218-24-85. I believe that picking up a mowing head by size of mounting is not entirely right. The reason for overheating you did not find out. Twisting transmissions may not coincide. About information in the instructions: it is created for buyers in order to familiarize yourself with the device and operating rules. The drawings of all the details in it do not publish.

Elena :

PAUL :

Tell !pzhl.,How to strengthen the latch (in your text it is called: connecting adapter with a screw clamp) in the connection of the collapsible straight bar, spanks from vibration, does not fix it.

Alexei :

Hello, Pavel. On my trimmer, this knot was made by plates, which are riveted at the turn of the turn, and then the usual screw mount. Everything is simple there. How is your trimmer for grass, this node is difficult to judge. Maybe you will take a picture at least on the phone and send a picture to the mail? Address in the section “On the site”, “Privacy Policy”. See the very bottom.

Sergey :

If the lock is twisted, and there is a supply of a supply on the screw, then the countrogais will help.

Dmitry :

Huter Get-1500SL. The engine rotates slowly. Even if you remove the trimer bar, and pull the engine out of the case, then the rotation is slow, and some strange sound is noticeable. The bearings are good, the lubricant in the nodes is present, the brushes are normal (but by the way they are so tightly settled by the anchor that it is difficult to rotate it with your fingers) the winding is like a whole, everything is visually good. Separately, everything is spinning normally. But when everything is collected, it feels like a bearing died, or a skew. I sin on mechanics, but separately everything is working, and if you collect, it barely twists

Alexei :

Dmitry, hello. Try to rotate a completely assembled engine with your hands, and then pull out the brushes and repeat the operation. Without brushes, rotation should be easy, inertia is felt. If it is not, then there are two options: somewhere there is a place for rubbing the rotor on the stator or clinked some kind of bearing. You need to inspect all this very carefully, especially the lubricant. There may also be some kind of garbage in it. In a word, check the rotation for inertia and by ear. Evaluate all places, look at the lumen. Turn on the voltage only in extreme cases and measure idle currents preferably without nozzles. Compare them with a nominal load.

Michael:

I can not unscrew the bolt of mounting mowing

Alexei :

Michael, they came to me on the mail of the site of your bolt. I’ll try to tell the solution. And it’s very difficult to give recommendations.

Paul :

The spit.head on email constantly flies.trimmer ET 1000 at the junction with a flexible shaft. I can’t understand how it is attached in a bent bar?

Alexei :

| Denial of responsibility | Contacts |RSS