Why does a trimmer for grass holds. Immediately after you started

Trimmer for grass only works at large speeds

Trimmer for grass is not gasoline works on idle

By purchasing a bureau, you should be prepared for the fact that, like all other similar tools, it may also have breakdowns that require repair. But you should not immediately run to the service center and pay large sums to the masters, convincing you of a serious malfunction of the device.

Perhaps the most common complaint about gas trimmers for grass: “Gasoline. Gas trimmer for grass: but that’s not all. Works great with a bushresis. Naturally, a serious malfunction may be a prerequisite for this. But in most cases, even simpler than it can at first seem to deal with this problem, first try to understand its causes without the help of others, because after clarifying the reason it becomes even easier, and sometimes self.Destructive.

In fact, when the motorcycle stops at high speeds, there are many such circumstances. Other. The presence of defects in the mains. Construction and repair simply withstand, and not on a gas trimmer. In this case, the brush will be postponed not married. The trimmer for the grass works quietly, the gearbox is not very hot even at idle. Carbon adjustment or displacement can lead to a dilemma with a power system. Vibration caused by a bushrease can lead to inequality. Incorrect tuning of the bush cutter can be fixed by simply adjusting it in accordance with the requirements specified in the operational annotation.

Benzotrimer (China) Mongend adjustment, the coil rotates as soon as it starts in standby mode

Chinese benzo was brought for repairs of a trimmer for grass (a pronounced rotation back, no need to do.

In addition, gas trimmers for grass can sometimes linger due to the fact that the valve located in the gas tank cover simply clogs or gets stuck. To find out, try using a braid, loosening the gas tank cover. If in this mode the device works correctly clean the valve.

In addition, the cut of the brush can be detained due to the unpleasant flow of fuel in the carburetor. However, repairs, that is, works normally at low speeds. You ask why then the device starts? The reason for this is that initially the fuel gradually enters the carburetor and it is enough to work at high power. Gasoline is not idle. But then it develops and at high speeds the engine begins to slow down. As for the carburetor, the problem here may also be that its case is very dense.

The hood of air can also be a prerequisite for mowing gas, which stops at high gas speeds. We are talking about the possible presence of space through which air can pass during the engine heating.

First of all, be sure to check the fuel hose. The problem may be that it usually holds well or cracks.

These are the main prerequisites for stopping the brush.

When pressing gas

If the lawn mower stops when pressing the gas, then the reasons may be the following.

  • The most common option is Carburetor adjustment failure. Which occurs with significant loads on the drive, after prolonged inaction of the mechanism or when using it in severe conditions.
  • Flaw valve clogging. Which eliminates it with the message, as a result of which gasoline according to the system begins to flow normally.
  • The weakening and hanging of the cable in the carburetor. It can also arise Stretching of the fuel hose up to its break, caused by the action of a significant load.
  • The clogging of the sapun (check valve), as a result of which fuel does not enter the tank.

If the problem is associated with the carburetor node, then it can be recognized by the appearance of vibrations of the lawn mower. Когда лопается шланг или растягивается трос — выполняют замену данных комплектующих.

What to do if the lawn mower stalls when you press the gas

Most often during the periods when the lawn mower stalls when the gas is added, the cause will be the air damper, more precisely, its condition: it clogged. Structurally, the part is located in the place where the resulting fuel is sprayed behind it, and, accordingly, the product collects all inclusions in low.Quality gasoline. To eliminate the problem, you just need to clean it. The same situation can occur with a filter clogged, but it is eliminated similarly. Total, we specify the reasons for which the tool is led to the gas to the stalled state:

  • A clogged air damper;
  • The clogged filter is fuel, and when you give gas, this is especially noticeable;
  • The air of the crankshaft shaft occurs;
  • Damaged gasket between the cylinder and the carb.

When you cleared, washed and blowing the elements, but again the lawn mower stall when you press the gas-replace them with new ones, check the quality of the fuel, as well as the literacy of the proportions of the cooked mixture. When opening the air damper, the tool will stall for the following reasons:

  • Dosage carburetor.
  • The appearance of cracks on the fuel hose caused air leaks.
  • The occurrence of problems with the oil seals.
See also  What is the best reel for grass trimmer?

In the process, there are situations when the lawn mower at high speeds is subject to a similar sharp stop. It occurs for the following reasons:

  • Due to problems with the circulation of the fuel mixture;
  • With air leaks;
  • The fuel intake hose is poorly connected or cracked and cannot be used;
  • Stab or clogged the valve of the cover of the gasoline tank;
  • The carburetor was resolved.

In most cases, nevertheless, the cause will be a carburetor and related filter, hoses. If you need cutting gear or trimmer heads, then our site will also offer them to buy them with gasoline tools and components for them.

At idle

At single speeds, the common reasons for stopping a trimmer for grass are as follows:

  • Reducing the speed of the gearbox when heating it, which is a consequence of the use of inappropriate fuel mixture;
  • Clogging of the throttle;
  • Air entering the system;
  • Not enough fuel for the operation of the lawn mower.

If a carburetor is a problem place, then the technique will stop at the “cold” and with a “hot” launch.

The chainsaws are stalling or not starting up for gas: the main reasons and ways to eliminate them

The chainsaw does not have a too complex system, but at the same time requires careful care. Many people forget about the elementary rules during the operation of the chainsaw, and this significantly reduces the life of its operation. Basically, with regular violation of some rules, problems appear.

For example, a chainsaw may not start or stall after gas pressing. In such a situation, the first thing you need to find out the reason for the breakdown and try to fix it yourself.

Checking the main chainsaw systems

If the chainsaws immediately after turning on, then there was a breakdown of some part of the equipment. It is impossible to instantly identify the cause, so you need to check all the details sequentially.

First of all, it is necessary to check the fuel tank of the chainsaw. The fuel may simply not be enough for full.Fledged work, so it is necessary to prepare the mixture in accordance with the norms of mixing oil and gasoline. Gasoline should have the maximum octane number, and the oil is usually selected according to the instructions in the operating book.

If the reason is not in the amount of fuel, then the next cause of the breakdown may be the spark plugs. Not only the spark plugs are checked, but also a high.Voltage wire from the tips. The gap in the candle should be no more than 0.5 mm.

If the distance of the gap is too small, it means that the candles have deposited a carpet that needs to be cleaned, and then install the parts in its place and check whether the chainsaws are started or not. It is also recommended to replace the candles with new ones from time to time, even if they are in good condition.

Another reason that the chainsaw stalls after pressing the gas can lie in the breakdown of the carburetor or fuel filter. Cleaching your own fuel filter is quite simply unlike a carburetor, which has a more complex design and therefore this detail is best entrusted to specialists.

Why does the chainsaw not start or stall at idle?

There are times when the chainsaw stalls at idle speeds. Most often, the reason is the pollution of the muffler, which can be easily cleaned without the help of specialists. You can also solve problems using carburetor settings. On this part of the chainsaw there are two bolts with letters L and H. The bolt called L is responsible for the revolutions of the chainsaw.

To increase idle, it is necessary to turn the bolt by half a turn, and perhaps this will solve the problem. We must not forget that a carburetor is a rather complicated system and its adjustment may not be able to be a simple person. If the speed is incorrectly set, then you can deform the internal system of the chainsaw, so it is better to entrust this work to professionals.

What to do if the chainsaw is stalled at load?

Very often, chainsaws with a powerful power device stall from increasing load. The reason here can only be in the contamination of the fuel filter or in the gas tank. It is best to replace a completely fuel filter with such a problem, especially since it is not too expensive. If this did not help, then it is recommended to check the quality of the mixture.

Precisely, you need to prepare a new fuel mixture, after replacing gasoline. Maybe the whole thing is just as gasoline, and the low octane number simply does not allow the engine of the chainsaw of sufficient power at excessive loads.

Basil stalls with increasing speeds

In cases where the chainsaw begins to stall at high speeds, you need to check the details such as:

The air filter is greatly clogged during the work, so it needs to be cleaned and, perhaps, even washed under warm water, but before installing it it will be necessary to dry the part well. After that, the fuel hose is disconnected from the carburetor.

If the liquid does not flow through it, then it just hid and it is recommended to clean it or buy a new hose. If the mixture flows through the fuel hose in full, then the filter can not be checked. In all other cases, it is necessary to clean the soundtress with an ordinary needle, and replace the gasoline filter or rinse.

The reason may even lie in a gasoline pump. We are talking about checking the wear of this detail. If the fuel seeps through the walls of the gasoline pump, then it should be replaced. If the fuel does not seep through the walls, it means that the reason that the chainsaw is stalling at high speeds not in this.

The main reasons for the gas station breakdown

Although all possible breakdowns were described in some certain parts of the chainsaw system, their solutions may not be enough. You need to dwell on some aspects of solving problems in more detail.

See also  Adjusting the grass trimmer carburetor with your own hands

Checking the fuel mixture and candles

The fuel mixture, which is poured into a chainsaw, must be pre.Prepared.

First of all, we must not forget that in the manufacture of the fuel mixture, it is necessary to use only high.Quality and allowed components allowed according to the operating book.

We must also forget that the fuel is best drained before the conservation of equipment or between seasons, when the chainsaw is idle.

Checking the spark plugs can be divided into several subparagraphs. Firstly, you need to remove the spark plugs and check their tips for the presence of fuel. This can happen from time to time when a chainsaw starts up. Most often, this happens to inexperienced users who simply forget to follow the rules of the sequence when a chainsaw is started at cold speeds.

Secondly, on the spark plugs there may be a carpet that simply clogs the clearance of the connection. The gap should have a distance from 0.5 to 0.65 mm. Remove the soot with fine.Grained sandpaper or brushes with metal hairs.

does, trimmer, grass, holds, immediately

Deliciper checking and cleaning

It happens that the check of absolutely all the components from the hose to the spark plugs does not give a result and the chainsaw continues to stall when the gas is pressed. In this case, it remains only to check the muffler.

What to do if a trimmer for grass stalls when you press the gas?

So why is a trimmer stall for grass when pressing for gas ? There may be several reasons for this problem.

  • The carburetor was resolved after an unsuccessful wintering or after too intense use of motorcycles. The gasoline trimmer for the grass operates on the air-fuel mixture that the carburetor prepares it. With improper adjustment, this mechanism prepares a depleted mixture that is not capable of providing the engine with quite high speeds. You can understand about the problem with the carburetor by the characteristic vibrations of the lawn mower.
  • You will learn about the clogging of the fuel filter by the fact that the trimmer for the grass starts and stalls. In other words, the flow of fuel is enough to start a motorcycle, but is no longer enough to maintain the engine in work. It may be possible to solve the problem with weakening valves on the filter. If not, you should rinse the filter in solvents and blow it with compressed air. If after and this is not solved the problem, then you should purchase a new fuel filter.
  • If the engine stalls at speeds close to maximum, then perhaps the problem with the saope that regulates air access to the gas tank. If the fuel consumption is too fast, characteristic when you give gas, rarefied pressure is formed in the gas tank, due to which the fuel flow into the engine is reduced.
  • The engine stalls when opening the damper. The problem, again, is associated with a carburetor, which, due to an excess of air, prepares a depleted air-fuel mixture, which is not capable of ensuring engine operation.

Trimmer for grass does not gain momentum. What to do?

Trimmer for grass does not gain momentum. Very frequent inconsistency and of course does not always have a common solution.In this.

In this case, the lawn mower will stall at idle. The lawn mower does not develop speed, reason | Funnydog.TV. Dilems with the power system may lead to a drainage or incorrect adjustment of the carburetor.

Vibrations that take place in the process of operation of the lawn mower can lead to a reservoir.

The incorrect adjustment of the lawn mower can be corrected by simply adjusting it in coordination with the requirements indicated in the operating annotation.

Apart from time to time, from time to time, gasoline trimmers for grass can stall due to the fact that the valve located in the gas tank cover just clogged or stick.

To find out, try to use the braid by loosening the gas tank cover.

If in this mode the device works in an affirmative way, clean the valve.

Over, the lawn mower can stall due to the disgusting receipt of fuel in the carburetor

Why then the device starts up, ask you?

The reason for this is that at first, the fuel gradually runs into the carburetor and is enough to work at high power.

But then it is produced and at huge turns the engine begins to stall.

As for the carburetor, here the problem may also consist in the fact that its body is very pulled.

The prerequisite is that the lawn mower stalls at high gas speeds, there may also be an air leak.

We are talking about the likely presence of a place through which air can pass in the process of heating the motor.

In addition to everything else, do not forget to check the fuel intake hose. Trimmer for grass does not develop turns. One of the reasons. The inconsistent may be that it holds weakly or in general cracked.

These are the main prerequisites why the lawn mower can stall.

10 best electric trimmers, the characteristic in the ranking, many owners of private houses and cottages carefully care for a personal plot. When the active growth of grass begins, then there is a need for special technology. The modern market offers a choice of lawnmands, lawnmands, electric trimmers for grass. The latter are favorably different in.

Gasoline trimmers for grass help to put things in order on a suburban area. If the electric ships are suitable only for the “cosmetic” haircuts of lawns, then the lawn mowers are used for the all.Encompassing chosen select a gasoline trimmer for the grass for giving. Overview of benzotrimers. The best design contributes to the highest productivity of the tool, the width of the mowing of the compass.

Restring a 2 sided spool on a string trimmer weed eater EASY!!

The lawn mower is one of the main instruments of the summer resident used to quickly bring the land in order. The owners of private houses acquire this weapon for mowing grass in the personal territory. The period of active use of benzos and electric trimmers falls on the summer period. Before starting operation, the tool is brought into working condition: the rubbing parts are lubricated, the cutting headset changes, the fuel mixture is poured into the tank. If the engine does not start or stalls quickly, without gaining enough revolutions, then you have to look for the causes of problems and eliminate the identified malfunctions. To carry out the repair of the lawn mower with your own hands, you need to understand its device and the principle of operation of the main nodes. This information can be found in the operating instructions, which the manufacturer applies to garden equipment without fail. Check for such a manual when buying a chainsaw. The import tool should be accompanied by instructions written in Russian.

See also  replacing the bobbin on the trimmer. Tools for replacing the trimmer head.

A long tubular bar is attached to the gearbox of a two.Stroke internal combustion engine. Inside the rod passes a shaft transmitting torque from the gasoline engine to the cutting mechanism. Fishing line for a trimmer or knives rotate with a frequency of 10,000 to 13,000 revolutions per minute. In the protective case of the gearbox, the presence of holes is provided, into which a lubricant is introduced using a syringe. For the convenience of using the tool, the manufacturer equips it with a special adjustable belt thrown over the shoulder.

The cutting headset is attached to the gas codes:

  • Lines for a trimmer, the thickness of which varies from 1.6 to 3 mm, is located in a trimmer head. During the mowing of the grass, the fishing line for the trimmer is worn out. The fishing line is replaced quickly and easily in two ways: by winding the fishing line of the same diameter on the bobbin or by installing a new coil with an already wound fishing line.
  • Steel knives with bilateral sharpening a lawn mower to cleanse the site from weeds, small shrubs, hard herbs. Knives differ in shape, as well as the number of cutting surfaces.

On the U-shaped, D-shaped or T-shaped handle attached to the bar, there are tanosa control levers. The cutting mechanism is fenced with a special casing. Domestic motorcycles are refueling with a mixture prepared from gasoline and oil, which is poured into the fuel tank. The device of semi.Professional and household motorcycles equipped with a four.Time gasoline engine is slightly different. The gas station is also different: the oil is poured into the crankcase, and gasoline is in the tank.

A measured piece of fishing line is folded so that one end is longer than the second by 15 cm. We put the loop into the slot on the coil, and begin to wind up in the direction indicated by the arrow

What to do if a trimmer for grass stalls when you press the gas?

So why is a trimmer stall for grass when pressing for gas ? There may be several reasons for this problem.

  • The carburetor was resolved after an unsuccessful wintering or after too intense use of motorcycles. The gasoline trimmer for the grass operates on the air-fuel mixture that the carburetor prepares it. With improper adjustment, this mechanism prepares a depleted mixture that is not capable of providing the engine with quite high speeds. You can understand about the problem with the carburetor by the characteristic vibrations of the lawn mower.
  • You will learn about the clogging of the fuel filter by the fact that the trimmer for the grass starts and stalls. In other words, the flow of fuel is enough to start a motorcycle, but is no longer enough to maintain the engine in work. It may be possible to solve the problem with weakening valves on the filter. If not, you should rinse the filter in solvents and blow it with compressed air. If after and this is not solved the problem, then you should purchase a new fuel filter.
  • If the engine stalls at speeds close to maximum, then perhaps the problem with the saope that regulates air access to the gas tank. If the fuel consumption is too fast, characteristic when you give gas, rarefied pressure is formed in the gas tank, due to which the fuel flow into the engine is reduced.
  • The engine stalls when opening the damper. The problem, again, is associated with a carburetor, which, due to an excess of air, prepares a depleted air-fuel mixture, which is not capable of ensuring engine operation.

How to change the trimmer line on a Ryobi 18 volt cordless string trimmer

For what reason does an electric braid for STIHL grass do not develop full power

When using an electric trimmer for the grass, non.Aviation problems may also occur. Here the reasons are completely different than that of fuel cos.

You can eliminate problems yourself

Eletric trimmer for grass does not develop the required power, because:

  • The voltage in the network is below the required minimum for the device more than 10%;
  • There was a failure on a smooth launch (if there is such a system);
  • There was a malfunction of the brush node;
  • The engine winding was burned;
  • Rotating parts sometimes jamming.

To establish voltage, you should first check its power. If it does not meet the norms, it should be increased using a stabilizer.

The repair of the smooth start system is carried out only in the service center.

With wear of brushes, you just need to replace them. When installing new ones, it is recommended to clean all the surfaces with which they contact.

To establish voltage, you should first check the power.

When burning engine windings, you need to change the electric motor.

Jamming of parts of rotation can occur for various reasons. To eliminate them, you should review the entire drive unit.

The last problem may also arise in another unit of this company. The STIHL prisoner, and the sharpening of the disk on the scissors will be its solution.

| Denial of responsibility | Contacts |RSS