Why is a trimmer for grass heats up and the speed is falling. Problems with ignition candles

Trimmer for grass loses power to hot. The lawn mower does not develop full power

A braid braid with a gasoline drive is a useful thing for owners of personal plots, lawns, and when a trimmer for grass suddenly stalls, the work on cleaning the territory stops from the grass. The device itself is a rather complex mechanism, so there are many different causes of its breakdowns. The most common problems contain instructions for operating. Know the reasons why the trimmer stalls for the grass, it follows to independently effectively perform the repair of the device.

Malfunctions with a benzocosa associated with the fact that this device is not started, in a certain way are classified by specialists of service services. They stand out malfunctions with the following nodes of the mechanism:

  • the engine in which the piston and bearings can be worn out or fail to crack the crankcase;
  • the fuel supply system, while it is possible to clog the filter or problems with the carburetor;
  • mechanical damage to wires, tubes, hoses;
  • The ignition chain.

To correctly determine the knot where the breakdown occurred, it is necessary to pay attention to the circumstances of the trimmer stalls for the grass.

When pressing gas

If the lawn mower stops when pressing the gas, then the reasons may be the following.

  • The most common option is Carburetor adjustment failure, which occurs with significant loads on the drive, after prolonged inaction of the mechanism or when using it in severe conditions.
  • Flaw valve clogging, which eliminates it with the message, as a result of which gasoline according to the system begins to flow normally.
  • The weakening and hanging of the cable in the carburetor. It can also arise Stretching of the fuel hoseup to its break, caused by the action of a significant load.
  • The clogging of the sapun(check valve), as a result of which fuel does not enter the tank.

If the problem is associated with the carburetor node, then it can be recognized by the appearance of vibrations of the lawn mower

trimmer, grass, heats, speed

Когда лопается шланг или растягивается трос — выполняют замену данных комплектующих.

trimmer, grass, heats, speed

What could break

Malfunctions with a benzocosa associated with the fact that this device is not started, in a certain way are classified by specialists of service services. They stand out malfunctions with the following nodes of the mechanism:

  • the engine in which the piston and bearings can be worn out or fail to crack the crankcase;
  • the fuel supply system, while it is possible to clog the filter or problems with the carburetor;
  • mechanical damage to wires, tubes, hoses;
  • The ignition chain.

To correctly determine the knot where the breakdown occurred, it is necessary to pay attention to the circumstances of the trimmer stalls for the grass.

Ways to eliminate breakdowns

Subsequent work is likely on the carburetor:

  • cleaning and adjustment of the fuel supply valve;
  • similar work with a valve producing redesigned gases and pairs (after burning fuel);
  • replacement of the spring more weak on the entrance valve;
  • restoration of the tension of the carburetor cable;
  • replacement of the fuel leaks hose, verification and strengthening of a weakened connection;
  • changing the rotor damper disk;.
  • Change of faulty wire or ignition coil.

Immediately after the start

Smelting Motokos or a trimmer for the grass after starting is justified by subsequent reasons:

  • impressive of previously adjusted valves;
  • first the wrong settings of the valve mechanism;
  • clogging with deposits of the fuel supply valve;
  • the hose is worn or poorly annexed.

Due to the violated method of injection of a fuel, a lawn mower or a trimmer for grass is very vibrated in work.

Trimmer for the grass is very hot

Overheating of a trimmer for grass can occur for many reasons:

  • Gasoline does not have an octane number specified in the instructions for the device;
  • The proportions of gasoline and oil were not observed in the preparation of the fuel mixture;
  • The mixture of fuel and oil was prepared for a long time (the mixture cannot be stored for more than 2 weeks);
  • The trimmer for the grass works for a given time;
  • A trimmer for low.power grass is used on dense and solid grass, the device works with overload and heats up quickly;
  • Displacement towards the bar or the cassette cover stuck.

The latter will happen if you install the mower is not suitable for this device, or when the axis is shifted to the arrow. These changes complicate rotation, increase the load on the engine, and it overheats.

Diagnosis and elimination of electric motor problems

Electrimmer malfunctions can be as follows:

To cope with these breakdowns, you do not need to disassemble the entire device.

With serious engine failures, you will have to disassemble it. To do this, you need to unscrew a few screws. Having gained access to the motor details, you need to carry out the following actions:

  • Checking the degree of worn in brushes. unsuitable details will need to be replaced with new ones;
  • Rall the engine winding. the resistance should be high;
  • Check the stator and rotor. to test the rotor winding with a multimeter, measure the resistance: large deviations from the norm indicate a malfunction, the absence of resistance on the stator winding also indicates a breakdown (the same way is diagnosed with the stator case).

Low.speed problems are a common phenomenon for cheap trimmers. However, with improper maintenance, such manual mowers as Huter, Patriot 3055, Echo also suffer from this.

Diagnosis and elimination of electric motor problems

Electrimmer malfunctions can be as follows:

To cope with these breakdowns, you do not need to disassemble the entire device.

With serious engine failures, you will have to disassemble it. To do this, you need to unscrew a few screws. Having gained access to the motor details, you need to carry out the following actions:

  • Checking the degree of wear of brushes. unsuitable details will need to be replaced with new ones;
  • Rall the engine winding. the resistance should be high;
  • Check the stator and rotor. to test the rotor winding with a multimeter, measure the resistance: large deviations from the norm indicate a malfunction, the absence of resistance on the stator winding also indicates a breakdown (the same way is diagnosed with the stator case).

Low.speed problems are a common phenomenon for cheap trimmers. However, with improper maintenance, such manual mowers as Huter, Patriot 3055, Echo also suffer from this.

The trimmer for the grass is not started due to the malfunction of the carburetor

One of the most difficult reasons for the impossibility of launching a lawn mower is a carburetor. This mechanism is responsible for the preparation and good supply of the fuel-air mixture to the cylinder. If the carburetor is clogged or adjusted incorrectly, then the lawn mower may not start or work unstable. Detailed instructions on how to adjust the carburetor on a benzocosa is described in this material.

If the adjustment does not help restore the stable operation of the tool engine, or the trimmer for the grass does not start at all, then the carburetor should be removed and repair it. The entire repair of the carburetor is that you need to disassemble it, clean all channels and constituent elements. If necessary, replace the failed details. membranes, filters, etc.P.

If the suspicions fell on the carburetor, then you should pay attention to the following types of malfunctions:

  • Canals and nozzles clogged. special liquids can be used for cleaning, however, it is best to disassemble the mechanism with its thorough flushing. The reason for the clogging of the channels and jackets of the carburetor is the storage of a tool with fuel in the tank
  • Wear of the carburetor gaskets. rubber seals contribute to the fact that the tightness of the mechanism is disturbed, as a result of which the serviceability of the functioning is violated
  • Memory of carburetor membranes. they are responsible for downloading fuel to the device

To make sure the CPG malfunction, you should check the compression, which is described above.

Immediately after you started

The unit can stall immediately after the launch, if the carburetor is cesspool or was incorrectly configured. this causes Uneven fuel supply

The result is that the device begins to vibrate clearly. To eliminate problems, the carburetor is reconfigured, acting according to the instructions for the mechanism.

The engine also stops when Clotting of the valve

, supplying fuel. In such cases, it is enough just to clean it. If the lawn mower at first earned, but then immediately stalled, then possible fuel to the carburetor unit enters some difficulty. The weakening of the valve helps to solve the issue, which provides free circulation of the mixture in the system.

The stop may also be called Air suction

In the presence of mechanical damage to the hose (holes, cracks) that fuel fuel fuel. In this case, the drive should be added to the drive to quickly drive air bubbles from the system.

When opening an air damper

It happens that the unit stalls when opening an air damper, working normally at idle. This is due to the air leaks of the system caused by the presence Cracks of the fuel hose

or problems with seals. The carburetor dosing system can also work malfunctioning, while the lawn mower will stop after the opening of the damper.

All possible reasons that the lawn mower stalls, and the methods of eliminating them are contained in the next video

There are many reasons for stopping Motokos, but the most commonly occur in work related to its carburetor. They can arise in any case. The most problematic option is when there is a serious breakdown, and you will need to purchase new parts or change the lawn mower.

So that the trimmer for the grass works normally for a long time, you should strictly comply with the requirements of the operating instructions. It is necessary to refuel the unit suitable for it in the composition with a fuel mixture, the device should work with a moderate load.

Preventive measures and operating rules

So that the lawn mower does not work and does not stall when starting, it must be correctly stored and operated. Compliance with the following simple recommendations will forget about problems.

  • When begging the grass, you need to monitor the state of the cooling system. It is also necessary to regularly clean the channels in the case and starter’s ribs.
  • To clean the tool, you should use kerosene, solvent, or other washing tools.
  • You can not clean a hot tool. it must cool before washing.
  • It is important to observe the recommended working mode. this will avoid overheating of the engine.
  • If a braid for grass is not used over the next thirty days, the fuel must be drained, otherwise it will fall into heavy components that can score the channels of the carburetor.
  • After the fuel is merged, the trimmer for the grass should work at idle for some time until it turns off. This will allow you to completely get rid of the rest inside the working mixture.
trimmer, grass, heats, speed

To store the tool in cold weather, you need:

  • inspect the condition of the parts, eliminate all defects that can be corrected;
  • pour the required amount of oil into the gearbox;
  • Clean the air filter;
  • perform partial disassembly of the engine, wash all moving parts, blow and lubricate thoroughly;
  • To lubricate the piston, unscrew the candle, then raise the piston to the upper dead point by the starter, pour a small amount of oil into the hole for the candle and do the crankshaft several times.

Important! If there is no way to store a trimmer for grass in a warm dry room, you must first wrap the motor with an embarrassed rag.

Only by observing these rules, you can be sure that the lawn mower will work properly and will not stall for a number of seasons.

As you can see, stopping the work of a trimmer for grass can be caused by many reasons. Most of them can be fixed independently using the user instructions. In cases where there is no self.confidence, the equipment is recommended to be attributed to repairs. It is worth remembering that incorrect actions can cause even greater harm to the trimmer. As a result, the repair of Motokos will cost a much larger amount than it would be initially, and in the worst case, it may be necessary to buy a new unit.

The best lawnmands

A braid braid with a gasoline drive is a necessary thing to owners of personal plots, lawns, and when a trimmer for grass stalls at one moment, the work on cleaning the area from the grass stops. The device itself is essentially a rather difficult mechanism, therefore there are many different circumstances of its breakdowns. Most often, the emerging problems contain an annotation for operation. Know the prerequisites for why the trimmer stalls for the grass, it should be that without the help of others to perfectly perform the repair of the device.

Problems with a benzocosa, associated then that this device is not started, are specially classified by specialists of service services. They stand out malfunctions with such nodes of the mechanism:

  • the engine where it can be worn out in other words, the piston and bearings can fail, crack the crankcase;
  • a fuel supply system, with all this, you will clog a filter or a task with a carburetor;
  • mechanical damage to wires, tubes, hoses;
  • The ignition chain.

In order to correctly find the knot where the breakdown occurred, it is necessary to control the circumstances of the trimmer stalls for the grass.

If the lawn mower stops when pressing the gas, then there are subsequent prerequisites.

  • The more increased option is a carburetor adjustment failure that appears with significant load loads, after a prolonged inaction of the mechanism in other words when it is used in languid criteria.
  • The clogging of the fuel valve, which eliminate it with the message, and as a result, gasoline according to the system begins to flow normally.
  • The weakening and hanging of the cable in the carburetor. There is also a tensile of the fuel hose directly to its gap, caused by the action of a significant load.
  • The clogging of the soundtress (revolutionary valve), for this reason, does not enter the fuel in the tank.

The gasoline trimmer for grass stalls at idle

Often, when reducing the speed, the motor motorcycles stalls and does not support idle speed when re.starting. The main reasons for the occurrence of such a breakdown include pollution or the dumping of the carburetor, as well as clogging of the air filter.

Gasoline trimmer for grass stalls at idle

Kobalt 40v Weed Trimmer SUIT UP #shorts

In case of violation of the optimal settings of the carburetor, it is necessary to clean it and repeated adjustment. You can cope with clogging the air filter of a trimmer for grass by placing it for several hours in a solution with a conventional domestic detergent. If independent cleaning has not helped to cope with the blockage, it is better to purchase a new filter element in accordance with the operating manual.

How to Replace String trimmer Line in Under 30 Seconds.

After the measures, the user will not encounter a situation for a long time when a trimmer for grass stalls in idle and functions only when gas supplies.

Why stall the lawn mower at a load

How not to get confused if the lawn mower does not start

The tool, despite its small dimensions, represents a complex technical device. If we study the operating annotation, there will be prerequisites why the lawn mower is not started, known and eliminated. It is necessary to alternately exclude the reasons that make it difficult to start the tool. Why is a trimmer for grass stalls when pressed at high speeds. The lawn mower stalls. They usually start with more affordable nodes with a slight checking check.

When to contact the workshop

If the device is under warranty, at the first signs of incorrect operation, it can be safely attributed to a specialized workshop. Repair will be made for free, regardless of the nature of the damage, if it happened not due to the fault of the owner. In case of breakdowns in the engine, an ignorant person in technology, it is better to immediately contact a specialist. In any case, the degree of seriousness of malfunctions with the unit is determined by the user himself.

Summarize. Both gasoline and electric trimmers for grass are designed for many years of reliable work. Most of the problems described above occurs due to the insufficient attention of the owner to his assistant. Subject to strict compliance with the requirements from the manufacturer and regular maintenance, the manual mower will work rhythmically and without interruptions.

For what reason does an electric braid for STIHL grass do not develop full power

When using an electric trimmer for the grass, non.aviation problems may also occur. Here the reasons are completely different than that of fuel cos.

You can eliminate problems yourself

Eletric trimmer for grass does not develop the required power, because:

  • The voltage in the network is below the required minimum for the device more than 10%;
  • There was a failure on a smooth launch (if there is such a system);
  • there was a malfunction of the brush node;
  • The engine winding was burned;
  • rotating parts sometimes jamming.

To establish voltage, you should first check its power. If it does not meet the norms, it should be increased using a stabilizer.

The repair of the smooth start system is carried out only in the service center.

With wear of brushes, you just need to replace them. When installing new ones, it is recommended to clean all the surfaces with which they contact.

To establish voltage, you should first check the power.

When burning engine windings, you need to change the electric motor.

Jamming of parts of rotation can occur for various reasons. To eliminate them, you should review the entire drive unit.

The last problem may also arise in another unit of this company. the STIHL prisoner, and the sharpening of the disk on the scissors will be its solution.

| Denial of responsibility | Contacts |RSS